Summary of Contents for Halley BCG1E34F
- Page 1 BCZ3200DL / BCZ3200DW OWNER’S MANUAL BRUSH CUTTERS BCG1E34F BCG1E40F-5 (ST-BC415B) GB-1 GB-1...
- Page 2 FACTORY'S CE CERTIFICATES: BCG1E34F (Factory's No. HLG1E34F) BCG1E40F-5 (Factory's No. HLG1E40F-5) EXPLANATION OF SYMBOLS AND SAFETY WARNINGS WARNING!!! RISK OF DAMAGING HEARING IN NORMAL CONDITIONS OF USE, THIS MACHINE MAY INVOLVE A DAILY LEVEL OF PERSONAL EXPOSURE TO NOISE FOR THE OPERATOR EQUAL TO OR GREATER THAN...
-
Page 3: Table Of Contents
Contents SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and 1. Parts location ..........3 for this reason you are requested to read all such instructions 2. -
Page 4: Specifications
2. Specification BCG1E34F/ BCG1E40F-5 Dry weight....................5.7 / 7.2 kg Engine Model.................... 1E34F/1E40F-5 Displacement................25.4CC / 42.7CC Engine power................750 W / 1250 W Maximum speed of cutter head/Engine speed ( min-1).....6000 / 8000 Engine idle speed ( min-1).................3000 Centrifugal speed(min-1).................4100 Fuel................ -
Page 5: For Safe Operation
5. For safe operation b. At night, at times of heavy fog, 1. Read this manual carefully until or at any other times when you completely understand and your field of vision might be follow all safety and operating limited and it would be diffi- instructions. - Page 6 5. For safe operation BEFORE STARTING ensure that neither the cutting THE ENGINE part nor the throttle come into 1. The area within a perimeter of contact with any obstacle when 15 m (50 ft) of the person using the engine starts. the product should be considered a hazardous area into which no WARNING...
- Page 7 5. For safe operation could result in serious burns or elec- HANDLING FUEL trical shock. 1. The engine of the product is designed to run on a mixed fuel, which con- • IF SOMEONE COMES tains highly flammable gasoline. 1. Guard against hazardous situa- Never store cans of fuel or refill tions at all times.
-
Page 8: Set Up
6. Set up - Position the blade (C/4), thrust washer (C/5) and finally the floating disc (C/6) as shown. INSTALLING HANDLE (BCG1E34F) • Mount the handle to the shaft tube and clamp it at a - Screw down the locknut (C/7) and tighten it by turning the location that is comfortable to you. -
Page 9: Fuel
7. Fuel FUEL 4. Pour in the rest of gasoline and agitate again for at least one minute. As some oils may be difficult to agitate depending on oil ingredients, sufficient agi- • Gasoline is very flammable. Avoid smoking or tation is necessary for the engine to last long. -
Page 10: Operation
8. Operation STARTING ENGINE WARNING The product is equipped with a centrifugal clutch WARNING mechanism, so the cutting attachment begins to ro- The cutting head will start rotating upon the engine tate as soon as the engine is started by putting the starts. - Page 11 8. Operation ADJUSTING THROTTLE CABLE METAL BLADE USAGE • The normal play is 1 or 2 mm when measured at the 1. Check the nut to fasten the blade and be sure the nut carburetor side end. Readjust with the cable adjuster has no fault, and no abrasion.
- Page 12 8. Operation CUTTING METHOD c. Be extra prepared for bounce if you must cut where (a) Use the front left side cutting. you cannot see the blade making contact such as in (b) Guide the blade from your right to left with it tilted areas of dense growth.
-
Page 13: Maintenance
8. Operation 3. Use a slow, deliberate action to cut heavy growth. ADJUSTING THE LINE LENGTH The rate of cutting motion will depend on the material • Your brush cutter is equipped with a semi- auto type being cut. Heavy growth will require slower action than nylon line head that allows the operator to advance will light growth. - Page 14 9. Maintenance REFILLING TRIMMING LINE WARNING 1. For replacement line, use a diameter of 2.4mm(.095in). • Make sure that the engine has stopped and is cool The spool is capable for a line upto 6m(20ft) on the before performing any service to the machine. Con- 10cm(4”) head.
-
Page 15: Storage
9. Maintenance • When checking the machine to make sure that it IMPORTANT is okay before using it, check the area around the • Note that using any spark plug other than those des- muffler and remove any wood chips or leaves ignated may result in the engine failing to operate prop- w h i ch h av e a t t a ch e d t h e m s e l v e s t o t h e erly or in the engine becoming overheated and dam-... -
Page 16: Troubleshooting Guide
11. Troubleshooting guide Case 1. Starting failure CHECK PROBABLE CAUSES ACTION → incorrect fuel → drain it and use correct fuel fuel tank → fuel filter is clogged → clean fuel filter → out of normal range → adjust to normal range carburetor adjustment screw →...