1. Manuals
  2. Brands
  3. Sony Manuals
  4. Monitor
  5. HMD-V200
  6. Service manual

Sony TRINITRON HMD-V200 Service Manual

Color graphic display
Hide thumbs Also See for TRINITRON HMD-V200:
Table of Contents

Quick Links

SERVICE MANUAL

CRT
0.24 mm aperture grille pitch
17 inches measured diagonally
90-degree deflection
FD Trinitron
Approx. 327 × 243 mm (w/h)
Viewable image size
(12
16.0" viewing image
Resolution
Horizontal: Max. 1280 dots
Vertical: Max. 1024 lines
Approx. 312 × 234 mm (w/h)
Standard image area
(12
Deflection frequency*
Horizontal: 30 to 70 kHz
Vertical: 48 to 120 Hz
Speaker
1W + 1W (max.)
Headphones output
Stereo minijack, impedance 8Ω
Audio input
3.5 mm stereo miniplug, input
level 0.7 Vrms typical
AC input voltage/current 100 to 120 V, 50 – 60 Hz, 1.8 –
1.5 A
Power consumption
Max. 150 W
Approx. 411.5 × 390 × 474 mm
Dimensions
(w/h/d) (16
inches) when tilted at a 25°
angle
Mass
Approx. 22 kg (48 lb 8 oz)
Plug and Play
DDC1/DDC2B
Supplied accessories
Power cord (1)
Windows Monitor Information
Disk (1)
Warranty card (1)
Notes on cleaning the screen's
surface (1)
This instruction manual (1)
MICROFILM
SPECIFICATIONS
7
× 9
5
/
/
inches)
8
8
× 9
3
1
/
/
inches)
8
4
× 15
× 18
1
3
3
/
/
/
4
8
4
TRINITRON
HMD-V200
Canadian Model

Preset mode timing table

No. Resolution
Horizontal
(dots × lines)
Frequency
640 × 400
1
31.5 kHz
640 × 480
2
31.5 kHz
640 × 480
3
43.3 kHz
800 × 600
4
37.9 kHz
800 × 600
5
46.9 kHz
1024 × 768
6
60.0 kHz
1024 × 768
7
68.7 kHz
1152 × 864
8
54.9 kHz
1280 × 1024
9
64.0 kHz
* Recommended horizontal and vertical timing condition
• Horizontal sync width duty should be more than 4.8%
of total horizontal time or 0.8 µsec, whichever is larger.
• Horizontal blanking width should be more than 2.5
µsec.
• Vertical blanking width should be more than 450 µsec.
Design and specifications are subject to change without
notice.
COLOR GRAPHIC DISPLAY
®
US Model
Chassis No. SCC-L28B-A
HIT
CHASSIS
Vertical
Graphics
Frequency
Mode
70 Hz
MCGA
60 Hz
VGA
85 Hz
VESA
60 Hz
VESA
75 Hz
VESA
75 Hz
VESA
85 Hz
VESA
60 Hz
ATI
59 Hz
VESA
Table of Contents
loading

Related Manuals for Sony TRINITRON HMD-V200

Summary of Contents for Sony TRINITRON HMD-V200

  • Page 1: Service Manual

    HMD-V200 SERVICE MANUAL US Model Canadian Model Chassis No. SCC-L28B-A CHASSIS SPECIFICATIONS 0.24 mm aperture grille pitch Preset mode timing table 17 inches measured diagonally 90-degree deflection FD Trinitron No. Resolution Horizontal Vertical Graphics Approx. 327 × 243 mm (w/h) (dots ×...

  • Page 2: Power Led

    HMD-V200 DIAGNOSIS Failure Power LED HV Failure Blink Amber (On 0.5 sec, Off 0.5 sec) H Stop or V Stop (Included S-Cap), Blink Amber (On 1.5 sec, Off 0.5 sec) Thermal Failure ABL Failure Blink Amber (On 0.5 sec, Off 1.5 sec) Aging/Over Ride Blink Green (On 0.5 sec, Off 0.5 sec) ..
  • Page 3 VIEWS AND IN THE PARTS LIST ARE CRITICAL FOR Parts on Set SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS AP- PEAR AS SHOWN IN THIS MANUAL OR IN SUPPLE- MENTS PUBLISHED BY SONY. CIRCUIT ADJUST- MENTS THAT ARE CRITICAL FOR SAFE OPERATION 0.15 µ...

  • Page 4: Table Of Contents

    HMD-V200 TABLE OF CONTENTS Section Title Page 1. GENERAL ..............1-1 2. DISASSEMBLY 2-1. Cabinet Removal ..........2-1 2-2. A Board Removal ..........2-1 2-3. D Board Removal ..........2-2 2-4. G Board Removal ..........2-2 2-5. Service Position ............ 2-2 2-6.

