Related Manuals for Honeywell 720P
Summary of Contents for Honeywell 720P
- Page 1 Honeywell 720P&D1 IR Vandal Dome Camera User’s Manual 14746 Document 800- Rev. A...
- Page 3 Honeywell Owner's Record The model and serial numbers are located at the bottom of device. Record these numbers in the spaces provided below. Refer to these numbers whenever you call upon your dealer regarding this product. Model No. ____________________ Serial No. ____________________ To prevent fire or shock hazard, do not expose the unit to rain or moisture.
-
Page 4: Declaration Of Conformity
Honeywell Declaration of Conformity This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. -
Page 5: Table Of Contents
Honeywell Contents Overview ............................ 1 Introduction ..........................1 Features ............................. 1 Minimum System Requirements ....................2 Package Contents ........................3 Connections ..........................4 Connector Cable (Option) ......................4 Connector board ......................... 6 Hardware Installation ........................ 9 Install the Camera in LAN ....................... 11 Preparation .......................... - Page 6 Honeywell Administrating the Device ...................... 26 System Setting .......................... 26 Network: Configure Network settings .................. 26 Camera: Adjust Camera parameters ................... 37 System: Configure and maintain system ................43 Video: Configure OSD, Overlay, Profile, and ROI ..............47 Audio: Audio parameters ..................... 52 User: Manage user name, password and login privilege ............
-
Page 7: Overview
PC. The live video can be uploaded to a website for the world to see. Features Sony Exmor™ image sensor • 720P : 720p / 1.3 Mega mode ; SVGA/D1 : 800x600 / D1 mode • 720P : 60fps in all resolutions ; SVGA/D1: 30fps in all resolution •... -
Page 8: Minimum System Requirements
Overview UPnP device discovery and NAT router transversal for easy installation • Dynamic IP Service, DIPS®, to search your IP camera from Internet easily • H.264, MPEG4 and MJPEG triple compression simultaneously • 12-profile encoder simultaneously • UDP / TCP / HTTP / HTTPS protocols selectable •... -
Page 9: Package Contents
Honeywell 2 Package Contents User can find the following items in the package: Item Descriptions 1. This camera is the main element of the product. 2. Accessories 3. User’s Manual CD provides important information and instructions for operating the Network Camera... -
Page 10: Connections
Connections 3 Connections There are two types. One is cabling with built-in connector board and the other one is with connector cable. Note that user must choose only one of these two configurations. The camera does not support both cabling at the same time. Connector Cable (Option) RJ45 LAN socket: Connect to PC or Hub/Switch. - Page 11 Honeywell In the LAN socket, there are two LEDs embedded: LAN LED (green color) This LED will be flashing while network accessing via Ethernet. Power LED (orange color) This LED is used to indicate whether DC power is on or not.
-
Page 12: Connector Board
Connections The Network Camera also provides composite video output. The video output function is only for easy installation to check view angle and focus. The output is not a Mega-pixel resolution. Furthermore, the video output is off by default. To turn on video, please refer to Setting\Camera\Picture chapter. - Page 13 Honeywell LAN LED (green color) This LED will be flashing while network accessing via Ethernet. Power (orange color) This LED is used to indicate whether DC power is on or not. In addition, this LED will be flashing while the wireless accessing of the Camera.
- Page 14 Connections The output power is 12VDC. This is used to support DI/DO devices. The output power is 12VDC/50mA maximum. DI/GND/DO/RS485 Interface of Digital input/output and RS485 AC24V Block Factory Default Reset This button is used to restore the all factory default settings. Sometimes restarting the device will make the system back to a normal state.
-
Page 15: Hardware Installation
Honeywell 4 Hardware Installation Use the provided L-wrench, loosen the tamper-resistant housing cover (with screws still attached on the cover). The unit has a factory installed side conduit entry and one may adjust the cables to back conduit entry according to installation requirement. - Page 16 Hardware Installation When the camera focus adjustment has been completed, use the provided L-wrench to fasten the tamper-resistant housing to the main body.
