Page 1 User Manual Original Instructions Stratix Managed Switches Stratix 5400 Switches (1783-HMS) Stratix 5410 Switches (1783-IMS) Stratix 5700 Switches (1783-BMS) ArmorStratix 5700 Switches (1783-ZMS) Stratix 8000 and 8300 Switches (1783-MS, 1783-RMS, 1783-MX)
Page 2: Important User Information
Important User Information Read this document and the documents listed in the additional resources section about installation, configuration, and operation of this equipment before you install, configure, operate, or maintain this product. Users are required to familiarize themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws, and standards.
Page 3: Table Of Contents
Stratix 5400 Templates ........25...
Page 4 Chapter 3 Install Stratix 5400 Switches Specifications ..........75 Overview .
Page 5 Table of Contents Install an SFP Module ........120 Remove an SFP Module from an SFP Slot .
Page 6 DHCP for Ring Devices ........222 Multiple Rings (Stratix 5400 Switches) ..... 225 Configure DLR via Device Manager .
Page 7 Table of Contents Configure NAT via Device Manager ..... . . 262 Configure NAT via the Logix Designer Application ..274 Configure NAT via the Logix Designer Application (Stratix 5410 Switches) .
Page 8 Table of Contents Smartports........... 350 Custom Smartport Roles .
Page 9 Stratix 5400 Data Types ........
Page 10 Port Numbering Stratix 5400 Port Numbering ....... . . 496 Stratix 5410 Port Numbering .
Page 11 Table of Contents Index ............541 Rockwell Automation Publication 1783-UM007G-EN-P - February 2017...
Page 12 Table of Contents Notes: Rockwell Automation Publication 1783-UM007G-EN-P - February 2017...
Page 13: Preface
You can view or download publications at http://www.rockwellautomation.com/global/literature-library/overview.page. To order paper copies of technical documentation, contact your local Allen-Bradley distributor or Rockwell Automation sales representative. For information on additional software features or further configuration, see Cisco publications for Industrial Ethernet series switches at http://www.Cisco.com.
Page 14 Preface Notes: Rockwell Automation Publication 1783-UM007G-EN-P - February 2017...
Page 15: Summary Of Changes
Summary of Changes This manual contains new and updated information as indicated in the following table. Topic Page Stratix 8300 switches support Multi-mode Express Setup 21, 30 Rockwell Automation Publication 1783-UM007G-EN-P - February 2017...
Page 16 Summary of Changes Notes: Rockwell Automation Publication 1783-UM007G-EN-P - February 2017...
Page 17: About The Switches
Chapter About the Switches Topic Page EtherNet/IP CIP Interface Lite Versus Full Firmware Features (Stratix 5700 Switches) Software Features Hardware Features Memory Allocation Stratix® managed switches provide a secure switching infrastructure for harsh environments. You can connect the switches to network devices such as servers, routers, and other switches.
Page 18 About the Switches Table 1 - Stratix Switches Switch Family Description Stratix 5400 switches Layer 2 and Layer 3 scalable managed switches. Available in 8…20 port versions, including all Gigabit port versions. Stratix 5410 switches Layer 2 and Layer 3 scalable managed switches.
Page 19: Ethernet/Ip Cip Interface
About the Switches Chapter 1 EtherNet/IP CIP Interface Stratix switches contain an EtherNet/IP network interface. The EtherNet/IP network is an industrial automation network specification from the Open DeviceNet Vendor Association (ODVA). The network uses the Common Industrial Protocol (CIP) for its application layer and TCP/UDP/IP for its transport and network layers.
Page 20: Lite Versus Full Firmware Features (Stratix 5700 Switches)
Chapter 1 About the Switches Lite Versus Full Some features for Stratix 5700 switches depend on whether the switches have Full or Lite firmware. All Stratix 8000 and ArmorStratix 5700 switches have Firmware Features Full firmware. (Stratix 5700 Switches) To determine the firmware type available for specific catalog numbers, see the Stratix 5700 switch descriptions in Table 166 on page 505.
Page 21: Software Features
• DHCP for Ring Devices Stratix 5400 switches Stratix 5700 switches ArmorStratix 5700 switches Enhanced Interior Gateway Routing Stratix 5400 switches with Layer 3 firmware • — Protocol (EIGRP) Stratix 5410 switches with Layer 3 firmware Stratix 8300 base units EtherChannels •...
Page 22: Hardware Features
• • Hardware Features See the following for a description of hardware features: • For Stratix 5400, Stratix 5700, ArmorStratix 5700, and Stratix 8000/ 8300 switches, see Table 3 on page • For Stratix 5410 switches, see Table 4 on page •...
Page 23 To configure, monitor, and manage a switch, you can connect a switch to a computer through the console port: • Stratix 5400 and Stratix 5700 switches—Connect to the console port with an RJ45-to-DB-9 adapter cable or a mini USB cable. The mini USB driver is available in the firmware download section at http://www.rockwellautomation.com.
Page 24 Chapter 1 About the Switches Table 4 - Hardware Features for Stratix 5410 Switches Feature Description Dual power supply modules Depending on the switch model, one AC or DC power supply module comes pre-installed in the switch. You can order an optional second power supply of any voltage type to provide redundancy and additional power for PoE devices: •...
Page 25: Memory Allocation
Layer 2 firmware models have the IPv4 Default template. Layer 3 firmware models have these templates: • IPv4 Default • Dual IPv4/IPv6 Default • IPv4 Routing • Dual IPv4/IPv6 Routing Table 5 - Stratix 5400 Templates Feature Memory Allocation IPv4 Default Dual IPv4/IPv6 IPv4 Routing...
Page 26: Stratix 5410 Templates
Chapter 1 About the Switches Stratix 5410 Templates The selected template optimizes the resources in the switch to support features for eight routed interfaces and 1024 VLANs. Layer 2 firmware models have the Default template. Table 6 - Stratix 5410 Layer 2 Firmware Model Template Feature Memory Allocation Unicast MAC addresses...
Page 27: Stratix 5700 And Armorstratix 5700 Templates
About the Switches Chapter 1 Stratix 5700 and ArmorStratix 5700 Templates The following SDM templates are available: • Default • Lanbase Routing • Dual IPv4 and IPv6 If you enable static routing, or if you have more than 180 IGMP groups or multicast routes., consider using the routing template.
Page 28: Stratix 8000 And 8300 Templates
Chapter 1 About the Switches Stratix 8000 and 8300 Templates The following SDM templates are recommended: • Default • Lanbase Routing For static and connected routing, or if you have more than 180 IGMP groups or multicast routes, you can use the Lanbase Routing template. Other SDM templates are available, but are not covered in detail.
Page 29: Get Started
Chapter Get Started Topic Page Express Setup Overview Multi-mode Express Setup Single-mode Express Setup Configure Network Settings via Device Manager Configure Network Settings via the Logix Designer Application Default Global Macro RSLinx Software and Network Who Support Configuration via Device Manager Configuration via the Studio 5000 Environment User Administration via Device Manager Configuration Files...
Page 30: Express Setup Overview
Chapter 2 Get Started Express Setup Overview When you first install the switch, use Express Setup to perform these initial setup tasks: • Assign the switch an initial IP address. You can then access the switch through the IP address for more configuration. •...
Page 31 Short Press mode) catalog number 1585D-M4TBJM-2 For 1783-BMS4S2SGL or 1783-BMS4S2SGA switches, you also need a Gigabit copper SFP module, such as Allen-Bradley catalog number 1783-SFP1GSX, or a Gigabit fiber-to-Ethernet media converter. Before you begin, do the following: • Single-mode Express Setup or multi-mode Express Setup in Short Press mode: –...
Page 32: Express Setup Button
WARNING: When you press the Express Setup button while power is on, an electrical arc can occur. This could cause an explosion in hazardous location installations. Stratix 5400 Switch Express Setup Button Stratix 5410 Switch Express Setup Button...
Page 33 Get Started Chapter 2 Stratix 5700 Switch Express Setup Button ArmorStratix 5700 Switch Express Setup Button Stratix 8000/8300 Switch Express Setup Button Rockwell Automation Publication 1783-UM007G-EN-P - February 2017...
Page 34: Multi-Mode Express Setup
Chapter 2 Get Started Multi-mode Express Setup Multi-mode Express Setup has three modes: IMPORTANT The Studio 5000 Logix Designer® application supports only Medium-press mode. • Short Press mode—You want to use Express Setup to enter the initial IP address of the switch. You can then configure additional network settings via Device Manager.
Page 35: Run Multi-Mode Express Setup In Short Press Mode
Get Started Chapter 2 Run Multi-mode Express Setup in Short Press Mode Be aware of the following conditions that cause the switch to exit Short Press mode. Condition Status Indicator Behavior A non-default configuration exists on the switch. The Setup status indicator turns red for 10 seconds. You do not connect to the Express Setup port within 2 The unconnected port status indicator and the Setup minutes from when the port status indicator flashes...
Page 36: Run Multi-Mode Express Setup In Medium Press Mode
Chapter 2 Get Started 4. Connect a Category 5 Ethernet cable from the flashing switch port to the Ethernet port on a computer. For 1783-BMS4S2SGL or 1783-BMS4S2SGA switches, do one of the following: • Insert a copper SFP module into the Gi1/1 port on the switch. Then connect a Category 5 Ethernet cable from the SFP module to the Ethernet port on the computer.
Page 37: Run Multi-Mode Express Setup In Long Press Mode
Get Started Chapter 2 To run multi-mode Express Setup in Medium Press mode, follow these steps. 1. Apply power to the switch. When the switch powers on, it begins its power-on sequence. The power-on sequence can take as many as 90 seconds to complete. 2.
Page 38: Single-Mode Express Setup
Chapter 2 Get Started Single-mode Express Setup To run single-mode Express Setup, follow these steps. 1. Make sure that at least one switch Ethernet port is available for Express Setup. 2. Apply power to the switch. When the switch powers on, it begins its power-on sequence. The power-on sequence can take up to 90 seconds to complete.
Page 39: Configure Network Settings Via Device Manager
Get Started Chapter 2 Configure Network Settings To configure network settings via Device Manager after you run Express Setup, follow these steps. via Device Manager 1. Access Device Manager, as described on page If the Express Setup window does not appear, try the following: •...
Page 40 Chapter 2 Get Started Table 11 - Express Setup Fields Field Description Network Settings Host Name The name of the device. Management Interface (VLAN ID) The name and ID of the management VLAN through which the switch is managed. The management VLAN is the broadcast domain through which management traffic is sent between specific users or devices.
Page 41 • For a statically assigned IP address, change it to the previously configured IP address. 6. For Stratix 5400 and Stratix 5410 switches, synchronize the SD card that came with the switch with the internal memory of the switch: • To synchronize the SD card via Device Manager, see page •...
Page 42: Configure Network Settings Via The Logix Designer Application
Chapter 2 Get Started Configure Network Settings To configure network settings via the Logix Designer Application after running multi-mode Express Setup in Medium Press mode, follow these steps. via the Logix Designer Application 1. If you have not yet added the switch to a controller project, complete Steps 1…3 page...
Page 43 IMPORTANT For 1783-BMS4S2SGL or 1783-BMS4S2SGA switches, make sure that DC power is disconnected before disconnecting Ethernet cables. 8. For Stratix 5400 and Stratix 5410 switches, synchronize the SD card that came with the switch with the internal memory of the switch, as...
Page 44: Default Global Macro
Chapter 2 Get Started Default Global Macro Once you complete Express Setup, the switch runs a default global macro (ab-global). This macro configures the switch for industrial automation applications that use the EtherNet/IP protocol. This macro sets many parameters, including these major settings: •...
Page 45: Data Accessible With Cip
Get Started Chapter 2 EDS files for the Stratix switches are included with the following software packages: • RSLinx software • RSLogix 5000® software • RSNetWorx for EtherNet/IP software You can also obtain the EDS files in either of these two ways: •...
Page 46 Chapter 2 Get Started Table 12 - Data Accessible with CIP (continued) Data Type Details Other status data • Module identification (vendor ID, device type, product code, product name, revision, serial number) • Major/minor fault status, I/O connection, module identity match •...
Page 47: Configuration Via Device Manager
Get Started Chapter 2 Configuration via Device Manager is a web-based management tool for configuring, monitoring, and troubleshooting individual switches. You can display Device Manager Device Manager from anywhere in your network through a web browser. Device Manager displays real-time views of switch configuration and performance.
Page 48: Access Device Manager
Chapter 2 Get Started Access Device Manager With IOS version 15.2(5)EA.fc4 and later, Device Manager provides a secure connection via the latest version of Internet Explorer or Firefox. Security messages from your browser can appear when you access Device Manager. To make sure that Device Manager runs properly, disable any pop-up blockers or proxy settings in your browser and any wireless clients on your computer.
Page 49 Get Started Chapter 2 c. Click Confirm Security Exception. Rockwell Automation Publication 1783-UM007G-EN-P - February 2017...
Page 50 Chapter 2 Get Started 3. On the Device Manager Login window, enter the switch name and password. Rockwell Automation Publication 1783-UM007G-EN-P - February 2017...
Page 51: Configure Port Settings
Get Started Chapter 2 Configure Port Settings The basic port settings determine how data is received and sent between the switch and the attached device. You can change these settings to fit your network needs and to troubleshoot network problems. The settings on a switch port must be compatible with the port settings of the connected device.
Page 52 Chapter 2 Get Started Table 15 - Port Settings Field Description Port Name The number of the switch port, including port type, such as Fa for Fast Ethernet and Gi for Gigabit Ethernet, and the specific port number: • Gi/1 is the gigabit port 1 of the switch. •...
Page 53: Configuration Via The Studio 5000 Environment
Get Started Chapter 2 Configuration via the You can manage the switch by using the Logix Designer application in the Studio 5000® environment. The Logix Designer application is IEC 61131-3 Studio 5000 Environment compliant and offers relay ladder, Structured Text, function block diagram, and sequential function chart editors for you to develop application programs.
Page 54 Chapter 2 Get Started 3. On the Select Module Type dialog box, select the switch and click Create. If you do not see the switch on the list, you can obtain the AOP from the Rockwell Automation support website: http://www.rockwellautomation.com/support/ Rockwell Automation Publication 1783-UM007G-EN-P - February 2017...
Page 55: General Properties
Get Started Chapter 2 General Properties To configure general properties, follow these steps. 1. In the navigation pane, click General and complete the fields. IMPORTANT Make sure that the IP address and host name match the values you used during Express Setup. On the Module Properties dialog box, you can choose either an IP address or host name.
Page 56 Chapter 2 Get Started 2. In the Module Definition area, click Change. 3. On the Module Definition dialog box, complete the fields and click Field Description Revision The major and minor revision of the switch: • Major revision: 1…128 • Minor revision: 1…255 Electronic Keying Choose one of the following: •...
Page 57: Connection Properties
Get Started Chapter 2 Connection Properties In the navigation pane, click Connection. Table 17 - Connection Fields Field Description Requested Packet Interval (RPI) Enter a value between 300…5000. Inhibit Module Check to disable communication between the controller and the switch. Clear the checkbox to restore communication.
Page 58: Switch Configuration
Chapter 2 Get Started Switch Configuration You can configure IP settings and administrative parameters. The IP address can be manually assigned (static) or it can be automatically assigned by a Dynamic Host Configuration Protocol (DHCP) server. The default is Static. We recommend that you choose Static and manually assign the IP address for the switch.
Page 59: Port Configuration
Get Started Chapter 2 Port Configuration Port settings determine how data is received and sent between the switch and the attached device. In the navigation pane, click Port Configuration. Table 19 - Port Configuration Fields Field Description Unit Indicates where the port resides: (Stratix 8000/8300 switches) •...
Page 60 Chapter 2 Get Started Table 19 - Port Configuration Fields (continued) Field Description Auto-negotiate If you want the port and end-device to auto-negotiate the link speed and Duplex mode, check the checkbox. To specify the desired port speed and Duplex mode manually, clear the checkbox. We recommend that you use the default (auto-negotiate) so that the speed and duplex settings on the switch port automatically match the setting on the connected device.
Page 61: User Administration Via Device Manager
Get Started Chapter 2 User Administration via You can add, modify, or delete users and user login information for the switch via Device Manager. Device Manager From the Admin menu, choose Users. For each user, you can specify the information in Table Table 20 - Add User Fields Field...
Page 62: Configuration Files
Chapter 2 Get Started Configuration Files The switch configuration files (config.text and vlan.dat) are in ASCII human-readable format. This configuration file is stored in nonvolatile memory and is read into the Random Access Memory (RAM) of the switch as the running configuration when the switch is powered up. When any changes are made to the configuration, the changes immediately take effect in the running configuration.
Page 63: Manage Configuration Files Via The Logix Designer Application
Get Started Chapter 2 Manage Configuration Files via the Logix Designer Application You can do the following: • Save the switch configuration to a file for archiving • Restore a switch configuration that is stored locally on the computer or within the Logix Designer application project.
Page 64: Secure Digital (Sd) Card
SD card. You must use the 1784-SD1 card available from Rockwell Automation with the switches. • Stratix 5400 and Stratix 5410 switches ship with an SD card, which stores the initial configuration and firmware for the switches. ATTENTION: If a non-Rockwell SD card is used in Stratix switches, Rockwell Automation reserves the right to withhold support.
Page 65: Synchronize The Sd Card Via Device Manager
Get Started Chapter 2 ATTENTION: SD cards commonly have a physical read-only lock switch. If this switch is engaged, the switch starts from the SD card successfully. Changes that are made by using the CLI, AOP, or Device Manager take effect, but are not saved when the switch is restarted.
Page 66 Chapter 2 Get Started Table 21 - Manual Sync Tab Fields Field Description SD Card Status Indicates whether SD card is present, the status of the card, and from where its configuration was started. SD to Flash Sync Choose from these options: •...
Page 67: Synchronize The Sd Card Via The Logix Designer Application
Get Started Chapter 2 Synchronize the SD Card via the Logix Designer Application You can synchronize the SD card to either the configuration file or the entire image. In the navigation pane, click SD Flash Sync. Table 23 - SD Flash Sync Fields Field Description SD Flash Status...
Page 68: Compactflash Memory Card (Stratix 8000/8300 Switches)
Chapter 2 Get Started CompactFlash Memory Card The CompactFlash card for Stratix 8000/8300 switches contains the switch IOS operating system, Device Manager firmware, and user-defined (Stratix 8000/8300 Switches) configuration settings. Without the CompactFlash card, the switch cannot power up or restart. If you remove the card with the switch running, the switch continues to function.
Page 69: Cisco Network Assistant
Get Started Chapter 2 With firmware revision 2.001 or later, the firmware is installed to the running nonvolatile memory location: • If you start the switch with the SD card inserted, the firmware is installed on the SD card. • If you start the switch from internal memory without the SD card inserted, the firmware is installed in the internal memory.
Page 70: Command-Line Interface
• To connect to the standard 9-pin serial port on a computer, use a RJ45-to-DB-9 adapter cable (not supplied with the switch). • (Stratix 5400, Stratix 5410, Stratix 5700, and ArmorStratix 5700 switches). Use a standard mini-USB cable to connect to the mini- USB port on a computer.
Page 71 Chapter Install Stratix 5400 Switches Topic Page Specifications Overview Parts List and Required Tools Install or Remove the SD Card Verify Switch Operation Mount the Switch on a DIN Rail Remove the Switch from the DIN Rail Ground the Switch...
Page 72: Install Stratix 5400 Switches
Chapter 3 Install Stratix 5400 Switches ATTENTION: Environment and Enclosure This equipment is intended for use in a Pollution Degree 2 industrial environment, in overvoltage Category II applications (as defined in IEC 60664-1), at altitudes up to 2000 m (6562 ft) without derating.
Page 73: Chapter 3
Install Stratix 5400 Switches Chapter 3 WARNING: When you connect or disconnect the Power or Alarm Removable Terminal Blocks (RTBs) with field side power applied, an electrical arc can occur. This could cause an explosion in hazardous location installations. Be sure that power is removed or the area is nonhazardous before proceeding.
Page 74: Chapter 3
Chapter 3 Install Stratix 5400 Switches ATTENTION: Prevent Electrostatic Discharge This equipment is sensitive to electrostatic discharge, which can cause internal damage and affect normal operation. Follow these guidelines when you handle this equipment: • Touch a grounded object to discharge potential static.
Page 75: Specifications
Install Stratix 5400 Switches Chapter 3 Specifications For additional specifications and certifications, see the Stratix Ethernet Device Specifications Technical Data, publication 1783-TD001. Attribute 1783-HMS8T4CGN, 1783-HMS16T4CGN, 1783-HMS4C4CGN, 1783-HMS4S8E4CGN, 1783-HMS8S4CGN, 1783-HMS8SG4CGN, 1783-HMS8TG4CGN, 1783-HMS8TG4CGR, 1783-HMS8TG8EG4CGN, 1783-HMS4SG8EG4CGN, 1783-HMS8SG4CGR 1783-HMS4T4E4CGN 1783-HMS4EG8CGN, 1783-HMS4EG8CGR, 1783-HMS8TG8EG4CGR, 1783-HMS4SG8EG4CGR, 1783-HMS16TG4CGN, 1783-HMS16TG4CGR Power supply 12…54V DC, 3.7 A max...
Page 76: Parts List And Required Tools
Chapter 3 Install Stratix 5400 Switches Follow these steps to install the switch. 1. (Optional) Install or remove the SD card. 2. Verify switch operation. 3. Mount the switch on a DIN rail. 4. Ground the switch. 5. Wire the DC power source for the switch and attach the switch power connectors.
Page 77 Install Stratix 5400 Switches Chapter 3 Obtain these tools: • Ratcheting torque screwdriver that exerts up to 1.69 N m (15 in lbs) of • • pressure • Small, flat-blade screwdriver  • #6 ring terminal lug for 5.3 mm (10 AWG) wire, such as Thomas &...