  • Page 5: General

    The operating instructions mentioned here are partial abstracts SECTION 1 from the Operating Instruction Manual. The page numbers of the Operating Instruction Manual remein as in the manual. GENERAL Precautions Positioning your monitor Identifying parts and controls This monitor is ergonomically designed to reduce eye and muscle See the pages in parentheses for further details..
  • Page 6 x Connecting to a Macintosh Step 2: Connect the power cord Step 3: Turn on the monitor and Setup Use a Macintosh adapter (not supplied). computer With the monitor and computer switched off, first connect the Macintosh or Before using your monitor, check that the following accessories power cord to the monitor, then connect it to a power outlet.
  • Page 7 x Using the buttons 6 COLOR (page 10) Adjusting the brightness and COLOR Customizing Your Monitor Select the COLOR menu to adjust 1 1 0 0 0 K Press the MENU button. contrast the picture’s color temperature. You 9 3 0 0 K 6 5 0 0 K The main MENU appears on the screen.
  • Page 8 Enlarging or reducing the picture Adjusting the color of the picture Adjusting the quality of the picture Additional settings (OPTION) (ZOOM) (COLOR) (SCREEN) You can increase the bass level of the speakers, manually degauss (demagnetize) the monitor, change the menu position, lock the This setting is stored in memory for the current input signal.
  • Page 9 Selecting the on-screen menu language Technical Features Troubleshooting (LANGUAGE) English, French, German, Spanish, Italian, and Japanese versions of the on-screen menus are available. The default setting is Before contacting technical support, refer to this section. Preset and user modes English. To change the menu language, first press the control If thin lines appear on your screen button up or down to select...
  • Page 10 Install the Windows Monitor Information Disk (page 7) and select this monitor Displaying this monitor’s name, serial number, If the problem persists, call your authorized Sony dealer and give (“HMD-V200”) from among the Sony monitors in the Windows 95/98 monitor selection the following information. and date of manufacture.
  • Page 11 Count the number of seconds between orange flashes of the 1 (power) indicator and inform your authorized Sony dealer of the monitor’s condition. Be sure to note the model name and serial number of your monitor. Also note the make and...
  • Page 12 MEMO ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○...

  • Page 13: Disassembly

    HMD-V200 SECTION 2 DISASSEMBLY 2-1. CABINET REMOVAL EMI shield Eight screws (+BVTT 3 x 8) Three screws (+PSW M3 x 8) Two claws Beat the both sides of the cabinet a little more strongly at once like pulling to back and remove two clawas.

  • Page 14: D Board Removal

    HMD-V200 2-3. D BOARD REMOVAL Two screws (+BVTT 4 x 8) A block D block (Slide and remove in arrow order A and B.) Two hooks Two screws Four screws (+BVTT 4 x 8) Screw (+BVTT 3 x 8) (+BVTP 3 x 12) D board Frame (R) 2-4.

  • Page 15: Bezel Assembly, J, H And M Boards Removal

    HMD-V200 2-6. BEZEL ASSEMBLY, J, H AND M BOARDS REMOVAL * Do not lean the body after remove bezel assembly cause of chassis are susceptible to distort. Four screws Screw (Tapping screw 5) (+BVTP 3 x 12) Two claws Two screws (+BVTP 4 x 16) J bracket J board...

  • Page 16: Picture Tube Removal

    HMD-V200 2-7. PICTURE TUBE REMOVAL Four screws C block (Tapping screw 5) Remove the connectors after removed A, D and G blocks. Two screws * Cause of bottom shields are susceptible (+BVTP 4 x 16) to distort as a precaution after remove D and G blocks.

  • Page 17: Harness Location

    HMD-V200 2-8. HARNESS LOCATION M board Speaker Speaker H board CN1705 CN1703 CN1801 CN1704 CN1702 CN1601 J board 8pin 2pin AC inlet CN1300 CN5607 CN609 CN601 CN902 CN905 CN5202 CN5200 CN5605 CN908 CN907 CN903 CN904 CN610 CN503 CN5204 CN906 CN501 CN604 D board CN603...

  • Page 18: Safety Related Adjustment

    HMD-V200 SECTION 3 SAFETY RELATED ADJUSTMENT • HV Protector Circuit Check When replacing or repairing the shown below table, the following operational checks must be performed as a Confirm that the voltage between cathode of D517 on D safety precaution against X-rays emissions from the unit. board and GND is more than 32.0 V DC and Using ex- ternal DC Power Supply, apply the voltage shown below Part Replaced (...