-
Page 17: Install The Camera In Lan
Honeywell 5 Install the Camera in LAN Plug an Ethernet cable into the Camera Connect an Ethernet cable to the LAN socket and attach it into the network. Connect the external power supply to Camera, if not powering by PoE Connect the attached power adapter to the DC power jack of the camera. -
Page 18: Preparation
Preparation 6 Preparation Search and Set up by IP Wizard II Once you installed the Camera on a LAN environment, you have two easy ways to search your Cameras by IP Wizard II or UPnP™ discovery. Here is the way to execute IP Wizard II to discover Camera’s IP address and set up related parameter in a Camera. -
Page 19: View
Honeywell View If IP Wizard II finds network devices, View button will be available. Please select the device you want to view and click the View button. Then you could see the video from camera directly. Furthermore you could double click the left button of mouse to link to the network... -
Page 20: Lan
Preparation In case you want to change the IP related parameters of wired interface, please select the device you want to configure and click the LAN button. Relative settings will be carried out as below. You could modify the relative settings of the selected device. Click “<<” button will quit the LAN setting procedure and click “>>”... - Page 21 Honeywell In case, you do not want to change username and/or password, then just click “Submit” button to perform your setting accordingly. Click “<<” button will go back to previous page. If you like to change username and/or password of the device, just click the check button.
-
Page 22: Wireless
Preparation Wireless This model does not support wireless function. Therefore, IP Wizard II disables this function automatically. ® UPnP of Windows XP, Vista or 7 UPnP™ is short for Universal Plug and Play, which is a networking architecture that provides compatibility among networking equipment, software, and peripherals. -
Page 23: Install The Device Behind A Nat Router
Honeywell Install the Device behind a NAT Router Once installed, the device is accessible on your LAN. To access the device from the Internet you must configure your broadband router to allow incoming data traffic to the device. If the device is installed on the LAN with a router, then it may get a dynamic IP address from the DHCP server. - Page 24 Preparation Type in your login name and password under “USERNAME” and “PASSWORD” textbox. For the first time use (default value), input the User Name: admin Password: admin That’s, type in “admin” on the “USERNAME” as a default name and type in “admin” on the PASSWORD textbox.
-
Page 25: Logging In As An Viewer
Honeywell Logging in as an Viewer If you log in the Camera as an ordinary User, “Setting” function will be not accessible. Logging in as an Administrator If you log in the Camera as the Administrator, you can perform all the settings provided by... -
Page 26: Operating The Network Camera
Operating the Network Camera 7 Operating the Network Camera Start-up screen will be as follow no matter an ordinary users or an administrator. ActiveX Control Monitor Image Section Full 2-Way Screen Audio Monitor Image Section The image shot by the device is shown here. The date and time are displayed at the top of the window if Text Overlay enabled. -
Page 27: Video Profile
Honeywell Video Profile The device supports multi-profile function for H.264, MEPG4 and MJPEG simultaneously. User can chose the proper and/or preferred profile which is listed here. Streaming Protocol User can select proper streaming protocol according to networking environment. Language The device could provide multiple languages to meet customer’s requirement. -
Page 28: Ptz Control
Operating the Network Camera PTZ Control Note that this function is enabled by “camera protocol” been set first. Click to display the following control panel: Camera direction Camera speed Preset Go tour Tour Auto pan Camera direction: Control camera up/down/left/right and home position. Camera speed: Choose the speed of Pan and Tilt. -
Page 29: Activex Control
Honeywell ActiveX Control The plug-in ActiveX control supports a lot of functions by clicking the left mouse button. Note that this feature only supports on the ActiveX control within Microsoft® Internet Explorer. On the ActiveX control icon, click the LeftMouseButton, then a menu pop-up. This menu provides features that are unique to the ActiveX control. -
