Tts bluetooth-hands free with phonebook (24 pages)
Summary of Contents for B-Speech B-Speech Prim
Page 1
Original instructions ® AVANTI FALL PROTECTION SYSTEM User’s, Installation and Maintenance Manual Runner 2000/2002 & Eagle Runner MASTER 47840008 EN_CORREGIDO.indd 1 25/10/17 12:01...
Page 2
AVANTI Fall Protection System User‘s Manual and Installation Instructions Only trained people may use this fall protection system. This manual must be available to staff at all times during installation, maintenance and operation. Additional copies are available from the manufacturer upon request.
Page 3
Index 1. Limited Warranty........6 1.1 Terms and definitions .
Page 4
CE certificate of AVANTI Fall Protection System with Runner 2000/2002: MASTER 47840008 EN_CORREGIDO.indd 4 25/10/17 12:01...
Page 5
CE certificate of AVANTI Fall Protection System with Eagle Runner: MASTER 47840008 EN_CORREGIDO.indd 5 25/10/17 12:01...
1 Limited Warranty Avanti Wind Systems A/S warrants that commencing from the AND WARRANTIES, INCLUDING, BUT NOT LIMITED TO, ANY date of shipment to the Customer, and continuing for a period of IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY, the longer of 365 days thereafter, or the period set forth in the FITNESS FOR A PARTICULAR PURPOSE, NON-INFRINGE- standard Avanti warranty, the Fall Protection System (“Product”) MENT, SATISFACTORY QUALITY, COURSE OF DEALING,...
2 Caution a) The AVANTI Fall Protection System (hereafter named as FPS) shall The maximum number of multiple users in the ladder system is 3. only be operated by users trained in daily inspection, use and work at The fall arrester must be attached to no more than one personal fall- heights.
ah) The combination of FPS parts in anyway other than the intended b) Before starting to climb, the user clicks the runner on the safety rail and will jeopardize safety. Thus, the FPS parts shall not be combined in checks its locking. anyway other than the intended.
3.4 Marking Upward direction when mounted onto rail Read instructions before use Read instructions before use 4 Installation Runner production no. Runner production no. Runner production no. Runner production no. EEC-notifi ed body no. EEC-notifi ed body no. EEC-notifi ed body no. EEC-notifi ed body no.
A rung fi tting mounted on the rail Hammerhead bolt with self-locking nut i. For each rail section, mount a rung fi tting on the fi rst (lowest) rung of the ladder. ii. For each rail section, mount a rung fi tting on the last (highest) rung of the ladder.
Use the supplied self-locking nuts at all times. k) Ensure that each screw extends from the nut by at least half of the thread diameter, or by at least 2 threads (apply the most restrictive requirement). A rail-stop shall be installed at the top and bottom of the rail, and at any STOP 55mm ≤...
Do not use the FPS if it looks defective or if parts are missing. STOP If the FPS has blocked a fall or has been put out of service because of doubts, it may only be put back to service after an inspection by a certified technician is performed.
b) Open the runner by pressing the left bottom pin and pulling apart both 7.1.2 Releasing the Runner 2000/2002 from the safety rail body sides of the runner simultaneously. a) Before stepping in or stepping off the ladder, attach alternative c) While lifting the lever, tilt the runner so the runner is parallel and close to fall protection.
Page 14
b) Open the runner by pressing e) Push together the two body the right button and pulling apart parts of the runner until the both body sides of the runner push button pops out and you simultaneously. hear a click. c) Place the runner on the safety rail ensuring that the arrow on the plate of the runner points upwards.
7.2.2 Releasing the Eagle Runner from the safety rail 8 Maintenance a) Pull out the plunger and rotate the lever downwards to the horizontal position (see images below). 8.1 Cautions a) Keep all the parts free of oil, grease, paint, aggressive chemicals and alike.
8.4.2 Ladder stiles 8.4.7 Circular inspection sticker a) Ensure that no dents, holes, or cracks have any influence on the stiles´ a) Ensure that the sticker is present and that the due date has not stability. expired. b) The dents shall not exceed 20mm in diameter or be more than 1 mm deep.