B model, which is different from the original LCD COLOR TV EWL20S5 and the EWL20S5 version A model. For EWL20S5 version B model, a suffix “B” is printed on the rating label on the back of the unit. Refer to the rating label illustration at right.
IMPORTANT SAFETY NOTICE Proper service and repair is important to the safe, reliable operation of all Funai Equipment. The service procedures recommended by Funai and described in this service manual are effective methods of performing service operations. Some of these service special tools should be used when and as recommended.
IMPORTANT SAFETY PRECAUTIONS Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.
Page 5
3. Design Alteration Warning - Do not alter or add 7. Product Safety Notice - Some electrical and to the mechanical or electrical design of this TV mechanical parts have special safety-related receiver. Design alterations and additions, characteristics which are often not evident from including, but not limited to circuit modifications visual inspection, nor can the protection they give and the addition of items such as auxiliary audio...
Page 6
Precautions during Servicing A. Parts identified by the # symbol are critical for L. When connecting or disconnecting the internal safety. connectors, first, disconnect the AC plug from the Replace only with part number specified. AC supply outlet. B. In addition to safety, other parts and assemblies M.
Page 7
Safety Check after Servicing Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified values in order to verify compliance with safety standards. 1.
STANDARD NOTES FOR SERVICING Circuit Board Indications How to Remove / Install Flat Pack-IC 1. The output pin of the 3 pin Regulator ICs is 1. Removal indicated as shown. With Hot-Air Flat Pack-IC Desoldering Machine: Top View Bottom View 1.
Page 9
3. The flat pack-IC on the CBA is affixed with glue, so With Soldering Iron: be careful not to break or damage the foil of each 1. Using desoldering braid, remove the solder from pin or the solder lands under the IC when all pins of the flat pack-IC.
Page 10
2. Installation With Iron Wire: 1. Using desoldering braid, remove the solder from 1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder the foil of each pin of the flat pack-IC on the CBA flux which is applied to all pins of the flat pack-IC, so you can install a replacement flat pack-IC more you can remove it easily.
Instructions for Handling Semi- conductors Electrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work. 1. Ground for Human Body Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged on the body.
CABINET DISASSEMBLY INSTRUCTIONS 1. Disassembly Flowchart Removal Step/ This flowchart indicates the disassembly steps for the Remove/*Unhook/ Loc. Part Fig. Unlock/Release/ cabinet parts, and the CBA in order to gain access to Note Unplug/Unclamp/ item(s) to be serviced. When reassembling, follow the Desolder steps in reverse order.
Page 13
[1] Rear Cabinet Fig. D1 [9] Front Cabinet [6] Function CBA [8] Speaker S-11 [3] Inverter CBA Speaker Holders [8] Speaker [4] Main S-11 Speaker Holders [5] LCD Module S-10 [7] IR Sensor CBA [2] Jack Holder Fig. D2 L2601DC...
Page 14
TV Cable Wiring Diagram Function CBA CLN104 To LCD Module Main CBA Inverter CBA CN1205 CN1206 CN1207 CN1201 CN301 CN404 CN304 To LCD CN302 Module CN303 CN310 CN801 CN1202 IR Sensor CBA CLN105 To Speaker To Speaker Fig. D3 L2601DC...
ELECTRICAL ADJUSTMENT INSTRUCTIONS General Note: “CBA” is abbreviation for How to set up the service mode: “Circuit Board Assembly.” Service mode: Note: Electrical adjustments are required after 1. Use the service remote control unit. replacing circuit components and certain mechanical parts. It is important to perform 2.
3. If Flicker Adjustment is not fit, the screen become Button Data the following. Item (on the service Value remote control) D2-BRT VCOM D2-CNT D2-CLR-R [MENU] → [5] D2-CLR-B D2-TNT D2-SHR D3-BRT D3-CNT D3-CLR-R FLASH (Go and Off) [MENU] → [6] D3-CLR-B 4.