Page 30: Snapshot
Operating the Network Camera Snapshot Click Snapshot to activate this function. Press Snapshot button to take a picture. The image file is saved as JPEG format into your local PC. Select Browser, the pop-up window to select the save path and file name prefix, select OK to continue. If you like to retrieve the saved image, select the file to display the saved image by using any one of graph editing tools. -
Page 31: Volume
Honeywell Volume Click Volume to activate this function. There are two control bars for speaker and microphone volume respectively. Scroll these control bars to adjust the audio attribute. Check the volume mute will mute the speaker output. About Click About to show this ActiveX information. -
Page 32: Administrating The Device
Administrating the Device 8 Administrating the Device System Setting This function is only available for user logged into Camera as administrator. Click on each menu name to display its setting page. Item Action Network Configure Network settings such as DHCP, DDNS, RTSP, PPPoE and UPnP Camera Adjust camera parameters, position, and set camera tour System... - Page 33 Honeywell MAC address: Displays the Ethernet MAC address of the device. Note that user can not modify it. Obtain IP address automatically (DHCP): DHCP: Stands for Dynamic Host Configuration Protocol. Enable this checked box when a DHCP server is installed on the network to issue IP address assignment.
- Page 34 Administrating the Device assign the second port number of http protocol, and the WAN users should follow the port number to login. If the http port is not assigned as 80, users have to add the port number in back of IP address. For example: http://192.168.0.100:8080. Therefore, the user can access the device by eitherhttp://xx.xx.xx.xx/, or http://xx.xx.xx.xx:xxxx/ to access the device.
-
Page 35: Ddns Service
Honeywell HTTPS: To enable or disable the HTTPS service here. Note that the HTTPS function of this device is not only encrypted the web content but also audio/video data. If the HTTPS is enabled, there is further option for “HTTP&HTTPS” or “HTTPS only”. In case, the “HTTPS only”... - Page 36 Administrating the Device DDNS: To enable or disable the DDNS service here. Server name: Choose one of the built-in DDNS servers. DDNSHost: The domain name is applied of this device. User name: The user name is used to log into DDNS. Password: The password is used to log into DDNS.
- Page 37 Honeywell Connect to a LAN by DHCP or Fixed IP • Access the device, enter Setting Network PPPoE as below • PPPoE: To enable or disable the PPPoE service here. User name: Type the user name for the PPPoE service which is provided by the ISP.
- Page 38 Administrating the Device RTSP Port: Choose the RTSP port. The RTSP protocol allows a connecting client to start a video stream. Enter the RTSP port number to use. The default value is 554. RTP Port: Specify the range of transmission port number of video stream. The default range is 50000 to 50999.
- Page 39 Honeywell UPnP is short for Universal Plug and Play, which is a networking architecture that provides compatibility among networking equipment, software, and peripherals. This device is an UPnP enabled Network Camera. If your operating system is UPnP enabled, the device will automatically be detected and a new icon will be added to “My Network Places.”...
- Page 40 Administrating the Device Bonjour: To enable or disable the Bonjour service here. Friendly Name: To show the friendly name of this device here. ONVIF: To enable or disable the ONVIF interface here. And select the ONVIF version to match client’s supported version. IP Filter You can enter different user’s IP address which are allowing enter or denying by the device.
- Page 41 Honeywell IP Notification In case the IP address is changed, system is able to send out an email to alert someone if the function is enabled. SMTP Notification (e-mail): If enable this function, then the “Send to“ and “Subject” fields need to be filled.
- Page 42 Administrating the Device TCP Server: Type the server name or the IP address of the TCP server. TCP Port: Set port number of TCP server. Message: The message will be sent to FTP server. HTTP Notification: If enable this function, then the fields below need to be filled. URL: Type the server name or the IP address of the HTTP server.