Page 78: Install Or Remove The Sd Card
Install Stratix 5400 Switches Install or Remove the SD Card A secure digital (SD) card ships with the Stratix 5400 switch. The SD card contains the switch firmware and initial configuration. You can order a replacement SD card from Rockwell Automation, catalog number 1784-SD1, if needed.
Page 79: Verify Switch Operation
Install Stratix 5400 Switches Chapter 3 Verify Switch Operation Before installing the switch in its final location, power on the switch, and verify that the switch powers up. The time that is required for the switch to start up is directly related to your switch configuration.
Page 80: Mount The Switch On A Din Rail
Chapter 3 Install Stratix 5400 Switches Mount the Switch The switch ships with a spring-loaded latch on the rear panel for mounting on a DIN rail. on a DIN Rail ATTENTION: To prevent the switch from overheating, observe these minimum clearances: •...
Page 81: Remove The Switch From The Din Rail
Install Stratix 5400 Switches Chapter 3 Remove the Switch To remove the switch from a DIN rail or a rack, follow these steps. from the DIN Rail 1. Remove power from the switch, and disconnect all cables and connectors from the front panel of the switch.
Page 82 Chapter 3 Install Stratix 5400 Switches To ground the switch to earth ground, follow these steps. Be sure to follow any grounding requirements at your site. 1. Use a Phillips screwdriver or a ratcheting torque screwdriver with a Phillips head to remove the ground screw from the front panel of the switch.
Page 83: Wire The Switch Dc Power Source
For switches with Power over Ethernet (PoE) capability, PoE power is drawn from the single power connection. There is no separate power input for PoE. DC Power Source Switch Configuration Required Voltage Input Power Supplied per Port Allen-Bradley Products 44-54V 15.4 W, max Switched-mode power supplies:...
Page 84 Chapter 3 Install Stratix 5400 Switches 6. Insert the exposed part of the positive wire into the connection labeled DC+ and the exposed part of the return wire into the connection labeled DC-. Be sure that you cannot see any wire lead. Only wire with insulation can extend from the connector.
Page 85: Attach The Switch Power Connectors
Install Stratix 5400 Switches Chapter 3 9. Connect the other end of the return wire to the return terminal on the DC power source. When you are testing the switch, one power connection is sufficient. If you are installing the switch and are using a second power source, repeat this procedure with the second power connector.
Page 86 Chapter 3 Install Stratix 5400 Switches 2. Use a ratcheting torque flathead screwdriver to tighten the captive screws on the sides of the power connectors. 32514-M When you test the switch, one power source is sufficient. If you install the switch and use a second power source, repeat this procedure for the second power connector (Pwr B), which installs just below the primary power connector (Pwr A).
Page 87: Install An Sfp Module
Install Stratix 5400 Switches Chapter 3 Install an SFP Module WARNING: When you insert or remove the small form-factor pluggable (SFP) optical transceiver while power is on, an electrical arc can occur. This could cause an explosion in hazardous location installations.
Page 88 Chapter 3 Install Stratix 5400 Switches To insert an SFP module into the SFP slot, follow these steps. 1. Attach an ESD-preventive wriststrap to your wrist and to a grounded bare metal surface. 2. Grasp both sides of the SFP module and align the module sideways in front of the slot opening.
Page 89: Remove An Sfp Module From An Sfp Slot
Install Stratix 5400 Switches Chapter 3 Remove an SFP Module To remove an SFP module from an SFP slot, follow these steps. from an SFP Slot 1. Attach an ESD-preventive wriststrap to your wrist and to a grounded bare metal surface.
Page 90: Wire The External Alarms
Chapter 3 Install Stratix 5400 Switches Wire the External Alarms The switch has two alarm inputs and one Form C (single-pole, double-throw) alarm output relay circuits for external alarms. The input alarm relay circuits are designed to sense if the alarm input is open or closed relative to the alarm input reference pin.
Page 91 Install Stratix 5400 Switches Chapter 3 The labels for the alarm relay connector are on the switch panel. Table 24 - Alarm Relay Connector Labels Label Connection Alarm Output Normally Open (NO) connection Alarm Output Common connection Alarm Output Normally Closed (NC) connection...
Page 92 Chapter 3 Install Stratix 5400 Switches 5. Use a ratcheting torque flathead screwdriver to torque the captive screw of the alarm relay connector to 0.23 N•m (2.0 lb•in). Do not exceed the recommended torque. REF - External Device Connection 2...
Page 93: Attach The Alarm Relay Connector To The Switch
Install Stratix 5400 Switches Chapter 3 Attach the Alarm Relay To attach the alarm relay connector to the front panel of the switch, follow these steps. Connector to the Switch 1. Insert the alarm relay connector into the receptacle on the switch front panel.
Page 94: Connect To 10Base-T, 100Base-Tx, Or 1000Base-T Ports
Chapter 3 Install Stratix 5400 Switches Connect to 10BASE-T, To connect to 10BASE-T, 100BASE-TX, or 1000BASE-T ports, follow these steps. 100BASE-TX, or 1000BASE-T Ports ATTENTION: To prevent electrostatic-discharge (ESD) damage, follow recommended board and component handling procedures. 1. Choose one of these options to connect a device: •...
Page 95: Connect To Poe Ports
Install Stratix 5400 Switches Chapter 3 Connect to PoE Ports Switches with PoE ports require a separate power supply. For power supply requirements based on your application, refer to page 1. Insert a straight-through, twisted four-pair, Category 5e or better cable with an RJ45 connector into the PoE port.
Page 96: Connect To A Dual-Purpose Port
Chapter 3 Install Stratix 5400 Switches Connect to a A dual-purpose port is one port with two interfaces, one for an RJ45 cable and another for an approved SFP module. Only one interface can be active at a Dual-purpose Port time.
Page 97: Install Stratix 5410 Switches
Chapter Install Stratix 5410 Switches Topic Page Switch Specifications Power Supply Specifications Overview Parts List and Required Tools Install or Remove the SD Card Verify Switch Operation Mount the Switch on a Rack Mount the Switch on a Wall Ground the Switch Install a Power Supply Module in the Switch Wire the Power Source Remove a Power Supply Module from the Switch...
Page 98 Chapter 4 Install Stratix 5410 Switches North American Hazardous Location Approval The following information applies when operating this equipment in Informations sur l’utilisation de cet équipement en environnements hazardous locations. dangereux. Products marked "CL I, DIV 2, GP A, B, C, D" are suitable for use in Class I Division 2 Groups Les produits marqués "CL I, DIV 2, GP A, B, C, D"...
Page 99: Chapter 4
Install Stratix 5410 Switches Chapter 4 WARNING: Special Conditions for Safe Use • This equipment shall be mounted in an ATEX Zone 2 certified enclosure with a minimum ingress protection rating of at least IP54 (as defined in EN 60529) and used in an environment of not more than Pollution Degree 2 (as defined in EN 60664-1) when applied in Zone 2 environments.
Page 100: Chapter 4
Chapter 4 Install Stratix 5410 Switches ATTENTION: Prevent Electrostatic Discharge This equipment is sensitive to electrostatic discharge, which can cause internal damage and affect normal operation. Follow these guidelines when you handle this equipment: • Touch a grounded object to discharge potential static. •...
Page 101: Switch Specifications
Install Stratix 5410 Switches Chapter 4 ATTENTION: Use only a soft dry anti-static cloth to wipe down equipment. Do not use any cleaning agents. ATTENTION: Electrical Safety Considerations (Switches with DC power supply modules) To comply with the CE Low Voltage Directive (LVD), all connections to this equipment must be powered from a source compliant with the following: •...
Page 102: Overview
Chapter 4 Install Stratix 5410 Switches Overview When determining where to place the switch, observe these guidelines: • Airflow around the switch is unrestricted. To prevent the switch from overheating, observe these minimum clearances: – Top and bottom: 44.45 mm (1.75 in.) –...
Page 103: Parts List And Required Tools
Install Stratix 5410 Switches Chapter 4 Follow these steps to install the switch. 1. (Optional) Install or remove the SD card. 2. Verify switch operation. 3. Mount the switch on a rack. Mount the switch on a wall. 4. Ground the switch. 5.
Page 104 Chapter 4 Install Stratix 5410 Switches Obtain these tools: • Ring, spade, or flanged spade terminal (terminals should be insulated) – Ring terminal (such as Tyco part number 2-34158-1 for 16…14 AWG or 2-34852-1 for 12…10 AWG wire) – Spade terminal (such as Tyco part number 54367-2 for 16…14 AWG wire) –...
Page 105: Install Or Remove The Sd Card
Install Stratix 5410 Switches Chapter 4 Install or Remove the SD Card A Secure Digital (SD) card ships with the Stratix 5410 switch. The SD card contains the switch firmware and initial configuration. You can order a replacement SD card from Rockwell Automation, catalog number 1784-SD1, if needed.
Page 106 Chapter 4 Install Stratix 5410 Switches 3. Install or remove the card. To install the card, slide it into the slot, and press it firmly in place until it latches in the spring loaded mechanism. The card is keyed so that you cannot fully insert it the wrong way.
Page 107: Verify Switch Operation
Install Stratix 5410 Switches Chapter 4 Verify Switch Operation Before installing the switch in its final location, power on the switch, and verify that the switch powers up. The time that is required for the switch to start up is directly related to your switch configuration.
Page 108: Attach Brackets
Chapter 4 Install Stratix 5410 Switches Attach Brackets To attach brackets on the switch, follow this procedure. 1. Identify a mount position and attach brackets to both sides of the switch. Cable-side Mount Position 32573-M Center Mount Position 32574-M Power-supply Mount Position 32575-M Rockwell Automation Publication 1783-UM007G-EN-P - February 2017...
Page 109 Install Stratix 5410 Switches Chapter 4 2. Insert the rubber plugs in the unused holes on both sides of the switch. 32572-M 3. Use a screwdriver or pen to push in the rubber plugs completely. 32571-M Rockwell Automation Publication 1783-UM007G-EN-P - February 2017...
Page 110: Mount The Switch
Chapter 4 Install Stratix 5410 Switches Mount the Switch After you attach the brackets on the switch, use the four supplied number-12 Phillips machine screws to attach the brackets to the rack. Cable-side Mount Position 32576-M Center Mount Position 32577-M Power-supply Mount Position 32578-M Rockwell Automation Publication 1783-UM007G-EN-P - February 2017...
Page 111: Mount The Switch On A Wall
Install Stratix 5410 Switches Chapter 4 Mount the Switch on a Wall To mount the switch on a wall, see the following: • Attach the Brackets on page 111 • Mount the Switch on page 113 IMPORTANT To mount the switch on a wall in an enclosure, follow these minimum clearances: •...
Page 112 Chapter 4 Install Stratix 5410 Switches 2. Insert the rubber plugs in the unused holes on both sides of the switch. 32572-M 3. Use a screwdriver or pen to push in the rubber plugs completely. 32571-M Rockwell Automation Publication 1783-UM007G-EN-P - February 2017...
Page 113: Mount The Switch
Install Stratix 5410 Switches Chapter 4 Mount the Switch The switch can be mounted on a wall in only one position: the side panel must face up, and the port side must face left. For the best support of the switch and cables, make sure that the switch is attached securely to wall studs or to a firmly attached plywood backboard.
Page 114: Ground The Switch
Chapter 4 Install Stratix 5410 Switches Ground the Switch To ground the switch, follow these steps. Be sure to follow any grounding requirements at your site. 1. To remove the ground screw from the cable side of the switch, use a Phillips screwdriver or a ratcheting torque screwdriver with a Phillips head.
Page 115: Install A Power Supply Module In The Switch
Install Stratix 5410 Switches Chapter 4 Install a Power Supply The switch ships with one pre-installed power supply. To install a second power supply, follow these steps. Module in the Switch WARNING: If you connect or disconnect wiring while the field-side power is on, an electrical arc can occur.
Page 116: Wire The Power Source
Chapter 4 Install Stratix 5410 Switches 3. Insert the power supply module into the slot, and gently push it in. When inserted correctly, the power-supply module is flush with the switch. 32557-M 4. Use a ratcheting torque screwdriver to torque each screw to 0.904…1.13 N•m (8…10 lb•in).
Page 117 Install Stratix 5410 Switches Chapter 4 3. Open the cover. ANA .Tim eCo de Con sole 32559-M The terminal screws labels are on the power-input terminal cover. Line connection for high-voltage AC (PSU1) Line connection for high-voltage AC (for PSU2) Neutral connection for high-voltage AC (PSU1) Neutral connection for high-voltage AC (PSU2) Positive connection for high-voltage DC (PSU1)
Page 118 Chapter 4 Install Stratix 5410 Switches 5. Strip each of the two wires to 6.3 mm (0.25 in.) ± 0.5 mm (0.02 in.). Do not strip more than 6.8 mm (0.27 in.) of insulation from the wire. Stripping more than the recommended amount of wire can leave exposed wire from the connector after installation.
Page 119 Install Stratix 5410 Switches Chapter 4 • For DC power, connect the positive wire into the terminal screw that is labeled +, and the negative wire into the terminal screw labeled -. For low-voltage DC power, connect the wires to the terminals labeled For high-voltage DC power, connect the wires to the terminals labeled Hi.
Page 120: Remove A Power Supply Module From The Switch
Chapter 4 Install Stratix 5410 Switches Remove a Power Supply By removing the power-supply modules, you can power off the switch without disconnecting the wiring from the power-input terminal. Module from the Switch To remove a power supply module from the switch, follow these steps. 1.
Page 121: Rockwell Automation Publication 1783-Um007G-En-P - February
Install Stratix 5410 Switches Chapter 4 SFP modules are inserted into SFP module slots on the front of the switch. These field-replaceable modules provide the uplink optical interfaces, send (TX) and receive (RX). You can use any combination of compatible SFP modules: •...
Page 122: Remove An Sfp Module From An Sfp Slot
Chapter 4 Install Stratix 5410 Switches 6. For fiber-optic SFP modules, remove the dust plugs and save. ATTENTION: Do not remove the rubber plugs from the SFP module port or the rubber caps from the fiber-optic cable until you are ready to connect the cable.
Page 123: Wire The External Alarms
Install Stratix 5410 Switches Chapter 4 Wire the External Alarms The switch has four alarm inputs and one Form C (single-pole, double-throw) alarm output relay circuits for external alarms. The input alarm relay circuits are designed to sense if the alarm input is open or closed relative to the alarm input reference pin.
Page 124: Attach The Alarm Relay Connector To The Switch
Chapter 4 Install Stratix 5410 Switches Attach the Alarm Relay Insert the alarm relay RJ45 connector into the receptacle on the switch front panel. Connector to the Switch The 10/100/1000 ports on the switch automatically configure themselves to Connect to 10/100/1000 operate at the speed of attached devices.
Page 125 Install Stratix 5410 Switches Chapter 4 To connect a device to a 10/100/1000 Ethernet, PoE/PoE+ port, follow these steps. 1. Choose one of these options: • If the auto-MDIX feature is enabled, connect either a crossover or straight-through cable to an RJ45 connector on the front panel. The default setting for auto-MDIX is enabled.
Page 126: Connect To Sfp/Sfp+ Ports
Chapter 4 Install Stratix 5410 Switches Connect to SFP/SFP+ Ports To connect a fiber-optic cable to an SFP or SFP+ module, follow these steps. 1. Remove the rubber plugs from the module port and fiber-optic cable, and store them for future use. 2.
Page 127 Chapter Install Stratix 5700 Switches Topic Page Specifications Overview Parts List and Required Tools Install or Remove the SD Card Verify Switch Operation Mount the Switch on a DIN Rail Remove the Switch from the DIN Rail Ground the Switch Wire the Switch DC Power Source Attach the Switch Power Connectors Wire the Power over Ethernet DC Power Source...
Page 128: Install Stratix 5700 Switches
Chapter 5 Install Stratix 5700 Switches ATTENTION: Environment and Enclosure This equipment is intended for use in a Pollution Degree 2 industrial environment, in overvoltage Category II applications (as defined in IEC 60664-1), at altitudes up to 2000 m (6562 ft) without derating. This equipment is not intended for use in residential environments and may not provide adequate protection to radio communication services in such environments.
Page 129 Install Stratix 5700 Switches Chapter 5 European Hazardous Location Approval The following applies to products marked II 3 G: Such modules: • Are Equipment Group II, Equipment Category 3, and comply with the Essential Health and Safety Requirements relating to the design and construction of such equipment given in Annex II to Directive 94/9/EC.
Page 130: Specifications
Chapter 5 Install Stratix 5700 Switches Specifications For additional specifications and certifications, see the Stratix Ethernet Device Specifications Technical Data, publication 1783-TD001. Table 25 - Stratix 5700 Switches Attribute 1783-BMS4S2SGL, 1783-BMS4S2SGA, 1783-BMS06SL, 1783-BMS06SA, 1783-BMS20CL, 1783-BMS20CA, 1783-BMS20CGL, 1783-BMS20CGP, 1783-BMS06TL, 1783-BMS06TA, 1783-BMS06SGL, 1783-BMS06SGA, 1783-BMS20CGPK, 1783-BMS20CGN 1783-BMS06TGL, 1783-BMS06TGA, 1783-BMS10CL, 1783-BMS10CA, 1783-BMS10CGL, 1783-BMS10CGA,1783-BMS10CGP, 1783-BMS10CGN...
Page 131 Install Stratix 5700 Switches Chapter 5 • Temperature surrounding the unit does not exceed 60 °C (140 °F). IMPORTANT When the switch is installed in an industrial enclosure, the temperature within the enclosure is greater than normal room temperature outside the enclosure. The temperature inside the enclosure cannot exceed 140 °F (60 °C), the maximum ambient enclosure temperature of the switch.
Page 132: Parts List And Required Tools
Chapter 5 Install Stratix 5700 Switches Parts List and Required Tools Verify that you have these items. The PoE connector ships only with switch models with PoE ports. The connector is required only if you plan to use PoE. Stratix® 5700 switch Documentation PoE connector If needed, an SD card can be ordered separately from the switch.
Page 133: Install Or Remove The Sd Card
Install Stratix 5700 Switches Chapter 5 For simplified cabling, the automatic medium-dependent interface crossover (auto-MDIX) feature is enabled by default on the switch. With auto-MDIX enabled, the switch detects the required cable type for copper Ethernet connections and configures the interfaces accordingly. Therefore, you can use either a crossover or a straight-through cable for connections to a 10/100 or 10/100/1000 Ethernet switch port, regardless of the type of device on the other end of the connection.
Page 134: Verify Switch Operation
Chapter 5 Install Stratix 5700 Switches To remove the card, push it in and let it pop out via the spring-loaded mechanism. Grasp the card top and pull it out. Place it in an antistatic bag to protect it from static discharge. Al ar IN 1 IN 2...
Page 135: Mount The Switch On A Din Rail
Install Stratix 5700 Switches Chapter 5 3. After successfully running this test, do the following: a. Turn off power to the switch. b. Disconnect the cables. c. Decide where you want to install the switch The switch ships with a spring-loaded latch on the rear panel for mounting on Mount the Switch a DIN rail.
Page 136 Chapter 5 Install Stratix 5700 Switches ATTENTION: The console ports are intended for temporary local programming purposes only and not intended for permanent connection. The console port cables are not to exceed 3.0 m (9.84 ft) and must not contain hubs.
Page 137: Remove The Switch From The Din Rail
Install Stratix 5700 Switches Chapter 5 Remove the Switch To remove the switch from a DIN rail or a rack, follow these steps. from the DIN Rail 1. Remove power from the switch, and disconnect all cables and connectors from the front panel of the switch. 2.
Page 138 Chapter 5 Install Stratix 5700 Switches Use at least 4 mm (12 AWG) wire to connect to the external grounding screw. The ground lug is not supplied with the switch. You can use one of the these options: • Single ring terminal •...
Page 139: Wire The Switch Dc Power Source
Install Stratix 5700 Switches Chapter 5 5. Insert the ground screw into the functional ground screw opening on the front panel. Ring Terminal Lug (single lug shown) 32276-M 6. Use a ratcheting torque screwdriver to tighten the ground screws and ring terminal lugs to the switch front panel to 0.4 N m (3.5 lb in).
Page 140 Chapter 5 Install Stratix 5700 Switches 1. Locate the power connector. 32280-M 2. Identify the positive and return DC power connections. The positive DC power connection is labeled DC+, and the negative DC power connection is the adjacent connection labeled DC-. 3.
Page 141 Install Stratix 5700 Switches Chapter 5 Be sure that you cannot see any wire lead. Only wire with insulation can extend from the connector. ATTENTION: An exposed wire lead from a DC input power source can conduct harmful levels of electricity. Be sure that no exposed portion of the DC input power source wire extends from the connectors or terminal blocks.
Page 142 Chapter 5 Install Stratix 5700 Switches 8. Connect the other end of the positive wire to the positive terminal on the DC power source. 9. Connect the other end of the return wire to the return terminal on the DC power source. When you are testing the switch, one power connection is sufficient.
Page 143: Attach The Switch Power Connectors
Install Stratix 5700 Switches Chapter 5 Attach the Switch To attach the switch power connectors to the front panel of the switch, follow these steps. Power Connectors 1. Insert one power connector into the Pwr A receptacle on the switch front panel, and the other into the Pwr B receptacle.
Page 144: Wire The Power Over Ethernet Dc Power Source
The switch must be wired and grounded. Power input requirements depend on your application. Application Power Supply per Port Power Consumption Allen-Bradley Products PoE only 44…57V DC (48V DC nom) 15.4 W, max Switched mode power supplies: • 1606-XL Standard IEEE 802.3af...
Page 145: Attach The Poe Power Connector
Install Stratix 5700 Switches Chapter 5 4. Insert the exposed part of the positive wire into the DC+ connection and the exposed part of the return wire into the DC- connection. Make sure that you cannot see any wire lead. Only wire with insulation can extend from the connector.
Page 146: Install An Sfp Module
Chapter 5 Install Stratix 5700 Switches Install an SFP Module WARNING: When you insert or remove the small form-factor pluggable (SFP) optical transceiver while power is on, an electrical arc can occur. This could cause an explosion in hazardous location installations. Be sure that power is removed or the area is nonhazardous before proceeding.
Page 147 Install Stratix 5700 Switches Chapter 5 To insert an SFP module into an SFP slot, follow these steps. 1. Attach an ESD-preventive wriststrap to your wrist and to a grounded bare metal surface. 2. Grasp both sides of the SFP module and align the module sideways in front of the slot opening.
Page 148: Remove An Sfp Module From An Sfp Slot
