Related Manuals for Sony SNC-WL862
Summary of Contents for Sony SNC-WL862
- Page 1 D-963-100-12 (1) Network Camera Installation Manual Before operating the unit, please read this manual thoroughly and retain it for future reference. SNC-WL862 © 2019 Sony Corporation...
-
Page 2: Table Of Contents
Table of Contents About the Manuals About the Manuals ............2 Safety Regulations (supplied) Location and Function of Part ........3 The Safety Regulations describes the secure usage Preparations ..............5 of camera. Be sure to read it. Check the serial number ....... 5 Connect cable .......... -
Page 3: Location And Function Of Part
Inner View Location and Function of Part Outer View The figure shows the camera without the dome cover. Lens (sensor) module 3-axis adjustable Slide track microSD card slot This slot is used for separately sold microSD Microphone memory cards. - Page 4 NETWORK indicator I/O combo cable The indicator lights up or flashes when the camera is connected to the network. The indicator is off when the camera is not connected to the network. Cable gland for Ethernet Cable gland for I/O combo cable Note Take care not to trap the cables between the camera and the ceiling or the wall.
-
Page 5: Preparations
Remove the waterproof connectors. Preparations If you do not need to route I/O wires, leave the plastic cap in place. If you need to connect I/O wires, keep the stainless nut. Check the serial number Write down the serial number and MAC address on the camera label for later reference. - Page 6 Route cables through the holes. Hook up the tether wire between the camera Route cables through the routing holes, and and the top mounting plate. secure the top mounting plate to ceiling by driving the included screws. Pass the Ethernet cable through the components of the waterproof cable gland.
- Page 7 Tighten and install the components of the Connect the I/O combo cable on the outside of waterproof connector. the cameras. Note Protect against moisture by using putties. Pass the I/O combo cable (if applied) through the routing hole, and attach a rubber seal ring. Install the combo cable with the white headers inside the camera, and tighten the stainless hex nut from the inside of the camera.
-
Page 8: Installing A Microsd Card
• If you attach the camera to the ceiling, check Installing a microSD card periodically, at least once a year, to ensure that the connection has not loosened. If conditions Gently insert the memory card into the slot until it warrant, make this periodic check more clicks into place as required. -
Page 9: Installing The Dome Cover
Installing the Dome Cover Replace the 2 desiccant bags on the sides of the camera. They remove the moisture in the dome. Replace the desiccant every time you open the dome cover. Notes • Distortion other than the specified optical area of the dome cover also may be appear on the images depending on zooming, tilting or rotation. -
Page 10: Important Precautions
Note Make sure the safety tether wire for the dome cover does not get caught between the dome cover and camera unit. Important precautions • Despite the fact that this unit is rated IP66, this section includes important precautions to prevent any malfunction caused by condensation and/or water ingress. -
Page 11: Connecting To The I/O Combo Cable
Connecting to the I/O combo cable Dry contact with external DC power source to supply a relay. Dry contact is the safest connection to protect devices. Dry contact Switch Photo Coupler External DC power External AC Power with Protected Earth DC 0V Relay External Device... - Page 12 The +5V pin provides a 5V output voltage, and the max. load is 50mA. The max. voltage for DO pins is 30V DC (External power). In order to control AC devices, the Wet contact diagram can be taken in consideration. The diagram uses a relay to control the ON/OFF condition of the AC device.
-
Page 13: Connection
• Do not connect the power input cable if power is supplied by a PoE system. SNC toolbox stands for Sony Network Camera • The ambient temperature must be -30ºC or toolbox. higher at startup of the camera. -
Page 14: Specifications
Specifications Item Description Camera Image Sensor 1/2.8" Progressive CMOS sensor Number of Image Sensor Number of Effective Pixels Approx. 5.16 megapixels x4 Minimum Illumination (50 IRE) 0.15 lux (F1.9 1/30s) Number of Horizontal Viewing 88.8° to 40.2° Angle Number of Vertical Viewing Angle 59.8° to 28.6° Focal Length f = 3.7 to 7.7 mm F-Number... - Page 15 It may appear flawless, but the components may have deteriorated over time, which may cause a malfunction or accident. For details, please consult the store of purchase or an authorized Sony dealer. Caution The Network Camera is to be connected only to PoE networks without routing to the outside plant.