-
Page 43: Camera: Adjust Camera Parameters
Honeywell Proxy Login name: Type the user name for the HTTP Proxy. Proxy Login Password: Type the password for the HTTP Proxy. Custom parameter: User can set specific parameters to HTTP server. Message: The message will be sent to HTTP server. - Page 44 Administrating the Device White Balance: Auto: will adjust the white balance automatically. Hold: will hold the white balance. Iris/Exposure Control: Auto Iris: will adjust the DC Iris automatically. This Camera is built-in a DC-Iris lens. In case, the “Auto Iris” mode is selected, the Camera will control DC Iris automatically.
- Page 45 Honeywell Exposure Value: Exposure value is AE target value. This value is to adjust the integration, analog gain and digital gain to achieve the target brightness value (Exposure Value). This value is dependent to “Auto Exposure” only. Color Level: Large value will be colorful.
-
Page 46: Privacy Mask
Administrating the Device WDR: This function is to provide clear images even under back light circumstances. The higher “Strength” level will adjust contrast compensation stronger. Default Settings: Restore to factory image settings. Privacy Mask Use this page to specify privacy mask window 1 to window 8 and set the name and gray level for selected window. -
Page 47: Preset Setting
Honeywell This device can connect to a PTZ camera or speed dome camera and controls them thru RS485 interface. Camera Address: This is the camera ID set in PTZ camera or speed dome camera. Note that please DO NOT change the default value if unnecessary. If so, user needs to check and set value properly for both sides. -
Page 48: Tour Setting
Administrating the Device Tour Setting Up to 128 positions can be preset, and the camera can be programming to move to the preset position sequentially. Tour Name: The group name of the sequence of camera tour. The maximum number of camera tour is Running: Enable or disable this camera tour. -
Page 49: System: Configure And Maintain System
Honeywell Preset: Set the sequence of the tour. Maximum 16 points can be assigned. The selected preset position is added in the Sequence list from 1 to 16. Wait Time: Type a period of time during which the camera is to stay at each preset point, between 0 to 36000 seconds. - Page 50 Administrating the Device To turn on or off the Power LED (wireless LED if WLAN model). Log: User can check the system log information of the device, including the Main Info, Appended Info, Operator IP, and so on … Reload: Click this button;...
- Page 51 Honeywell Maintenance Hard Factory Default (Include the network setting): Recall the device hard factory default settings. Note that click this button will reset all device’s parameters to the factory settings (including the IP address). Factory Default (Except the network setting): The unit is restarted and most current settings are reset to factory default values.
- Page 52 Administrating the Device Firmware Upgrade: The device supports new firmware upgrade (the software that controls the operation in the device). Please contact your dealer for the latest version if necessary. Download the latest firmware file from our website or your dealer. Unzip this firmware file to binary file and store it into your PC.
-
Page 53: Video: Configure Osd, Overlay, Profile, And Roi
Honeywell Furthermore, the firmware upgrade procedure is always risky and do not try to upgrade new firmware if it’s not necessary. System Restart: The device is restarted without changing any of the network settings. It means the IP address of the device will not change after firmware upgrade. - Page 54 Administrating the Device In “User Defined Text” mode, user can overlay a text string onto camera image as below: The font style can be chosen in this page. Once the font type settled, click “Save” button to upload text to image. Coordinates: Set position of image on the video.
- Page 55 Honeywell Resolution: Size information of the uploaded bitmap file. Chroma Key (Background Color): Define the Chroma key of the uploaded bitmap file. Then user can set transparency of the bitmap. Transparency: Lower value will lower transparent. Value 0 means opacity.
- Page 56 Administrating the Device Rate Control: Defines the rate control method of this profile. There are three options: Constant Bit Rate (CBR), Variable Bit Rate (VBR), and Enhanced Variable Bit Rate (EVBR). For CBR, the video bit rate is between low to high bandwidth based on different resolutions. User can set the desired bit rate to match the limitation of bandwidth.
