JBL 700 User Manual
Axys uniamp power amplifier module
Hide thumbs
Also See for 700:
- Quick start manual (28 pages) ,
- Quick start manual (28 pages) ,
- Quick start manual (25 pages)
Table of Contents
Quick Links
Table of Contents
Related Manuals for JBL 700
Summary of Contents for JBL 700
-
Page 1: User Guide
User Guide AXYS UniAmp Power Amplifier Module ® Model 700... -
Page 2: Reference To Statements Of Conformity
User Guide - AXYS UniAmp Power Amplifier Module , Model 700 ® REFERENCE TO EC STATEMENT OF CONFORMITY No part of this manual including the software described This document confirms that products manufactured by in it may be reproduced, transmitted, transcribed, stored... -
Page 3: Table Of Contents
User Guide - AXYS UniAmp Power Amplifier Module , Model 700 ® TABLE OF CONTENTS Reference to Statements of Conformity ....2 User’s Notice and disclaimer ......2 1. -
Page 4: Important Safety Instructions
User Guide - AXYS UniAmp Power Amplifier Module , Model 700 ® 1.IMPORTANT SAFETY INSTRUCTIONS 12) Use only with the cart, stand, tripod, bracket or This symbol is intended to alert you to the pres- table specified by the manufacturer, or sold with the ence of uninsulated dangerous voltages within apparatus. -
Page 5: Introduction
This guide describes the operating procedures for the APPLICABLE MODELS AND VARIANTS AXYS UniAmp 700 power amplifier module. ® The UniAmp 700 is the power amplifier module fitted as The UniAmp 700 is a mains-powered power amplifier standard to the following AXYS powered loudspeakers: ®... -
Page 6: Connector And Wiring Details
3. CONNECTOR AND WIRING DETAILS CONNECTOR PANEL DIAGRAM 1 Audio input connector The full-load power consumption of the amplifier module is 700 VA under typical normal operating 2 Audio link connector conditions. When “daisy-chaining” AC mains between 3 RS-485 network input connector... -
Page 7: Audio Connections
UniAmp Power Amplifier Module , Model 700 ® The PowerCon connectors are plugged and un- The UniAmp 700’s audio input and output are twin ® plugged as shown in the diagram below. transformer-balanced, and are designed to operate at a nominal level of 0 dBV. Balanced system intercon-... -
Page 8: Network Connections
User Guide - AXYS UniAmp Power Amplifier Module , Model 700 ® 4. PRESETS The UniAmp 700’s DSP section includes 8 Presets; NETWORK CONNECTIONS memory locations in which sets of configuration pa- Two latching 5-pin XLR connectors are fitted for RS-485 rameters can be stored. -
Page 9: Reset
The fault condition numbers). should be identified and rectified before attempting Resetting the UniAmp 700 may also be carried out via to reset the breaker. Note that under extreme fault WinControl; see the WinControl Help files for more conditions, it may not be possible to reset the breaker. -
Page 10: Configuring With Wincontrol
UniAmp Power Amplifier Module , Model 700 ® 7. CONFIGURING WITH WINCONTROL Correct operation of a UniAmp 700 module may be The particular set of parameters which can be adjusted confirmed using WinControl software. via WinControl varies with loudspeaker model. Typically, it includes delay, gain and multi-band parametric EQ. -
Page 11: Appendix
User Guide - AXYS UniAmp Power Amplifier Module , Model 700 ® 8. APPENDIX NETWORK CABLES The type of cable necessary for correct operation of the RS-485 network is twin twisted pair with each pair individually shielded. Numerous cables of... - Page 12 JBL Professional 8500 Balboa Boulevard Northridge, CA 91329 U.S.A. © Copyright 2014 JBL Professional www.jblpro.com...