The fresh water system and the recipe parameters makes a huge impact on the taste and a tiny impact on the environment as it consumes barely 7 watts when not brewing. We hope that you will enjoy your new Hipster brewer. With best wishes Copyright 2019 All rights reserved 3TEMP/PLAE2TECH Hipster 1grp...
Do not use this appliance for anything other than intended use. Any maintenance other than cleaning should be performed by authorised person. Do not install the machine in environments in which the temperature is 0 C or less. Do not use outdoors. Hipster 1grp...
We reserve the right for any errors in text or images and any necessary changes made to technical data. In the event of technical problems or any questions. Please contact our [email protected] The appliance is only to be installed in locations where it can be overseen by trained personnel.
Page 8
Only use original spare parts. The use of spare parts not approved by the manufacturer could lead to fires, electric shocks or personal injury. Do not place on top of any other appliance. Appliance must not be cleaned by a water jet. Hipster 1grp...
3. Before first use Remove all packaging materials attached to your Hipster 1GRP. Ensure that you have removed all parts and accessories before discarding the packaging. Clean parts and accessories, filter, basket and thermos. Use warm water and a gentle dish washing liquid and rinse well.
Rev.100318-01-v1 4.2 The cycle of The Hipster taste-profiling Pre-brew phase End phase Target ”Regular” brewer Time + Blooming Pre-brew phase End phase End phase Hipster 1grp...
The machine is placed on the counter. Adjustable feet for levelling. Capacity: 1x3,8 lit 200 cups/h. Dimensions: W330mm/D570mm/H665mm. Weight: 28 kg. Max power hot: 230V 1x2400W. Max power cold: 1x38W. Max power idle: 7 W. Water Inlet Water Inlet Power Input Power Input 570mm 330mm Hipster 1grp...
Hipster Brewer 1 GR CAN cable to button Warning! Nr 5. The black CAN-cable is for the button controller only. Do not connect to the router. HIPSTER 1GRP 1. RJ45 to LAN 2. Modem 3. Power unit modem 4. Power unit Hipster 5.
Rev.100318-01-v1 7.2 Adjust the feet 7.3 Adjust the brewer hat in level. Caution! Make sure the brewer hat is in level, or it will not extract evenly in the filter basket. Use a spirit-level . Hipster 1grp...
Start the router 1 minute before the coffee machine, to get an IP-address. Start the machine. Press ON button. A short beep sound means the brewer is on. After 3-8 sec long beep means that the brewer have received an IP-address. Start a run cold. 300-400 ml will be dispensed, Hipster 1grp...
Run Calibrate 2. 2,0lit of hot water is dispensed. Run Calibrate 1. 1,8lit of hot water is dispensed. . Now the Hipster 1GRP is installed. You are now ready to brew! See page 19. 7.6 Machine status State number State name...
Add filter to the brew basket. Add coffee into the filter. Note! Make sure the coffee is spread Note! Make sure the filter fits correct. evenly and the surface is flat. Use 3TEMP coffee filter paper. Hipster 1grp...
Rev.100318-01-v1 Reinstall the brew basket. Ready to brew. 8.2 Select recipe Select a recipe. Adjust grams or millilitre. If needed. Hipster 1grp...
Page 21
Caution! The metal parts of the brewer hat will be very hot. Brewing is in progress when the blue When the brew is finished, the indicator indicator is flashing. light turns green and a beep is heard. Hipster 1grp...
Rev.100318-01-v1 8.3 Thermos detachable serving base Place the cup on the white spot. Place the thermos and place it on the detachable serving base. Click! Press for coffee. Warning! Hot coffee. Press Hipster 1grp...
Note! If you want to save the recipe, Press SAVE before start. If not, the recipe will go back to previous settings. Press the PEN-symbol at the right. Select the parameter you want to change. Press. Adjust the amount. Press to rename the recipe. Press SAVE to keep the recipe. Hipster 1grp...
(Disabled recipe is still in the machine but does not show when pushing “Recipe 1-8” in normal mode). Button 3: Step Down/Back/Previous item (-) in every menu. Button 4: Step Up/Forward/Next item (+) in every menu. Button 5: Previous menu/Back/Cancel Button 6: Next Menu/OK Hipster 1grp...
Page 25
. Repeat step 6 and 7 until “Confirm Save” appears. Confirm by pressing . Menu is now back in “Edit recipe”. Select another slot by using repeating steps 2-9 or leave “Programming mode” by pressing Note! Button always moves back to previous selection. Hipster 1grp...
Page 26
Enabled/Disabled status of slot. 3. Press to enter “Confirm Enable/Disable”. 4. Press to confirm Enable/Disable slot. Note! Button always moves back to previous selection. HIPSTER recipe start/stop grams of coffee setup thermos Hipster 1grp...
Use a soft cloth to clean the drip tray. Important! Keep the coffee machine clean. Caution! Do not use liquids other than water. Danger! Appliance must not be cleaned dy a water jet. Hipster 1grp...
11.2 Cleaning Thermos Remove the brew basket from Clear any object free from the brew basket. the brewer hat. Make sure the thermos is empty. Cleaning Tablet (Part Nr :100204) Caution! Protect your eyes. Warning! Keep away from children. Hipster 1grp...
Page 29
Rev.100318-01-v1 Reinstall the brew basket and the thermos. Choose suitable recipe. 3TEMP recommend 2,5 lit. Press Start. Wait for the brew process to finish; Press STOP to interrupt the brewing process. Hipster 1grp...
Page 30
1 -2 hour in the thermos. Warning! Hot water. Protect your eyes. Clean it with a dish brush. Rinse out several times! Caution! Make sure that No cleaning fluid is left in the thermos. Rinse out properly. Hipster 1grp...
. Remove screws (A) and detach shower screen (B). Warning! Hot water. Protect your eyes. Clean water strainer using the dissolved Reassemble shower screen. cleaning solution prepared in step 1. Caution! Tighten all screws evenly and make sure water strainer is in level. Hipster 1grp...
Rev.100318-01-v1 13. Single brew Cup holder Coffee filter Hario wire insert Brew basket Start a recipe for single brew. Note! To set a recipe see page 24. Hipster 1grp...
Water filter installation kit typ 1 500243 typ 2. 500249 Wire insert 500913 Wire insert for single brew 500953 Wi-fi router and tablet 600919 230 3G 600920 UK 4G 600920 240 4G 600920 US 4G Non-return valve 550038 Hipster 1grp...
Since there is no boiler with preheated water you can also brew with the cold water that comes into the brewer from your water mains. To order the cold brew function; contact [email protected]. Button controller Button controller 6 buttons with display or 8 buttons without display.
This warranty covers faults occurring during the warranty period, which have been notified to the reseller or verified by 3TEMP (warrantor) or a representative of the warrantor, and which concern design, manufacturing or material defects and consequential damages occurring on the product itself.
Page 39
Rev.100318-01-v1 3TEMP can not accept any responsibility for possible errors in catalogues, brochures and other printed material provided that such alterations can be made without sub sequential changes being necessary in specifications 3TEMP/PLAE2TECH. All rights reserved 2019 Hipster 1grp...
Page 40
‘‘The details create the big picture’’ Web: 3temp.com Mail: 3TEMP Magasinsgatan 3 67131 Arvika Email: [email protected]...