Quick Links
Cordless Driver Drill
Capacities
Steel
Wood
Wood screw
Machine screw
Equipped with Electric Brake
MODEL 6201D
MODEL 6201DW
With Fast Charger
Dimensions
Net
No
load speed IRPM)
High
Low
1L
x W x H)
weight
INSTRUCTION MANUAL
*
Battery Cartridge 9100
Voltage
Charging time
9.6
V
1
Hr.
SPECIFICATIONS
Model DC9700 Fast Charger
Input
output
A.C. only 50 Hz
-
60 Hz
D.C.
7.2
V,
9 6
V
Model 6201D
10
mm
21
mm
6.1
mm x
55
mm
-
-
350
237
mm x
57 m m
x
243
mm
1.7
kg
(318'7
1
113116")
I
l 1 / 4 "
x
2-3/16")
I
6 m m
'"4''
1
1
I
19-318"
x
2-114"
x
9-9/16")
I
13.7
lbsl
Related Manuals for Makita 6201DW
Summary of Contents for Makita 6201DW
- Page 1 IRPM) High Machine screw 6 m m '"4'' Model DC9700 Fast Charger Input A.C. only 50 Hz 60 Hz MODEL 6201D MODEL 6201DW With Fast Charger Dimensions x W x H) weight 57 m m mm x 19-318" 2-114" 9-9/16") 13.7...
-
Page 2: Safety Instructions
SAFETY INSTRUCTIONS WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT. - Page 3 14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16.
- Page 4 SAVE THESE INSTRUCTIONS This manual Length of Cord (Feet) AWG Size of Cord...
-
Page 5: Additional Safety Rules
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C 4OoC (104OF). or ABOVE 2. Do not attempt to use a step-up transformer, an engine generator or DC power receptacle. Do not allow anything to cover or clog the charger vents. 4. - Page 6 Installing or removing battery cartridge .Always switch off the tool before insertion or removal or the battery cartridge. To remove the battery cartridge, pull out the set plate on the tool and grasp both sides of the cartridge while withdrawing it from the tool.
- Page 7 Installing or removing driver bit or drill bit CAUTION : Always be sure that the tool is switched off and the battery cartridge i s removed before installing or removing the bit. To install the bit, push the sleeve up to- ward the "FREE"...
- Page 8 Switch action Tool speed is increased by increasing pres- sure on the trigger. To start the tool, simply pull the trigger. Release the trigger to stop. CAUTION : Before inserting the -attery cartridge into the tool, always check to see that the trigger switch actuates properly and returns to the "OFF"...
- Page 9 Adjusting fastening torque The fastenina toraue can be adiusted in six stages by turning the adjusting ring so that the pointer on the adjusting ring points t o a number on the tool body. The fastening torque is minimum when the pointer points to the number 1 and maximum when it points to the marking.
- Page 10 Drilling operation First, turn the adjusting ring so that the pointer on the adjusting ring points t o the marking. Then proceed as follows. Drilling in wood When drilling in wood, best results are obtained with wood drills equipped with screw.
-
Page 11: Maintenance
Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. - Page 12 ACCESSORIES CAUTION These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner.
- Page 13 F e b . - 2 5 - ' 9 2 CORDLESS DRIVER DRILL Model 6201D Note: The switch and other part configurations may differ from country t o country.
- Page 14 MODEL 6201D ,& I i k M DESCRIPTION Housing Set IWith Item Name Plate Pan Head Screw M4x22 IWith Washer1 Tapping Screw BT4x20 Hand Strap Plate Switch Lever Switch Lever Pan Head Screw M5x22 Keyless Drill Chuck 10 Spindle PI" 4 Bearing Retainer 14 Ball Bearing 6000LLB Stop Ring E-9...
- Page 15 MAKITA LIMITED O N E YEAR WARRANTY Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted t o be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.