Chapter 5 Install Stratix 5700 Switches Remove an SFP Module To remove an SFP module from an SFP slot, follow these steps. from an SFP Slot 1. Attach an ESD-preventive wriststrap to your wrist and to a grounded bare metal surface. 2.
Page 149: Wire The External Alarms
Install Stratix 5700 Switches Chapter 5 Wire the External Alarms The switch has two alarm inputs and one Form C (single-pole, double-throw) alarm output relay circuits for external alarms. The input alarm relay circuits are designed to sense if the alarm input is open or closed relative to the alarm input reference pin.
Page 150 Chapter 5 Install Stratix 5700 Switches The labels for the alarm relay connector are on the switch panel. Table 27 - Alarm Relay Connector Labels Label Connection Alarm Output Normally Open (NO) connection Alarm Output Common connection Alarm Output Normally Closed (NC) connection Alarm Input 2 Alarm Input Reference Ground connection Alarm Input 1...
Page 151 Install Stratix 5700 Switches Chapter 5 5. Use a ratcheting torque flathead screwdriver to torque the captive screw of the alarm relay connector to 0.23 N•m (2.0 lb•in). Do not exceed the recommended torque. REF - External Device Connection 2 IN1 - External Device Connection 1 32288-M 6.
Page 152: Attach The Alarm Relay Connector To The Switch
Chapter 5 Install Stratix 5700 Switches Attach the Alarm Relay To attach the alarm relay connector to the front panel of the switch, follow these steps. Connector to the Switch 1. Insert the alarm relay connector into the receptacle on the switch front panel.
Page 153: Connect To 10Base-T, 100Base-Tx, Or 1000Base-T Ports
Install Stratix 5700 Switches Chapter 5 Connect to 10BASE-T, To connect to 10BASE-T, 100BASE-TX, or 1000BASE-T ports, follow these steps. 100BASE-TX, or 1000BASE-T Ports ATTENTION: To prevent electrostatic-discharge (ESD) damage, follow recommended board and component handling procedures. 1. Choose one of these options to connect a device: •...
Page 154: Connect To Poe Ports
Chapter 5 Install Stratix 5700 Switches Connect to PoE Ports Switches with PoE ports require a separate power supply. For power supply requirements based on your application, refer to page 144. 1. Insert a straight-through, twisted four-pair, Category 5e or better cable with an RJ45 connector into the PoE port.
Page 155: Connect To A Dual-Purpose Port
Install Stratix 5700 Switches Chapter 5 4. Observe the port status indicator: • The status indicator turns amber while the SFP discovers the network topology and searches for loops. This process takes about 30 seconds, and then the port status indicator turns green. •...
Page 156 Chapter 5 Install Stratix 5700 Switches Notes: Rockwell Automation Publication 1783-UM007G-EN-P - February 2017...
Page 157: Install Stratix 8000 And 8300 Switches
Chapter Install Stratix 8000 and 8300 Switches Topic Page Specifications Overview Parts List and Required Tools Attach Expansion Modules Mount the Switch Install an SFP Module Ground the Switch Wire the DC Power Source for the Switch Wire the DC Power Source for the PoE Expansion Module Attach the Power and Relay Connector to the Switch to the Switch Attach the Power Connector to the PoE Expansion Module Wire External Alarms...
Page 158 Chapter 6 Install Stratix 8000 and 8300 Switches North American Hazardous Location Approval The following information applies when operating this equipment in Informations sur l’utilisation de cet équipement en environnements hazardous locations. dangereux. Products marked "CL I, DIV 2, GP A, B, C, D" are suitable for use in Class I Division 2 Groups Les produits marqués "CL I, DIV 2, GP A, B, C, D"...
Page 159: Specifications
Install Stratix 8000 and 8300 Switches Chapter 6 ATTENTION: To comply with the CE Low Voltage Directive (LVD), all connections to this equipment must be powered from a source compliant with safety extra low voltage (SELV) or protected extra low voltage (PELV). To comply with UL restrictions, all connections to this equipment must be powered from a source compliant with Class 2 or Limited Voltage/Current.
Page 160: Overview
Chapter 6 Install Stratix 8000 and 8300 Switches Overview When determining where to place the switch, observe these guidelines: • Operating environment is within the range specified in the technical specifications. See the Stratix Ethernet Managed Switches Technical Data, publication 1783-TD001. •...
Page 161 Install Stratix 8000 and 8300 Switches Chapter 6 8. Wire external alarms. 9. Connect to the switch ports: • 10/100 copper ports • PoE ports • Dual-purpose uplink (10/100/1000 and SFP fiber) ports • 100BaseFX 10. Install or remove the CompactFlash card. WARNING: If you connect or disconnect the communication cable with power applied to this module or any device on the network, an electrical arc can occur.
Page 162: Parts List And Required Tools
Chapter 6 Install Stratix 8000 and 8300 Switches Parts List and Required Tools Verify that you have these items. 31774-M Stratix® 8000/8300 switch Documentation Power and alarm relay connectors (qty. 2) Console cable If you plan to install a PoE expansion module, verify that you have a PoE power connector.
Page 163 Install Stratix 8000 and 8300 Switches Chapter 6 Obtain these tools: • Ratcheting torque screwdriver that exerts up to 1.69 N m (15 in lbs) of • • pressure  • #6 ring terminal lug for 5.3 mm (10 AWG) wire, such as Thomas & Bett part number 10RC6 or equivalent •...
Page 164: Attach Expansion Modules
Chapter 6 Install Stratix 8000 and 8300 Switches Attach Expansion Modules IMPORTANT If you are adding expansion modules, attach the expansion modules to the switch before mounting the switch. The switch can operate as a standalone device with two uplink ports and four or eight Fast Ethernet ports, or you can increase the number of Fast Ethernet ports by 8 or 16 by connecting expansion modules.
Page 165 Install Stratix 8000 and 8300 Switches Chapter 6 2. Remove the protective EMI-connector cover from the side panel. 31787-M 3. Push the upper module latches up and the lower module latches down. Then slide the switch and module together. The expansion module is shown with the side panel removed. Do not remove this panel unless you plan to install another module.
Page 166: Mount The Switch
Chapter 6 Install Stratix 8000 and 8300 Switches Mount the Switch You can mount the switch on one of the following: • DIN rail, as described on page 166 • Wall or panel, as described on page 168 IMPORTANT The switch must be mounted in an upright orientation, as shown in these instructions.
Page 167 Install Stratix 8000 and 8300 Switches Chapter 6 2. If you are using a heavy-duty 35 mm x 15 mm (1.38 in. x 0.59 in.) DIN rail, rotate all feet to the extended positions. Otherwise, if you are using 35 mm x 7.5 mm (1.38 in. x 0.30 in.) DIN rail, rotate the feet to the recessed positions.
Page 168: Mount The Switch On A Wall Or Panel
Chapter 6 Install Stratix 8000 and 8300 Switches Mount the Switch on a Wall or Panel To mount the switch on a wall or a panel, you need M5 or #10-24 or #10-32 bolts or screws with 1.27 cm (0.5 in.) O.D. flat washers. This hardware is not provided with the switch.
Page 169: Install An Sfp Module
Install Stratix 8000 and 8300 Switches Chapter 6 Install an SFP Module WARNING: When you insert or remove the small form-factor pluggable (SFP) optical transceiver while power is on, an electrical arc can occur. This could cause an explosion in hazardous location installations. Be sure that power is removed or the area is nonhazardous before proceeding.
Page 170 Chapter 6 Install Stratix 8000 and 8300 Switches To insert an SFP module into an SFP slot, follow these steps. 1. Attach an ESD-preventive wriststrap to your wrist and to a grounded bare metal surface. 2. Grasp both sides of the SFP module and align the module sideways in front of the slot opening.
Page 171: Ground The Switch
Install Stratix 8000 and 8300 Switches Chapter 6 Ground the Switch ATTENTION: For proper grounding, you must always connect the power supply functional-ground screw when connecting the power supply. You must provide an acceptable grounding path for each device in your application.
Page 172: Wire The Dc Power Source For The Switch
Chapter 6 Install Stratix 8000 and 8300 Switches 6. Insert the ground screw into the ground-screw opening on the front panel. 31791-M 7. Use a ratcheting torque screwdriver to tighten the ground screw and ring terminal lug to the switch front panel to 0.96 N•m (8.5 lb•in). 8.
Page 173 Install Stratix 8000 and 8300 Switches Chapter 6 3. Using an 18-gauge wire-stripping tool, strip each of the two wires to 6.3 mm (0.25 in.) ± 0.5 mm (0.02 in.). Do not strip more than 6.8 mm (0.27 in.) of insulation from the wire. Stripping more than the recommended amount of wire can leave exposed wire from the connector after installation.
Page 174: Wire The Dc Power Source For The Poe Expansion Module
Class 2 or Limited Voltage/Current. Power supply requirements for a PoE expansion module depend on your application. Application Power Consumption Power Supply per Port Allen-Bradley Products PoE only 44…57V DC (48V DC 15.4 W, max Switched mode power supplies: nom) •...
Page 175 Install Stratix 8000 and 8300 Switches Chapter 6 3. Use an 18-gauge wire-stripping tool to strip each of the two wires to 6.3 mm (0.25 in.) ± 0.5 mm (0.02 in.). Do not strip more than 6.8 mm (0.27 in.) of insulation from the wire. Stripping more than the recommended amount of wire can leave exposed wire from the connector after installation.
Page 176: Attach The Power And Relay Connector To The Switch
Chapter 6 Install Stratix 8000 and 8300 Switches Attach the Power and ATTENTION: The input voltage source of the alarm circuits must be an Relay Connector isolated source and limited to less than or equal to 24V DC, 1 A. to the Switch ATTENTION: Exposure to some chemicals can degrade the sealing properties of materials used in the relay.
Page 177 Install Stratix 8000 and 8300 Switches Chapter 6 Follow these steps to connect the DC power source and relay connector to the switch. 1. Insert the power and relay connector into the Pwr A receptacle on the switch front panel. 31786-M 2.
Page 178: Attach The Power Connector To The Poe Expansion Module
Chapter 6 Install Stratix 8000 and 8300 Switches Attach the Power Connector If you have a PoE expansion module, follow these steps to connect the DC power source to the PoE expansion module. to the PoE Expansion Module 1. Insert the power connector into the DC input terminal block on the PoE expansion module.
Page 179 Install Stratix 8000 and 8300 Switches Chapter 6 3. Insert the exposed wires for the external alarm device into the two connections labeled A, as shown in the following figure. External device, relay wire A connection 1 External device, relay wire A connection 2 4.
Page 180: Connect To 10/100 Copper Ports
Chapter 6 Install Stratix 8000 and 8300 Switches Connect to 10/100 1. Insert a straight-through, twisted four-pair, Category 5e or better cable with an RJ45 connector into the port. Copper Ports To 10/100 ports 31795-M 2. Insert the other cable end into an RJ45 connector on the other device. Connect to a PoE Two expansion modules provide PoE capability: Expansion Module Port...
Page 181: Connect To Dual-Purpose Uplink Ports
Install Stratix 8000 and 8300 Switches Chapter 6 Connect to Dual-purpose The switches have two dual-purpose uplink ports. Each dual-purpose uplink port has a 10/100/1000 RJ45 connector for a copper interface and a slot for an Uplink Ports SFP module. Only one port of the dual-purpose port can be active at a time. If an SFP module port is connected, the SFP module port has priority.
Page 182: Connect To 100Basefx Ports
Chapter 6 Install Stratix 8000 and 8300 Switches Connect to 100BaseFX Ports ATTENTION: Class 1 laser product. Laser radiation is present when the system is open and interlocks bypassed. Only trained and qualified personnel are allowed to install, replace, or service this equipment. 1.
Page 183: Configure Switch Features
Chapter Configure Switch Features Topic Page Access Control Lists (ACLs) Alarms CIP Sync Time Synchronization (Precision Time Protocol) Cryptographic IOS Device-level Ring (DLR) Dynamic Host Configuration Protocol (DHCP) Persistence EtherChannels Motion Prioritized QoS Macros Horizontal Stacking Internet Group Management Protocol (IGMP) Snooping with Querier Network Address Translation (NAT) Network Time Protocol (NTP) Parallel Redundancy Protocol (PRP)
Page 184: Access Control Lists (Acls)
Chapter 7 Configure Switch Features This chapter describes software features that you can configure via Device Manager, the Studio 5000 Logix Designer® application, or both. More software features are available. You can configure some features with the global macro or Smartports feature. For information about how to configure features not available in Device Manager or the Logix Designer application, see the documentation available at http://www.Cisco.com.
Page 185: Configure Acls Via Device Manager
Configure Switch Features Chapter 7 Configure ACLs via Device Manager The ACL window shows all existing standard and extended ACLs defined on the switch. Once you add an ACL to the ACL List tab, you can apply it to a port and specify a direction on the Apply ACL tab.
Page 186 Chapter 7 Configure Switch Features Create an ACL To create an ACL, follow these steps. 1. From the ACL window, click the ACL List tab. 2. Click Add, and then complete the fields in the header area. Field Description ACL Type Click Standard or Extended: •...
Page 187 Configure Switch Features Chapter 7 3. To define the ACL entry, click Add in the table area, and then complete the fields. Field Description Permit To permit traffic, check the checkbox. To deny traffic, clear the checkbox. An access list must contain at least one permit statement or all packets are denied entry into the network.
Page 188 Chapter 7 Configure Switch Features Apply an ACL You can apply inbound and outbound ACLs to ports: • Inbound ACLs can be applied to any port. • Outbound ACLs can be applied to only routed ports or ports assigned to an Access VLAN. You can configure these port settings in the Administrative Mode field on the Edit Physical Port window (Figure For more information about configuring port settings, see...
Page 189: Alarms
Configure Switch Features Chapter 7 2. Click the row for a port name. 3. In the Inbound ACL column, choose the ACL from the list of configured ACLs. 4. In the Outbound ACL column, choose ACL from the list of configured ACLs.
Page 190: Configure Alarms Via Device Manager
Chapter 7 Configure Switch Features Configure Alarms via Device Manager The switch software monitors conditions on a per port or a global basis. If the conditions do not match the set parameters, an alarm or a system message is triggered. By default, the switch sends the system messages to a logging facility. You can configure the switch to send SNMP traps to an SNMP server.
Page 191 Configure Switch Features Chapter 7 Global Alarms From the Configure menu, choose Alarm Settings and click the Global tab. Table 31 - Global Tab Fields Field Description FCS Hysteresis (1-10) The frame check sequence (FCS) error hysteresis threshold is used to determine when an alarm condition is cleared. This value is expressed as a percentage of fluctuation from the FCS bit error rate.
Page 192 Chapter 7 Configure Switch Features Port Alarms From the Configure menu, choose Alarm Settings and click the Port tab. For each port, choose an Alarm Profile and set the FCS threshold. The frame check sequence (FCS) error hysteresis threshold is expressed as a percentage of fluctuation from the FCS bit error rate.
Page 193 Configure Switch Features Chapter 7 On the Add/Edit Profile Instance window, you can configure the alarms and actions for an alarm profile. Table 32 - Add/Edit Profile Instance Fields Field Description Name A unique name for the alarm profile. Alarm Name These types of alarms can trigger an action.
Page 194: Cip Sync Time Synchronization (Precision Time Protocol)
Chapter 7 Configure Switch Features CIP Sync Time CIP Sync time synchronization refers to the IEEE 1588 standard for Precision Time Protocol (PTP). The protocol enables precise synchronization of clocks Synchronization in measurement and control systems. Clocks are synchronized with (Precision Time Protocol) nanosecond accuracy over the EtherNet/IP communication network.
Page 195: End To End Transparent Mode
In Forward mode, the switch passes PTP packets as normal multicast traffic. All switch ports are PTP-enabled by default. Forward mode is the default mode. NTP-PTP Clock Mode (Stratix 5400 and 5410 Switches) In NTP-PTP Clock mode, the switch functions as the grandmaster clock and boundary clock: •...
Page 196: Configure Time Synchronization Via Device Manager
Chapter 7 Configure Switch Features Before you configure a switch to use NTP-PTP clock mode, do the following: • Configure NTP, as described on page 295. While NTP-PTP Clock mode requires only one NTP time source, as a best practice, we recommend you configure two or more NTP time sources.
Page 197 Configure Switch Features Chapter 7 4. To complete the remaining fields, refer to the figure and table that corresponds to your mode. Mode Page Boundary End to End Forward NTP-PTP Clock Figure 3 - Boundary Mode Table 33 - Boundary Mode Fields Field Description PTP Clock Settings...
Page 198 Chapter 7 Configure Switch Features Table 33 - Boundary Mode Fields (continued) Field Description Clock Quality Displays a summary of the quality of the grandmaster clock: • Class—Time and frequency traceability of the grandmaster clock. • Accuracy—Expected accuracy of the grandmaster clock when the Best Master Clock algorithm is in use. •...
Page 199 Configure Switch Features Chapter 7 Table 33 - Boundary Mode Fields (continued) Field Description Announce Interval Type the time interval, specified as the logarithmic mean in seconds, for sending announce messages. Valid values: • 0—1 second • 1—2 seconds • 2— 4 seconds •...
Page 200 Chapter 7 Configure Switch Features Table 34 - End to End Transparent Mode Fields (continued) Field Description Per Port Settings Port Name Displays the port type and port number: • Fa—Fast Ethernet • Gi—Gigabit Ethernet • Te—TenGigabit Ethernet State Displays the synchronization state of the switch port with the parent or grandmaster clock: (Not available on •...
Page 201 Configure Switch Features Chapter 7 Table 34 - End to End Transparent Mode Fields (continued) Field Description Sync Interval Type the time interval, specified as the logarithmic mean in seconds, for sending synchronization messages. (Not available on Valid values: Stratix 8000/8300 switches) •...
Page 202 Chapter 7 Configure Switch Features Figure 6 - NTP-PTP Clock Mode Table 36 - NTP-PTP Clock Mode Fields Field Description PTP Clock Settings PTP Device Type Displays the PTP clock type of the switch, as determined by the Mode setting. Number of PTP ports Displays the number of ports assigned to the PTP clock.
Page 203 Configure Switch Features Chapter 7 Table 36 - NTP-PTP Clock Mode Fields (continued) Field Description Time Source Displays the time source used by the grandmaster clock. Device Clock Details Device Time Source Displays the time source used by the switch. Device Clock Time Displays the time on the switch, obtained from the time source.
Page 204: Application
Chapter 7 Configure Switch Features Table 36 - NTP-PTP Clock Mode Fields (continued) Field Description Sync Interval Type the time interval, specified as the logarithmic mean in seconds, for sending synchronization messages. Valid values: • -1—half second • 0—1 second •...
Page 205 Configure Switch Features Chapter 7 Figure 7 - Boundary Mode Table 37 - Boundary Mode Field Description Clock Identity Displays a unique identifier for the clock. Grandmaster Selection Priority1 Type a value to override the default criteria (clock quality, clock class, and so on) for the best master clock selection. A lower value takes precedence.
Page 206 Chapter 7 Configure Switch Features Table 37 - Boundary Mode (continued) Field Description Delay Request The logarithmic mean interval in seconds. Type the recommended to connected devices to send delay request messages when the switch port is in the master state. Valid values: •...
Page 207 Configure Switch Features Chapter 7 Figure 8 - End-to-End Transparent Mode Table 38 - End to End Transparent Mode Fields Field Description Port Displays the port type and port number: • Fa—Fast Ethernet • Gi—Gigabit Ethernet • Te—TenGigabit Ethernet Enable Check the checkbox for each port on which to enable PTP.
Page 208 Chapter 7 Configure Switch Features Figure 10 - NTP-PTP Mode Table 39 - NTP-PTP Mode Fields Field Description Clock Identity Displays a unique identifier for the clock. Grandmaster Selection Type a value to override the default criteria (clock quality, clock class, and so on) for the best master clock selection. A lower value takes Priority1 precedence.
Page 209: View Time Sync Information In The Logix Designer Application
Configure Switch Features Chapter 7 Table 39 - NTP-PTP Mode Fields (continued) Field Description Delay Request Interval Type the recommended to connected devices to send delay request messages when the switch port is in the master state. Valid values: • -1—half second •...
Page 210 Chapter 7 Configure Switch Features Figure 11 - Time Sync Information Table 40 - Time Sync Information Fields Field Description CIP Sync Time Synchronization Displays whether the Precision Time Protocol is enabled or disabled on the device. UTC System Time Displays the current system time in units of microseconds.
Page 211 Configure Switch Features Chapter 7 Table 40 - Time Sync Information Fields (continued) Field Description Class Displays a measure of the quality of the local clock. Values are defined from 0…255 with 0 as the best clock. Accuracy Indicates the expected absolute accuracy of the local clock relative to CIP Sync time synchronization epoch (31 December, 1969 23:59:51.99918 UTC).
Page 212: Cryptographic Ios
SSH remains disabled, and HTTP remains the default protocol for Device Manager. Device-level Ring (DLR) DLR is available on Stratix 5400 switches and some models of Stratix 5700 and ArmorStratix 5700 switches. For a list of switches that support DLR, see page This section covers the following topics: •...
Page 213: Overview
IMPORTANT Stratix 5700 and ArmorStratix 5700 switches support only one ring per switch. Stratix 5400 switches support as many as three rings per switch. Figure 13 - A DLR network includes the following nodes. Rockwell Automation Publication 1783-UM007G-EN-P - February 2017...
Page 214 Chapter 7 Configure Switch Features Node Description Supervisor node A DLR network requires at least one node to be configured as ring supervisor. IMPORTANT: By default, the supervisor function is disabled on supervisor-capable devices, so they are ready to participate in a linear network or as a ring node on a DLR network.
Page 215: Dlr Port Choices
• Stratix 5700 and ArmorStratix 5700 switches support one ring and two DLR-enabled ports per switch. • Stratix 5400 switches support as many as three rings and six DLR-enabled ports per switch. We recommend that you use the Multiport Automation Device Smartport role on ports you configure for DLR.
Page 216: Dlr Considerations
Chapter 7 Configure Switch Features Table 42 - DLR Port Choices for Stratix 5700 and ArmorStratix 5700 Switches Switch Port 1783-BMS10CGP Fa 1/7 Fa 1/8 Gi 1/1 Gi 1/2 1783-BMS10CGN Fa 1/7 Fa 1/8 Gi 1/1 Gi 1/2 1783-BMS12T4E2CGL Fa 1/15 Fa 1/16 Gi 1/1 Gi 1/2...
Page 217: Redundant Gateways
