Hitachi CR 18DMR Handling Instructions Manual
Hide thumbs
Also See for CR 18DMR:
- Safety and instruction manual (96 pages) ,
- Handling instructions manual (55 pages) ,
- Technical data and service manual (29 pages)
Related Manuals for Hitachi CR 18DMR
Summary of Contents for Hitachi CR 18DMR
- Page 1 Cordless Reciprocating Saw CR 18DMR CR 18DL • HANDLING INSTRUCTIONS CR18DL Read through carefully and understand these instructions before use.
- Page 4 3 mm 11.5 mm...
- Page 5 18V Ni-Cd or Ni-MH Rechargeable battery 18V Li-ion Rechargeable battery Latch Pull out Insert Housing Push Insert Pilot lamp Hole for connecting the rechargeable battery Lever Front cover Blade Plunger slit Another blade Blade holder Machine oil Rubber Cap Blade hole Hexagonal bar wrench Base Set screw 12 mm...
- Page 7 ° ° ° °...
- Page 11 –...
- Page 15 °...
- Page 16 d) Remove any adjusting key or wrench before GENERAL SAFETY RULES turning the power tool on. A wrench or a key left attached to a rotating part WARNING! of the power tool may result in personal injury. Read all instructions e) Do not overreach.
-
Page 17: Caution On Lithium-Ion Battery
13. Do not touch the blade during or immediately c) Use power tools only with specifically designated after operation. The blade becomes very hot during battery packs. operation and could cause serious burns. Use of any other battery packs may create a risk 14. -
Page 18: Specifications
CAUTION 1. If liquid leaking from the battery gets into your eyes, do not rub your eyes and wash them well with fresh clean water such as tap water and contact a doctor immediately. If left untreated, the liquid may cause eye-problems. 2. -
Page 19: Standard Accessories
STANDARD ACCESSORIES CR18DMR CR18DL 1 Blade (No. 103) ....................... 1 2 Hexagonal bar wrench ....................1 3 Charger (UC24YFA or UC18YG or UC18YRL) ............1 4 Battery CR18DMR (2BLFK) (2HLFK), CR18DL (2MRK) ..........2 CR18DMR (BLFK) (HLFK), CR18DL (MRK) ............ 1 5 Plastic case ........................ - Page 20 CAUTION When the battery becomes fully recharged, the pilot If the battery is inserted in the reverse direction, lamp will blink in red (At 1-second intervals) (See not only recharging will become impossible, but it Table 1). may also cause problems in the charger such as (1) Pilot lamp indication deformed recharging terminal.
-
Page 21: Prior To Operation
120 minutes have elapsed after starting of the moves slightly (Fig. 11). charging, stop the charging and contact your CAUTION HITACHI AUTHORIZED SERVICE CENTER. When pulling the saw blade, be absolutely sure to CAUTION pull it from the back. Pulling other parts of the blade If the battery is heated due to direct sunlight, will result in an injury. -
Page 22: How To Use
CAUTION The motor can be locked sometimes, depending on Do not use any saw blade with a worn-out blade the combination of the material to be cut and the hole. Otherwise, the saw blade can come off, blade. Whenever the motor gets locked, switch it resulting in personal injury (Fig. -
Page 23: Selection Of Blades
Table 4: Bl-METAL blades SELECTION OF BLADES Blade Thickness To ensure maximum operating efficiency and results, Uses (mm) it is very important to select the appropriate blade best No. 101 For cutting steel and stainless pipes suited to the type and thickness of the material to be 2.5 –... -
Page 24: Maintenance And Inspection
NOTE When replacing the carbon brush with a new one, Due to HITACHI’s continuing program of research and be sure to use the Hitachi Carbon Brush Code No. development, the specifications herein are subject to 999058. change without prior notice. - Page 28 Code No. C99140122 G Printed in China...