Related Manuals for Miele DA 326-1 i
Summary of Contents for Miele DA 326-1 i
- Page 1 Operating and Installation Instructions Ventilation System DA 326-1 i DA 329-1 i To prevent accidents and machine damage, read these instructions before installation or use. M.-Nr. 05 864 020...
-
Page 3: Table Of Contents
Contents IMPORTANT SAFETY INSTRUCTIONS ....... . . 4 Guide to the hood ..........8 Functional description . -
Page 4: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS Read these Operating Instructions carefully before installing or using the Ventilation System. This appliance is designed to vent This appliance is intended for cooking smoke and odors only. residential use only. Use the Be certain your appliance is appliance only for its intended properly installed and grounded by purpose. - Page 5 Supervise its use by the conditions it may be possible for an elderly or infirm. installation in these applications. Please contact the nearest Miele dealer or the Be careful when preparing a Technical Service Department with flambé beneath the hood.
- Page 6 IMPORTANT SAFETY INSTRUCTIONS , WARNING - TO REDUCE , WARNING TO REDUCE THE RISK OF INJURY THE RISK OF A RANGE TOP TO PERSONS IN THE EVENT OF A GREASE FIRE: RANGE TOP GREASE FIRE, Never leave surface units OBSERVE THE FOLLOWING: unattended at high settings.
- Page 7 When installing the hood, follow the an active chimney, dryer vent, vent recommended minimum safety flue, or room ventilating ductwork. Seek distances between a Miele cooktop and professional advice before connecting the hood: an exhaust hood vent to an existing, –...
-
Page 8: Guide To The Hood
Guide to the hood... - Page 9 Guide to the hood a Vent connection i Light button b Active charcoal filter slot j On/Off button c Control panel k Power level buttons Four fan speed selection d Pull-out deflector plate e DFB Facia Panel (must be ordered separately) f Internal grease filter g Overhead cooktop light h External grease filter...
-
Page 10: Functional Description
Functional description The hood offers two modes of operation: Air extraction Recirculation mode The air is drawn in and cleaned by the Air is drawn through the grease filters grease filters and directed outside. and an active charcoal filter. The filtered air is then recirculated back into The hood comes equipped with a the kitchen through a vent at the top of... -
Page 11: Operation
Operation Turning the fan on Fan performance ^ Pull the deflector plate out about 2" The maximum air flow capacity is (5 cm). 625 cfm. Factors such as narrow duct diameter and bends will affect this The hood will operate at power level "II". value. -
Page 12: Turning The Light On
Operation Turning the light on Turning the light off ^ Press the light button again. The light for illuminating the cooktop can be turned on or off independently of the fan. ^ Push the deflector plate back in. ^ Pull the deflector plate out 1.5" (3 cm). -
Page 13: Cleaning And Care
Cleaning and care Stainless steel surfaces Before servicing or cleaning the Stainless steel surfaces can be cleaned hood, disconnect it from the power using a non-abrasive stainless steel supply by "tripping" the circuit cleaner. breaker or unplugging it. To help prevent resoiling, a conditioner for stainless steel can be applied. - Page 14 Cleaning and care ^ Cleaning the filters Removing the filters – by hand: with a nylon brush in a mild External filter solution of warm water and liquid ^ To remove the external filter pull the soap. deflector plate out slightly. –...
- Page 15 Cleaning and care Inserting the filters Internal filter ^ Make sure that the red plastic guides are at the front and facing up. ^ Fit the filter into the appliance so that it hooks into position at the back then push it up at the front and make sure it engages in position on the left and right hand sides.
-
Page 16: Inserting / Replacing The Active Charcoal Filters
Cleaning and care ^ Replace the filter every 6 months or Inserting / replacing the active when it is no longer absorbing charcoal filters cooking odors. Replacement active charcoal filters can be ordered from Technical Service. USA 1-800-999-1360 CDN 1-800-565-6435 Please quote part # 05 182 190. -
Page 17: Changing The Light Bulbs
Cleaning and care ^ Lower the cover to remove it. Changing the light bulbs ^ Replace the fluorescent bulb or the If the light does not work the bulb may need to be replaced or the starter could starter. be defective. ^ Secure the cover in position with the ^ Remove the external filter as fixing screws. -
Page 18: After Sales Service
After Sales Service In the event of a fault which you can not correct yourself please contact the Miele Technical Service Department 1-800-999-1360 [email protected] 1-800-565-6435 [email protected] When contacting the Technical Service Department, please quote the model and serial number of your appliance. -
Page 19: Installation Instructions
Installation Instructions... -
Page 20: Important Safety Instructions
When installing the hood, make sure [email protected] that the following minimum CDN 1-800-565-6435 distance (S) between the top of a Miele cooking surface and the [email protected] bottom of the hood is: - 18" (45 cm) above electric cooktops During the installation process, - 26"... -
Page 21: Electrical Data
Light Ensure that power to the appliance – DA 326-1 i ....1 x 15 W is "OFF" while installation or repair – DA 329-1 i ....1 x 16 W work is performed. -
Page 22: Appliance Dimensions
(See " (60 cm) cabinet. (See upper built-in depth of the upper cabinet). cabinet measures for DA 326-1 i). In this case, the lower portion of the hood 3) DFB light shield will overlap the bottom cabinets on (optional accessory) either side. - Page 23 Appliance dimensions Metric conversion table Millimeters Inches...