Configure Switch Features Chapter 7 Redundant Gateways Stratix 5400, Stratix 5700, ArmorStratix 5700 switches that support DLR also support redundant gateways. IMPORTANT Redundant gateways do not work with End to End Transparent mode for Precision Time Protocol. For more information about End to End Transparent...
Page 218 Chapter 7 Configure Switch Features Figure 14 shows an example of a switch configured for redundant gateway. All ports are assigned to VLAN 1. Figure 14 - Redundant Gateway Switch Ports Port Configuration DLR access port DLR access port Redundant gateway uplink port Redundant gateway uplink port Non-DLR port When the switch acts as the active redundant gateway, traffic on the switch...
Page 219 Configure Switch Features Chapter 7 Figure 15 - Traffic from Backup Gateway to Ring Switch Switch Switch Switch DLR Device DLR Active DLR Backup Gateway Gateway DLR Active Supervisor Rockwell Automation Publication 1783-UM007G-EN-P - February 2017...
Page 220 Chapter 7 Configure Switch Features You can configure redundant gateways on switches that are either ring supervisors or ring nodes. Figure 16 shows two Stratix 5700 switches that are configured as ring supervisors with redundant gateway: • One switch is configured as the active ring supervisor and also the active redundant gateway.
Page 221 Configure Switch Features Chapter 7 Figure 17 shows two Stratix 5700 switches that are configured as ring nodes with redundant gateway: • One switch is a ring node and the active redundant gateway. • The other switch is a ring node and the backup redundant gateway. In this example, the switch provides redundant gateway functionality, so that all ring nodes have access to the outside network.
Page 222: Dhcp For Ring Devices
Chapter 7 Configure Switch Features DHCP for Ring Devices Stratix 5400, Stratix 5700, and ArmorStratix 5700 switches that support DLR also support DHCP for ring devices. IMPORTANT DHCP for ring devices does not work with DHCP peristence, as described on page 241.
Page 223 Configure Switch Features Chapter 7 DHCP snooping for a ring can be enabled or disabled. By default, DHCP snooping for a ring is enabled: • When enabled, DHCP snooping prevents DHCP address assignments from going beyond an active ring DCHP server and the devices within the ring.
Page 224 Chapter 7 Configure Switch Features In this example, the active ring DHCP server recognizes IP address requests from ring devices 3, 4, and 6 and responds with the position-based IP address specified in the DHCP table (Table 43). The ring device index numbers in the DCHP table begin incrementing in order from the device connected to the lowest DLR port.
Page 225: Multiple Rings (Stratix 5400 Switches)
• All ring ports within the same ring or belonging to different rings must be assigned to the same access VLAN. • The same Stratix 5400 switch must serve as the active gateway for all rings. • The same Stratix 5400 switch must serve as the backup gateway for all rings.
Page 226: Configure Dlr Via Device Manager
Chapter 7 Configure Switch Features Configure DLR via Device Manager IMPORTANT Be sure to configure DLR on the switch prior to connecting ring ports. Connecting both ring ports on a switch that has not yet been configured for DLR can result in undesired behavior and limit the ability to configure the switch.
Page 227 Configure Switch Features Chapter 7 Table 44 - Config DLR Fields Field Description DLR Ring ID (Stratix 5400 switches). Choose the ring number to configure: • Ring 1 • Ring 2 • Ring 3 Mode Choose one of these modes: •...
Page 228 Chapter 7 Configure Switch Features Table 44 - Config DLR Fields (continued) Field Description Advertise Timeout Type the duration of time for nodes to wait before timing out in the absence of received advertise messages. Valid values: 200…500,000 μs Default: 5000 μs Learning Update Check the checkbox to enable learning update messages.
Page 229 Configure Switch Features Chapter 7 Assign IP Addresses to Ring Devices Use the table on the Config DHCP tab to assign IP addresses to devices based on their position in the ring. To add IP addresses individually, click Add Entry. Field Description Index...
Page 230: Configure Dlr Via The Logix Designer Application
Configuration parameters appear for the number of available rings: • Stratix 5700 and ArmorStratix 5700 switches show one ring. • Stratix 5400 switches show three rings. Configure each ring: • To enable DLR on specified ring ports and to view information about...
Page 231 Configure Switch Features Chapter 7 Table 46 - Device Level Ring (DLR) Fields Field Description Enable Ring 1/Enable Ring 2/Enable Ring 3 Check to enable DLR on the ports that are specified in the associated Port 1 and Port 2 fields for the ring. Port 1 Choose a ring port.
Page 232 Chapter 7 Configure Switch Features Table 46 - Device Level Ring (DLR) Fields (continued) Field Description Active Ring Supervisor Displays the IP address of the active ring supervisor. DCHP Server Role Displays the role of the ring DHCP server. Valid values: •...
Page 233 Configure Switch Features Chapter 7 Table 47 - Ring 1/Ring 2/Ring 3 Fields (continued) Field Description Active Supervisor Precedence Displays the precedence that is assigned to the ring supervisor. You assign the precedence value on the Advanced Network Configuration dialog box. See Table Enable Supervisor Mode Check to make the switch a ring supervisor.
Page 234 Chapter 7 Configure Switch Features Table 48 - Advanced Network Configuration Fields Field Description Beacon Interval Type an interval for the supervisor to transmit beacon frames. Valid values: 200…100,000 μs The default interval i s 400 μs. Beacon Timeout Type the amount of time ring nodes wait before timing out in the absence of received beacon messages. Valid values: 400…500,000 μs The default timeout is 1960 μs.
Page 235 Configure Switch Features Chapter 7 Table 49 - Redundant Gateway Configuration Fields (continued) Field Description Precedence Choose a role to assign to the redundant gateway that corresponds to a predefined precedence value. The switch transmits the precedence value is advertise messages and is used to select the redundant gateway when multiple redundant gateways are configured. A higher value means higher precedence.
Page 236: Dhcp Server
Chapter 7 Configure Switch Features Table 50 - DHCP Fields Field Description IP Address Displays the IP address of the ring member. The IP address is reserved for the selected port and is not available for normal DHCP assignment. The IP address must be an address from the pool specified in DHCP IP address pool. To assign IP addresses to ring members, see Refer to Assign IP Addresses to Ring Members on page 236.
Page 237 Configure Switch Features Chapter 7 2. From the DHCP Pool field, choose the name of the IP address pool to use for ring devices. This pool must be previously configured, as described on page 243. DHCP persistance and DHCP for ring devices can coexist, but cannot share the same pool.
Page 238: Dynamic Host Configuration Protocol (Dhcp) Persistence
Chapter 7 Configure Switch Features Dynamic Host Configuration Every device in an IP-based network must have a unique IP address. DHCP assigns IP address information from a pool of available addresses to newly Protocol (DHCP) Persistence connected devices (DHCP clients) in the network. If a device leaves and then rejoins the network, the device receives the next available IP address, which is not necessarily the same address that it had before.
Page 239 Configure Switch Features Chapter 7 3. To enable DHCP snooping, check the DHCP Snooping checkbox. DHCP snooping restricts the broadcast of DHCP requests beyond the connected switch. As a result, devices receive address assignments from only the connected switch. This option is available only on ports assigned to a VLAN.
Page 240 Chapter 7 Configure Switch Features 3. Complete the fields and click OK. Field Description DHCP Pool Name The name of the DHCP IP address pool that is configured on the switch. The name can have up to 31 alphanumeric characters. The name cannot contain a ? or a tab.
Page 241 Configure Switch Features Chapter 7 Reserve IP Addresses through DHCP Persistence IMPORTANT DHCP persistence does not work with DHCP for ring devices, as described on page 222. Configure only one of these features on your switch. You can reserve and preassign an IP address from the IP address pool to a specific switch port.
Page 242 Chapter 7 Configure Switch Features The following figure and table illustrate DHCP persistence behavior. Switch 1 Switch 2 Table 51 - DHCP Persistence Behavior Then • Switch 1 has ports FA1…FA3 in its persistence table A new device that is connected to switch 1 FA1 receives an IP address from the switch 1 persistence table. •...
Page 243: Configure Dhcp Via The Logix Designer Application
Configure Switch Features Chapter 7 Configure DHCP via the Logix Designer Application In the navigation pane, click DHCP Address Assignment. You can assign a specific IP address to each port, so that the device attached to a given port receives the same IP address. Table 53 - DHCP Address Assignment Fields Field Description...
Page 244: Etherchannels
Each EtherChannel can consist of up to eight compatible, configured Ethernet ports. Table 54 - EtherChannels by Switch Switch EtherChannels, max Stratix 5400 Stratix 5410 Stratix 5700 ArmorStratix 5700 Stratix 8000/8300 (1) EtherChannels are available only on swithes with Full firmware.
Page 245 Configure Switch Features Chapter 7 Figure 21 shows two EtherChannels. Two Full-duplex 10/100/1000-Mbps ports on Switches A and C create an EtherChannel with a bandwidth of up to 4 Gbps between both switches. Similarly, two Full-duplex 10/100 ports on Switches B and D create an EtherChannel with a bandwidth of up to 400 Mbps between both switches.
Page 246: Configure Etherchannels Via Device Manager
Chapter 7 Configure Switch Features Configure both ends of the EtherChannel in the same mode: • When you configure one end of an EtherChannel in PAgP or LACP mode, the system negotiates with the other end of the channel to determine the ports to become active.
Page 247: Configure Etherchannels Via The Logix Designer Application
Configure Switch Features Chapter 7 Configure EtherChannels via the Logix Designer Application In the navigation pane, click EtherChannels. You can add, edit, and delete EtherChannel members. Table 57 - EtherChannels Fields Field Description EtherChannel A number to identify the EtherChannel. See Table 54 for the maximum number of EtherChannels available per switch.
Page 248: Motion Prioritized Qos Macros
Integrated Motion on the EtherNet/IP network by applying the following QoS macros in Device Manager. Table 58 - Motion Prioritized QoS Macros Switch Macro Stratix 5400 Motion Prioritized QoS Stratix 5410 Stratix 5700 Motion Prioritized QoS Step 1 Motion Prioritized QoS Step 2...
Page 249: Configure Motion Prioritized Qos Macros Via Device Manager
QoS settings applied during Express Setup remain active. Figure 22 - QoS Macros for Stratix 5700, ArmorStratix 5700, and Stratix 8000 Switches Figure 23 - QoS Macro for Stratix 5400 and 5410 Switches Rockwell Automation Publication 1783-UM007G-EN-P - February 2017...
Page 250: Horizontal Stacking
Chapter 7 Configure Switch Features Horizontal Stacking Horizontal stacking lets you manage as many as four Stratix 5410 switches as one logical device. To stack multiple switches, you connect the switches via as many as two uplink Ethernet ports per switch. You use the CLI to configure network ports as designated stack ports.
Page 251: Device Manager
Configure Switch Features Chapter 7 You can configure a stack in either a ring topology (Figure 25) or a linear topology (Figure 26). Figure 25 - Switch Stack in a Ring Topology 32648-M Figure 26 - Switch Stack in a Linear Topology 32649-M Table 59 lists the supported features for horizontal stacking.
Page 252: Internet Group Management Protocol (Igmp) Snooping With Querier
Table 60 - Default Supported Multicast Groups Switch Default Multicast Groups Stratix 5400 and Stratix 5410 switches 1024 Stratix 5700 and ArmorStratix 5700 switches If you exceed 180 multicast groups, we recommend that you switch to the routing SDM template via Device Manager.
Page 253: Configure Igmp Snooping Via Device Manager
Configure Switch Features Chapter 7 Configure IGMP Snooping via Device Manager From the Configure menu, choose IGMP Snooping: • To enable IGMP Snooping for all VLAN IDs, check Enable next to IGMP Snooping. • To enable IGMP Querier for all VLAN IDs, check Enable next to IGMP Querier.
Page 254: Network Address Translation (Nat)
Chapter 7 Configure Switch Features Network Address Translation For a list of switches that support NAT, see page (NAT) NAT is a service that translates one IP address to another IP address via a NAT-configured switch. The switch translates the source and destination addresses within data packets as traffic passes between subnets.
Page 255 Figure 27 - Layer 3 Example with NAT in Stratix 5700 Switch HMI 10.200.1.2 VLAN 200 VLAN 200 Line Controller 10.200.1.3 Stratix 5400 with Layer 3 Firmware Controller 1 to Line Controller VLAN 10: 10.10.1.1 NAT Gateway: 192.168.1.1 VLAN 200: 10.200.1.1 Controller 2 to Line Controller...
Page 256 Chapter 7 Configure Switch Features Figure 28 - Layer 3 Example with NAT in Stratix 5410 Layer 3 Firmware Model HMI 10.200.1.2 VLAN 200 VLAN 200 Line Controller 10.200.1.3 Stratix 5410 with Layer 3 Firmware VLANs 10...80: 10.10.1.1...10.10.8.1 Controllers 1...8 communicate NAT Gateway: 192.168.1.1 with each other and the line controller.
Page 257 Figure 29 - Layer 2 Example with NAT in Stratix 5700 Switch HMI 10.10.1.101 Line Controller VLAN 10 VLAN 10 10.10.1.100 192.168.1.100 Controller 1 to Line Controller Stratix 5400 Layer 2 Firmware Model VLAN 10: 10.10.1.1 Controller 2 to Line Controller VLAN 10 VLAN 10 Machine 1 Mach chin...
Page 258 Chapter 7 Configure Switch Features Figure 30 - Layer 2 Example with NAT in Stratix 5410 Layer 2 Firmware Model HMI 10.10.1.101 Line Controller VLAN 10 VLAN 10 10.10.1.100 192.168.1.100 Controllers 1...8 communicate Stratix 5410 Layer 2 Firmware Model with each other and the line controller. with NAT VLAN 10: 10.10.1.1 NAT Instances on NAT Ports 1...8...
Page 259 Table 62 - Maximum Translation Entries Switch Maximum Translation Entries Stratix 5400 and Stratix 5700 128 across all NAT ports. Stratix 5410 128 across NAT ports 1…6 and 13…18. 128 across NAT ports 7…12, 19…24, and 25…28.
Page 260: Vlan Assignments
Chapter 7 Configure Switch Features VLAN Assignments When configuring NAT, you can assign one or more VLANs to a NAT instance. When you assign a VLAN to a NAT instance, the traffic that is associated with that VLAN is subject to the configuration parameters of the NAT instance.
Page 261: Configuration Considerations
• All switches can translate only IPv4 addresses. • All switches can have a maximum of 128 NAT instances. • Switch-specific features are shown in the following table. Feature Stratix 5700 Switch Stratix 5400 Switch Stratix 5410 Switch Uplink Ports Downlink Ports Translation Entries (1) A subnet translation counts as only one translation entry, but includes translations for many devices (2) Both uplink and downlink ports can be configured for as many as 8 NAT ports.
Page 262: Traffic Permits And Fixups
Chapter 7 Configure Switch Features Traffic Permits and Fixups While a NAT-configured port can translate many types of traffic, only unicast and broadcast traffic are supported. You can choose to block or pass through the following unsupported traffic types: • Untranslated unicast traffic •...
Page 263: Rockwell Automation Publication 1783-Um007G-En-P - February
Configure Switch Features Chapter 7 Create NAT Instances for Traffic Routed through a Layer 3 Switch or Router To create a NAT instance for traffic that is routed through a Layer 3 switch or router, follow these steps. 1. From the Configure menu, choose NAT to display the NAT window. 2.
Page 264 Chapter 7 Configure Switch Features VLAN Selection for Stratix 5700 and 5400 Switches VLAN Selection for Stratix 5410 Switches Rockwell Automation Publication 1783-UM007G-EN-P - February 2017...
Page 265 Configure Switch Features Chapter 7 3. In the Name field, type a unique name to identify the instance. The instance name cannot include spaces or exceed 32 characters. 4. Complete VLAN assignments: • (Stratix 5700 and 5400 switches) For each uplink port on the right, select each VLAN to assign to the instance.
Page 266 Chapter 7 Configure Switch Features Field Description Public IP Address Type a public IP address: • To translate one address, type a unique public address to represent the device. • To translate a range of addresses, type the first address in the range of sequential addresses. •...
Page 267 Configure Switch Features Chapter 7 Create NAT Instances for Traffic Routed through a Layer 2 Switch To create a NAT instance for traffic that is routed through a Layer 2 switch, follow these steps. 1. From the Configure menu, choose NAT to display the NAT window. 2.
Page 268 Chapter 7 Configure Switch Features VLAN Selection for Stratix 5700 and 5400 Switches VLAN Selection for Stratix 5410 Switches Rockwell Automation Publication 1783-UM007G-EN-P - February 2017...
Page 269 Configure Switch Features Chapter 7 3. In the Name field, type a unique name to identify the instance. The instance name cannot include spaces or exceed 32 characters. 4. Complete VLAN assignments: • (Stratix 5700 and 5400 switches) For each uplink port on the right, select each VLAN to assign to the instance.
Page 270 Chapter 7 Configure Switch Features Field Description Public IP Address Type a public IP address: • To translate one address, type a unique public address to represent the device. • To translate a range of addresses, type the first address in the range of sequential addresses. •...
Page 271 Configure Switch Features Chapter 7 6. Click the Public to Private tab. 7. Click Add Row, complete the fields, and click Save. Field Description Public IP Address Type a public IP address: • To translate one address, type the existing address for the device on the public subnet. •...
Page 272 Chapter 7 Configure Switch Features Field Description Private IP Address Type a private IP address: • To translate one address, type a unique private address to represent the device. • To translate a range of addresses, type the first address in the range of sequential addresses. •...
Page 273 Configure Switch Features Chapter 7 Configure Traffic Permits and Fixups Use caution when you configure traffic permits and fixups. We recommend that you use the default values. To configure traffic permits or fixups, follow these steps. 1. Click the Advanced tab. 2.
Page 274: Configure Nat Via The Logix Designer Application
Chapter 7 Configure Switch Features Configure NAT via the Logix Designer Application For Stratix 5410 switches, see page 286. In the navigation pane, click NAT. Table 63 - NAT Fields Field Description Instance Name Displays the unique name of the NAT instance. Gi1/1 VLANs Displays the VLANs assigned to each NAT instance on port Gi1/1.
Page 275 Configure Switch Features Chapter 7 To configure NAT, follow one of these procedures that are based on your application: • Create NAT Instances for Traffic Routed through a Layer 3 Switch or Router For an example of this application, see Figure 28 on page 256.
Page 276 Chapter 7 Configure Switch Features 2. In the Name field, type a unique name to identify the instance. The instance name cannot include spaces or exceed 32 characters. 3. In the VLAN Association area, check the checkbox next to each VLAN to assign to the instance.
Page 277 Configure Switch Features Chapter 7 Table 65 - Range Translation Field Description Type of Entry Choose Range. Starting Private IP Address Type the existing starting address for the device on the private subnet. Starting Public IP Address Type a unique, starting public address to represent the device. Range Type the number of addresses to include in the range.
Page 278 Chapter 7 Configure Switch Features Table 66 - Subnet Translation (continued) Field Description Subnet Mask Choose the subnet mask for the addresses to translate. Valid values: • Class B: 255.255.0.0 • Class C: 255.255.255.0 • Portion of Class C: – 255.255.255.128 (provides 128 addresses per translation entry –...
Page 279 Configure Switch Features Chapter 7 Create NAT Instances for Traffic Routed through a Layer 2 Switch To create a NAT instance for traffic that is routed through a Layer 2 switch, follow these steps. 1. From the NAT view, click New Instance to display the General tab. 2.
Page 280 Chapter 7 Configure Switch Features 5. Do one of the following: • To translate one address for a device on the private subnet that communicates on the public subnet, see Table • To translate a range of addresses for devices on the private subnet that communicates on the public subnet, see Table 68 •...
Page 281 Configure Switch Features Chapter 7 Table 69 - Subnet Translation Field Description Type of Entry Choose Subnet. Starting Private IP Address Type the existing starting address for a device on the private subnet. This address must correspond to the size of the subnet mask to translate. Subnet Mask Starting Private Subnet Address 255.255.0.0...
Page 282 Chapter 7 Configure Switch Features 6. Click OK. 7. Click the Public to Private tab. 8. Click New Entry to display the New Entry dialog box. 9. Do one of the following: • To translate one address for a device on the public subnet that communicates on the private subnet, see Table •...
Page 283 Configure Switch Features Chapter 7 Table 70 - Single Translation Field Description Type of Entry Choose Single. Single is the default value. Starting Public IP Address Type the existing address for the device on the public subnet. Starting Private IP Address Type a unique private address to represent the device.
Page 284 Chapter 7 Configure Switch Features Table 72 - Subnet Translation (continued) Field Description Starting Private IP Address Type a unique, starting private address to represent the devices. This address must correspond to the size of the subnet mask to translate. Subnet Mask Starting Private Subnet Address 255.255.0.0...
Page 285 Configure Switch Features Chapter 7 Configure Traffic Permits and Fixups Use caution when you configure traffic permits and fixups. We recommend that you use the default values. To configure traffic permits or packet fixups, follow these steps. 1. Click the Advanced tab. 2.
Page 286: Configure Nat Via The Logix Designer Application
Chapter 7 Configure Switch Features Configure NAT via the Logix Designer Application (Stratix 5410 Switches) In the navigation pane, click NAT. Table 73 - NAT Fields Field Description Instance Name Displays the unique name of the NAT instance. Port Type Identifies the port type as either uplink or downlink: •...
Page 287 Configure Switch Features Chapter 7 To create a NAT instance, follow these steps. IMPORTANT Configure all Smartport roles and VLANs before creating NAT instances. If you change a Smartport role or the native VLAN for a port that is associated with a NAT instance, you must reassign VLANs to the NAT instance.
Page 288 Chapter 7 Configure Switch Features 2. Configure the ports to assign to the instance. a. In the NAT Instance Name field, type a unique name to identify the instance. b. Click the type of ports to assign to the NAT instance: •Uplink Ports Only (Te1/25…Te1/28) •(Default) Downlink Ports Only (Gi1/1…Gi1/24) c.
Page 289 Configure Switch Features Chapter 7 4. For each port, select one or more VLANs to assign to the NAT instance. The VLANs available for selection are VLANs previously assigned to the port. You can select the same VLAN for multiple ports. VLANs assigned to another NAT instance are unavailable for selection.
