Quick Links
Installation Instructions for the
SS431P Hall Effect Sensor
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or
emergency stop devices, or in any other
application where failure of the product could
result in personal injury.
Failure to comply with these instructions could
result in death or serious injury.
SOLDERING/ASSEMBLY
Leads must be adequately supported during any
forming/ shearing operation to ensure that the leads
are not stressed inside the plastic case. Recom-
mended PC board wave soldering temperature is
o
o
250 to 260
C (482 to 500
maximum.
OPERATING CHARACTERISTICS
Supply voltage
I
Operate
CC
I
Released
CC
I
Ratio (Op/Rel)
CC
Output switching time
Rise, 10 to 90%
Fall, 90 to 10%
Operating Temperature
MAGNETIC SPECIFICATIONS
Temperature Range
Max. Operate Gauss
Min. Release Gauss
Min. Differential Gauss
HONEYWELL Sensing and Control
F) for 3 seconds
Min.
25°C
Target
3.8
11
15
4
6
2.0
2.5
30 µs
30 µs
-55 to +160°C (-67 to +320°F)
-40°C
0°C
25°C
70
65
60
-70
-65
-60
15
15
15
ABSOLUTE MAXIMUM RATINGS*
Supply voltage
Voltage externally
applied to output
Output ON current
Storage Temperature
Magnetic flux
*Absolute maximum ratings are the extreme limits that
the device will withstand without damage to the device.
However, the electrical and mechanical characteristics
are not guaranteed as the maximum limits (above
recommended operating conditions) are approached, nor
will the device necessarily operate at absolute maximum
ratings.
NOTICE
Interruption of power to a bipolar or latching
device may cause the output to change state when
power is restored. If a magnetic field of sufficient
strength is present, the sensor output will be in the
condition dictated by the magnetic field.
NOTE: The SS431P is a 2-wire, current output
sensor.
Max.
Remarks
24
VDC
20
mA
9
mA
4.0
mA
= 300 Ω,
V
= 12 V. R
CC
L
C
= 33 nF, C
= 330 pF
L
S
85°C
125°C
60
65
-60
-65
12
12
ISSUE 1
PK 80076
-1 to +30 VDC
+30 VDC max. (OFF only)
-0.5 VDC min. (OFF or ON)
50 mA max.
-65 to +160°C (-85 to +320°F)
No limit. Circuit cannot be
damaged by magnetic
overdrive.
150°C
70
-70
10
Related Manuals for Honeywell SS431P
Summary of Contents for Honeywell SS431P
- Page 1 PC board wave soldering temperature is condition dictated by the magnetic field. 250 to 260 C (482 to 500 F) for 3 seconds maximum. NOTE: The SS431P is a 2-wire, current output sensor. OPERATING CHARACTERISTICS Min. 25°C Max. Remarks Target ...
-
Page 2: Block Diagram
SS431P Hall Effect Sensor PK 80076 ISSUE 1 BLOCK DIAGRAM GAUSS VS. TEMPERATURE 2 Honeywell • Sensing and Control For application help: call 1-800-537-6945... - Page 3 3. Part dimensions do not include flash. Flash is limited to .005” max. 4. Lead dimension refers to location of lead centerlines as they exit the plastic package. Honeywell • Sensing and Control 3 For application help: call 1-800-537-6945...
- Page 4 SS431P Hall Effect Sensor PK 80076 ISSUE 1 WARRANTY/REMEDY Honeywell warrants goods of its manufacture as being free of defective materials and faulty workmanship. Contact your local sales office for warranty information. If warranted goods are returned to Honeywell during the period of coverage, Honeywell will repair or replace without charge those items it finds defective.
- Page 5 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Honeywell SS431P...