Sealey WPS225P Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,

and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR

PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

Refer to

Instruction

Manual

1. SAFETY

1.1.

ELECTRICAL SAFETY

WARNING! It is the user's responsibility to check the following:

‰

Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and

all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical

products. You may obtain an RCD by contacting your local Sealey dealer.

If the pump is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable Appliance

Test) tested.

Electrical safety information, it is important that the following information is read and understood.

1.2.

Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.

1.3.

Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.

1.4.

Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the

correct fuse - see fuse rating in these instructions.

DO NOT pull or carry the appliance by the power cable.

8

DO NOT pull the plug from the socket by the cable.

8

DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or

8

replaced immediately by a qualified electrician.

1.5.

This product is fitted with a BS1363/A 13 Amp 3 pin plug.

If the cable or plug is damaged during use, switch the electricity supply and remove from use.

Ensure that repairs are carried out by a qualified electrician.

Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.

a) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.

b) Connect the BROWN live wire to the live terminal 'L'.

c) Connect the BLUE neutral wire to the neutral terminal 'N'.

Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.

Sealey recommend that repairs are carried out by a qualified electrician.

1.6.

GENERAL SAFETY

WARNING! Pump must be used in accordance with Health & Safety, government, local authority, and water authority rules and

‰

regulations.

Familiarise yourself with application and limitations, as well as the specific potential hazards peculiar to the pump.

9

WARNING! Disconnect the pump from the mains power before changing accessories, servicing or performing any maintenance.

‰

Maintain the pump in good condition (use an authorised service agent). Keep the pump clean.

9

Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.

9

If the bottom of the water container is covered with sludge, sand, gravel or mud etc, suspend the pump or place it on a raised base to

9

operate above the solid matter. Sand and such substances will reduce working life of pump, and invalidate your warranty.

In swimming pools, fish ponds, etc, ensure location is clear of people and animals, including removal of fish from pond.

9

Note: this pump is not designed for continuous use in a fish pond or similar water feature or display.

DO NOT operate the pump if any parts are damaged or missing as this may cause failure and/or possible personal injury.

8

DO NOT use the pump for any purpose other than for that which it is designed.

8

DO NOT use to pump, chemicals, fuels, salt water, explosive, corrosive, inflammable or health-hazardous substances, dangerous liquids

8

or faecal matter.

DO NOT insert hands into the mouth of the pump as this could lead to injury.

8

DO NOT use to pump septic tanks or settling pits. DO NOT pump any liquids other than water.

8

DO NOT use with liquids containing abrasive materials (e.g. sand) or containing mixtures of dirt, sand, mud or clay.

8

DO NOT operate the pump out of water. The pump pick up area must be completely submerged during operation.

8

DO NOT exceed the maximum submersible depth - see specifications.

8

DO NOT operate the pump during freezing temperatures. DO NOT leave the pump in water that may freeze.

8

DO NOT pump liquids over 35°C in temperature.

8

DO NOT use for pumping sea water or inflammable, corrosive, explosive or dangerous liquids.

8

DO NOT carry the pump by its electrical cable, or outlet pipe. Use the handle only.

8

DO NOT touch the mains plug with wet hands.

8

DO NOT kink, crush, drag or drive over the mains cable and protect it from sharp edges oil and heat.

8

© Jack Sealey Limited

INSTRUCTIONS FOR

SUBMERSIBLE STAINLESS WATER PUMP

AUTOMATIC 225LTR/MIN

WPS225P

MODEL NO:

Original Language Version

Recommended fuse rating

13 Amp

WPS225P| Issue 1 11/12/15