Page 290 Chapter 7 Configure Switch Features If you assigned multiple VLANs to the NAT instance, no gateway configuration is necessary. Rockwell Automation Publication 1783-UM007G-EN-P - February 2017...
Page 291 Configure Switch Features Chapter 7 6. Click Next to display the Translations view. Rockwell Automation Publication 1783-UM007G-EN-P - February 2017...
Page 292 Chapter 7 Configure Switch Features 7. Configure translations for one device, a range of devices, or all devices on a subnet. Field Description Device Location Choose the type of network on which the device resides: • Private Network • Public Network Private IP Address Specify a private IP address.
Page 293 Configure Switch Features Chapter 7 Table 74 - Valid Subnet Addresses Subnet Mask Subnet Address 255.255.0.0 The last two octets of the address must end in 0. EXAMPLE: Private address: 192.168.0.0 Public address: 10.200.0.0 255.255.255.0 The last octet of the address must end in 0. EXAMPLE: Private address: 192.168.1.0 Public address: 10.200.1.0...
Page 294: View Address Translations In Rslinx Software
Chapter 7 Configure Switch Features 9. In the Incoming and Outgoing fields for each type of traffic, choose one of these options: • Pass-Through—Permit unsupported packets to pass across the NAT boundary. • Blocked—Drop unsupported packets. 10. To disable protocol fixups for ARP, clear the Fix up ARP checkbox. 11.
Page 295: Network Time Protocol (Ntp)
Configure Switch Features Chapter 7 Network Time Protocol (NTP) Network Time Protocol (NTP), documented in RFC 1305, is the traditional method of synchronizing clocks across packet-based networks. NTP uses a two-way time transfer mechanism between a master and a slave. NTP is capable of synchronizing devices in a tightly-controlled network.
Page 296 Chapter 7 Configure Switch Features You can add, edit, and delete NTP associations in the table area on the NTP page. You can add multiple NTP servers. To add an association, follow these steps. 1. Click Add. 2. In the IP Address field, specify one of the following: •...
Page 297: Parallel Redundancy Protocol (Prp)
Displays the relative time of the peer clock to the local clock in milliseconds. Parallel Redundancy Stratix 5400 and 5410 switches support PRP as a redundancy box (RedBox). As a RedBox, PRP sends duplicate packets from two different ports on Protocol (PRP) independent network paths.
Page 298: Configure Prp Via Device Manager
Chapter 7 Configure Switch Features Traffic egressing the RedBox PRP channel group can be mixed, that is, destined to either SANs (connected only on either LAN-A or LAN-B) or DANs. To avoid duplication of packets for SANs, the switch learns source MAC addresses from received supervision frames for DAN entries and source MAC addresses from non-PRP (regular traffic) frames for SAN entries.
Page 299 • 2 Port 1 Choose a port to be a member of the channel group: • Valid ports on Stratix 5400 switches: Gi1/1 and Gi1/2 • Valid ports on Stratix 5410 switches: Gi1/17 and Gi1/18 Port 2 Choose a port to be a member of the channel group: •...
Page 300 Chapter 7 Configure Switch Features VDAN Table To add an entry to the PRP VDAN table, follow these steps. 1. From the PRP window, click the VDAN Table tab. 2. Click Add, and then complete the fields, and then click OK. Field Description Channel Group Number Choose a channel group number:...
Page 301: Port Mirroring
Configure Switch Features Chapter 7 Port Mirroring Port mirroring is for advanced users with experience in troubleshooting traffic and protocol issues on networks. Port mirroring copies, or mirrors, traffic on one port to a monitoring port where a network protocol analyzer tool can capture the packet.
Page 302: Configure Port Mirroring In Device Manager
Chapter 7 Configure Switch Features Configure Port Mirroring in Device Manager To configure port mirroring, follow these steps. 1. From the Configure menu, choose Smartports. 2. Select the checkbox next to the port to do the monitoring, and then click Edit. 3.
Page 303: Port Security
Configure Switch Features Chapter 7 Port Security Stratix managed switches implement MAC address-based port security. A MAC address is a unique address that is assigned to each Ethernet-capable device. Switches can enforce communication either dynamically or statically per MAC address. With dynamic port security, a switch port communicates with some number of devices.
Page 304: Static Secure Mac Address (Mac Id)
Chapter 7 Configure Switch Features Static Secure MAC Address (MAC ID) The other method of limiting MAC IDs is to configure statically one or more MAC IDs for a port by defining them via port security with Device Manager. These addresses become part of the saved configuration of the switch. This method provides strong security.
Page 305 Configure Switch Features Chapter 7 Port security limits and identifies the MAC addresses of devices that can send traffic through the switch port. The switch port does not forward traffic from devices outside the defined group of devices. A security violation occurs when any of the following conditions occur: •...
Page 306 Chapter 7 Configure Switch Features To change the Static MAC Addresses table for a port, follow these steps. 1. Click the radio button next to the port to configure. 2. Click Edit. 3. Clear or check the Enable checkbox. 4. Configure MAC addresses as follows: •...
Page 307: Configure Port Security Via The Logix Designer Application
Configure Switch Features Chapter 7 Configure Port Security via the Logix Designer Application In the navigation pane, click Port Security. For Stratix 8000/8300 switches, use Advanced Port Configuration, as described on page 308. Figure 32 - Port Security Table 78 - Port Security Fields Field Description Port...
Page 308 Chapter 7 Configure Switch Features For Stratix 8000/8300 switches, in the navigation pane, click Advanced Port Configuration. Figure 33 - Advanced Port Configuration for Stratix 8000/8300 Switches Table 79 - Advanced Port Configuration Fields for Stratix 8000/8300 Switches Field Description Unit Indicates where the port resides: •...
Page 309: Port Thresholds
Configure Switch Features Chapter 7 Port Thresholds Port thresholds prevent traffic on a LAN from being disrupted by a broadcast, multicast, or unicast storm on one of the physical interfaces. Port thresholds do not apply to switches with lite firmware. A LAN storm occurs when packets flood the LAN, creating excessive traffic and degrading network performance.
Page 310: Outgoing (Rate Limiting)
Chapter 7 Configure Switch Features Figure 34 - Port Thresholds Example Forwarded Traffic Blocked Traffic Total Number of Broadcast Threshold Packets or Bytes Time The combination of the storm-control suppression level and the 1-second time interval controls the way the port thresholds algorithm works. A higher threshold enables more packets to pass through.
Page 311: Configure Port Thresholds Via Device Manager
Configure Switch Features Chapter 7 Configure Port Thresholds via Device Manager From the Configure menu, choose Port Thresholds. Table 80 - Port Threshold Fields Field Description Incoming Unicast For each port, do the following: 1. Check or clear the Enable checkbox. Multicast 2.
Page 312: Configure Port Thresholds Via The Logix Designer Application
Figure 35 - Port Thresholds for Stratix 5400, Stratix 5410, Stratix 5700, and ArmorStratix 5700 Switches Table 81 - Port Threshold Fields for Stratix 5400, Stratix 5410, Stratix 5700, and ArmorStratix 5700 Switches Field...
Page 313 Configure Switch Features Chapter 7 Figure 36 - Port Thresholds for Stratix 8000/8300 Switches Table 82 - Port Threshold Fields for Stratix 8000/8300 Switches Field Description Unit Indicates where the port resides: • Base (for example, 1783-MS10T) • Expansion module (for example, 1783-MX08T) Port Indicates the port that is selected for configuration.
Page 314: Power Over Ethernet (Poe)
Chapter 7 Configure Switch Features Power over Ethernet (PoE) Switches and expansion modules with PoE ports are software-configurable and provide these features: • Support for IEEE 802.3af (PoE)-compliant devices. • Support for IEEE 802.3at Type 2 (PoE+), which increases the available power that can be drawn by powered devices from 15.4…30 W per port.
Page 315: Powered Device Detection And Initial Power Allocation
Configure Switch Features Chapter 7 Configuration options include the following: • Limit the total power supported. • Configure mode and power settings for individual ports. For most applications, the default configuration (Auto mode) is sufficient and no further configuration is required. However, you can customize the settings to meet your needs.
Page 316: Power Management Modes
Chapter 7 Configure Switch Features • A Cisco pre-standard powered device does not provide its power requirement when the switch detects it. A port that is not configured for PoE+ allocates 15.4 W as the initial allocation for power budgeting. A port that is configured for a PoE+ switch allocates 30 W.
Page 317 Configure Switch Features Chapter 7 If enough power is available for all powered devices that are connected to the switch, power is turned on to all devices. If there is not enough power to accommodate all connected devices and if a device is reconnected while other devices are waiting for power, it cannot be determined which devices are granted or are denied power.
Page 318 Chapter 7 Configure Switch Features Maximum Power Allocation (cutoff power) on a PoE Port The switch determines the cutoff power on a PoE port in this order. 1. Manually when you configure the power level to budge for the port 2.
Page 319: Configure Poe Ports Via Device Manager
Configure Switch Features Chapter 7 Because the switch supports external removable power supplies for PoE/PoE+ and can configure the budget per the power supply that is used, the total amount of power available varies depending on the power supply configuration: •...
Page 320 Chapter 7 Configure Switch Features Figure 38 - PoE Configuration for Stratix 5400, Stratix 5700, and ArmorStratix 5700 Switches Figure 39 - PoE Configuration for Stratix 8000/8300 Switches Table 84 - Power Management Fields Field Description Selected Module Choose a connected PoE module for which to view status information: (Stratix 8000/8300 switches) •...
Page 321 Configure Switch Features Chapter 7 Table 84 - Power Management Fields (continued) Field Description Mode Displays the Power Management mode of the port: • Auto—(Default) Enables the detection of powered devices and automatically allocates power to the PoE port if a device is connected. To limit the power that is used by this port, adjust the Max Power setting.
Page 322: Configure Poe Via The Logix Designer Application
Chapter 7 Configure Switch Features Configure PoE via the Logix Designer Application In the navigation pane, click PoE. Figure 40 - PoE Configuration for Stratix 5410 Switches Rockwell Automation Publication 1783-UM007G-EN-P - February 2017...
Page 323 Configure Switch Features Chapter 7 Figure 41 - PoE Configuration for Stratix 5400, Stratix 5700, and ArmorStratix 5700 Switches Figure 42 - PoE Configuration for Stratix 8000/8300 Switches Rockwell Automation Publication 1783-UM007G-EN-P - February 2017...
Page 324 Chapter 7 Configure Switch Features Table 85 - PoE Fields Field Description Power over Ethernet (PoE) Port Configuration Port Displays the port number. Mode Displays the Power Management mode of the port: • Auto—Enables the detection of powered devices and automatically allocates power to the PoE port if a device is connected. This setting is selected by default.
Page 325: Resilient Ethernet Protocol (Rep)
Configure Switch Features Chapter 7 Resilient Ethernet Protocol REP provides an alternative to Spanning Tree Protocol (STP) to control network rings and loops, handle link failures, and improve convergence time. (REP) REP controls a group of ports that are connected in a segment, makes sure that the segment does not create any bridging loops, and responds to link failures within the segment.
Page 326: Rep Open Segment
Chapter 7 Configure Switch Features REP and STP can coexist on the same switch, but not on the same port. REP does not interact with STP. For example, if a port is configured as an REP port, STP is disabled on that port. STP bridge protocol data units (BPDUs) are not accepted on or sent from REP ports.
Page 327: Rep Ring Segment
Configure Switch Features Chapter 7 REP Ring Segment The segment that is shown in Figure 44, with both edge ports on the same switch, is a ring segment. In this configuration, there is connectivity between the edge ports through the segment. With this configuration, you can create a redundant connection between any two switches in the segment.
Page 328: Link Integrity
Chapter 7 Configure Switch Features In the example that is shown in Figure 45, E1 or E2 can be configured as the primary no-neighbor port. Figure 45 - Ring Topology Example REP Not Supported REP Ports Configured at Transit Ports REP has these limitations: •...
Page 329: Configure Rep Via Device Manager
Configure Switch Features Chapter 7 Configure REP via Device Manager From the Configure menu, choose REP. To create a REP segment, set a segment ID and port type for a switch port. Table 86 - REP Fields Field Description REP Admin VLAN The administrative VLAN.
Page 330: Layer 3 Routing
TCNs are used within the segment to notify REP neighbors of topology changes. At the edge of the segment, REP can propagate the notification to the STP or to the other REP segments. Stratix 8300 and Stratix 5400 and Stratix 5410 Layer 3 firmware models use Layer 3 Routing IP address routing to map subnetworks (subnets) to an individual VLAN.
Page 331: Types Of Routing
Configure Switch Features Chapter 7 Types of Routing Stratix 8300 and Stratix 5400 and Stratix 5410 Layer 3 firmware models can route packets by using these methods. Table 87 - Layer 3 Routing Feature Description Enhanced Interior Gateway Routing Protocol Enhanced Interior Gateway Routing Protocol (EIGRP) on page 332.
Page 332: Enhanced Interior Gateway Routing Protocol (Eigrp)
Chapter 7 Configure Switch Features Enhanced Interior Gateway EIGRP is available on Stratix 8300 switches and Stratix 5400 and 5410 switches with Layer 3 firmware. Routing Protocol (EIGRP) EIGRP is a Cisco proprietary, distance-vector-routing protocol. Key capabilities that distinguish EIGRP from other routing protocols include fast convergence, support for variable-length subnet mask, support for partial updates, and support for multiple network layer protocols.
Page 333: Configure Eigrp Via Device Manager
Configure Switch Features Chapter 7 EIGRP via Device Manager Configure From the Configure menu, choose EIGRP. Table 88 - EIGRP Fields Field Description EIRGP Instances—Add EIGRP instances to the EIGRP table. To customize the default settings for an instance, see page 336.
Page 334 Chapter 7 Configure Switch Features Table 88 - EIGRP Fields (continued) Field Description Enable Split Horizon Check the checkbox to enable split horizon on the interface. Split horizon controls the sending of EIGRP update and query packets. When split horizon is enabled on an interface, update and query packets are not sent to destinations for which this interface is the next hop. Controlling update and query packets in this manner reduces the possibility of routing loops.
Page 335 Configure Switch Features Chapter 7 Table 88 - EIGRP Fields (continued) Field Description Static Neighbor—EIGRP hello packets are sent as multicast packets. If an EIGRP neighbor is located across a nonbroadcast network, such as a tunnel, you must manually define that neighbor.
Page 336 Chapter 7 Configure Switch Features Table 89 - Customize EIGRP Parameters Field Description EIGRP ID (Not editable). Displays the Autonomous System (AS) number of the EIGRP routing process. Auto-Summary Check the checkbox to allow the automatic summarization of subnet routes into network-level routes. This feature is disabled by default (the software sends subprefix routing information across classful network boundaries).
Page 337: Open Shortest Path First (Ospf)
Auto-Summary feature. Default: Disabled Open Shortest Path First OSPF is available on Stratix 8300 switches and Stratix 5400 and 5410 switches with Layer 3 firmware. (OSPF) OSPF is an interior gateway routing protocol that uses link states rather than distance vectors for path selection.
Page 338 Chapter 7 Configure Switch Features The OSPF implementation on the switch conforms to the OSPF Version 2 specifications with support for these key features: • Definition of stub areas. • Routes that are learned through any IP routing protocol can be redistributed into another IP routing protocol.
Page 339: Configure Ospf Via Device Manager
Configure Switch Features Chapter 7 OSPF via Device Manager Configure From the Configure menu, choose OSPF. Table 90 - OSPF Fields Field Description OSPF Instances—Add OSPF instances to the OSPF table. To customize the default settings for an instance, see page 342.
Page 340 Chapter 7 Configure Switch Features Table 90 - OSPF Fields (continued) Field Description Route Summarization—Route summarization consolidates and summarizes addresses for an area and is used only with area border routers (ABRs). In OSPF, an ABR advertises networks in one area into another area. If the network numbers in an area are contiguous, you can configure the ABR to advertise a summary route that covers all individual networks within the area that are in the specified range.
Page 341 Configure Switch Features Chapter 7 Table 90 - OSPF Fields (continued) Field Description Summary Address—An OSPF ASBR uses a summary address to advertise one external route as an aggregate for all redistributed routes that are covered by the address. OSPF ID Choose an OSPF routing process ID.
Page 342 Chapter 7 Configure Switch Features To change the default settings after adding an EIGRP instance, on the EIGRP Instances tab, click the button in the row to customize, and then click Customize Default Settings. IMPORTANT Setting metrics is complex and is not recommended without guidance from an experienced network designer.
Page 343 Configure Switch Features Chapter 7 Table 91 - Customize OSPF Parameters (continued) Field Description Flood Pacing Type the time at which LSAs in the flooding queue are paced between updates. Valid values: 5…100 ms Default: 33 ms The default settings for OSPF packet pacing timers are suitable for most OSPF deployments. Do not change the packet pacing timers unless all other options to meet OSPF packet flooding requirements have been exhausted.
Page 344: Static And Connected Routing
Chapter 7 Configure Switch Features Static and Connected The switch supports these forms of routing: Routing • Static routing—Defines explicit paths between two devices (routers and switches). You must manually define the route information, including the destination IP address, destination subnet mask, and next hop router IP address.
Page 345: Reallocate Switch Memory For Routing Via Device Manager
Configure Switch Features Chapter 7 Reallocate Switch Memory for Routing via Device Manager Switch Management Database (SDM) templates optimize how switch memory is allocated for specific features, such as routing. To enable routing, you must change the default SDM template to the Lanbase Routing template. To apply an SDM template, follow these steps.
Page 346: Enable And Configure Routing Via Device Manager
Chapter 7 Configure Switch Features Enable and Configure Routing via Device Manager Before you can enable routing, you must reallocate switch memory for routing, as described on page 345. From the Configure menu, choose Routing. From the Routing window, you can enable connected routing only or both static and connected routing.
Page 347: Simple Network Management Protocol (Snmp)
Configure Switch Features Chapter 7 Simple Network The switch supports SNMP versions 1, 2C, and 3. SNMP enables the switch to be remotely managed through other network management software. This Management Protocol feature is disabled by default. (SNMP) SNMP is based on three concepts: •...
Page 348: Supported Mibs
Chapter 7 Configure Switch Features Supported MIBs Stratix managed switches support the following MIBs. Table 92 - Supported MIBs MIB Name BRIDGE-MIB CISCO-MEMORY-POOL-MIB IP-MIB CALISTA-DPA-MIB CISCO-PAE-MIB LLDP-EXT-MED-MIB CISCO-ACCESS-ENVMON-MIB CISCO-PAGP-MIB LLDP-MIB CISCO-ADMISSION-POLICY-MIB CISCO-PING-MIB NETRANGER CISCO-AUTH-FRAMEWORK-MIB CISCO-PORT-QOS-MIB NOTIFICATION-LOG-MIB CISCO-BRIDGE-EXT-MIB CISCO-PORT-SECURITY-MIB OLD-CISCO-CHASSIS-MIB CISCO-BULK-FILE-MIB CISCO-PORT-STORM-CONTROL-MIB OLD-CISCO-CPU-MIB CISCO-CABLE-DIAG-MIB...
Page 349: Configure Snmp Via Device Manager
Configure Switch Features Chapter 7 Configure SNMP via Device Manager From the Configure menu, choose SNMP. Community strings are passwords to the switch Management Information Base (MIB). You can create community strings that provide a remote manager read-only or read-write access to the switch. To create, modify, and delete, click the Community Strings tab.
Page 350: Use Snmp Management Applications
Chapter 7 Configure Switch Features Use SNMP Management Applications You can use SNMP management applications such as IntraVue or HP OpenView to configure and manage the switch. Refer to Simple Network Management Protocol (SNMP) on page 347 for more information. Smartports are recommended configurations for the switch ports.
Page 351: Custom Smartport Roles
Configure Switch Features Chapter 7 Table 93 - Smartport Roles (continued) Port Role Description Port Mirroring Apply this role to ports monitored by a network analyzer. For more information about port mirroring, see page 301. None Apply this role to ports if you do not want a specialized Smartport role on the port. This role can be used on connections to any device, including devices with other Smartport roles.
Page 352: Configure Smartports Via Device Manager
Chapter 7 Configure Switch Features Configure Smartports via Device Manager From the Configure menu, choose Smartports. Follow these guidelines when using Smartport roles: • Before using Smartport roles, decide which switch port is connected to which device type. • Before attaching a device to the port or reconnecting devices that have been moved, verify which Smartport role is applied to a port.
Page 353: Customize Port Role Attributes
Configure Switch Features Chapter 7 Customize Port Role Attributes Each switch port is a member of a VLAN. Devices that are attached to switch ports that belong to the same VLAN share data broadcasts and system resources. Depending on your network requirements, it can be sufficient to assign all ports to the default VLAN, which is named default.
Page 354: Manage Custom Smartport Macros
Chapter 7 Configure Switch Features 4. Modify the VLAN assignments as needed: • For ports applied with the Automation Device with QoS, Switch For Automation, Router For Automation, or Wireless For Automation port role, choose a VLAN from the Native VLAN list. •...
Page 355 Configure Switch Features Chapter 7 5. Enter a macro definition. The definition can contain up to 3000 characters. Enter the macro commands with one command per line. Use the # character at the beginning of a line to enter comment text within the macro. Available parameters for the macro are $native_vlan, $access_vlan, and $voice_vlan.
Page 356 Chapter 7 Configure Switch Features 4. Click Edit. 5. Change the definitions as needed. 6. Click Submit. Delete a Custom Smartports Macro You cannot delete a custom Smartports macro that is currently in use. 1. From the Configure menu, choose Smartports. 2.