  • Page 19: Adjustments

    HMD-V200 SECTION 4 ADJUSTMENTS Connect the communication cable of the computer to the connector located on the D board on the monitor. Run the service software and then follow the instruction. 1-690-391-21 A-1500-819-A 3-702-691-01 Interface Unit Connector Attachment IBM AT Computer To BUS CONNECTOR as a Jig D-sub...
  • Page 20 HMD-V200 • Convergence Rough Adjustment • Convergence Specification 1. Enter the white crosshatch signal (white lines on black). 2. Adjust roughly the horizontal and vertical convergence at four-pole magnet. MODE All mode 3. Adjust roughly HMC and VMC at six-pole magnet. 0.20 mm 0.24 mm •...

  • Page 21: Diagrams

    SECTION 5 DIAGRAMS 5-1. BLOCK DIAGRAMS CN316 L IN G BOARD R IN CN5200 CN1002 TO FBT FOCUS A BOARD CN315 CN311 R IN L IN IC001 IC002 RGB DRIVE, OSD MIX RGB OUT CN307 CN1001 CN317 B GND B IN B IN B OUT BLUE...
  • Page 22 IC902 DEF CONROL IC901 CPU T505 HST CN904 IC501 PWM CONTROL KEY SCAN BUFF LED 1 LED RED T503 LED DRIVE Q901, 902 LED 2 LED GREEN BUFF Q521 SIRCS H BOARD CN1801 KEY SCAN CN903 BUFF DF AMP V DF Q505 Q504 C SYNC...
  • Page 23 IC5200 E-VOL/TONE CONT IC5202 IC5201 BUFF AUDIO POWER AMP CN5200 CN5202 L BUFF L IN L IN L OUT +IN 1 OUT 1 +L IN L OUT L OUT Q5201 -L IN R BUFF OUT 2 R IN R IN R OUT +IN 2 +R IN...

  • Page 24: Frame Schematic Diagram

    5-2. FRAME SCHEMATIC DIAGRAM SIGNAL IN (PIG-TAIL) HD 15 CN317 CN1001 BGND BLUE :S-MICRO BOARD IN GGND GREEN CN307 RGND :S-MICRO (CRT CONNECTOR) HOSTGND HEATER HEATER CN310 DDCSDA CN311 CN1002 DDCSCL :LARGE :DIP :S-MICRO V901 CN1003 PICTURE TUBE CN304 :DIP :TUB CN301 1.2KV...

  • Page 25: Circuit Boards Location

    5-3. CIRCUIT BOARDS LOCATION 5-4. SCHEMATIC DIAGRAMS AND PRINTED • Divided circuit diagram WIRING BOARDS One sheet of D, A and G boards circuit diagram are divided Note: into two sheets, each having the code D-a to D-b (A-a to •...
  • Page 26 (1) Schematic Diagram of A (a, b) Board • Divided circuit diagram One sheet of A board circuit diagram is divided into two sheets, each having the code A-a to A-b . For example, the destination ab1 on the A-a sheet is connected to ab1 on the A-b sheet.
  • Page 27 IC001 TO:C SHIELD CXA2067S IC002 CN312 VIDEO LM2405T-C R097 CONTROL AMP RGB OUT • Divided circuit diagram :DIP PIN :CHIP VDET One sheet of A board circuit diagram is divided into two R098 L012 C049 22µH 0.1 25V B:CHIP :CHIP R304 sheets, each having the code A-a to A-b .
  • Page 28 VIDEO — A BOARD — • A BOARD SEMICONDUCTOR LOCATION D006 – D007 – D008 – IC001 C–3 D014 – IC002 C–2 D015 IC003 D–4 D016 IC004 D–1 D017 IC005 C–1 D018 – IC006 C–5 D019 – IC700 A–1 D101 D104 –...
  • Page 29 — D BOARD — DEFLECTION • D BOARD SEMICONDUCTOR LOCATION D517 B–3 – D518 E–4 – D520 C–5 – IC501 C–2 D521 C–5 – IC502 A–3 D522 C–2 – IC503 E–5 D523 C–2 – IC900 B–2 D524 D–4 – IC901 B–2 D525 D–4...

  • Page 30: Schematic Diagram Of A Board

    (2) Schematic Diagram of D (a, b) Board TO A BOARD TO A BOARD TO H BOARD • Divided circuit diagram CN306 CN309 CN1801 One sheet of D board circuit diagram is divided into two sheets, each having the code D-a to D-b . For example, the destination ab1 on the D-a sheet is connected to ab1 on the D-b sheet.
  • Page 31 ab13 ab9 ab15 ab1 ab14 ab11 ab12 ab10 (DEFLECTION) -15V +15V TO G BOARD CN612 +12V +150V +150V TO G BOARD CN611 • Divided circuit diagram One sheet of D board circuit diagram is divided into two D1404 MA111-TX -14.2 sheets, each having the code D-a to D-b .