The following adjustment normally are not 5. [RF/VIDEO1] attempted in the field. Only when replacing the When “x” value and “y” value are not within LCD Panel then adjust as a preparation. specification, adjust “DB (C/D1)” or “DR (C/D1)”. Refer to “1. Initial Setting.” 3.
HOW TO INITIALIZE THE LCD TELEVISION How to initialize the LCD television: 1. Turn the power on. (Use main power on the TV unit.) 2. To enter the service mode, press [SLEEP] button on the service remote control unit. - To cancel the service mode, press [POWER] button on the remote control.
SCHEMATIC DIAGRAMS / CBA'S AND TEST POINTS Standard Notes Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts that have these special safety characteristics are identified in this manual and its supplements;...
Page 26
LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES: 1. CAUTION: CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE_A,_V FUSE. ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE_A,_V. 2.
Page 31
Main 5/5 Schematic Diagram CAUTION ! NOTE: Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, If Main Fuse (F601) is blown , check to see that all components in the power supply The voltage for parts in hot circuit is measured using replace only with same type 4 A, 125V fuse.
Page 35
Main CBA Top View CAUTION ! Because a hot chassis ground is present in the power Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. supply circuit, an isolation transformer must be used. CAUTION ! : For continued protection against risk of fire, If Main Fuse (F601) is blown , check to see that all components in the power supply Also, in order to have the ability to increase the input...
Page 36
Main CBA Bottom View CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, If Main Fuse (F601) is blown , check to see that all components in the power supply replace only with same type 4 A, 125V fuse.
Page 37
Function CBA Top View IR Sensor CBA IR Sensor CBA Top View Bottom View Function CBA Bottom View BL2601F01031-2 BL2601F01031-1 8-13...
WAVEFORMS WF1 ~ WF12 = Waveforms to be observed at Waveform check points. (Shown in Schematic Diagram.) Input: NTSC Color Bar Signal (with 1kHz Audio Signal) CLKH STH1 S-VIDEO-C 1DIV: 1.0V 10 s 1DIV: 1.0V 10 s 1DIV: 200mV 20 s Pin 2 of CN1206 Pin 26 of CN1206 Pin 52 of IC1202...
EXPLODED VIEWS Cabinet Function CBA SP802 CLN802 CLN320 SP801 CLN801 CL1206 CL1207 CL1205 Inverter CBA IR Sensor CBA LCD1 See Electrical Parts List for parts with this mark. AC601 Main CBA 11-1 L2601CEX...
Page 42
Packing Some Ref. Numbers are not in sequence. Packing Tape Tape Packing Tape Packing Tape Packing Tape 11-2 L2601PEX...
MECHANICAL PARTS LIST PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
ELECTRICAL PARTS LIST PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No. # have special characteristics important to safety. C612 FILM CAP .(P) 0.01µF/50V J CMA1JJS00103 Before replacing any of these components, read C613 FILM CAP .(P) 0.056µF/50V J CMA1JJS00563 carefully the product safety notice in this service C631#...
Page 45
Ref. No. Description Part No. Ref. No. Description Part No. C819 CHIP CERAMIC CAP . B K 2200pF/50V CHD1JK30B222 C1256 CHIP CERAMIC CAP .(1608) B K 0.22µF/16V CHD1CK30B224 C820 CHIP CERAMIC CAP . B K 2200pF/50V CHD1JK30B222 C1257 CHIP CERAMIC CAP .(1608) B K 0.22µF/16V CHD1CK30B224 C853 ELECTROLYTIC CAP .
Page 53
Refer to the Rating Label on the back of the unit to make sure model types. This service manual is for the EWL20S5 C version model, and shows only the differences between the EWL20S5 C version model and EWL20S5 B version model.
Page 54
Different parts from the B version model (EWL20S5) Ref. No. Description Part No. MECHANICAL PARTS RATING LABEL L2621UB ---------- LCD1 LCD MODULE ASSEMBLY UE200XB 1FSA10155 CARTON L2601UB 1EM423468A OWNER S MANUAL L2601UB 1EMN21873A ELECTRICAL PARTS MMA CBA 1ESA13457 MAIN CBA...