1. Manuals
  2. Brands
  3. Toa Manuals
  4. Recording Equipment
  5. N-8010RS
  6. Installation manual

Toa N-8010RS Installation Manual

Substation interface unit
Hide thumbs
Table of Contents

Quick Links

INSTALLATION MANUAL
SUbSTATION INTerfAce UNIT
N-8010rS
Thank you for purchasing TOA's Substation Interface Unit.
Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.
Table of Contents
loading

Related Manuals for Toa N-8010RS

Summary of Contents for Toa N-8010RS

  • Page 1 INSTALLATION MANUAL SUbSTATION INTerfAce UNIT N-8010rS Thank you for purchasing TOA’s Substation Interface Unit. Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.

  • Page 2: Table Of Contents

    TAbLe Of cONTeNTS 1. SAfeTY PrecAUTIONS ................3 2. GeNerAL DeScrIPTION ................5 3. feATUreS ......................5 4. NOMeNcLATUre AND fUNcTIONS ..........6 Front ..........................6 Rear ..........................6 5. INSTALLATION ....................7 5.1. Equipment Rack Mounting ..................7 5.1.1. Setting space ....................8 5.1.2.

  • Page 3: Safety Precautions

    · The supplied rack-mounting screws can be used from the AC outlet and contact your nearest TOA for the TOA equipment rack only. Do not use them dealer. Make no further attempt to operate the unit for other racks.
  • Page 4 • En cas de survenue des irrégularités suivantes pendant l’utilisation, débrancher immédiatement la • Ne pas obstruer les fentes de ventilation sur le capot fiche du cordon d’alimentation de la prise secteur de l’unité sous peine de provoquer une accumulation et contacter le représentant TOA le plus proche. de chaleur à l’intérieur de l’appareil, pouvant aboutir Ne pas essayer pas d’utiliser l’appareil dans ces à un incendie. Nettoyer régulièrement les encoches conditions sous peine de provoquer un incendie ou de ventilation.

  • Page 5: General Description

    DeScrIPTION GÉNÉrALe L'unité N-8010RS de TOA est l'interface de sous-station utilisée pour le système de paquet intercom des séries N-8000 (intercom compatible avec un réseau IP) utilisant une technologie de paquet audio*. Elle permet de brancher jusqu'à 16 sous-stations à l'aide de câbles blindés à deux brins. Il est possible de...

  • Page 6: Nomenclature And Functions

    4. NOMeNcLATUre AND fUNcTIONS [front] 1 2 3 4 5 1. reset key [reSeT] 4. Power indicator [POWer] (Green) Pressing this key reactivates the unit. Lights when power is supplied to the unit. 2. LNK/AcT indicator [LNK/AcT] (Green) 5. MAc address Lights when connected to a network, and flashes This is the MAC address* for the unit.

  • Page 7: Installation

    The N-8010RS can be installed in any of three ways: Equipment rack mounting, Desk-top installation, and Wall mounting. INSTALLATION L’unité N-8010RS peut être installée de trois manières : Montage en bâti, Montage sur bureau, et Montage mural. 5.1. equipment rack Mounting A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient.

  • Page 8: Setting Space

    5.1.1. Setting space For maintenance works, allow much space between the wall and Equipment rack. espace à prévoir Prévoyez un espace suffisant entre le mur et le bâti en N-8010RS 50 cm prévision des travaux de maintenance. 50 cm 50 cm 5.1.2. caution when installing the unit Avertissement lors de l’installation de l’appareil...

  • Page 9: Mounting On The Rack

    (accessoire) (accessoire) Rack mounting screw 5 x 12 with plain washer (accessory) Vis de montage en bâti 5 x 12 avec rondelle simple (accessoire) Step 1. Install the rack-mounting bracket to the N-8010RS. Step 2. Mount the N-8010RS on the Equipment rack. Étape 1. Installez la patte de montage en bâti sur l’unité N-8010RS. Étape 2. Montez l’unité N-8010RS en bâti. 5.2. Desk-Top Installation When installing the N-8010RS on a desk, secure the supplied plastic feet to the bottom surface of the N-8010RS using the supplied machine screws.

  • Page 10: Wall Mounting

    5.3. Wall Mounting Step 1. Install the optional YC-850 Wall-mounting bracket to the N-8010RS. Step 2. Mount the N-8010RS on the wall. Notes • Use appropriate screws for the construction of N-8010RS wall. • Wood screws 3.5 x 20 are supplied with the YC-850. • The socket-outlet shall be installed near the equipment and the plug (disconnecting device) shall be easily accessible.

  • Page 11: Wiring

    6. WIrING 6.1. connection Diagram N-8010RS Substation interface unit 16 lines Be sure to ground. RJ-45 connector 3P removable terminal plug (accessory) To AC mains or a UPS To network (Uninterruptible power supply system)* To Line A (orange) Note 2-core shielded cable...
  • Page 12 Schéma de branchements Unité d'interface de sous-station N-8010RS 16 lignes Ne pas oublier la mise à la terre. Connecteur RJ45 Prise 3P amovible (accessoire) Vers prise secteur CA Vers le réseau (ou système d'alimentation sans interruption)* Remarque Vers ligne A (orange) Câble blindé...

  • Page 13: Type Of Cable

    Indoor wires may also be used, however, in case where there is no risk of deterioration due to exposure to heat, etc. • Make sure that the 2-core shielded cable is used for wiring from the substation interface unit to the substation (RS-150, RS-160, RS-170, and RS-180). Note Specifications related to connections are as follows. Removable terminal plug (N-8010RS line terminal) Conductor diameter: ø 0.5 – 2 mm (AWG12 – 24), Solid wire/Stranded wire Clip terminal (E-7000TB) Conductor diameter: ø 0.4 – 0.8 mm (AWG20 – 26), Solid wire Outside diameter: ø 0.5 mm or below 6.3.

  • Page 14: E-7000Tb Terminal Board Wiring

    Step 4. Insert the wired terminal plug into the terminal block of the N-8010RS. N-8010RS rear panel Tighten Removable terminal plug (accessory) Removable terminal block 6.5. e-7000Tb Terminal board Wiring For cable connection to the E-7000TB Terminal Board, use the optional YC-105 Clipping tool. Hook the end of the cable onto the terminal and, with the cable end in hand, press the YC-105 down onto the terminal from above. Pressing down the YC-105 tool cuts off the excess cable end, securing the connection.

  • Page 15: Accessories

    7. AcceSSOrIeS AC power cord (2 m) ..........1 Machine screw M3 x 8 ..........4 CD* (for PC setting, maintenance use) ....1 Rack mounting bracket ........... 2 Removable terminal plug (3 pins) ......16 Tapping screw 3 x 8 ..........8 Plastic foot ..............
  • Page 16 Example: Prepared in September 2009: 200909 Informations sur les versions de mise à jour • Les fiches techniques des produits TOA sont disponibles au téléchargement sur le site web à l’adresse http://www.toa-products.com/international/ où vous trouverez également les versions les plus récentes du logiciel, du microprogramme et des notices de référence de l’unité N-8000.

Table of Contents