  • Page 32: Schematic Diagrams Of C, H, J And M Boards

    (3) Schematic Diagrams of C, H, J and M Boards D BOARD FBT(T501) J1001 FGND C1001 0.01 V901 • C BOARD CN1702 SG1001 PICTURE TUBE (HEAD-PHONE,AUDIO) :TUB WAVEFORMS R1001 TO G BOARD 10 9 FB1001 R1702 1/2W CN5607 J1703 C1002 C1705 R1701 JACK...
  • Page 33 CRT CONNECTOR USER CONTROL HEAD-PHONE, AUDIO AC SW — C BOARD — — M BOARD — — H BOARD — — J BOARD — J BOARD Terminal name of semiconductors in silk screen printed circuit ( Ref. Q1701, Q1702 D1703, D1704 : Refer to Terminal name of semiconductors in silk screen printed circuit (see page 5-10) 5-26...

  • Page 34: Schematic Diagram Of G Board

    (4) Schematic Diagrams of G (a, b) Boards REMOTE ON/OFF REMOTE ON/OFF (POWER) R684 AUDIO12V 1/4W IC611 IC608 SE-M140 PC123FY2 REMOTE INTERFACE R679 R678 R685 2.2M 2.2M 220k 1/2W 1/2W 1/4W C683 IC605 D606 0.001 CN608 Q604 MTZJ-T-77-4.7B PC123FY2 2SC3311A-QRSTA STBY 5V VCTRL INTERFACE C611...
  • Page 35 CN5204 STBY AUDIO12V :S-MICRO MUTE IIC CLK IIC DATA (AUDIO) R5213 R5214 0.47 STBY 5V R5225 :CHIP 1/4W D5205 1/10W :FPRD R5223 C5217 C5310 C5209 TO A BOARD R5201 D1NL20-TR2 :CHIP 8.2k 0.033 0.033 0.068 Q5205 R5211 1/10W CN319 1/10W R5239 R5222 :CHIP...
  • Page 36 — G BOARD — POWER, AUDIO • G BOARD SEMICONDUCTOR LOCATION DIODE IC603 B–1 D601 – IC604 B–1 D602 – IC605 C–3 D603 – IC606 B–2 D604 – IC607 C–3 D605 – IC608 C–3 D606 – IC610 E–1 D607 – IC611 D–1 D608...

  • Page 37: Semiconductors

    5-5. SEMICONDUCTORS TDA6103Q/N3,112 DTA114TK BA00AST LA6510 PQ12RF11 LA6500FA DTA124EKA-T146 DTC144EKA-T146 MARKING SIDE VIEW DTC314TKH04 DTC314TK-T-146 PDTC124EK-115 UN2115-QRS 9 pin ZIP 2SA1037AK-T146-R 2SA1037K-T-146-QR TDA7315D013TR 2SA1162G 2SB709A-QRS-TX PST600C-T LA7840L 2SC1623-L5L6 BA05T 2SC2412K-T-146-Q 2SC2412K-T-146-QR 2SD601A-Q TOP VIEW 2SD601A-QRS-TX 20 pin SOP TEA1504-N2 STK391-110 LM2405T BA10358F IRFI9630GS...
  • Page 38 IRLI540GLF33 DTZ-TT11-16B 2SD2144S-V D2S6M SB340L-5009 MA111 UF4007G23 RD5.6S-B CATHODE UDZ-TE-17-16B CATHODE UDZ-TE-17-5.6B UDZ-TE-17-6.2B ANODE ANODE ANODE 1SS226 2SA1175-HFE D4SB60L CATHODE 2SK1828 2SA1309A-QRSTA 2SC2785-HFE 2SC3311A-QRSTA D1NL20 2SC3311A-QTA EGP20G ERA22-08 ERB91-02 LETTER SIDE HSS82 2DK2101-01MR-F141 HZT33-02TE RGP02-17EL-6433 SPR-325MVW RGP02-17PKG23 RGP10DG23 EGP10D RL3Z-LF014-302 RH-1A UF400SPKG23 3DL41A...

  • Page 39: Exploded Views

    HMD-V200 SECTION 6 EXPLODED VIEWS NOTE: • Items with no part number and no • Items marked " * " are not stocked since ¡ The components identified by mark description are not stocked because they they are seldom required for routine are critical for safety.