- Page 24 Appliance dimensions Installation in cabinetry Hood installed with a custom made light shield The depth of the installation depends on what type of light shield is used and the dimensions of surrounding cabinetry. Hood installed with a DFB light shield (optional accessory) To install the hood so that the light shield is flush with the adjacent cabinetry, the following dimensions...
- Page 25 Appliance dimensions Cabinet without rear panel If the cabinet does not have a back panel and there is no surrounding cabinetry a support bracket must be used to provide the unit with extra stability. A support bracket is available from Technical Service in the appropriate width.
-
Page 26: Installation
Installation Included parts... - Page 27 Installation a 2 hose clips for securing the vent ducting to the vent connection b 1 reducing collar 8 screws 3.5 x 16 mm for installing the for exhaust ducting of 5" (125 mm) runners and spacer blocks diameter c 1 non-return flap for fitting into the vent connection d 2 runners 6 self-tapping screws...
-
Page 28: Non-Return Flap
Installation 1. Non-return flap 2. Reducing collar Air extraction Air extraction The appliance is designed for 6" (150 mm) diameter ducting. If a 5" (125 mm) diameter is required: ^ Insert the non-return flap into the vent socket so the flaps open upward. (This is not necessary if the ducting system is already fitted with a non ^ Place the supplied reducing collar on... -
Page 29: Runners
Installation 3. Runners The measure "x" will depend on the type of lightshield used. The Miele DFB lightshield (optional accessory) sits flush with the cabinet front. ^ Cabinet width 60 cm: The runner’s adjustable range allows Install the runners on the left and... -
Page 30: Hang The Cabinet Door
Installation 4. Hang the cabinet door 6. Align the height of the appliance Before installing the appliance, hang and align the cabinet door. 5. Position the appliance in the cabinet ^ Screw 3 hexagon screws into the install bracket on each side. Do not tighten the middle one. -
Page 31: Installation Of A Lightshield
Installation 7. Installation of a lightshield DFB lightshield (optional accessory) Follow the installation instructions supplied with the DFB lightshield. Use the screws supplied with the lightshield. Custom made lightshield ^ Stick the three lengths of double sided tape to the custom lightshield and stick it to the deflector plate handle as shown above. -
Page 32: Align The Depth Of The Appliance
Installation 8. Align the depth of the 10. Install side spacers appliance " (60 cm) wide cabinet) ^ Push the hood into position. The side spacers cover the gaps between the sides of the appliance and 9. Secure the appliance the cabinet. -
Page 33: Spacer Strip For The Rear Of The Appliance
Installation 11. Spacer strip for the rear of the appliance ^ Insert the spacer strip to the underside of the appliance. ^ Turn the side cover caps upwards ^ Measure the gap "T" between the rear and press into position. of the appliance and the wall. -
Page 34: Light Cover
Installation 12. Light cover Reinserting the external filter: ^ Pull the deflector plate slightly out. ^ Remove the protective film from the the filter frame. ^ Tilt the front of the external filter slightly down and out. ^ Make sure that the red plastic guides are at the front and facing up. -
Page 35: 13 A. Air Extraction Mode
If the hood can not be installed for air extraction the appliance must be connected for recirculation mode. The following parts, available through your Miele Dealer or the Miele Technical Service Department are necessary for using the appliance in recirculation mode: –... -
Page 36: Electrical Connection
Installation Connection for recirculation mode ^ Install the Active Charcoal Filter (see "Cleaning and care"). 14. Electrical connection ^ The exhaust grill b must be fitted in the top of the unit. Refer to the notes in "Electrical If the front of the hood is installed at connection"... - Page 37 Installation Special installation instructions " (70 cm) width cabinet " (90 cm) width cabinet ^ The measure "x" will be calculated as described for a 23 " (60 cm) cabinet. ^ Screw the spacer block to the cabinet using 4.0 x 16 mm screws with the lower edge flush with the cabinet.
-
Page 38: Air Extraction
– The ducting should be as short and – If the exhaust is ducted through an straight as possible, and the number outside wall, a Miele Telescopic Wall of sharp bends should be minimized. Vent can be used. – For most efficient air extraction, the diameter of the ductwork should not be less than 6"... - Page 39 Air extraction – If the ductwork runs through rooms, ceilings, garages, etc. where temperature variations exist, it may need to be insulated to reduce condensation. In some cases, a condensate trap may also be required to collect and evaporate any condensate which may occur. When installing a condensate trap, ensure that it is positioned vertically and if possible directly above the...
-
Page 40: Caring For The Environment
Caring for the environment Disposal of packing material Disposal of an old appliance The cardboard box and packing Old appliances may contain materials materials protect the appliance during that can be recycled. Please contact shipping. They have been designed to your local recycling authority about the be biodegradable and recyclable. - Page 44 Alteration rights reserved / 1604 M.-Nr. 05 864 020 / 05 This paper was bleached without the use of chlorine.