- Page 57 Honeywell Note that this function is not recommended for camera with PTZ/ePTZ actions. AOI means Area of Interest, Use this page to specify location and size of AOI windows. User can define maximum two ROI windows. And User can define image quality level -10 to 10...
-
Page 58: Audio: Audio Parameters
Administrating the Device Audio: Audio Parameters Audio: To enable or disable audio function Audio Type: To select audio codec Audio Mode: To select Simplex or Full duplex (2-way audio) mode Input Gain: To adjust gain of input audio Output Gain: To adjust gain of output audio User: Manage User Name, Password and Login Privilege Use this menu to add, update, or remove the usernames and passwords of the Administrator... - Page 59 Honeywell Viewer login: Select “Anonymous” to allow any one viewing the video once connected. Otherwise, only users in database can view the video after login. Access Right: Administrator can access every function in this device. However, Viewers only can view the video and access limited function.
- Page 60 Administrating the Device Protocol ONVIF: To enable or disable the ONVIF interface here. And select the ONVIF version to match client’s supported version. ONVIF is a global and open industry forum with the goal to facilitate the development and use of a global open standard for the interface of physical IP-based security products. In IP products video surveillance other words, to create a standard for how...
-
Page 61: E-Mail: Setup E-Mail Configuration
Honeywell SNMP: To enable or disable the SNMPv1 or SNMPv2c here. And set Read community and Write community. E-Mail: Setup E-Mail configuration User may setup SMTP mail parameters for further operation of Event Schedule. That’s, if users want to send the alarm message out, it will need to configure parameters here first and also add at least one event schedule to enable event triggering. -
Page 62: Event Detection
Administrating the Device Authentication User name: Type the user name for the SMTP server if Authentication is Enable. Authentication Password: Type the password for the SMTP server if Authentication is Enable. E-mail From: Type the sender’s E-mail address. This address is used for reply e-mails. E-mail To: Type the receiver’s e-mail address. -
Page 63: Camera Tampering
Honeywell Included or Excluded Window: These windows can be specified as Included or Excluded type. Included windows target specific areas within the whole video image Excluded windows define areas within an Include window that should be ignored (areas outside Include windows are automatically ignored) Name: Name of the specified motion window. -
Page 64: Storage: Status And Configuration Of Sd Card And Samba Server
Administrating the Device Note that this function is not recommended for camera with PTZ/ePTZ actions. Audio Detection Audio detection alarm can be used as a complement to motion detection. Since audio detection can react to events in areas too dark for the video motion detection functionality to work properly. -
Page 65: Samba Server
Honeywell Enable automatic disk cleanup: Delete old recorded files while the conditions are reached as below. Remove recordings order than: Delete old files by days. Remove oldest recordings when disk is: Delete old files by left capacity. Lock disk Lock the SD card. Once SD card is locked, all files can’t be deleted. -
Page 66: Continuous Recording
Administrating the Device Host: Type the SAMBA server domain name or the IP address of the SMTP server. Share: Type the share folder of remote SAMBA server which the camera will upload files to this space. User name: Type the user name for the remote SAMBA server. Password: Type the password for the remote SAMBA server. -
Page 67: Recording List: Files List Inside The Sd Card Or Samba Server
Honeywell Continuous Recording: Enable or disable this function. Record File Type: Choose a video profile to record. DISK: Save recorded files to SD card or remote SAMBA server. Path: Define the folder path for the recorded files. Restart: Be careful, click this button will delete all continuous files recorded in SD card or remote SAMBA server. -
Page 68: Event Server: Setup Ftp/Tcp/Http/Samba Server Configuration
Administrating the Device Continuous Recording List This page only shows the continuous recording files which stored in SD card or remote SAMBA server. User may play or delete the selected file. Event Server: Setup FTP/TCP/HTTP/SAMBA Server Configuration FTP Server You may setup FTP parameters for further operation of Event Schedule. That’s, if users want to send the alarm message to an FTP server, it will need to configure parameters here and also add at least one event schedule to enable event triggering as SMTP. - Page 69 Honeywell Name: User can specify multiple FTP paths as wish. Therefore, user needs to specify a name for each FTP setting. FTP Server: Type the server name or the IP address of the FTP server. Test: Check the FTP server whether this account is available or not.