Page 357 Configure Switch Features Chapter 7 Import a Custom Smartports Macro 1. From the Configure menu, choose Smartports. 2. Click the Custom Smartports tab. 3. Click Import. 4. Click Browse. 5. Select the macro file on your computer or network drive. The file must be an appropriately formatted .xml file.
Page 358: Assign Smartports And Vlans Via The Logix Designer Application
Chapter 7 Configure Switch Features Export a Custom Smartports Macro 1. From the Configure menu, choose Smartports. 2. Click the Custom Smartports tab. 3. Check the checkbox next to the macro to export. 4. Click Export. 5. Save the resulting file. Assign Smartports and VLANs via the Logix Designer Application In the navigation pane, click Smartports &...
Page 359 Configure Switch Features Chapter 7 Figure 47 - Smartport & VLAN Assignment Rockwell Automation Publication 1783-UM007G-EN-P - February 2017...
Page 360 Chapter 7 Configure Switch Features For Stratix 8000/8300 switches, in the navigation pane, click Advanced Port Configuration. Figure 48 - Advanced Port Configuration for Stratix 8000/8300 Switches Table 94 - Smartport and VLAN Assignment Fields Field Description Unit Indicates where the port resides: •...
Page 361: Spanning Tree Protocol (Stp)
Configure Switch Features Chapter 7 Spanning Tree Protocol (STP) STP is a Layer 2 link management protocol that provides path redundancy while preventing loops in the network. For a Layer 2 Ethernet network to function properly, only one active path can exist between any two stations. Multiple active paths among end stations cause loops in the network.
Page 362: Configure Stp Via Device Manager
Chapter 7 Configure Switch Features Spanning Tree Protocol (STP) modes include the following: • Multiple Spanning Tree (MST) prevents network loops by enabling only one active path for traffic. MST also provides a redundant path if the active path becomes unavailable. This is the default STP mode. If you connect the switch to a Cisco network switch, the typical default is PVST+, not MST.
Page 363 Configure Switch Features Chapter 7 PortFast Settings To enable PortFast and related features, click the PortFast tab. On the PortFast tab, you can change the way that STP is implemented on individual ports. PortFast features are typically enabled only on access ports. Access ports connect to devices such as personal computers, access points, and servers that are not expected to send bridge protocol data units (BPDUs).
Page 364: Configure Stp Via The Logix Designer Application
• Per VLAN Spanning Tree Plus (PVST+) • Rapid Per-VLAN Spanning Tree (RPVST+) MST/RSTP is the default. Figure 49 - Switch Configuration for Stratix 5400, Stratix 5410, Stratix 5700, and ArmorStratix 5700 Switches Rockwell Automation Publication 1783-UM007G-EN-P - February 2017...
Page 365: Virtual Local Area Networks (Vlans)
Configure Switch Features Chapter 7 Virtual Local Area Networks A VLAN is a logical segment of network users and resources grouped by function, team, or application. This segmentation is without regard to the (VLANs) physical location of the users and resources. For example, VLANs can be based on the departments in your company or by sets of users who communicate mostly with each other.
Page 366: Isolate Traffic And Users
Chapter 7 Configure Switch Features Isolate Traffic and Users By using VLANs, you can isolate different types of traffic, such as voice and data. Isolating different types of traffic helps to preserve the quality of the transmission and to minimize excess traffic among the logical segments. You can also use VLANs to isolate different types of users.
Page 367: Isolate Different Traffic Types
Configure Switch Features Chapter 7 Isolate Different Traffic Types Isolating data traffic from delay-sensitive traffic, such as voice traffic, increases the quality of the voice transmission. In Figure 50, switch ports that are connected to the IP phones belong to VLAN 3, a VLAN that is configured to provide Voice over IP (VoIP) services on these connections, meaning priority is given to voice traffic over regular IP data traffic.
Page 368: Configure Vlans Via Device Manager
Chapter 7 Configure Switch Features Configure VLANs via Device Manager From the Configure menu, choose VLAN Management. You can add, edit, and delete VLANs. To assign ports to VLANs, use the Edit Physical Ports window, as described on page 51. Before you assign ports to VLANs, make sure that each port has the appropriate port role.
Page 369: Configure Vlans Via The Logix Designer Application
In the navigation pane, click Smarports & VLANs. In the VLAN Configuration area, you can add, edit, and delete VLANs. Figure 51 - VLAN Configuration for Stratix 5400, Stratix 5410, Stratix 5700, and ArmorStratix 5700 Switches To assign ports to VLANs, see...
Page 370 Chapter 7 Configure Switch Features Rockwell Automation Publication 1783-UM007G-EN-P - February 2017...
Page 371: Monitor The Switch
Chapter Monitor the Switch Topic Page Switch Status via Device Manager Switch Status via the Logix Designer Application System Log Messages Trends Port Statistics NAT Statistics REP Status CIP Status DHCP Clients DLR Status PRP Status Port Diagnostics Cable Diagnostics DHCP Pool Display Rockwell Automation Publication 1783-UM007G-EN-P - February 2017...
Page 372: Switch Status Via Device Manager
Chapter 8 Monitor the Switch Switch Status via The Dashboard window in Device Manager lets you monitor switch status and performance. Device Manager The Dashboard window is similar to the Monitor > Trends window. The Dashboard window displays the instantaneous status while the Trends window displays the historical status.
Page 373: Front Panel
Monitor the Switch Chapter 8 Front Panel The Front Panel view on the dashboard is a graphical display of the switch front panel. The switch components on the front panel view are color-coded by status. The status indicators on the view in Device Manager match the status indicators on the physical switch: •...
Page 374 Chapter 8 Monitor the Switch You can identify the physical switch in the group of similar devices by checking the Locate Switch checkbox on the Front Panel view. Figure 55 - Locate Switch Checkbox When you check the Locate Switch checkbox, the system status indicators on the physical switch (Setup, EIP NET, EIP Mod, Alarm) flash green to visually notify you that the feature is enabled.
Page 375 Monitor the Switch Chapter 8 Table 95 - Stratix 5700 and ArmorStratix 5700 System Status Indicators Indicator Status Description Setup The Setup status indicator shows the status of the initial setup of the switch. The behavior of the Setup status indicator varies depending on whether you run single-mode or multi-mode Express Setup. In multi-mode Express Setup, the behavior varies based on whether you run Short Press, Medium Press, or Long Press mode.
Page 376 Chapter 8 Monitor the Switch Table 96 - Stratix 5700 and ArmorStratix 5700 Port Status Indicators (continued) Mode Status Description No link present on the port. Solid green Port link; no activity. Flashing green and off Link is active and healthy. Alternating green and There is a fault or error on the link.
Page 377 Chapter 8 Stratix 5400 Front Panel In addition to the View modes on the Dashboard window, the Stratix 5400 switch has a Display Mode button on the physical switch. The Display Mode button changes the behavior of the port status indicators based on the selected mode.
Page 378 Chapter 8 Monitor the Switch Table 97 - Stratix 5400 System Status Indicators Indicator Status Description Setup The Setup status indicator shows the status of the initial setup of the switch.The Setup status indicator shows the status of the initial setup of the switch.
Page 379 Monitor the Switch Chapter 8 Table 98 - Stratix 5400 Port Status Indicators Mode Status Description Status In Status mode, the port status indicators show the connection and activity status of the port. Status mode is the default mode. You can choose Status mode via the View pull-down menu in Device Manager.
Page 380 Chapter 8 Monitor the Switch Stratix 5410 Front Panel In addition to the View modes on the Dashboard window, the Stratix 5410 switch has a Disp. Mode button on the physical switch that changes the behavior of the port status indicators based on the selected mode. Select a mode by pressing the Disp.
Page 381 Monitor the Switch Chapter 8 Table 99 - Stratix 5410 System Status Indicators Indicator Status Description EIP Mod The EIP Mod status indicator shows the status of the switch. Power to the switch is off or is not properly connected. Solid green The switch is operating properly.
Page 382 Chapter 8 Monitor the Switch Table 100 - Stratix 5410 Port Status Indicators Mode Status Description Status In Status mode, the port status indicators show the connection and activity status of the port. Status mode is the default mode. You can choose Status mode via the View pull-down menu in Device Manager.
Page 383 Monitor the Switch Chapter 8 Stratix 8000/8300 Front Panel Table 101 - Stratix 8000/8300 System Status Indicators Indicator Status Description EIP Mod The EIP Mod status indicator shows the status of the switch. Power to the switch is off or is not properly connected. Solid green The switch is operating properly.
Page 384 Chapter 8 Monitor the Switch Table 102 - Stratix 8000/8300 Port Status Indicators Mode Status Description Status In Status mode, the port status indicators show the status of the ports. Status is the default mode. No link Solid green No activity on link. Flashing green Link activity.
Page 385: Switch Information
Monitor the Switch Chapter 8 Switch Information The Switch Information area on the Dashboard displays information about the switch. Table 103 - Switch Information Fields Field Description Host Name A descriptive name for this switch. The default name is Switch. You can set this parameter on the Admin > Express Setup window. IP Address The IP address of this switch.
Page 386: Switch Health
Chapter 8 Monitor the Switch Switch Health You can use the health gauges to monitor CPU utilization and temperature. The CPU Utilization gauge shows the percentage of CPU processing power that is in use on the switch. Data is collected at each 60-second system refresh. The gauge changes as the switch experiences the network activity from devices sending data through the network.
Page 387: Port Utilization
Monitor the Switch Chapter 8 Port Utilization You can choose which types of network traffic to display and in what format: • Types of traffic—By default, all traffic is displayed for all interfaces. Click the links above the display area to display all traffic, errors, received traffic, or transmitted traffic.
Page 388: Switch Status Via The Logix Designer Application
Chapter 8 Monitor the Switch Switch Status via the Logix The Switch Status view in the Studio 5000 Logix Designer® application lets you view status parameters for the switch. Designer Application In the navigation pane, click Switch Status. Table 104 - Switch Status Fields Field Description Alarms &...
Page 389 Monitor the Switch Chapter 8 Table 104 - Switch Status Fields (continued) Field Description SD Card Present Displays whether the SD card is installed. Power Power Present on Terminal A Displays a yes or no value to indicate whether power is present on Terminal A. Power Present on Terminal B Displays a yes or no value to indicate whether power is present on Terminal B.
Page 390 Chapter 8 Monitor the Switch You can also monitor the switch status on the Module Info view. Table 105 - Module Info Fields Field Description Identification Displays the following switch information: • Vendor • Product type • Product code • Revision •...
Page 391: Port Status
Monitor the Switch Chapter 8 Port Status In the navigation pane, click Port Status. You can monitor alarms, statuses, thresholds, and bandwidth utilization for each switch port. You can also access port and cable diagnostics. Table 106 - Port Status Fields Field Description Unit...
Page 392: System Log Messages
Chapter 8 Monitor the Switch Table 106 - Port Status Fields (continued) Field Description Threshold Exceeded Displays unusual changes for these types of network traffic: • Unicast—Displays a yes or no value to indicate whether the current unicast traffic has exceeded the threshold value. •...
Page 393 Monitor the Switch Chapter 8 To filter historical events, choose a severity filter or type filter: • Debugging—Debug messages. • Informational—Informational messages. • Notifications—The switch is operating normally but has a significant condition. • Warnings—The switch has a warning condition. •...
Page 394: Trends
Chapter 8 Monitor the Switch Trends In Device Manager, you can view historical data to help you to analyze traffic patterns and to identify problems. Data can be displayed in increments of seconds, minutes, hours, or days. To view the data in a table, click the Grid Mode button below the area. To display a chart, click the Chart Mode button.
Page 395: Port Statistics
Monitor the Switch Chapter 8 Port Statistics In Device Manager, you can view statistics for data that passes through the switch ports. From the Monitor menu, choose Port Statistics. For more information, see the online help for Device Manager. The types of port statistics are grouped under these tabs on the Port Statistics window: •...
Page 396: Nat Statistics
• Statistics per instance • Detailed private translations per instance • Detailed public translations per instance From the Monitor menu, choose NAT Statistics. Figure 58 - NAT Statistics for Stratix 5400 and 5700 Switches Rockwell Automation Publication 1783-UM007G-EN-P - February 2017...
Page 397 Monitor the Switch Chapter 8 Figure 59 - NAT Statistics for Stratix 5410 Rockwell Automation Publication 1783-UM007G-EN-P - February 2017...
Page 398 Monitor the Switch Table 109 - NAT Statistics Field Description Global Statistic s for Stratix 5400 and 5700 Switches Current Active Translations The number of IP addresses that have been translated within the last 90 seconds across all NAT instances. Total Translations The total number of translations across all NAT instances.
Page 399: Monitor Nat Statistics Via The Logix Designer Application
Monitor the Switch Chapter 8 Monitor NAT Statistics via the Logix Designer Application For each NAT instance, you can monitor these diagnostics: • Diagnostics for both private and public translations • Diagnostics for only private translations • Diagnostics for only public translations In the navigation pane, click NAT, and then click the ellipse in the Diagnostics column.
Page 400 Chapter 8 Monitor the Switch Table 110 - NAT Diagnostics per Instance Field Description Current Active Translations Displays the number of translations that have occurred within the last 90 seconds across all NAT instances. Total NAT Translated Packets Displays the total number of packets that have been translated for this instance. Total Private to Public Address Translations Displays the total number of private-to-public translations for this instance.
Page 401: Private-To-Public Translation Diagnostics
Monitor the Switch Chapter 8 Private-to-Public Translation Diagnostics From the Private to Public Translations dialog box for an instance, you can view a list of IP addresses that have been changed by NAT within the last 90 seconds. Table 111 - Private-to-Public Translation Diagnostics Field Description Private...
Page 402: Public-To-Private Translation Diagnostics
Chapter 8 Monitor the Switch Public-to-Private Translation Diagnostics From the Public to Private Translations dialog box for an instance, you can view a list of IP addresses that have been changed by NAT within the last 90 seconds. Table 112 - Public-to-Private Translation Diagnostics Field Description Public...
Page 403: Rep Status
Monitor the Switch Chapter 8 REP Status In Device Manager, you can review the status of the REP topology for one or all network segments. From the Monitor menu, choose REP. To display an archived REP topology, click the Archived Topology tab and then select the segment ID.
Page 404 Chapter 8 Monitor the Switch From the Monitor menu, choose CIP Status. Table 113 - CIP Status Fields Field Description Overview State The state of the CIP connection (Enabled or Disabled). Vlan The VLAN ID. CIP I/O Connection Owner The IP address of the device to and from which application-specific I/O output data is sent and received. CIP Config Session Owner The IP address of the device controlling the CIP configuration session.
Page 405: Dhcp Clients
Monitor the Switch Chapter 8 DHCP Clients In Device Manager, you can view information about devices connected to a switch with DHCP snooping enabled. These devices are known as DHCP clients. The DHCP snooping feature dynamically builds and maintains entries in the DHCP Clients table shown below.
Page 406: Dlr Status
Logix Designer application. Configuration parameters appear for the number of available rings: • Stratix 5700 and ArmorStratix™ 5700 switches show one ring. • Stratix 5400 switches show three rings. For more information about DLR troubleshooting, see Troubleshoot EtherNet/IP Networks, publication ENET-AT003.
Page 407 Monitor the Switch Chapter 8 Rockwell Automation Publication 1783-UM007G-EN-P - February 2017...
Page 408: Monitor Dlr Status Via The Logix Designer Application
Chapter 8 Monitor the Switch Monitor DLR Status via the Logix Designer Application From the navigation pane, expand Device Level Ring (DLR), expand Ring 1, Ring 2, or Ring 3, and then click one of the following: • To view the status and parameters that are configured for the switch, the redundant gateway, and the active ring supervisor, click Statistics.
Page 409 Monitor the Switch Chapter 8 Rockwell Automation Publication 1783-UM007G-EN-P - February 2017...
Page 410: Prp Status
For more information about PRP, see the following: • Parallel Redundancy Protocol (PRP) on page 297. • Stratix 5400 Display Modes on page 377 • Stratix 5410 Display Modes on page 380 From the Monitor menu, choose PRP. Table 115 - VDAN Table Fields...
Page 411 Monitor the Switch Chapter 8 Table 116 - Node Table Fields Field Description Channel Group 1, 2 The number of the PRP channel group. MAC Address The number of MAC addresses (static and dynamic) for the channel group. The number of dual attached node (DAN) MAC addresses for the channel group. SAN-A The number of single attached nodes (SANs) on LAN A.
Page 412: Port Diagnostics
Chapter 8 Monitor the Switch Port Diagnostics The Port Diagnostics feature in the Logix Designer application lets you view the status of the link performance: • View octet and packet counters • View collisions on the link • View errors on the link You can also reset and clear all status counters.
Page 413 Monitor the Switch Chapter 8 Table 117 - Port Diagnostics Fields Field Description Unit Indicates where the port resides: • Base (for example, 1783-MS10T). (Stratix 8000/8300 switches) • Expansion module (for example, 1783-MX08T). Port The port that is selected for configuration. The port number includes the port type (Fa for Fast Ethernet and Gi for Gigabit Ethernet), the base or expansion module for Stratix 8000/8300 switches, and the specific port number.
Page 414: Cable Diagnostics
Chapter 8 Monitor the Switch Cable Diagnostics The Cable Diagnostics feature lets you run a test on each switch port to determine the integrity of the cable that is connected to the RJ45 (copper) ports. The test determines the distance to the break from the switch for each cable with a plus or minus error value individually listed.
Page 415: Diagnose Cables Via The Logix Designer Application
Monitor the Switch Chapter 8 Diagnose Cables via the Logix Designer Application In the navigation pane, click Port Status, and then click the button in the Cable Diagnostics column for the corresponding port. Table 118 - Cable Diagnostics Fields Field Description Port The port that is selected for configuration.
Page 416: Dhcp Pool Display
Chapter 8 Monitor the Switch DHCP Pool Display In the Logix Designer application, you can view DHCP address pool information for the switch. You can view 0…15 pools. This information is gathered directly from the switch. Each row represents one instance, and instance values cannot be consecutive.
Page 417: Troubleshoot The Switch
Chapter Troubleshoot the Switch Topic Page Troubleshoot the Installation Verify Boot Fast Troubleshoot IP Addresses Troubleshoot Device Manager Troubleshoot Switch Performance Access Direct Managed Mode Restart or Reset the Switch Recover the Switch Firmware Troubleshoot a Firmware Update Collect System and Configuration Information for Technical Support This chapter helps you resolve issues that are related to Stratix®...
Page 418: Troubleshoot The Installation
Chapter 9 Troubleshoot the Switch Troubleshoot the Installation The status indicators on the front panel provide troubleshooting information about the switch. They show power-on self-test (POST) failures, port connectivity problems, and overall switch performance. You can also get statistics from the browser interface, the command-line interface (CLI), or a Simple Network Management Protocol (SNMP) workstation.
Page 419: Bad Or Damaged Cable
Troubleshoot the Switch Chapter 9 Bad or Damaged Cable Always make sure that the cable does not have marginal damage or failure. Even if a cable can connect at the physical layer, subtle damage to the wiring or connectors can corrupt packets. This situation is likely when the port has many packet errors or the port constantly loses and regains the link.
Page 420: Link Status
Chapter 9 Troubleshoot the Switch Link Status Verify that both sides have a network link. A broken wire or one shut down port can cause one side to show a link, but not the other side. A Link status indicator does not indicate that the cable is fully functional. The cable can encounter physical stress that causes it to function at a marginal level.
Page 421: Verify Boot Fast
Troubleshoot the Switch Chapter 9 Verify Boot Fast Boot Fast failures are potentially fatal to the switch. Contact your Rockwell Automation representative if your switch does not successfully complete Boot Fast. You can disable Boot Fast and run a power-on self-test (POST) by using the CLI.
Page 422: Troubleshoot Switch Performance
Chapter 9 Troubleshoot the Switch Troubleshoot Switch The following table includes basic troubleshooting for issues that are related to switch performance. Performance Issue Resolution Speed, duplex, and autonegotiation Port statistics that show a large amount of alignment errors, frame check sequence (FCS), or late-collisions errors can indicate a speed or duplex mismatch.
Page 423: Access Direct Managed Mode
Troubleshoot the Switch Chapter 9 Access Direct Managed Mode You can display Device Manager and manage the switch through a physical connection between one of the switch ports and your computer or laptop. This type of management connection is referred to as Direct Managed mode. This mode is typically used to connect to the switch by using Device Manager when the IP address of the switch is unknown.
Page 424: Restart Or Reset The Switch
Chapter 9 Troubleshoot the Switch Restart or Reset the Switch If you cannot solve an issue by reconfiguring a feature, you can restart or reset the switch to solve the issue. If the issue exists after you reset the switch to its default settings, it is unlikely that the switch is causing the issue.
Page 425: Reset The Switch Via The Express Setup Button
16…20, and then release. See also Run Multi-mode Express Setup in Long Press Mode on page 15.2(4)EA or earlier Stratix 5400, 5410, 5700, Follow these steps. or ArmorStratix™ 5700 1. Make sure that the switch is fully powered up. 2. Press and hold the Express Setup button for 10 seconds until the EIP Mod status indicator turns red, and then immediately release the Express Setup button.
