SERVICE MANUAL COLOR MONITOR HP MX704 Series 41AP773-HP-E49 Ver:A01 Date: Feb-08-04 DATE DESCRIPTION APPROVALS Jan-16-04 NEW VERSION RELEASE Feb-08-04 Update BOM Jul-27-05 Update BOM...
Page 2
THESE DOCUMENTS ARE FOR REPAIR SERVICE INFORMATION ONLY. EVERY REASONABLE EFFORT HAS BEEN MADE TO ENSURE THE ACCURACY OF THIS MANUAL; WE CANNOT GUARANTEE THE ACCURACY OF THIS INFORMATION AFTER THE DATE OF PUBLICATION AND DISCLAIMS LIABILITY FOR CHANGES, ERRORS OR OMISSIONS.
2. PRECAUTIONS AND NOTICES SAFETY PRECAUTIONS Observe all caution and safety related notes located inside the display cabinet. Operation of the display with the cover removed, may cause a serious shock hazard from the display power supply. Work on the display should not be attempted by anyone who is not thoroughly familiar with precautions necessary when working on high voltage equipment.
HIGH VOLTAGE WARNING Operation of monitor outside of cabinet or with back removed may cause a serious shock hazard. Work on this model should only be performed by those who are thoroughly familiar with precautions necessary when working on high voltage equipment. Exercise care when servicing this chassis with power applied.
3. OPERATING INSTRUCTIONS This procedure gives you instructions for installing and using the Color display. Position the display on the desired operation and plug the power cord into a convenient AC outlet. Three- wire power cord must be shielded and is provided as a safety precaution as it connects the chassis and cabinet to the electrical conduit ground.
4. ADJUSTMENT 4-1 ADJUSTMENT CONDITIONS AND PRECAUTIONS Approximately 30 minutes should be allowed for warm up before proceeding. Adjustments should be undertaken only on those necessary elements since most of them have been carefully preset at the factory. 4-2 MAIN ADJUSTMENTS NO.
Page 10
(The OSD menu for factory preset FOR WT CPU) H-SIZE H-MOIRE REDUCE H-CENTER MOIRE DISABLE V-SIZE NO USE V-CENTER NO USE PINCUSHION NO USE PARALLELOGRAM V-LINEARITY PIN-BALANCE V-LINEARITY TRAPEZOID TOP CORNER ROTATION BOT CORNER NO USE NO USE CONTRAST MAX-HSIZE MODIFY BRIGHTNESS MAX-VSIZE MODIFY R-BIAS...
Page 11
USER OSD HORIZONTAL LOCATION 9300 COLOR TEMPERATURE ADJUST USER OSD VERTICAL LOCATION 6500 COLOR TEMPERATURE ADJUST FACTORY OSD VERTICAL LOCATION 5500 COLOR TEMPERATURE ADJUST V-MOIRE REDUCE Max H-Frequency select D. To switches the input signal to the other Timing Mode. Please follow step A ~ C to get the optimum picture.(H/V-size:312*234mm) E.
Page 12
5. Purity Adjustment A. Be sure that the display is not being exposed to any external magnetic fields. B. Ensure that the spacing between the Purity, Convergence, Magnet, (PCM), assembly and the CRT stem is 29mm. (See below diagram) C. Produce a complete, red pattern on the display. Adjust the purity magnet rings on the PCM assembly to obtain a complete field of the color red.
5. CIRCUIT DESCRIPTION 5-1 MICRO CONTROLLER CIRCUIT MICRO Controller The IC101 contains a 6502/8051 8-bit CPU core, 512 bytes of RAM, 16K bytes of ROM,14 channel 8 bit PWM D/A converters, 2 channel A/D converters for key detection, one 8 bit pre-loadable base timer, internal H-sync and V-sync signals processor providing mode detection, watch- dog timer preventing system from abnormal operation, and an I²C bus interface.
5-3 TRANSISTOR & DIODE CIRCUIT LOCATION CIRCUIT FUNCTION DESCRIPTION BD901 Bridge Rectifier for AC Source D910 Clamp Diode for snub CKT D918, D919 Rectifier for Output Voltage D922 Rectifier for Output Voltage D923 Rectifier for Output Voltage D925 Rectifier for B+ Supply D929 B+ Feed Back Rectifier from F.B.T Pulse IC901,Q901...
6.TROUBLE SHOOTING CHART 6-1 NO RASTER, CRT RELATIVE CIRCUIT PROBLEMS CHECK MAIN PCB POWER CHECK MAIN PCB POWER SUPPLY SUPPLY57.0V,13.6V,80V 53V, 14V, 78V CHECK POWER SAVING CIRCUIT, H-SYNC, V-SYNC SIGNAL Q909, Q910 CHECK THE HIGE VOLTAGE OF CHECK THE HIGE VOLTAGE CRT ABOUT 23~25KV REFER ITEM S.M.P.S.
Page 16
2.ABNORMAL VIDEO LEVEL ON SCREEN 3. ABNORMAL DDC (PLUG & PLAY)
Page 38
PARTS LIST OF IC802 ASS'Y LOCATION PARTS SPECIFICATION 2C6003 1 SCREW NUT 90C6026 12 HEAT SINK M1C1730 8128 SCREW M3x8 IC802 56C 551 11 LM2466TA PARTS LIST OF IC601 ASS'Y LOCATION PARTS SPECIFICATION 5C 71 1 TRANSISTOR HOUSING 32C3028504 MICA 90C 376 1 HEAT SINK M1C1730 12128...
Page 39
PARTS LIST OF AC ASS'Y LOCATION PARTS SPECIFICATION 15C5659503 REAR BRACKET B1C1140 6128 SCREW PARTS LIST OF SHIED ASS'Y LOCATION PARTS SPECIFICATION 85C6083 1 SHIELD 85C6084 1 SHIELD M1C1030 5128 SCREW PARTS LIST OF AC SOCKET ASS'Y LOCATION PARTS SPECIFICATION 87C 501 6 AC SOCKET CN901...
Page 40
PARTS LIST OF CRT ALTERNATION LOCATION PARTS SPECIFICATION 750A5X182AV CPT 17" RF 0.13 P1 CRT C450 65C 1K221 5T 220PF/1KV Y5P+-10% C480 65C 1K101 5T 100PF/1KV Y5P+-10% R490 61C 21025352T MFR 25KOHM +-1% 1/6W TP403 95C201M 5014D WIRE HARNESS PARTS LIST OF CRT ALTERNATION LOCATION PARTS SPECIFICATION...