-
Page 70: Tcp Server
Administrating the Device TCP Server In addition to send video file to FTP server, the device also can send event message to specified TCP server. Name: User can specify multiple TCP servers as wish. Therefore, user needs to specify a name for each TCP server setting. - Page 71 Honeywell Name: User can specify multiple HTTP servers as wish. Therefore, user needs to specify a name for each HTTP server setting. URL: Type the server name or the IP address of the HTTP server. Test: Check the HTTP server whether it is available or not.
- Page 72 Administrating the Device Proxy Port: Set port number of Proxy. SAMBA Server The device also can send event recording video files to specified SAMBA server. Name: User can specify multiple HTTP servers as wish. Therefore, user needs to specify a name for each HTTP server setting.
-
Page 73: Event Schedule: Configure The Event Schedule
Honeywell Event Schedule: Configure the event schedule Setting This menu is used to specify the schedule of Event or Schedule Trigger and activate the some actions provided by this device. Where the Schedule Trigger will be activated by user-define interval without event happened. - Page 74 Administrating the Device Select event trigger Enable time: start from 00:00 to 24:00 every day Trigger by: Motion Area (Added in Object Detection page) Action : Send FTP (Add in Event Server -> FTP Server page) Example 2: Send file to E-Mail server by motion triggered from Friday 18:00 to Saturday 06:00 Select event trigger.
- Page 75 Honeywell Example 3: Enable Voice Alert every 10-minute during 18:00 to 24:00 from Monday to Friday. Type: Select schedule trigger and interval is 10-minute. Enable time: Select Monday to Friday, and set start time from 18:00 and keep work in 6 hours.
- Page 76 Administrating the Device Record User can choose the type of record file for event or schedule application. Record File Type: Choose a profile to record. Record File Prefix: Define the prefix of recorded filename.
-
Page 77: Port Status
Honeywell Pre-Trigger Duration: Define the maximum duration of pre-alarm. Best Effort Duration: Define the best effort duration of post-alarm. Max File Size: Define the maximum buffer size of record file. Port Status User can check the status of digital input and output (DIDO). -
Page 78: Appendix A: Alarm I/O Connector
Appendix A: Alarm I/O Connector 9 Appendix A: Alarm I/O Connector Some features of the Camera can be activated by the external sensor that senses physical changes in the area Camera is monitoring. These changes can include intrusion detection or certain physical change in the monitored area. - Page 79 Honeywell Video out Composited video output 12VDC out DC 12V output (50mA maximum) Digital signal input Digital ground Digital signal output RS485+ RS485 data + RS485- RS485 data - User can refer to the schematic below to make a proper connection between I/O connector and external sensor and output device.
- Page 80 Appendix A: Alarm I/O Connector CONNECTED TO THE EXTERNAL I/O THAT EXCEEDS ITS ELECTRICAL CAPABILITY.
-
Page 81: Appendix B: Troubleshooting & Frequently Asked Questions
Honeywell 10 Appendix B: Troubleshooting & Frequently Asked Questions Question Answer or Resolution Features The device utilizes H.264, MPEG4 and MJPEG triple compression to providing The video and audio codec high quality images. Where H.264 and MPEG4 are standards for video is adopted in the device. - Page 82 Appendix B: Troubleshooting & Frequently Asked Questions Make sure that your Internet Explorer is version 8.0 or later. If you are Internet Explorer does not experiencing problems, try upgrading to the latest version of Microsoft’s Internet seem to work well with the Explorer from the Microsoft webpage.
- Page 83 Honeywell configured properly and then try reloading the device’s home page. Most likely, the ActiveX control did not download and install correctly. Check your Internet Explorer security settings and then close and restart Internet Explorer. Try to browse and log in again.