  • Page 40: Picture Tube

    4-070-154-01 BOARD, BLIND * 8-933-376-00 J BOARD, COMPLETE 4-070-172-01 FOOT ¡ 8-738-550-61 ITC ASSY (17TKB-R1) 61-64 4-042-353-21 EMBLEM (NO. 7), SONY ¡ 8-738-546-05 PICTURE TUBE (17TKB) (SDS) ¡ 8-451-435-12 DEFLECTION YOKE (Y17TKJ-M) 4-308-870-00 CLIP, LEAD WIRE 1-452-032-00 MAGNET,DISC ; 10mmø...

  • Page 41: Packing Materials

    HMD-V200 6-3. PACKING MATERIALS ¡ The components identified by mark Les composants identifiés par une ¡ are critical for safety. marque sont critiques pour la Replace only with part number specified. sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. 105 106 107 REF.NO.

  • Page 42: Electrical Parts List

    HMD-V200 HMD-V200 ¡ The components identified by mark Les composants identifiés par une SECTION 7 ¡ marque sont critiques pour la sécurité. are critical for safety. Ne les remplacer que par une pièce Replace only with part number specified. ELECTRICAL PARTS LIST portant le numéro spécifié.
  • Page 43 HMD-V200 ¡ The components identified by mark Les composants identifiés par une ¡ are critical for safety. marque sont critiques pour la sécurité. Replace only with part number specified. Ne les remplacer que par une pièce portant le numéro spécifié. REF.NO.
  • Page 44 HMD-V200 ¡ Les composants identifiés par une The components identified by mark ¡ marque sont critiques pour la sécurité. are critical for safety. (a)(m)(g) Ne les remplacer que par une pièce Replace only with part number specified. portant le numéro spécifié. REF.NO.
  • Page 45 HMD-V200 ¡ The components identified by mark Les composants identifiés par une ¡ are critical for safety. marque sont critiques pour la sécurité. Replace only with part number specified. Ne les remplacer que par une pièce portant le numéro spécifié. REF.NO.
  • Page 46 HMD-V200 ¡ Les composants identifiés par une The components identified by mark ¡ marque sont critiques pour la sécurité. are critical for safety. Ne les remplacer que par une pièce Replace only with part number specified. portant le numéro spécifié. REF.NO.
  • Page 47 HMD-V200 ¡ The components identified by mark Les composants identifiés par une ¡ are critical for safety. marque sont critiques pour la sécurité. Replace only with part number specified. Ne les remplacer que par une pièce portant le numéro spécifié. REF.NO.
  • Page 48 HMD-V200 ¡ The components identified by mark Les composants identifiés par une ¡ marque sont critiques pour la sécurité. are critical for safety. (g)(c)(d) Ne les remplacer que par une pièce Replace only with part number specified. portant le numéro spécifié. REF.NO.
  • Page 49 HMD-V200 ¡ The components identified by mark Les composants identifiés par une ¡ are critical for safety. marque sont critiques pour la sécurité. Replace only with part number specified. Ne les remplacer que par une pièce portant le numéro spécifié. REF.NO.
  • Page 50 HMD-V200 ¡ Les composants identifiés par une The components identified by mark ¡ marque sont critiques pour la sécurité. are critical for safety. Ne les remplacer que par une pièce Replace only with part number specified. portant le numéro spécifié. REF.NO.
  • Page 51 HMD-V200 ¡ The components identified by mark Les composants identifiés par une ¡ are critical for safety. marque sont critiques pour la sécurité. Replace only with part number specified. Ne les remplacer que par une pièce portant le numéro spécifié. REF.NO.
  • Page 52 HMD-V200 ¡ The components identified by mark Les composants identifiés par une ¡ marque sont critiques pour la sécurité. are critical for safety. Ne les remplacer que par une pièce Replace only with part number specified. portant le numéro spécifié. REF.NO.
  • Page 53 The components identified by [ in this HMD-V200 ¡ manual have been carefully factory- The components identified by mark Les composants identifiés par une ¡ selected for each set in order to satisfy are critical for safety. marque sont critiques pour la sécurité. (d)(h) regulations regarding X-ray radiation.
  • Page 54 0.0047MF 10% 50V R1703 1-249-397-11 CARBON 1/4W F R1704 1-249-397-11 CARBON 1/4W F CN17021-695-915-11 TAB (CONTACT) CN1703*1-564-508-11PLUG, CONNECTOR 5P CN1704*1-564-507-11PLUG, CONNECTOR 4P Sony Corporation English Computer Display Company 99FL24179-1 9-978-646-01 Computer Display Div. Printed in Japan © 1999.6 7-13...

Table of Contents