Table of Contents
16 | nVent.com
4.3.4 "POINT SETUP..." Sub-Menu
The "Point Setup" sub-menu is used to configure parameters that relate directly to each
specific control Point (A or B). Note that these settings must be configured for each of the
control points that are in use.
Included in this menu are control mode settings, circuit breaker and switch ratings, auto-cycle
set up parameters, etc..
CONTROL SETPOINT
LO TS 1
LO LOAD
HI GFI
GFI TRIP
TS ALARMS CONFIG...
OTHER ALARMS CONFIG...
POINT SETUP...
COMMON SETUP...
COMMUNICATIONS SETUP...
--- END ---
Point Setup Sub-Menu
TAG
SWITCH CONTROL MODE = {PROPORTIONAL, PROP AMB.
DEADBAND
PROP BAND
CYCLE TIME
SWITCH RATING
CIRCUIT BREAKER
MAX POWER
3 PH PWR CALC
TS FAIL MODE
TS CTL MODE
TS 1 TYPE
TS 1 LEAD RESIST
TS 1 HI LIMIT
TS 2 TYPE
TS 2 LEAD RESIST
TS 2 HI LIMIT
VOLT SOURCE
FIXED VOLT
VOLT TURNS RATIO
CURRENT TURNS RATIO
AUTO-CYCLE
AUTO-CYCLE INTERVAL
AUTO-CYCLE UNITS
OVERRIDE SOURCE
LOAD SHEDDING
--- END ---
Table 4.7
=
20°C
=
-10°C
=
1.0 A
=
50 mA
=
75 mA
= {19 ALPHA-NUMERIC
CHARACTERS}
SSR, DEADBAND, or PROP AMB.
CONTACTOR}
= {1 to 50}°C
= {1 to 50}°C
= {10 to 255}MIN
= {0.3 to 100.0} A
= {0.3 to 100.0} A
= {3 W to 33,000} W
= {YES or NO}
= {OFF or ON}
= {TS 1.FAIL OFF(ON) or
TS 1-FAIL TO TS 2 or
TS 2-FAIL OFF(ON) or
TS 2-FAIL TO TS 1 or
AVERAGE-FAIL OFF(ON) or
AVERAGE-FAIL TO GOOD or
LOWEST-FAIL OFF(ON) or
LOWEST-FAIL TO GOOD or
EXT.INPUT-FAIL OFF(ON)or
EXT.INPUT-FAIL TO TS 1 or
EXT.INPUT-FAIL TO TS 2}
= {100 ( PLAT or NI-FE}
= {0 to 20.00} Ω
= {ENA or DIS}
= {100 ( PLAT or NI-FE}
= {0 to 20.00} Ω
= {ENA or DIS}
= {PT. A or PT. B or FIXED}
= = {0 to 1000} V
= {0.10 to 9.90} TO 1
= {0.10 to 60.00} TO 1
= {ENA or DIS}
= {1 to 240}
= {HOURS or MINUTES}
= {REMOTE or EXT. INPUT}
= {ENA or DIS}
=
(only if SWITCH CONTROL
MODE is DEADBAND or
point A and EXT. OUTPUT =
INHIBIT)
(only if SWITCH CONTROL
MODE is not DEADBAND)
(only if SWITCH CONTROL
MODE is PROP AMB.
CONTACTOR)
(only if SSR is being used)
(only if SSR is being used)
(only if SSR is being used)
(only if TS 1 TYPE = NI-FE)
(only if TS 2 TYPE = NI-FE)
(only if VOLT SOURCE
= FIXED)
(only if VOLT SOURCE =
current point°s voltage)
(only if AUTO-CYCLE = ENA)
(only if AUTO-CYCLE = ENA)
Hide quick links:
Table of Contents
