Page 1
Switch Configuration Guide for Dell PS Series SANs Abstract This document illustrates how to configure Dell EMC™ Networking S4048-ON switches for use with Dell™ PS Series storage while using Dell EMC best practices. February 2018 Dell EMC Configuration and Deployment Guide...
Update to include configuration steps for both OS 9.x and 10.x The information in this publication is provided “as is.” Dell Inc. makes no representations or warranties of any kind with respect to the information in this publication, and specifically disclaims implied warranties of merchantability or fitness for a particular purpose.
2.3.1 Disable DCB ..............................13 2.3.2 Remove DCB policies and apply standard flow control ................... 14 2.3.3 Revert to default VLAN ID on switch and arrays ....................14 Dell EMC Networking S4048-ON Switch Configuration Guide for Dell PS Series SANs | SCG1026...
Page 4
3.2.1 Disable iSCSI ..............................22 3.2.2 Disable 802.3x flowcontrol on all ports ......................22 3.2.3 Enable DCB ..............................22 3.2.4 Create tagged VLAN for all ports and port-channels ..................23 Dell EMC Networking S4048-ON Switch Configuration Guide for Dell PS Series SANs | SCG1026...
Page 5
3.3.9 Reload ................................29 3.3.10 Verify DCB status ............................29 3.3.11 Configure additional switch .......................... 29 Technical support and resources ..........................30 Related resources ............................30 Dell EMC Networking S4048-ON Switch Configuration Guide for Dell PS Series SANs | SCG1026...
Introduction Introduction This document illustrates how to configure Dell EMC™ Networking S4048-ON switches for use with Dell™ PS Series storage while using Dell EMC best practices. The recommended configuration uses Link Aggregation Groups (LAGs) for inter-switch connections. The host servers and storage controllers can be connected to the switches using the 40GbE Quad Small Form-factor Pluggable (QSFP) ports with appropriate breakout cables.
Introduction Cabling diagram The cabling diagram in Figure 1 represents the Dell EMC recommended method for deploying servers and PS Series arrays. Cabling diagram Dell EMC Networking S4048-ON Switch Configuration Guide for Dell PS Series SANs | SCG1026...
Note: Firmware downloads and documentation can be found at Dell.com/support. Dell EMC recommended switch configuration The steps in this section show how to configure two S4048-ON switches with a Link Aggregation Group (LAG). The switches are interconnected using two of the 40GbE Quad Small Form-factor Pluggable (QSFP) uplink ports, and the LAG is configured for Dynamic Link Aggregation Control Protocol (LACP).
The prior example assumes a class C subnet mask. 2.1.5 Configure login credentials Dell(conf)#username admin privilege 15 password 0 Dell(conf)#enable password level 15 0 Dell EMC Networking S4048-ON Switch Configuration Guide for Dell PS Series SANs | SCG1026...
Dell(conf)# protocol spanning-tree rstp Dell(conf-rstp)#no disable Dell(conf-rstp)#exit 2.1.10 Configure port channel for LAG Configure the switch interconnect as a LAG. Dell(conf)#interface Port-channel 1 Dell(conf-if-po-1)#mtu 12000 Dell(conf-if-po-1)#switchport Dell(conf-if-po-1)#no shutdown Dell(conf-if-po-1)#exit Dell EMC Networking S4048-ON Switch Configuration Guide for Dell PS Series SANs | SCG1026...
Note: The preceding procedure places all switch ports in the default VLAN. If you prefer to place ports in a non-default VLAN, refer to the documentation for your switch. Dell EMC Networking S4048-ON Switch Configuration Guide for Dell PS Series SANs | SCG1026...
Switch configuration (OS 9.x) Configure Data Center Bridging (DCB) (optional) Use the following commands to enable DCB mode on the switch. Note: You must complete the Dell EMC recommended switch configuration steps in section 2.1 before configuring the switch for DCB mode. 2.2.1 Disable 802.3x flowcontrol on SFP+ ports...
Power off all arrays and hosts connected to the SAN before proceeding with these steps. 2.3.1 Disable DCB Dell#configure Dell(conf)#no dcb enable Dell(conf)#exit Dell EMC Networking S4048-ON Switch Configuration Guide for Dell PS Series SANs | SCG1026...
