Summary of Contents for Soundwin SP110
- Page 1 SP110 Skype Phone Adapter User Manual Version 1.0.10 Default Login Detail WAN IP Address: DHCP LAN IP Address: http://10.0.0.1 Password: 1234...
-
Page 2: Table Of Contents
Table of Contents INTRODUCE ........................3 1.1 O VERVIEW 1.2 I NTRODUCTION 1.3 F LED I & R RONT ANEL NDICATORS ANELS 1.4 S PECIFICATION INSTALLATION AND SETUP ..................... 5 2.1 P ACKAGE ONTENT 2.2 H ARDWARE NSTALLATION 2.3 Q UICK TART NETWORK SETTING (WAN) ..................... -
Page 3: Introduce
Skype to Skype calls, Skype to Mobile and landline calls. No PC required The SP110 Skype Phone adapter lets you make and receive Skype calls at any time, without having your computer on. Speed Dial List The SP110 Skype Phone adapter can store up to 100 speed dials of Skype contacts. -
Page 4: Specification
Status Description Power SP110 is power on SP110 is power off On / Flashing Ethernet cable was connected Ethernet not connected to PC On / Flashing Ethernet cable was connected Waiting for network connection Login Login Skype account successfully. Login Skype account fail... -
Page 5: Installation And Setup
The contents for the final product might change a little bit. SP110 Package (SP110) (RJ45 cable) ( RJ11 telephone line) (Power adapter) The SP110 packet contents: SP110 RJ-45 cable line RJ-11 telephone line AC Power Adapter (0.5A) Quick Guide 2.2 Hardware Installation... - Page 6 Port Description: Power Reset WAN Phone Line Item Port Description FXS(Foreign Exchange FXS port can be connected to analog Station) telephone sets Line Connect to CO line with RJ-11(Gray) analog line. WAN(Wide Area Network) Connect to the network with an Ethernet cable.
- Page 7 Ethernet hub or switch.
-
Page 8: Quick Start
For LAN: IP: 10.0.0.1 Subnet mask: 255.255.255.0 How to configure SP110? 1. Configure your PC or NB to the same subnet with SP110. 2. Use web browser (IE/Firefox) link to url: http://10.0.0.1 3. Select language: English or Chinese 4. Login password: 1234 5. -
Page 9: Network Setting (Wan)
WAN Setting is used to connect to your ISP (Internet Service Provider). The WAN settings are provided to you by your ISP and often times referred to as "public settings". Please select the appropriate option for your specific ISP. SP110 support three methods for Internet access: Static IP ... -
Page 10: Dhcp Client
■IP Address: Check with your ISP provider. ■Subnet Mask: Check with your ISP provider. ■Default Gateway: Check with your ISP provider. DHCP client Dynamic Host Configuration Protocol (DHCP), Dynamic IP (Get WAN IP Address automatically). If you are connected to the Internet through a Cable modem line, then a dynamic IP will be assigned. - Page 11 ■PPPoE User name: Enter username provided by your ISP. ■PPPoE Password: Enter password provided by your ISP.
-
Page 12: Skype Account Setting
Skype Account Setting 4.1 Skype Account Setting When you set up the SP110, firs time you’ll start with Wizard pages. After that, when you log in the SP110 again, you’ll see the basic setting. You can change the Skype account and call mode (Skype First Mode or Landline First mode) here. - Page 13 of phone book as below. Dial ＊0 to call abc123 account.
-
Page 14: Advance Setting
When you select the call mode as Skype first, you would like to dial out the landline number or mobile number by Line port of SP110, you need to dial ＃before the number, if you don’t want to dial ＃before the number, you can setup the landline dial plan list. -
Page 15: Lan Setting
5.3 LAN Setting IP settings of the LAN (Local Area Network) interface for the device. The LAN IP address is private to your internal network and cannot be seen on the Internet. You can change the LAN IP address if needed. The default IP address is 10.0.0.1 with a subnet mask of 255.255.255.0. -
Page 16: Update System
5.4 Update System This page allows you upgrade the SP110 firmware to new version. Please note, do not power off the device during the upload because it may cause the system crash. 5.5 Set to Default This function allows SP110 return to factory default: WAN as DHCP LAN ip is 10.0.0.1... -
Page 18: Q & A
Q & A? Q: Why I use web browser link to http://10.0.0.1, but the log in page of SP110 can’t display? A: Please make sure the hardware installation is correct, please check the status of internet connection, please go to [Start][Control Panel][Network Connection][Local Area Connection], check if the status is connected, if not, please...