SDM-P82 US Model SERVICE MANUAL Canadian Model SPECIFICATIONS LCD panel Panel type: a-Si TFT Active Matrix Dimensions (width/height/depth) Picture size: 18.1 inch Display (upright): Approx. 404 × 406 × 201 mm Input signal format RGB operating frequency* (16 × 16 × 8 inches) Horizontal: 28 –...
Page 2
AC Leakage. Check leakage as de- To Exposed Metal scribed right. Parts on Set 0.15 µF 1.5 kΩ Voltmeter (0.75 V) Earth Ground Fig. A. Using an AC voltmeter to check AC leakage. SDM-P82(UC) 2...
Page 3
REMPLACER QUE PAR UNE PIÈCE PORTANT LE NUMÉRO PARTS LIST ARE CRITICAL FOR SAFE OPERATION. REPLACE SPECIFIÉ. LES RÉGLAGES DE CIRCUIT DONT L’IMPORTANCE EST THESE COMPONENTS WITH SONY PARTS WHOSE PART CRITIQUE POUR LA SÉCURITÉ DU FONCTIONNEMENT SONT NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN IDENTIFIÉS DANS LE PRÉSENT MANUEL.
In this case, you can manually set these adjustments (page 12). If you manually set these adjustments, they are stored in memory as user modes and automatically recalled whenever the monitor receives the same input signals. SDM-P82(UC) 4...
4-1. Chassis ..............2-2. Usea of Service Mode .......... 4-2. Packing Materials ..........2-3. Functions of Service Mode ........2-4. White Balance Adjustment ........2-5. Action after Replacing 5. ELECTRICAL PARTS LIST ....... the LCD Panel and Board ........SDM-P82(UC) 5...
AGING MODE. The NO SYNC AGING flag is held until it is cleared. To clear the NO SYNC AGING flag, go into the service mode and then set the AGING MODE to OFF, or execute the all mode recall. SDM-P82(UC) 2-1...
EEPROM TEST RGB RESET EXIT CHIPS AGING MODE REGISTERS VALUE CONTROL REG 000~1FF EXIT EXIT The operation procedure is basically same as that of the ordinary user controls. The function of each menu is explained in next section. SDM-P82(UC) 2-2...
Do not change the above setting until the white balance adjustment is completed. and then set the AGINGN MODE to OFF, or execute the all mode recall. CONTROL REG. This can check the data of the internal registers. This operation is not required usually. SDM-P82(UC) 2-3...
Page 16
(3) Adjust the SUB-BRIGHTNESS: R, G, and B. Specifications are listed below. (5) Select COLOR TEMP → 6500K in the service mode menu, and set the data Brightness (cd/m listed below as initial data for adjustment. 0.283 ± 0.003 0.298 ± 0.003 14 ± 0.7 SUB-BRIGHTNESS SUB-CONTRAST SDM-P82(UC) 2-4...
(2) Check of picture and sound. After replacing the G board (1) Operation check of the MAIN POWER switch. (2) Check of picture and sound. After replacing the H board (1) Operation check of buttons and LED's in the front panel. SDM-P82(UC) 2-5...
! sont critiques pour la Source Transistor Drain sécurité. Ne les remplacer que par une pièce (FET) Gate portant le numéro spécifié. Emitter Transistor Collector Base – Discrete semiconductot Ver.1.6 (Chip semiconductors that are not actually used are included.) SDM-P82 (UC)
Page 21
One sheet of A board are circuit diagram is divided into eight sheets, each having the code A-a to A-g. For example, the destination ab1 on the code A-a sheet is connected to ab1 on the A-b sheet. a b 1 Ref. No. Circuit diagram division code SDM-P82(UC)
Page 22
One sheet of A board are circuit diagram is divided into eight sheets, each having the code A-a to A-g. For example, the destination ab1 on the code A-a sheet is connected to ab1 on the A-b sheet. a b 1 Ref. No. Circuit diagram division code SDM-P82(UC)
Page 23
One sheet of A board are circuit diagram is divided into eight sheets, each having the code A-a to A-g. For example, the destination ab1 on the code A-a sheet is connected to ab1 on the A-b sheet. a b 1 Ref. No. Circuit diagram division code SDM-P82(UC)
Page 24
One sheet of A board are circuit diagram is divided into eight sheets, each having the code A-a to A-g. For example, the destination ab1 on the code A-a sheet is connected to ab1 on the A-b sheet. a b 1 Ref. No. Circuit diagram division code SDM-P82(UC)
Page 25
One sheet of A board are circuit diagram is divided into eight sheets, each having the code A-a to A-g. For example, the destination ab1 on the code A-a sheet is connected to ab1 on the A-b sheet. a b 1 Ref. No. Circuit diagram division code SDM-P82(UC)
Page 26
One sheet of A board are circuit diagram is divided into eight sheets, each having the code A-a to A-g. For example, the destination ab1 on the code A-a sheet is connected to ab1 on the A-b sheet. a b 1 Ref. No. Circuit diagram division code SDM-P82(UC)
Page 27
One sheet of A board are circuit diagram is divided into eight sheets, each having the code A-a to A-g. For example, the destination ab1 on the code A-a sheet is connected to ab1 on the A-b sheet. a b 1 Ref. No. SDM-P82(UC) 3-10 Circuit diagram division code...
Page 28
[ MAIN CPU,SYSTEM IC,COLOR DEC,A/D CONV,3D COMB FILTER ] — A BOARD — SDM-P82(UC) 3-11...
Page 29
[ MAIN CPU,SYSTEM IC,COLOR DEC,A/D CONV,3D COMB FILTER ] — A BOARD — SDM-P82(E) 3-12...
The components identified ! marked are critical for safety. Replace only with the part number specified. Les composants identifiés par la marque sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. SDM-P82(UC) 4-1...
REF.NO. PART NO. DESCRIPTION REMARK 4-1. CHASSIS X-4040-765-1 BEZEL ASSY 3-704-176-51 EMBLEM (NO.6), SONY 1-761-645-11 H BOARD, MOUNT 1-804-967-11 PANEL, LCD (LM181E05) 1-761-646-11 I BOARD, MOUNT 1-761-615-11 G BOARD, MOUNT 1-761-644-11 A BOARD, MOUNT X-4040-766-1 STAND ASSY +RK 3X6 4-090-701-01 ARM (REAR)
Ne les remplacer que par une pièce portant service. Some delay should be anticipated le numéro spécifié. when ordering these items. RESISTORS When indicating parts by reference • All resistors are in ohms number, please include the board name. • F : nonflammable SDM-P82(UC) 5-1...