- Page 84 Appendix B: Troubleshooting & Frequently Asked Questions Cannot play the recorded Have installed Microsoft®’s DirectX 9.0 or later and use the Windows Media AVI file Player 11.0 or later to play the AVI files recorded by the Device. In addition media player, VLC is another option to play AVI file.
-
Page 85: Appendix C: Ping Ip Address
Honeywell 11 Appendix C: PING IP Address The PING (stands for Packet Internet Groper) command is used to detect whether a specific IP address is accessible by sending a packet to the specific address and waiting for a reply. It’s also a very useful tool to confirm the device installed or if the IP address conflicts with any other devices over the network. -
Page 86: Appendix D: Bandwidth Estimation
The required bandwidth depends on content of video source. The slow motion video will produce smaller bit rate generally and fast motion will produce higher bit rate vice versa. Actual results generated by the device may be varying. Bandwidth Estimation for 720P Camera Image Rate Control Average bit rate for H.264... -
Page 87: Appendix E: Specifications
Honeywell 13 Appendix E: Specifications 720P Vandal Dome Network Camera Camera Image Device Sony Exmor image sensor Effective Pixels 1280 x 720 pixels Lens Vari-focal lens: f 3.3-12mm with auto Iris and ICR Angle Pan: 0 ~270 , Tilt: 0... - Page 88 Appendix E: Specifications Camera tampering Audio detection Digital input Motion 10-zone video motion detection with included or excluded options Detection File upload via FTP, SAMBA, SD card or email Notification via email, HTTP, and TCP Alarm Events External output activation Go to PTZ preset position Audio alerting output Video Buffer...
- Page 89 Honeywell Privacy Masks Text, time and date overlay Overlay image on video Streaming Simultaneously multi-profile streaming Streaming over UDP, TCP, HTTP, or HTTPS M-JPEG streaming over HTTP (server push) Controllable frame rate and bandwidth Constant and variable bit rate (MPEG4 / H.264)
- Page 90 Appendix E: Specifications Software Search & Installation IP Wizard II...
-
Page 91: Appendix F: Configure Port Forwarding Manually
Honeywell 14 Appendix F: Configure Port Forwarding Manually The device can be used with a router. If the device wants to be accessed from the WAN, its IP address needs to be setup as fixed IP address, also the port forwarding or Virtual Server function of router needs to be setup. - Page 92 Appendix F: Configure Port Forwarding Manually Your WAN IP Address will be listed here. Note: Because a dynamic WAN IP can change from time to time depending on your ISP, you may want to obtain a Static IP address from your ISP. A Static IP address is a fixed IP address that will not change over time and will be more convenient for you to use to access your camera from a remote location.
- Page 93 Honeywell Important: Some ISPs block access to port 80. Be sure to check with your ISP so that you can open the appropriate ports accordingly. If your ISP does not pass traffic on port 80, you will need to change the port the camera uses from 80 to something else, such as 8080. Not all routers are the same, so refer to your user manual for specific instructions on how to open ports.
-
Page 94: Appendix G: Power Line Frequency
Appendix G: Power Line Frequency 15 Appendix G: Power Line Frequency COUNTRY VOLTAGE FREQUENCY COMMENTS *Neutral and line wires are reversed from that Argentina 220V 50 Hz used in Australia and elsewhere. *Outlets typically controlled by adjacent switch. Though nominal voltage has been officially Australia 230V* 50 Hz... - Page 95 Honeywell United States of America 120V 60 Hz...
- Page 96 Email: [email protected] https://www.asia.security.honeywell.com India office Honeywell Security Unitech Trade Center, 5th Floor, Sector 43, Block Taiwan office C, Sushant Lok Phase - 1, Gurgaon - 122 002 10F, 168 Lien Cheng Road, Chung Ho City, Taipei, Taiwan R.O.C. Tel: (91) 124 4975000...