Page 426: Recover The Switch Firmware
Chapter 9 Troubleshoot the Switch Recover the Switch Firmware Before you can recover switch firmware, make sure of the following: • You have physical access to the switch. • At least one switch port is enabled and is not connected to a device. You can recover the switch firmware if needed, such as in these scenarios: •...
Page 427: Collect System And Configuration Information For Technical Support
Troubleshoot the Switch Chapter 9 Collect System and The Device Manager online Help provides a link that you can use to collect system and configuration information about the switch. When you click the Configuration Information link, the switch runs the show tech-support command via the command-line for Technical Support interface (CLI).
Page 428 Chapter 9 Troubleshoot the Switch Notes: Rockwell Automation Publication 1783-UM007G-EN-P - February 2017...
Page 429: Data Types
Appendix Data Types Topic Page Stratix 5400 Data Types Stratix 5410 Data Types Stratix 5700 and ArmorStratix 5700 Data Types Stratix 8000 and 8300 Data Types In the Studio 5000 Logix Designer® application, predefined tags for Input and Output data types have a structure that corresponds to the switch selected when it was added to the I/O tree.
Page 430: Stratix 5400 Data Types
Appendix A Data Types Stratix 5400 Data Types The following tables list module-defined data types for Stratix® 5400 switches. The tables include information for input (I) and output (O). 8-port Switches Catalog number 1783-HMS4C4CGN Table 121 - Input Data Types (8-port switches)
Page 431 Data Types Appendix A Table 121 - Input Data Types (8-port switches) (continued) AB:STRATIX_5400_8PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortGi1_3Utilization SINT Decimal PortGi1_4Utilization SINT Decimal PortFa1_5Utilization SINT Decimal PortFa1_6Utilization SINT Decimal PortFa1_7Utilization SINT Decimal PortFa1_8Utilization SINT Decimal MajorAlarmRelay BOOL Decimal...
Page 432: 12-Port Switches
Appendix A Data Types 12-port Switches Catalog numbers 1783-HMS8T4CGN,1783-HMS8S4CGN, 1783-HMS4T4E4CGN Table 123 - Input Data Types (12-port switches) AB:STRATIX_5400_12PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style Fault DINT Binary AnyPortConnected BOOL Decimal LinkStatus:0 PortGi1_1Connected BOOL Decimal LinkStatus:1 PortGi1_2Connected BOOL Decimal LinkStatus:2 PortGi1_3Connected...
Page 433 Data Types Appendix A Table 123 - Input Data Types (12-port switches) (continued) AB:STRATIX_5400_12PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortFa1_7Threshold BOOL Decimal ThresholdExceeded:7 PortFa1_8Threshold BOOL Decimal ThresholdExceeded:8 PortFa1_9Threshold BOOL Decimal ThresholdExceeded:9 PortFa1_10Threshold BOOL Decimal ThresholdExceeded:10 PortFa1_11Threshold BOOL Decimal ThresholdExceeded:11 PortFa1_12Threshold...
Page 434: 12-Port Gigabit Switches
Appendix A Data Types Table 124 - Output Data Type (12-port switches) (continued) AB:STRATIX_5400_12PORT_MANAGED:O:0 Member Name Type Default Display Valid Values Style PortFa1_10Disable BOOL Decimal DisablePort:10 PortFa1_11Disable BOOL Decimal DisablePort:11 PortFa1_12Disable BOOL Decimal DisablePort:12 12-port Gigabit Switches Catalog numbers 1783-HMS8TG4CGN, 1783-HMS8SG4CGN, 1783-HMS4EG8CGN, 1783-HMS8TG4CGR, 1783-HMS8SG4CGR, 1783-HMS4EG8CGR Table 125 - Input Data Types (12-port Gb switches)
Page 435 Data Types Appendix A Table 125 - Input Data Types (12-port Gb switches) (continued) AB:STRATIX_5400_12PORT_GB_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortGi1_11UnauthorizedDevice BOOL Decimal UnauthorizedDevice:11 PortGi1_12UnauthorizedDevice BOOL Decimal UnauthorizedDevice:12 AnyPortThreshold BOOL Decimal ThresholdExceeded:0 PortGi1_1Threshold BOOL Decimal ThresholdExceeded:1 PortGi1_2Threshold BOOL Decimal ThresholdExceeded:2...
Page 436: 16-Port Switches
Appendix A Data Types Table 126 - Output Data Type (12-port Gb switches) AB:STRATIX_5400_12PORT_GB_MANAGED:O:0 Member Name Type Default Display Valid Values Style AllPortsDisabled BOOL Decimal DisablePort:0 PortGi1_1Disable BOOL Decimal DisablePort:1 PortGi1_2Disable BOOL Decimal DisablePort:2 PortGi1_3Disable BOOL Decimal DisablePort:3 PortGi1_4Disable BOOL Decimal DisablePort:4 PortGi1_5Disable...
Page 437 Data Types Appendix A Table 127 - Input Data Type (16-port switches) (continued) AB:STRATIX_5400_16PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortFa1_15Connected BOOL Decimal LinkStatus:15 PortFa1_16Connected BOOL Decimal LinkStatus:16 AnyPortUnauthorizedDevice BOOL Decimal UnauthorizedDevice:0 PortGi1_1UnauthorizedDevice BOOL Decimal UnauthorizedDevice:1 PortGi1_2UnauthorizedDevice BOOL Decimal UnauthorizedDevice:2 PortGi1_3UnauthorizedDevice...
Page 438 Appendix A Data Types Table 127 - Input Data Type (16-port switches) (continued) AB:STRATIX_5400_16PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortGi1_2Utilization SINT Decimal PortGi1_3Utilization SINT Decimal PortGi1_4Utilization SINT Decimal PortFa1_5Utilization SINT Decimal PortFa1_6Utilization SINT Decimal PortFa1_7Utilization SINT Decimal PortFa1_8Utilization SINT Decimal...
Page 439: 16-Port Gigabit Switches
Data Types Appendix A Table 128 - Output Data Type (16-port switches) (continued) AB:STRATIX_5400_16PORT_MANAGED:O:0 Member Name Type Default Display Valid Values Style PortFa1_14Disable BOOL Decimal DisablePort:14 PortFa1_15Disable BOOL Decimal DisablePort:15 PortFa1_16Disable BOOL Decimal DisablePort:16 16-port Gigabit Switches Catalog number 1783-HMS4SG8EG4CGN, 1783-HMS4SG8EG4CGR Table 129 - Input Data Type (16-port Gb switches) AB:STRATIX_5400_16PORT_GB_MANAGED:I:0 Member Name...
Page 440 Appendix A Data Types Table 129 - Input Data Type (16-port Gb switches) (continued) AB:STRATIX_5400_16PORT_GB_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortGi1_8UnauthorizedDevice BOOL Decimal UnauthorizedDevice:8 PortGi1_9UnauthorizedDevice BOOL Decimal UnauthorizedDevice:9 PortGi1_10UnauthorizedDevice BOOL Decimal UnauthorizedDevice:10 PortGi1_11UnauthorizedDevice BOOL Decimal UnauthorizedDevice:11 PortGi1_12UnauthorizedDevice BOOL Decimal UnauthorizedDevice:12...
Page 441 Data Types Appendix A Table 129 - Input Data Type (16-port Gb switches) (continued) AB:STRATIX_5400_16PORT_GB_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortGi1_12Utilization SINT Decimal PortGi1_13Utilization SINT Decimal PortGi1_14Utilization SINT Decimal PortGi1_15Utilization SINT Decimal PortGi1_16Utilization SINT Decimal MajorAlarmRelay BOOL Decimal AlarmRelay:0 MinorAlarmRelay...
Page 442: 20-Port Switches
Appendix A Data Types 20-port Switches Catalog number 1783-HMS16T4CGN Table 131 - Input Data Type (20-port switches) AB:STRATIX_5400_20PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style Fault DINT Binary AnyPortConnected BOOL Decimal LinkStatus:0 PortGi1_1Connected BOOL Decimal LinkStatus:1 PortGi1_2Connected BOOL Decimal LinkStatus:2 PortGi1_3Connected BOOL...
Page 443 Data Types Appendix A Table 131 - Input Data Type (20-port switches) (continued) AB:STRATIX_5400_20PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortFa1_13UnauthorizedDevice BOOL Decimal UnauthorizedDevice:13 PortFa1_14UnauthorizedDevice BOOL Decimal UnauthorizedDevice:14 PortFa1_15UnauthorizedDevice BOOL Decimal UnauthorizedDevice:15 PortFa1_16UnauthorizedDevice BOOL Decimal UnauthorizedDevice:16 PortFa1_17UnauthorizedDevice BOOL Decimal UnauthorizedDevice:17 PortFa1_18UnauthorizedDevice...
Page 444 Appendix A Data Types Table 131 - Input Data Type (20-port switches) (continued) AB:STRATIX_5400_20PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortFa1_9Utilization SINT Decimal PortFa1_10Utilization SINT Decimal PortFa1_11Utilization SINT Decimal PortFa1_12Utilization SINT Decimal PortFa1_13Utilization SINT Decimal PortFa1_14Utilization SINT Decimal PortFa1_15Utilization SINT Decimal...
Page 445: 20-Port Gigabit Switches
Data Types Appendix A Table 132 - Output Data Type (20-port switches) (continued) AB:STRATIX_5400_20PORT_MANAGED:O:0 Member Name Type Default Display Valid Values Style PortFa1_18Disable BOOL Decimal DisablePort:18 PortFa1_19Disable BOOL Decimal DisablePort:19 PortFa1_20Disable BOOL Decimal DisablePort:20 20-port Gigabit Switches Catalog numbers 1783-HMS16TG4CGN, 1783-HMS8TG8EG4CGN, 1783-HMS16TG4CGR, 1783-HMS8TG8EG4CGR Table 133 - Input Data Type (20-port Gb switches) AB:STRATIX_5400_20PORT_GB_MANAGED:I:0...
Page 446 Appendix A Data Types Table 133 - Input Data Type (20-port Gb switches) (continued) AB:STRATIX_5400_20PORT_GB_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortGi1_4UnauthorizedDevice BOOL Decimal UnauthorizedDevice:4 PortGi1_5UnauthorizedDevice BOOL Decimal UnauthorizedDevice:5 PortGi1_6UnauthorizedDevice BOOL Decimal UnauthorizedDevice:6 PortGi1_7UnauthorizedDevice BOOL Decimal UnauthorizedDevice:7 PortGi1_8UnauthorizedDevice BOOL Decimal UnauthorizedDevice:8...
Page 447 Data Types Appendix A Table 133 - Input Data Type (20-port Gb switches) (continued) AB:STRATIX_5400_20PORT_GB_MANAGED:I:0 Member Name Type Default Display Valid Values Style AllPortsUtilization SINT Decimal PortGi1_1Utilization SINT Decimal PortGi1_2Utilization SINT Decimal PortGi1_3Utilization SINT Decimal PortGi1_4Utilization SINT Decimal PortGi1_5Utilization SINT Decimal PortGi1_6Utilization SINT...
Page 448 Appendix A Data Types Table 134 - Output Data Type (20-Gb port switches) (continued) AB:STRATIX_5400_20PORT_GB_MANAGED:O:0 Member Name Type Default Display Valid Values Style PortGi1_9Disable BOOL Decimal DisablePort:9 PortGi1_10Disable BOOL Decimal DisablePort:10 PortGi1_11Disable BOOL Decimal DisablePort:11 PortGi1_12Disable BOOL Decimal DisablePort:12 PortGi1_13Disable BOOL Decimal DisablePort:13...
Page 449: Stratix 5410 Data Types
Data Types Appendix A Stratix 5410 Data Types The following tables list module-defined data types for Stratix 5410 switches. The tables include information for input (I) and output (O). Table 135 - Input Data Type AB:STRATIX_5410_28PORT_GB_MANAGED:I:0 Member Name Type Default Display Valid Values Style Fault...
Page 450 Appendix A Data Types Table 135 - Input Data Type (continued) AB:STRATIX_5410_28PORT_GB_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortTe1_27Connected BOOL Decimal LinkStatus:27 PortGi1_27Connected PortTe1_28Connected BOOL Decimal LinkStatus:28 PortGi1_28Connected AnyPortUnauthorizedDevice BOOL Decimal UnauthorizedDevice:0 PortGi1_1UnauthorizedDevice BOOL Decimal UnauthorizedDevice:1 PortGi1_2UnauthorizedDevice BOOL Decimal UnauthorizedDevice:2 PortGi1_3UnauthorizedDevice...
Page 451 Data Types Appendix A Table 135 - Input Data Type (continued) AB:STRATIX_5410_28PORT_GB_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortTe1_28UnauthorizedDevice BOOL Decimal UnauthorizedDevice:28 PortGi1_28UnauthorizedDevice AnyPortThreshold BOOL Decimal ThresholdExceeded:0 PortGi1_1Threshold BOOL Decimal ThresholdExceeded:1 PortGi1_2Threshold BOOL Decimal ThresholdExceeded:2 PortGi1_3Threshold BOOL Decimal ThresholdExceeded:3 PortGi1_4Threshold BOOL...
Page 452 Appendix A Data Types Table 135 - Input Data Type (continued) AB:STRATIX_5410_28PORT_GB_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortGi1_1Utilization SINT Decimal PortGi1_2Utilization SINT Decimal PortGi1_3Utilization SINT Decimal PortGi1_4Utilization SINT Decimal PortGi1_5Utilization SINT Decimal PortGi1_6Utilization SINT Decimal PortGi1_7Utilization SINT Decimal PortGi1_8Utilization SINT...
Page 453 Data Types Appendix A Table 136 - Output Data Type AB:STRATIX_5410_28PORT_GB_MANAGED:O:0 Member Name Type Default Display Valid Values Style AllPortsDisabled BOOL Decimal DisablePort:0 PortGi1_1Disable BOOL Decimal DisablePort:1 PortGi1_2Disable BOOL Decimal DisablePort:2 PortGi1_3Disable BOOL Decimal DisablePort:3 PortGi1_4Disable BOOL Decimal DisablePort:4 PortGi1_5Disable BOOL Decimal DisablePort:5...
Page 454: Stratix 5700 And Armorstratix 5700 Data Types
Appendix A Data Types Stratix 5700 and The following tables list module-defined data types for Stratix 5700 and ArmorStratix 5700 switches. The tables include information for input (I) and ArmorStratix 5700 output (O). Data Types 6-port Gb Switches Catalog numbers 1783-BMS4S2SGL, 1783-BMS4S2SGA,1783-BMS06SGL, 1783-BM06SGA, 1783-BMS06TGL, 1783-BMS06TGA Table 137 - Input Data Types (6-port Gb switches) AB:STRATIX_5700_6PORT_GB_MANAGED:I:O...
Page 455: 6-Port Switches
Data Types Appendix A Table 137 - Input Data Types (6-port Gb switches) (continued) AB:STRATIX_5700_6PORT_GB_MANAGED:I:O Member Name Type Default Display Valid Values Style PortGi1_2Utilization SINT Decimal MajorAlarmRelay BOOL Decimal AlarmRelay:0 MulticastGroupsActive DINT Binary Table 138 - Output Data Type (6-port Gb switches) AB:STRATIX_5700_6PORT_GB_MANAGED:O:0 Member Name Type...
Page 456 Appendix A Data Types Table 139 - Input Data Type (6-port switches) (continued) AB:STRATIX_5700_6PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortFa1_6UnauthorizedDevice BOOL Decimal UnauthorizedDevice:6 AnyPortThreshold BOOL Decimal ThresholdExceeded:0 PortFa1_1Threshold BOOL Decimal ThresholdExceeded:1 PortFa1_2Threshold BOOL Decimal ThresholdExceeded:2 PortFa1_3Threshold BOOL Decimal ThresholdExceeded:3 PortFa1_4Threshold...
Page 457: 8-Port Switches
Data Types Appendix A 8-port Switches Catalog number 1783-ZMS8TA Table 141 - Input Data Type (8-port switches) AB:STRATIX_5700_8PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style Fault DINT Binary AnyPortConnected BOOL Decimal LinkStatus:0 PortFa1_1Connected BOOL Decimal LinkStatus:1 PortFa1_2Connected BOOL Decimal LinkStatus:2 PortFa1_3Connected BOOL...
Page 458: 10-Port Gb Switches
Appendix A Data Types Table 141 - Input Data Type (8-port switches) (continued) AB:STRATIX_5700_8PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortFa1_7Utilization SINT Decimal PortFa1_8Utilization SINT Decimal MajorAlarmRelay BOOL Decimal AlarmRelay:0 MulticastGroupsActive DINT Binary Table 142 - Output Data Type (8-port switches) AB:STRATIX_5700_8PORT_MANAGED:O:0 Member Name Type...
Page 459 Data Types Appendix A Table 143 - Input Data Type (10-port Gb switches) (continued) AB:STRATIX_5700_10PORT_GB_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortGi1_1Connected BOOL Decimal LinkStatus:9 PortGi1_2Connected BOOL Decimal LinkStatus:10 AnyPortUnauthorizedDevice BOOL Decimal UnauthorizedDevice:0 PortFa1_1UnauthorizedDevice BOOL Decimal UnauthorizedDevice:1 PortFa1_2UnauthorizedDevice BOOL Decimal UnauthorizedDevice:2...
Page 460: 10-Port Switches
Appendix A Data Types Table 144 - Output Data Type (10-port Gb switches) AB:STRATIX_5700_10PORT_MANAGED:O:0 Member Name Type Default Display Valid Values Style AllPortsDisabled BOOL Decimal DisablePort:0 PortFa1_1Disable BOOL Decimal DisablePort:1 PortFa1_2Disable BOOL Decimal DisablePort:2 PortFa1_3Disable BOOL Decimal DisablePort:3 PortFa1_4Disable BOOL Decimal DisablePort:4 PortFa1_5Disable...
Page 461 Data Types Appendix A Table 145 - Input Data Type (10-port switches) (continued) AB:STRATIX_5700_10PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortFa1_6UnauthorizedDevice BOOL Decimal UnauthorizedDevice:6 PortFa1_7UnauthorizedDevice BOOL Decimal UnauthorizedDevice:7 PortFa1_8UnauthorizedDevice BOOL Decimal UnauthorizedDevice:8 PortFa1_9UnauthorizedDevice BOOL Decimal UnauthorizedDevice:9 PortFa1_10UnauthorizedDevice BOOL Decimal UnauthorizedDevice:10 AnyPortThreshold...
Page 462: 16-Port Switches
Appendix A Data Types Table 146 - Output Data Type (10-port switches) AB:STRATIX_5700_10PORT_MANAGED:O:0 Member Name Type Default Display Valid Values Style AllPortsDisabled BOOL Decimal DisablePort:0 PortFa1_1Disable BOOL Decimal DisablePort:1 PortFa1_2Disable BOOL Decimal DisablePort:2 PortFa1_3Disable BOOL Decimal DisablePort:3 PortFa1_4Disable BOOL Decimal DisablePort:4 PortFa1_5Disable BOOL...
Page 463 Data Types Appendix A Table 147 - Input Data Type (16-port switches) (continued) AB:STRATIX_5700_16PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style AnyPortUnauthorizedDevice BOOL Decimal UnauthorizedDevice:0 PortFa1_1UnauthorizedDevice BOOL Decimal UnauthorizedDevice:1 PortFa1_2UnauthorizedDevice BOOL Decimal UnauthorizedDevice:2 PortFa1_3UnauthorizedDevice BOOL Decimal UnauthorizedDevice:3 PortFa1_4UnauthorizedDevice BOOL Decimal UnauthorizedDevice:4 PortFa1_5UnauthorizedDevice...
Page 464 Appendix A Data Types Table 147 - Input Data Type (16-port switches) (continued) AB:STRATIX_5700_16PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortFa1_4Utilization SINT Decimal PortFa1_5Utilization SINT Decimal PortFa1_6Utilization SINT Decimal PortFa1_7Utilization SINT Decimal PortFa1_8Utilization SINT Decimal PortFa1_9Utilization SINT Decimal PortFa1_10Utilization SINT Decimal...
Page 465: 20-Port Gb Switches
Data Types Appendix A 20-port Gb Switches Catalog numbers 1783-BMS20CGL, 1783-BMS20CGN, 1783-BMS20CGP, 1783-BMS20CGPK Table 149 - Input Data Type (20-port Gb switches) AB:STRATIX_5700_20PORT_GB_MANAGED:I:0 Member Name Type Default Valid Values Display Style Fault DINT Binary AnyPortConnected BOOL Decimal LinkStatus:0 PortFa1_1Connected BOOL Decimal LinkStatus:1 PortFa1_2Connected...
Page 466 Appendix A Data Types Table 149 - Input Data Type (20-port Gb switches) (continued) AB:STRATIX_5700_20PORT_GB_MANAGED:I:0 Member Name Type Default Valid Values Display Style PortFa1_12UnauthorizedDevice BOOL Decimal UnauthorizedDevice:12 PortFa1_13UnauthorizedDevice BOOL Decimal UnauthorizedDevice:13 PortFa1_14UnauthorizedDevice BOOL Decimal UnauthorizedDevice:14 PortFa1_15UnauthorizedDevice BOOL Decimal UnauthorizedDevice:15 PortFa1_16UnauthorizedDevice BOOL Decimal UnauthorizedDevice:16...
Page 467: 18-Port Gb Switches
Data Types Appendix A Table 149 - Input Data Type (20-port Gb switches) (continued) AB:STRATIX_5700_20PORT_GB_MANAGED:I:0 Member Name Type Default Valid Values Display Style PortFa1_8Utilization SINT Decimal PortFa1_9Utilization SINT Decimal PortFa1_10Utilization SINT Decimal PortFa1_11Utilization SINT Decimal PortFa1_12Utilization SINT Decimal PortFa1_13Utilization SINT Decimal PortFa1_14Utilization SINT...
Page 468 Appendix A Data Types Table 150 - Input Data Type (18-port Gb switches) (continued) AB:STRATIX_5700_18PORT_GB_MANAGED:I:0 Member Name Type Default Valid Values Display Style PortFa1_13Connected BOOL Decimal LinkStatus:13 PortFa1_14Connected BOOL Decimal LinkStatus:14 PortFa1_15Connected BOOL Decimal LinkStatus:15 PortFa1_16Connected BOOL Decimal LinkStatus:16 PortGi1_1Connected BOOL Decimal LinkStatus:19...
Page 469 Data Types Appendix A Table 150 - Input Data Type (18-port Gb switches) (continued) AB:STRATIX_5700_18PORT_GB_MANAGED:I:0 Member Name Type Default Valid Values Display Style PortFa1_13Threshold BOOL Decimal ThresholdExceeded:13 PortFa1_14Threshold BOOL Decimal ThresholdExceeded:14 PortFa1_15Threshold BOOL Decimal ThresholdExceeded:15 PortFa1_16Threshold BOOL Decimal ThresholdExceeded:16 PortGi1_1Threshold BOOL Decimal ThresholdExceeded:19...
Page 470 Appendix A Data Types Table 151 - Output Data Type (18-port Gb switches) (continued) AB:STRATIX_5700_20PORT_GB_MANAGED:O:0 Member Name Type Default Display Valid Values Style PortFa1_6Disable BOOL Decimal DisablePort:6 PortFa1_7Disable BOOL Decimal DisablePort:7 PortFa1_8Disable BOOL Decimal DisablePort:8 PortFa1_9Disable BOOL Decimal DisablePort:9 PortFa1_10Disable BOOL Decimal DisablePort:10...
Page 471: 20-Port Gb Switches
Data Types Appendix A 20-port Gb Switches Catalog numbers 1783-BMS20CGL, 1783-BMS20CGN, 1783-BMS20CGP, 1783-BMS20CGPK Table 152 - Input Data Type (20-port Gb switches) AB:STRATIX_5700_20PORT_GB_MANAGED:I:0 Member Name Type Default Valid Values Display Style Fault DINT Binary AnyPortConnected BOOL Decimal LinkStatus:0 PortFa1_1Connected BOOL Decimal LinkStatus:1 PortFa1_2Connected...
Page 472 Appendix A Data Types Table 152 - Input Data Type (20-port Gb switches) (continued) AB:STRATIX_5700_20PORT_GB_MANAGED:I:0 Member Name Type Default Valid Values Display Style PortFa1_12UnauthorizedDevice BOOL Decimal UnauthorizedDevice:12 PortFa1_13UnauthorizedDevice BOOL Decimal UnauthorizedDevice:13 PortFa1_14UnauthorizedDevice BOOL Decimal UnauthorizedDevice:14 PortFa1_15UnauthorizedDevice BOOL Decimal UnauthorizedDevice:15 PortFa1_16UnauthorizedDevice BOOL Decimal UnauthorizedDevice:16...
Page 473 Data Types Appendix A Table 152 - Input Data Type (20-port Gb switches) (continued) AB:STRATIX_5700_20PORT_GB_MANAGED:I:0 Member Name Type Default Valid Values Display Style PortFa1_8Utilization SINT Decimal PortFa1_9Utilization SINT Decimal PortFa1_10Utilization SINT Decimal PortFa1_11Utilization SINT Decimal PortFa1_12Utilization SINT Decimal PortFa1_13Utilization SINT Decimal PortFa1_14Utilization SINT...
Page 474: 20-Port Switches
Appendix A Data Types Table 153 - Output Data Type (20-port Gb switches) (continued) AB:STRATIX_5700_20PORT_GB_MANAGED:O:0 Member Name Type Default Valid Values Display Style PortFa1_18Disable BOOL Decimal DisablePort:18 PortGi1_1Disable BOOL Decimal DisablePort:19 PortGi1_2Disable BOOL Decimal DisablePort:20 20-port Switches Catalog numbers 1783-BMS20CL, 1783-BMS20CA Table 154 - Input Data Type (20-port switches) AB:STRATIX_5700_20PORT_MANAGED:I:0 Member Name...
Page 475 Data Types Appendix A Table 154 - Input Data Type (20-port switches) (continued) AB:STRATIX_5700_20PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortFa1_4UnauthorizedDevice BOOL Decimal UnauthorizedDevice:4 PortFa1_5UnauthorizedDevice BOOL Decimal UnauthorizedDevice:5 PortFa1_6UnauthorizedDevice BOOL Decimal UnauthorizedDevice:6 PortFa1_7UnauthorizedDevice BOOL Decimal UnauthorizedDevice:7 PortFa1_8UnauthorizedDevice BOOL Decimal UnauthorizedDevice:8 PortFa1_9UnauthorizedDevice...
Page 476 Appendix A Data Types Table 154 - Input Data Type (20-port switches) (continued) AB:STRATIX_5700_20PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style AllPortsUtilization SINT Decimal PortFa1_1Utilization SINT Decimal PortFa1_2Utilization SINT Decimal PortFa1_3Utilization SINT Decimal PortFa1_4Utilization SINT Decimal PortFa1_5Utilization SINT Decimal PortFa1_6Utilization SINT Decimal...
Page 477: 24-Port Switches
Data Types Appendix A Table 155 - Output Data Type (20-port switches) (continued) AB:STRATIX_5700_20PORT_MANAGED:O:0 Member Name Type Default Display Valid Values Style PortFa1_10Disable BOOL Decimal DisablePort:10 PortFa1_11Disable BOOL Decimal DisablePort:11 PortFa1_12Disable BOOL Decimal DisablePort:12 PortFa1_13Disable BOOL Decimal DisablePort:13 PortFa1_14Disable BOOL Decimal DisablePort:14 PortFa1_15Disable...
Page 478 Appendix A Data Types Table 156 - Input Data Type (24-port switches) (continued) AB:STRATIX_5700_24PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortFa1_17Connected BOOL Decimal LinkStatus:17 PortFa1_18Connected BOOL Decimal LinkStatus:18 PortFa1_19Connected BOOL Decimal LinkStatus:19 PortFa1_20Connected BOOL Decimal LinkStatus:20 PortFa1_21Connected BOOL Decimal LinkStatus:21 PortFa1_22Connected...
Page 479 Data Types Appendix A Table 156 - Input Data Type (24-port switches) (continued) AB:STRATIX_5700_24PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortFa1_5Threshold BOOL Decimal ThresholdExceeded:5 PortFa1_6Threshold BOOL Decimal ThresholdExceeded:6 PortFa1_7Threshold BOOL Decimal ThresholdExceeded:7 PortFa1_8Threshold BOOL Decimal ThresholdExceeded:8 PortFa1_9Threshold BOOL Decimal ThresholdExceeded:9 PortFa1_10Threshold...
