Philips PIP3202-DC Specification Sheet
  1. Manuals
  2. Brands
  3. Philips Manuals
  4. Switch
  5. PIP3202-DC
  6. Specification sheet
Philips PIP3202-DC Specification Sheet

Philips PIP3202-DC Specification Sheet

Topfet dual high side switch
Hide thumbs
Table of Contents

Quick Links

Philips Semiconductors
TOPFET dual high side switch
DESCRIPTION
Monolithic dual channel high side
protected power switch in
TOPFET2 technology assembled in
a 7 pin plastic surface mount
package.
APPLICATIONS
General purpose switch for driving
lamps, motors, solenoids, heaters.
FEATURES
Vertical power TrenchMOS
Low on-state resistance
CMOS logic compatible
Very low quiescent current
Overtemperature protection
Load current limiting
Latched overload and
short circuit protection
Overvoltage and undervoltage
shutdown with hysteresis
Off-state open circuit
load detection
Diagnostic status indication
Voltage clamping for turn off
of inductive loads
ESD protection on all pins
Reverse battery, overvoltage
and transient protection
PINNING - SOT427
PIN
DESCRIPTION
1
load 1
2
ground
3
input 1
4
connected to mb
5
status
6
input 2
7
load 2
mb
battery
CONVENTION
Positive currents flow into pins, except for load and ground pins.
September 2001
QUICK REFERENCE DATA
SYMBOL
PARAMETER
I
Nominal load current (ISO)
L
SYMBOL
PARAMETER
V
Continuous off-state supply voltage
BG
I
Continuous load current
L
T
Continuous junction temperature
j
R
On-state resistance, T
ON
FUNCTIONAL BLOCK DIAGRAM
INPUT 1
INPUT 2
STATUS
GROUND
Fig.1. Elements of the TOPFET dual HSS with internal ground resistor.
PIN CONFIGURATION
mb
1 2 3 4 5 6 7
Fig. 2.
1
= 25˚C
j
CONTROL &
PROTECTION
CIRCUITS
RG
SYMBOL
Product specification
PIP3202-DC
MIN.
UNIT
8
A
MAX.
UNIT
50
V
16
A
150
˚C
40
m
BATT
LOAD 1
LOAD 2
B
I1
L1
DUAL
HSTF
I2
L2
S
G
Fig. 3.
Rev 1.000
Table of Contents
loading

Related Manuals for Philips PIP3202-DC

Summary of Contents for Philips PIP3202-DC

  • Page 1 Philips Semiconductors TOPFET dual high side switch DESCRIPTION Monolithic dual channel high side protected power switch in TOPFET2 technology assembled in a 7 pin plastic surface mount package. APPLICATIONS General purpose switch for driving lamps, motors, solenoids, heaters. FEATURES Vertical power TrenchMOS...

  • Page 2: Limiting Values

    Philips Semiconductors TOPFET dual high side switch LIMITING VALUES Limiting values in accordance with the Absolute Maximum System (IEC 134) SYMBOL PARAMETER Continuous supply voltage Continuous load current per channel Total power dissipation Storage temperature Continuous junction temperature Reverse battery voltages...

  • Page 3: Static Characteristics

    On-state resistance 1 Of the output Power MOS transistors. 2 For a high side switch, the load pin voltage goes negative with respect to ground during the turn-off of an inductive load. This negative voltage is clamped by the device.

  • Page 4: Input Characteristics

    Philips Semiconductors TOPFET dual high side switch INPUT CHARACTERISTICS 5.5 V 35 V. Limits are at -40˚C SYMBOL PARAMETER Input current Input clamping voltage Input turn-on threshold voltage IG(ON) Input turn-off threshold voltage IG(OFF) Input turn-on hysteresis Input turn-on current...

  • Page 5: Overload Protection Characteristics

    1 Undervoltage sensors causes each channel to switch off and reset. 2 Overvoltage sensors causes each output channel to switch off to protect its load. 3 Above this temperature measurement of these parameters is prevented because OT protection may occur prior to SC protection.

  • Page 6: Truth Table

    Philips Semiconductors TOPFET dual high side switch STATUS CHARACTERISTICS The status output is an open drain transistor, and requires an external pull-up circuit to indicate a logic high. Limits are at -40˚C 150˚C and typicals at T SYMBOL PARAMETER Status clamping voltage...

  • Page 7: Switching Characteristics

    Philips Semiconductors TOPFET dual high side switch SWITCHING CHARACTERISTICS = 25 ˚C, V = 13 V, for resistive load R SYMBOL PARAMETER During turn-on Delay time d on dV/dt Rate of rise of load voltage Total switching time During turn-off...

  • Page 8: Mechanical Data

    Philips Semiconductors TOPFET dual high side switch MECHANICAL DATA Plastic single-ended surface mounted package (Philips version of D 7 leads (one lead cropped) DIMENSIONS (mm are the original dimensions) UNIT 1.40 4.50 0.85 1.27 4.10 0.60 OUTLINE VERSION SOT427 Fig.4. SOT427 surface mounting package 1 Epoxy meets UL94 V0 at 1/8".

  • Page 9: Life Support Applications

    Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale.

Table of Contents