Table of Contents
Quick Links
Model
Power source
Input power (IEC)
Mains lead length
Radius of operation
Net weight
Dimensions (L×W×H)
Attachments:
Dusting brush
Crevice nozzle
Extension wand
Mini turbine nozzle
Attachment holder
Specifications are subject to change Without notice for further improvement
MC-E4111-KP47
MC-E4113-KP47
Destination : Europe
MC-E4111
230-240V
50Hz
1500-1600W
6.7m
7m
6.6kg
330×320×1100
*
*
*
-
-
© 2006 Matsushita Electric Industrial Co., Ltd. All
rights
distribution is a violation of law.
ORDER NO ECD0602001C2
Vacuum Cleaner
MC-E4113
230-240V
50Hz
1500-1600W
6.7m
7m
6.6kg
330×320×1100
*
*
*
*
*
reserved.
Unauthorized
copying
and
Table of Contents
Related Manuals for Panasonic MC-E4111-KP47
Summary of Contents for Panasonic MC-E4111-KP47
- Page 1 ORDER NO ECD0602001C2 Vacuum Cleaner MC-E4111-KP47 MC-E4113-KP47 Destination : Europe Model MC-E4111 MC-E4113 Power source 230-240V 230-240V 50Hz 50Hz Input power (IEC) 1500-1600W 1500-1600W Mains lead length 6.7m 6.7m Radius of operation Net weight 6.6kg 6.6kg Dimensions (L×W×H) 330×320×1100 330×320×1100...
-
Page 2: Replacement Of Main Parts
MC-E4111-KP47 / MC-E4113-KP47 3.2. BELT (Beater bar belt) 3 REPLACEMENT OF MAIN PARTS 1. Remove the base plate and motor shaft belt as explained previously in paragraph 3.1 Motor shaft belt, point 1-2. IMPORTANT: Before replacing part always 2. Lift the beater bar assembly and remove the belt from the DISCONNECT THE CLEANER FROM THE ELECTRIClTY beater bar pulley and motor pulley. - Page 3 MC-E4111-KP47 / MC-E4113-KP47 3.3. BEATER BAR ASSEMBLY 3.4. MOTOR PULLEY UNlT 1. Remove the base plate as explained previously in 1. Remove the base plate as explained previously in paragraph 3.1 Motor shaft belt, point 1. paragraph 3.1 Motor shaft belt, point 1.
- Page 4 MC-E4111-KP47 / MC-E4113-KP47 3.5. MOTOR 5. Remove the motor. Then, remove the two lead wires with a 1. Remove base plate, pedal and motor pulley as explained quick-connect terminal from the carbon brush holder tabs. previously in paragraph 3.4 Motor pulley unit, points 1-4.
-
Page 5: Carbon Brush
MC-E4111-KP47 / MC-E4113-KP47 3.6. CARBON BRUSH 4. Replace the carbon brush holder with new one and insert NOTE: Replace both carbon brushes at the same time. into the motor. (Fig.14) 1. Remove motor case unit and take out the motor as explained previously in paragraph 3.5 Motor, points 1-4. - Page 6 MC-E4111-KP47 / MC-E4113-KP47 3. Remove the lead wire (white) connector from the printed 2. Remove the two screws fixing the printed circuit board circuit board section. (Fig.16) holder to separate the printed circuit board holder A from the printed circuit board holder that covers the printed circuit board.
- Page 7 MC-E4111-KP47 / MC-E4113-KP47 3.9. MAIN FUSE 3.10. ON/OFF SWlTCH 1. Remove the three screws fixing the front body to remove it. 1. Remove hose end and front body as explained previously in (Fig. 19) paragraph 3.8 MAIN FUSE. * Point: Lift the front body from below the main unit.
-
Page 8: Troubleshooting Guide
MC-E4111-KP47 / MC-E4113-KP47 8 TROUBLE SHOOTING GUIDE CONDITlON CHECK POINT METHOD OF INSPECTlON CAUSE/REMEDY Motor fails to rotate. Plug (fuse-1ink) Check fuse continuity. lf there is no continuity, replace it. (no noise is heard at all). (UK, lRLonly) Main fuse Check main fuse continuity. - Page 9 MC-E4111-KP47 / MC-E4113-KP47 9 PACKING INSTRUCTIONS and ATTACHMENTS MC-E4111 / /MC-E4113...
-
Page 10: Packing List
MC-E4111-KP47 / MC-E4113-KP47 10 PACKING LIST safety Ref. No. Part No. Part Name & Description Remarks AMC61Z-ZG0KE Individual carton MC-E4111 AMC61Z-ZH0KE Individual carton MC-E4113 AMC87J-XD00E Cushion A unit AMC0TZ-XD00E Cushion C AMC75Z-XD00E Cushion plate AMC72Z-XD00E Cushion plate A AMC46Z-XD00E Partition board...