Page 480 Appendix A Data Types Table 156 - Input Data Type (24-port switches) (continued) AB:STRATIX_5700_24PORT_MANAGED:I:0 Member Name Type Default Display Valid Values Style PortFa1_18Utilization SINT Decimal PortFa1_19Utilization SINT Decimal PortFa1_20Utilization SINT Decimal PortFa1_21Utilization SINT Decimal PortFa1_22Utilization SINT Decimal PortFa1_23Utilization SINT Decimal PortFa1_24Utilization SINT Decimal...
Page 481: Stratix 8000 And 8300 Data Types
Data Types Appendix A Table 157 - Output Data Type (24-port switches) (continued) AB:STRATIX_5700_24PORT_MANAGED:O:0 Member Name Type Default Display Valid Values Style PortFa1_22Disable BOOL Decimal DisablePort:22 PortFa1_23Disable BOOL Decimal DisablePort:23 PortFa1_24Disable BOOL Decimal DisablePort:24 The following tables show input and output data types for all 26 ports of the Stratix 8000 and 8300 switch, as well as port assignments for data types.
Page 482 Appendix A Data Types Table 158 - Input Data Types (continued) Tag Name Type Description AnyPortUnauthorizedDevice BOOL Indicates that an unauthorized MAC ID has attempted to communicate on any port. PortGi1_1UnauthorizedDevice BOOL Indicates that an unauthorized MAC ID has attempted to communicate on a particular port.
Page 483 Data Types Appendix A Table 158 - Input Data Types (continued) Tag Name Type Description PortGi1_1Threshold BOOL Indicates that unicast, multicast, or broadcast threshold limit has been exceeded on a particular port. PortGi1_2Threshold BOOL 0 = OK 1 = Threshold exceeded PortFa1_1Threshold BOOL PortFa1_2Threshold...
Page 484 Appendix A Data Types Table 158 - Input Data Types (continued) Tag Name Type Description PortGi1_1Utilization; SINT The percentage of the bandwidth utilized on a particular port. PortGi1_2Utilization; SINT PortFa1_1Utilization; SINT PortFa1_2Utilization; SINT PortFa1_3Utilization; SINT PortFa1_4Utilization; SINT PortFa1_5Utilization; SINT PortFa1_6Utilization; SINT PortFa1_7Utilization;...
Page 485 Data Types Appendix A Table 159 - Output Data Types Tag Name Type Description AllPortsDisable BOOL Setting this bit disables all ports on the switch. 0 = Enable 1 = Disable PortGi1_1Disable BOOL Setting a particular bit disables that particular port. 0 = Enable PortGi1_2Disable BOOL...
Page 486 Appendix A Data Types Notes: Rockwell Automation Publication 1783-UM007G-EN-P - February 2017...
Page 487: Port Assignments For Cip Data
Appendix Port Assignments for CIP Data Topic Page Stratix 5400 Port Assignments Stratix 5410 Port Assignments Stratix 5700 Port Assignments ArmorStratix 5700 Port Assignments Stratix 8000 and 8300 Port Assignments The following tables identify the instance numbers of the Ethernet link objects that are associated with each port on the switch.
Page 488: Stratix 5400 Port Assignments
Appendix B Port Assignments for CIP Data Stratix 5400 Port Assignments Table 160 - 8- and 12-port Switches 1783-HMS4C4CGN 1783-HMS8T4CGN 1783-HMS8S4CGN 1783-HMS4T4E4CGN 1783-HMS8TG4CGN 1783-HMS8SG4CGN 1783-HMS4EG8CGN 1783-HMS8TG4CGR 1783-HMS8SG4CGR 1783-HMS4EG8CGR 0 Any/All ports Any/All ports Any/All ports Any/All ports Any/All ports Any/All ports...
Page 489 Port Assignments for CIP Data Appendix B Table 161 - 16- and 20-port Switches 1783-HMS4S8E4CGN 1783-HMS4SG8EG4CGN 1783-HMS16T4CGN 1783-HMS16TG4CGN 1783-HMS8TG8EG4CGN 1783-HMS4SG8EG4CGR 1783-HMS16TG4CGR 1783-HMS8TG8EG4CGR 0 Any/All ports Any/All ports Any/All ports Any/All ports Any/All ports 1 Gi1/1 Gi1/1 Gi1/1 Gi1/1 Gi1/1 2 Gi1/2 Gi1/2 Gi1/2 Gi1/2...
Page 490: Stratix 5410 Port Assignments
Appendix B Port Assignments for CIP Data Stratix 5410 1783-IMS28NDC, 1783-IMS28NAC, 1783-IMS28GNDC, 1783-IMS28GNAC, 1783-IMS28RDC, 1783-IMS28RAC, 1783-IMS28GRDC, 1783-IMS28GRAC Port Assignments 0 Any/All ports 1 Gi1/1 2 Gi1/2 3 Gi1/3 4 Gi1/4 5 Gi1/5 6 Gi1/6 7 Gi1/7 8 Gi1/8 9 Gi1/9 10 Gi1/10 11 Gi1/11 12 Gi1/12...
Page 491: Stratix 5700 Port Assignments
Port Assignments for CIP Data Appendix B Stratix 5700 Port Assignments Table 162 - 6- and 10-port Switches 1783-BMS4S2SGL, 1783-BMS4S2SGA, 1783-BMS06TGL, 1783-BMS10CL, 1783-BMS10CGL, 1783-BMS10CGA, 1783-BMS06SL, 1783-BMS06SA, 1783-BMS10CGP, 1783-BMS10CGN 1783-BMS06TGA 1783-BMS10CA 1783-BMS06TL, 1783-BMS06TA, 1783-BMS06SGL, 1783-BMS06SGA 0 Any/All ports Any/All ports Any/All ports Any/All ports 1 Fa1/1 Fa/1...
Page 492: Armorstratix 5700 Port Assignments
Appendix B Port Assignments for CIP Data Table 163 - 18- and 20-port Switches (continued) 1783-BMS12T4E2CGL, 1783-BMS12T4E2CGP, 1783-BMS20CL, 1783-BMS20CA 1783-BMS20CGL, 1783-BMS20CGN, 1783-BMS12T4E2CGNK 1783-BMS20CGP, 1783-BMS20CGPK Fa1/19 Gi1/1 Fa1/20 Gi1/2 27 SVI1 SVI1 SVI1 ArmorStratix 5700 Port Assignments 1783-ZMS8TA 1783-ZMS4T4E2TGP, 1783-ZMS16TA 1783-ZMS8T8E2TGP, 1783-ZMS24TA 1783-ZMS4T4E2TGN 1783-ZMS8T8E2TGN...
Page 493: Stratix 8000 And 8300 Port Assignments
Port Assignments for CIP Data Appendix B Stratix 8000 and 8300 Port Assignments 6-port Managed 10-port Managed 10-port Managed 14-port Managed 14-port Managed 14-port Managed 18-port Managed Ethernet Switch Ethernet Switch Ethernet Switch Ethernet Switch Ethernet Switch Ethernet Switch Ethernet Switch 0 Any/All ports Any/All ports Any/All ports...
Page 494 Appendix B Port Assignments for CIP Data Notes: Rockwell Automation Publication 1783-UM007G-EN-P - February 2017...
Page 495: Port Numbering
Appendix Port Numbering Topic Page Stratix 5400 Port Numbering Stratix 5410 Port Numbering Stratix 5700 Port Numbering ArmorStratix 5700 Port Numbering Stratix 8000 and 8300 Port Numbering Rockwell Automation Publication 1783-UM007G-EN-P - February 2017...
Page 496: Stratix 5400 Port Numbering
• Unit number (always 1) • Port number (1…20, depending on the catalog number) Gigabit Ethernet is abbreviated as Gi and Fast Ethernet as Fa. Table 164 - Stratix 5400 Port Numbering Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.txt Text File...
Page 497 Port Numbering Appendix C Table 164 - Stratix 5400 Port Numbering (continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.txt Text File 1783-HMS4T4E4CGN 12-port (4 combo Gigabit ports; 4 Ethernet ports; Gi1/1 4 PoE/PoE+ ports) managed switch; Layer 2 firmware...
Page 498 Appendix C Port Numbering Table 164 - Stratix 5400 Port Numbering (continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.txt Text File 1783-HMS4S8E4CGN 16-port (4 combo Gigabit ports; 8 PoE/PoE+ ports; Gi1/1 4 SFP ports) managed switch; Layer 2 firmware...
Page 499 Port Numbering Appendix C Table 164 - Stratix 5400 Port Numbering (continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.txt Text File 1783-HMS16T4CGN 20-port (4 combo Gigabit ports; 16 Ethernet ports) Gi1/1 managed switch; Layer 2 firmware...
Page 500 Appendix C Port Numbering Table 164 - Stratix 5400 Port Numbering (continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.txt Text File 1783-HMS8TG8EG4CGN 20-port (8 Gigabit ports; 4 Gigabit combo ports; 8 Gigabit Gi1/1 PoE/PoE+ ports) managed switch; Layer 2 firmware...
Page 501 Port Numbering Appendix C Table 164 - Stratix 5400 Port Numbering (continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.txt Text File 1783-HMS4EG8CGR 12-port (4 Gigabit ports; 4 Gigabit combo ports; 4 Gigabit Gi1/1 PoE/PoE+ ports) managed switch; Layer 3 firmware...
Page 502 Appendix C Port Numbering Table 164 - Stratix 5400 Port Numbering (continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.txt Text File 1783-HMS4SG8EG4CGR 16-port (4 Gigabit combo ports; 8 Gigabit PoE/PoE+ ports; Gi1/1 4 Gigabit SFP ports) managed switch; Layer 3 firmware...
Page 503 Port Numbering Appendix C Table 164 - Stratix 5400 Port Numbering (continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.txt Text File 1783-HMS8TG8EG4CGR 20-port (8 Gigabit ports; 4 Gigabit combo ports; 8 Gigabit Gi1/1 PoE/PoE+ ports) managed switch; Layer 3 firmware...
Page 504: Stratix 5410 Port Numbering
Appendix C Port Numbering Stratix 5410 Port Numbering The port ID consists of the following: • Port type (Gigabit Ethernet or 10 Gigabit Ethernet) • Unit number (always 1)) • Port number (1…28) Gigabit Ethernet is abbreviated as Gi and 10 Gigabit Ethernet as Te. Table 165 - Stratix 5410 Port Numbering Cat.
Page 505: Stratix 5700 Port Numbering
Port Numbering Appendix C Stratix 5700 Port Numbering The port ID consists of the following: • Port type (Gigabit Ethernet for Gigabit ports and Fast Ethernet for 10/100 Mbps ports) • Unit number (always 1) • Port number (1…2 for Gigabit ports, 1…18 for all others, depending on the catalog number) Gigabit Ethernet is abbreviated as Gi and Fast Ethernet as Fa.
Page 506 Appendix C Port Numbering Table 166 - Stratix 5700 Port Numbering (continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.text File 1783-BM06SGA 6-port (4 Ethernet ports; 2 SFP Gigabit slots) managed switch; Fa1/1 full firmware Fa1/2 Fa1/3 Fa1/4 Gi1/1...
Page 507 Port Numbering Appendix C Table 166 - Stratix 5700 Port Numbering (continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.text File 1783-BMS10CGA 10-port (8 Ethernet ports; 2 combo Gigabit ports) managed switch; Fa1/1 full firmware Fa1/2 Fa1/3 Fa1/4 Fa1/5...
Page 508 Appendix C Port Numbering Table 166 - Stratix 5700 Port Numbering (continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.text File 1783-BMS12T4E2CGP 18-port (12 Ethernet ports; 4 PoE/PoE+ ports; 2 combo Gigabit ports) Fa1/1 managed switch; full firmware; PTP Fa1/2 Fa1/3 Fa1/4...
Page 509 Port Numbering Appendix C Table 166 - Stratix 5700 Port Numbering (continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.text File 1783-BMS20CA 20-port (16 Ethernet ports; 2 SFP slots; 2 combo ports) managed Fa1/1 switch; full firmware Fa1/2 Fa1/3 Fa1/4...
Page 510 Appendix C Port Numbering Table 166 - Stratix 5700 Port Numbering (continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.text File 1783-BMS20CGN 20-port (16 Ethernet ports; 2 SFP slots; 2 combo Gigabit ports) Fa1/1 managed switch; full firmware; PTP; NAT Fa1/2 Fa1/3 Fa1/4...
Page 511 Port Numbering Appendix C Table 166 - Stratix 5700 Port Numbering (continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.text File 1783-BMS20CGPK 20-port (16 Ethernet ports; 2 SFP slots; 2 combo Gigabit ports) Fa1/1 managed switch; full firmware; PTP; conformal coating Fa1/2 Fa1/3 Fa1/4...
Page 512: Armorstratix 5700 Port Numbering
Appendix C Port Numbering ArmorStratix 5700 The port ID consists of the following: • Port type (Gigabit Ethernet for Gigabit ports and Fast Ethernet for Port Numbering 10/100 Mbps ports) • Unit number (always 1) • Port number (1…2 for Gigabit ports, 1…18 for all others, depending on the catalog number) Gigabit Ethernet is abbreviated as Gi and Fast Ethernet as Fa.
Page 513 Port Numbering Appendix C Table 167 - ArmorStratix 5700 Port Numbering (continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.text File 1783-ZMS8T8E2TGP 18-port (2 Gigabit ports; 8 Ethernet ports; 8 PoE/PoE+ ports) GE-1 Gi1/1 managed switch; full firmware; PTP GE-2 Gi1/2 Fa1/1...
Page 514 Appendix C Port Numbering Table 167 - ArmorStratix 5700 Port Numbering (continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.text File 1783-ZMS24TA 24-port (24 Ethernet ports) managed switch; full firmware Fa1/1 Fa1/2 Fa1/3 Fa1/4 Fa1/5 Fa1/6 Fa1/7 Fa1/8 Fa1/9...
Page 515: Stratix 8000 And 8300 Port Numbering
Port Numbering Appendix C Stratix 8000 and 8300 The port ID consists of the following: • Port type (Gigabit Ethernet for Gigabit ports and Fast Ethernet for Port Numbering 10/100 Mbps ports) • Unit number (1, 2, or 3) • Port number (1…2 for Gigabits, 1…4 for the 6-port base and 1…8 for all others) Gigabit Ethernet is abbreviated as Gi and Fast Ethernet as Fa.
Page 516 Appendix C Port Numbering Table 168 - Stratix 8000/8300 Switch and Expansion Module Port Numbering (continued) Cat. No. Description Port Numbering on Switch Labels Port Numbering in config.txt Text File 1783-MX04E 4-port (4 PoE ports) expansion module Fa#/1 Fa#/2 Fa#/3 Fa#/4 1783-MX04T04E 8-port(4 Ethernet ports;...
Page 517: Cables And Connectors
Cables and Connectors Topic Page Stratix 5410 Cables and Connectors Stratix 5400 and 5700 Cables and Connectors ArmorStratix 5700 Cables and Connectors Stratix 8000/8300 Cables and Connectors For recommended cables and SFP modules, see the Stratix Ethernet Device Specifications Technical Data, publication 1783-TD001.
Page 518: Connect To 10Base-T- And 100Base-Tx-Compatible Devices
Appendix D Cables and Connectors Connect to 10BASE-T- and 100BASE-TX-Compatible Devices The auto-MDIX feature is enabled by default. Follow these cabling guidelines when the auto-MDIX feature has been disabled. When connecting the ports to 10BASE-T- and 100BASE-TX-compatible devices, such as servers and routers, you can use a two or four twisted-pair, straight-through cable that is wired for 10BASE-T and 100BASE-TX.
Page 519 Cables and Connectors Appendix D You can use Category 3, 4, or 5 cabling when connecting to 10BASE-T- compatible devices. You must use Category 5 cabling when connecting to 100BASE-TX-compatible devices. IMPORTANT Use a four twisted-pair, Category 5 cable when connecting to a 1000BASE-T- compatible device or PoE port.
Page 520: Console Ports
Appendix D Cables and Connectors Console Ports Console ports enable you to connect a switch to a computer if you use the Command-line interface (CLI) to configure and monitor a switch. Stratix 5410 switches have these console ports: • A USB 5-pin mini-Type B port on the front panel •...
Page 521 Cables and Connectors Appendix D The following table lists the pinouts for the console port, the RJ45-to-DB-9 adapter cable, and the console device. Table 169 - Pinouts with DB-9 Pin Switch Console Port (DTE) RJ45-to-DB-9 Terminal Adapter Console Device Signal DB-9 Pin Signal The following table lists the pinouts for the console port, RJ45-to-DB-25...
Page 522: Alarm Port
Appendix D Cables and Connectors Alarm Port The front panel alarm port uses an RJ45 connector. Figure 65 - Front Panel Alarm Connector Figure 66 - Alarm Connector Pinout Label 4 5 6 7 8 Alarm 1 input Alarm 2 input Alarm output normally closed Alarm 3 input Alarm 4 input...
Page 523: Stratix 5400 And 5700 Cables And Connectors
Cables and Connectors Appendix D Stratix 5400 and 5700 This section describes how to connect to ports on Stratix 5400 and Stratix 5700 switches. Cables and Connectors 10/100 and 10/100/1000 Ports The 10/100 and 10/100/1000 Ethernet ports use standard RJ45 connectors and Ethernet pinouts with internal crossovers.
Page 524: Connect To 10Base-T- And 100Base-Tx-Compatible Devices
Appendix D Cables and Connectors Connect to 10BASE-T- and 100BASE-TX-Compatible Devices The auto-MDIX feature is enabled by default. Follow these cabling guidelines when the auto-MDIX feature has been disabled. When connecting the ports to 10BASE-T- and 100BASE-TX-compatible devices, such as servers and routers, you can use a two or four twisted-pair, straight-through cable that is wired for 10BASE-T and 100BASE-TX.
Page 525: Dual-Purpose Ports (Combo Ports)
Cables and Connectors Appendix D You can use Category 3, 4, or 5 cabling when connecting to 10BASE-T- compatible devices. You must use Category 5 cabling when connecting to 100BASE-TX-compatible devices. IMPORTANT Use a four twisted-pair, Category 5 cable when connecting to a 1000BASE-T- compatible device or PoE port.
Page 526: Console Ports
Appendix D Cables and Connectors Console Ports Console ports enable you to connect a switch to a computer if you use the Command-line interface (CLI) to configure and monitor a switch. Stratix 5700 switches have these console ports: • A USB 5-pin mini-Type B port on the front panel The USB console port uses a USB Type A to 5-pin mini-Type B cable.
Page 527 Cables and Connectors Appendix D The following table lists the pinouts for the console port, the RJ45-to-DB-9 adapter cable, and the console device. Table 171 - Pinouts with DB-9 Pin Switch Console Port (DTE) RJ45-to-DB-9 Terminal Adapter Console Device Signal DB-9 Pin Signal The following table lists the pinouts for the console port, RJ45-to-DB-25...
Page 528: Alarm Ports
Appendix D Cables and Connectors Alarm Ports The front-panel alarm-relay connector ports are described in the following illustration and table. Figure 75 - Wiring Example for Alarm Inputs and Outputs Alarms Connector To Alarm Input Alarm +24V DC from User Relay Coil To Alarm Input...
Page 529: Armorstratix 5700 Cables And Connectors
Cables and Connectors Appendix D ArmorStratix 5700 This section describes how to connect to ports on ArmorStratix 5700 switches. For connecting DC power to the power connector, see page 155. Cables and Connectors 10/100 Ports The 10/100 Ethernet ports use M12 D-coded 4-pin connectors and Ethernet pinouts with twisted-pair crossovers or straight-through cables.
Page 530: Connect To 10Base-T- And 100Base-Tx-Compatible Devices
Appendix D Cables and Connectors Connect to 10BASE-T- and 100BASE-TX-Compatible Devices The auto-MDIX feature is enabled by default. Follow these cabling guidelines when the auto-MDIX feature has been disabled. When connecting the ports to 10BASE-T- and 100BASE-TX-compatible devices, such as servers and routers, you can use a two or four twisted-pair, straight-through cable that is wired for 10BASE-T and 100BASE-TX.
Page 531 Cables and Connectors Appendix D When connecting the ports to 10BASE-T- and 100BASE-TX-compatible devices, such as switches or repeaters, you can use a two or four twisted-pair, crossover cable. Use a straight-through cable to connect two ports when only one port is designated with an X.
Page 532: Console Port
Connect to the console port with an M12-to-DB-9 cable (Figure 82): • Obtain a male 5-pin DC Micro-style (M12) connector configuration cordset, such as Allen-Bradley Bulletin 889D. • Obtain a DB-9 connector and attach it to one end of the cable. Figure 82 - M12-to-DB-9 Cable 32552-M...
Page 533: Alarm Ports
Alarm ports are included only on ArmorStratix 5700 switches with PoE. Figure 85 shows the front-panel alarm relay connector and ports. The alarm connector uses a male 5-pin DC Micro-style (M12) connector configuration cordset, such as Allen-Bradley Bulletin 889D. Figure 85 - Alarm Connector Pinout Unconnected Unconnected...
Page 534: Poe Port Cable Specifications
Appendix D Cables and Connectors PoE Port Cable Specifications For PoE ports, use a Category 5 (Cat 5) cable with a distance of up to 100 m (328 ft). Stratix 8000/8300 This section describes how to connect to ports on Stratix 8000/8300 switches. Cables and Connectors 10/100 and 10/100/1000 Ports The 10/100 and 10/100/1000 Ethernet ports use standard RJ45 connectors...
Page 535: Connect To 10Base-T- And 100Base-Tx-Compatible Devices
Cables and Connectors Appendix D The PoE ports on the PoE expansion modules integrate power and data signals on the same wires. The ports use standard RJ45 connectors and Ethernet pinouts with internal crossovers. Figure 89 - 10/100 PoE Connector Pinouts and Power Sourcing Equipment (PSE) Voltage Label Alternative A (MDI) 4 5 6 7 8...
Page 536 Appendix D Cables and Connectors When connecting the ports to 10BASE-T- and 100BASE-TX-compatible devices, such as switches or repeaters, you can use a two or four twisted-pair, crossover cable. Use a straight-through cable to connect two ports only when one port is designated with an X.
Page 537: 100Base-Fx Ports
Cables and Connectors Appendix D 100Base-FX Ports The 100Base-FX ports use the following: • LC connectors, as shown in the following figure • 50/125- or 62.5 /125-micron multimode fiber-optic cables Figure 94 - Fiber-optic SFP Module LC Connector ATTENTION: Invisible laser radiation can be emitted from disconnected fibers or connectors.
Page 538: Console Port
Appendix D Cables and Connectors Console Port The console port enables you to connect the switch to a computer if you use the Command-line interface (CLI) to configure and monitor the switch. The console port uses an 8-pin RJ45 connector. The supplied RJ45-to-DB-9 adapter cable connects the console port of the switch to a computer.
Page 539: Poe Port Cable Specifications
Cables and Connectors Appendix D The following table lists the pinouts for the console port, RJ45-to-DB-25 female DTE adapter, and the console device. The RJ45-to-DB-25 female DTE adapter is not supplied with the switch. Table 174 - Pinouts with DB-25 Pin Switch Console Port (DTE) RJ45-to-DB-25 Terminal Adapter Console Device...
Page 540: Rockwell Automation Publication 1783-Um007G-En-P - February
Appendix D Cables and Connectors Notes: Rockwell Automation Publication 1783-UM007G-EN-P - February 2017...
Page 541 Index Numerics using 518 damaged 419 10/100 ports detect with auto-MDIX 77 cable lengths 75 Ethernet and fiber 419 connecting to 93 identify 535 10/100/1000 ports PoE module specifications 539 straight-through cable lengths 75 two twisted-pair pinout 518 connecting to 93 using 518 cabling auto-MDIX 94...
Page 542 Index default gateway Express Setup NAT 255 button 32 default router 240 global macro 44 Long Press mode 37 default VLAN 353 Medium Press mode 36 delay request interval 206 modes 34 denial-of-service attack 309 Multi-mode 34 Device Manager requirements 30 access 48 Short Press mode 35 hardware requirements 47...
Page 543 Index IOS software mode cryptographic 212 Access 350 non-cryptographic 212 Boundary 194 IP address DHCP Server 238 Direct Managed 423 customization DLR 226 connected devices 238 dual power 191 DHCP IP address pool 240 End to End Transparent 195 switch port 241 EtherChannel 245 DHCP IP address pool Express Setup 34...
Page 544 Index power classifications 315 power priority 321 parts list 76 prevent electrostatic discharge 74 pinouts 10/100 ports 537 proxy settings 48 crossover cables 536 four twisted-pair, 1000BASE-T ports configure Device Manager 298 PoE 523 overview 297 RJ45-to-DB-25 adapter 539 status 410 RJ45-to-DB-25 terminal adapter 521 RJ45-to-DB-9 configure via Device Manager 196...
Page 545 Index RSTP STCN STP 330 features 362 storm control RSWho 44 described 309 thresholds 309 straight-through cable pinout two twisted-pair 10/100 ports 518 SC connector 537 SD card install or remove 78 Stratix switch families 18 synchronize subnet mask configuration 65 DHCP IP address pool 240 synchronize IOS files 65 subnet translation 259...
Page 546 Index time synchronization configure via Device Manager 196 configure via Logix Designer application 204 timing message settings 196 traffic fixups and NAT 262 traffic permits and NAT 262 traffic suppression 309 translate IP addresses 254 translation entry types 259 Transmit Detail tab, dashboard 395 troubleshoot Device Manager display 421 Device Manager not accessible 421...
Page 548: Documentation Feedback
Rockwell Automation maintains current product environmental information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page. Allen-Bradley, ArmorStratix, Rockwell Automation, Rockwell Software, RSLinx, RSLogix 5000, RSNetWorx, Stratix, Studio 5000, and Studio 5000 Logix Designer are trademarks of RockwellAutomation, Inc. Trademarks not belonging to Rockwell Automation are property of their respective companies.

This manual is also suitable for:

Stratix 5410 Stratix 8300 1783-hms 1783-ims 1783-bms 1783-zms ... Show all

Allen-Bradley Stratix 5400 User Manual

Preface

Summary of Changes

About the Switches

Chapter 1 Ethernet/Ip CIP Interface

Get Started

Chapter 2 Express Setup Overview

Install Stratix 5400 Switches

Chapter 3

Specifications

Install Stratix 5410 Switches

Chapter 4

Switch Specifications

Chapter 5

Install Stratix 5700 Switches

Specifications

Install Stratix 8000 and 8300 Switches

Chapter 6

Configure Switch Features

Chapter 7 Access Control Lists (Acls)

Monitor the Switch

Chapter 8 Switch Status Via Device Manager

Troubleshoot the Switch

Chapter 9 Troubleshoot the Installation

Quick Links

Related Manuals for Allen-Bradley Stratix 5400

Summary of Contents for Allen-Bradley Stratix 5400