Verify DCB status Dell#show dcb DCB Status : Disabled 2.3.7 Configure additional switch Repeat the commands from section 2.3 to disable DCB on any additional switches. Dell EMC Networking S4048-ON Switch Configuration Guide for Dell PS Series SANs | SCG1026...
Dell#delete startup-config Proceed to delete startup-config [confirm yes/no]yes Dell#reload System configuration has been modified. Save? [yes/no]no Proceed with reload [confirm yes/no]yes Note: The switch will reboot. Dell EMC Networking S4048-ON Switch Configuration Guide for Dell PS Series SANs | SCG1026...
is the gateway for the switch. If your management system is on the same subnet as the switch, the previous step may be omitted. The prior example assumes a class C subnet mask. Dell EMC Networking S4048-ON Switch Configuration Guide for Dell PS Series SANs | SCG1026...
Note: The preceding procedure places all switch ports in the default VLAN. If you prefer to place ports in a non-default VLAN, refer to the switch documentation. Dell EMC Networking S4048-ON Switch Configuration Guide for Dell PS Series SANs | SCG1026...
Switch configuration (OS 10.x) This section provides steps to configure Dell EMC Networking S4048-ON switches running Dell Networking OS 10.x (firmware 10.x). If your switches are running Dell Networking OS 9.x (firmware 9.x), follow the steps in section 2 instead.
To configure these ports as 4 x 10GbE ports, use the following commands. OS10(config)# interface breakout 1/1/ map 10g-4x OS10(config)# exit OS10# Use the following command to check port interface status. OS10# show interface status Dell EMC Networking S4048-ON Switch Configuration Guide for Dell PS Series SANs | SCG1026...
This section describes enabling iSCSI auto-detection of attached storage arrays and switch auto- configuration. PS Series and Dell EMC SC Series storage arrays will be detected by the switch when iscsi is enabled. The switch will auto-configure for Jumbo frames with MTU 9216 and flowcontrol receive on, transmit off for all the ports.
OS10(config)# interface range ethernet 1/1/49,1/1/50 OS10(conf-range-eth1/1/49,1/1/50)# no switchport OS10(conf-range-eth1/1/49,1/1/50)# channel-group 1 mode active OS10(conf-range-eth1/1/49,1/1/50)# mtu 9216 OS10(conf-range-eth1/1/49,1/1/50)# flowcontrol receive on OS10(conf-range-eth1/1/49,1/1/50)# flowcontrol transmit off OS10(conf-range-eth1/1/49,1/1/50)# exit OS10(config)# exit Dell EMC Networking S4048-ON Switch Configuration Guide for Dell PS Series SANs | SCG1026...
VLAN, refer to the switch documentation. Configure Data Center Bridging (DCB) (optional) To enable DCB mode on the switch, use the following commands. Note: You must complete the Dell EMC recommended switch configuration steps in section 3.1 before configuring the switch for DCB mode. 3.2.1...
OS10(config-pmap-network-qos)# exit OS10(config)# OS10(config)# policy-map type application OS10(config-pmap-application)# class class-iscsi OS10 (config-pmap-c-app)# set qos-group 4 OS10 (config-pmap-c-app)# set cos 4 OS10 (config-pmap-c-app)# exit OS10(config-pmap-application)# exit OS10(config)# Dell EMC Networking S4048-ON Switch Configuration Guide for Dell PS Series SANs | SCG1026...
The previous steps in section 3.3.3 and 3.3.4, revert the switch ports to default native vlan 1. Use the following command to remove VLANs other than vlan 1 from the switch configuration. OS10(config)# no interface vlan Dell EMC Networking S4048-ON Switch Configuration Guide for Dell PS Series SANs | SCG1026...
Verify DCB status OS10# show lldp dcbx interface ethernet 1/1/ 3.3.11 Configure additional switch Repeat the commands from section 3.3 to disable DCB on any additional switches. Dell EMC Networking S4048-ON Switch Configuration Guide for Dell PS Series SANs | SCG1026...
Dell EMC Storage Compatibility Matrix For PS Series best practices white papers, reference architectures, and sizing guidelines for enterprise applications and SANs, refer to PS Series Technical Documents. Dell EMC Networking S4048-ON Switch Configuration Guide for Dell PS Series SANs | SCG1026...