Related Manuals for Honeywell ULTRAKEY LITE HJC5000
Summary of Contents for Honeywell ULTRAKEY LITE HJC5000
- Page 1 UltraKey Lite Keyboard controller for VideoBloX and MAXPRO-Net Matrix Systems HJC5000 Installation and User Guide Document 800-07422 – Rev A – 08/10...
- Page 3 Installation and User Guide...
- Page 4 Revisions Issue Date 800-03854 rev A 02/2009 800-03854 rev B 03/2009 800-03854 rev C 04/2009 800-07422 rev A 08/2010 Revisions New document. Updated the MaxPRO map code. Corrected the controller login PIN code; corrected IP address p. 59; updated images for quality Revisions to Step 3: Configure Address, Baud Rate or IP for VideoBloX Mode;...
- Page 5 Explanation of Symbols WARNING! The exclamation point in a red octagon is a WARNING. Failure to take or avoid a specific action could result in physical harm to a person or irreparable damage to equipment. Caution The lightning flash with arrowhead symbol within an equilateral triangle alerts the user to the presence of uninsulated dangerous voltage within the enclosure of the product that may be of sufficient magnitude to constitute a risk of electric shock to the person...
- Page 6 Users of the product are responsible for checking and complying with all federal, state, and local laws and statutes concerning the monitoring and recording of video and audio signals. Honeywell shall not be held responsible for the use of this product in violation of current laws and statutes.
-
Page 7: Important Safety Instructions
Consider using a UPS source to ensure satisfactory performance. Using replacement parts or accessories other than the original manufacturers may invalidate the warranty. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Important Safety Instructions BEFORE OPERATING OR INSTALLING THE UNIT, READ AND FOLLOW ALL INSTRUCTIONS. - Page 8 In the event you have a problem with any Honeywell product, call Customer Service for assistance or to request a Return Merchandise Authorization (RMA) number. Be sure to have the model number, serial number, and the nature of the problem available for the technical service representative.
-
Page 9: Table Of Contents
Contents About this Document and the UltraKey Lite ......15 Document Overview ..........15 Finding More Information. - Page 11 Figures Figure 1-1 UltraKey Lite Port Connections ....... . 19 Figure 1-2 Terminal Box Front and Back Ports .
- Page 12 Figure 5-2 Change Password Page ........69 Figure 5-3 System Configuration LCD Menu Tree - All Modes .
- Page 13 Tables Table 1-1 UltraKey Lite Specifications........17 Table 1-2 Shipping Checklist .
-
Page 15: About This Document And The Ultrakey Lite
• UltraKey Lite Port Connections and The UltraKey Lite (HJC5000) is a replacement for the Honeywell HEGSBLX controller and is compatible with Honeywell VideoBloX and MAXPRO-Net Video Matrix Systems. The UltraKey Lite has these modes available depending on the installation: •... -
Page 16: Finding More Information
About this Document and the UltraKey Lite Finding More Information Refer to the online literature library to access other electronic documents in PDF format including data sheets, quick references, installation and user guides, specifications, software and product notices: http://www.honeywellvideo.com. Also see the back cover for international web sites and contact details. -
Page 17: Ultrakey Lite Specifications
UltraKey Lite Specifications Table 1-1 Parameter Power Requirements Connector Types Compliance Mechanical Environment Document 800-07422 Rev A 08/10 UltraKey Lite Controller Installation and User Guide UltraKey Lite Specifications Value 10.8 to 13.2 VDC @ 1 Ampere (A) or POE (48 VDC, Class 3) 1×Ethernet (10Base-T, 100Base-TX) RJ45 with LED 1×RS232/422/485 RJ45 with LED Type: STN, Positive Image... -
Page 18: Shipping Checklist
About this Document and the UltraKey Lite Shipping Checklist The following is included with your UltraKey Lite Controller shipment. Use of accessories is dependent on the type of installation. Ultrakey Lite can be connected to the matrix system either by serial port or Ethernet RJ45 connections. Table 1-2 Quantity Part... -
Page 19: Ultrakey Lite Port Connections And Descriptions
UltraKey Lite Port Connections and Descriptions Figure 1-1 DC Power Port Supports 12V (±10%) DC/1 A power input. Use the power adapter included with the shipment and insert one of the four adapters based on your local power requirements. Ethernet Port Note •... -
Page 20: Figure 1-2 Terminal Box Front And Back Ports
About this Document and the UltraKey Lite RS232, RS422/485 Serial Port Note An isolated surge protection is suggested when using RS485/RS422 and when cabling between buildings. Note Note Terminal Box Use the terminal box RJ45 port and 8-pin terminal plug as required for compatibility and connectivity options. -
Page 21: Using The Ultrakey Lite Controller
Using the UltraKey Lite Controller You may need to learn how to use the UltraKey Lite both before and after you begin configuring. In this section: • Logging Onto the • Using the UltraKey Lite to Navigate the LCD • VideoBloX Key •... -
Page 22: Using The Ultrakey Lite To Navigate The Lcd Menus
Using the UltraKey Lite Controller Using the UltraKey Lite to Navigate the LCD Menus There are a variety of ways to navigate both the LCD menus during configuration and set up as well as during normal operation with your matrix system. keys and other elements of the UltraKey Lite controller. -
Page 23: Figure 2-2 The Ultrakey Navigation Controls
Figure 2-2 Touch Pad and Ring Touch pad - Use like a laptop mouse pad LCD Keys Joystick Table 2-1 Task To confirm a change or enter the current menu To cancel an operation or return to the previous level of the menu To view or switch between the menu items of the same level Document 800-07422 Rev A... -
Page 24: Videoblox Key Functions
ID column. The keyboard supports dynamic key configuration. The key functions listed in Table 2-2 are all default functions. Contact Honeywell Technical Support or refer to the applicable VideoBloX manual. VideoBloX Key Functions... - Page 25 Table 2-2 Key Description Function in Camera Mode Pause Play Rev Selects previous camera Review Puts keyboard in Device mode Record Store a preset (preshot) Search Puts keyboard in Device mode Pause Play Fwd Selects next camera Tour Tour 1 Runs SEQ 250 on CPU Tour 2 Runs SEQ 251 on CPU Tour 3 Runs SEQ 252 on CPU Tour 4 Runs SEQ 253 on CPU...
- Page 26 Using the UltraKey Lite Controller Table 2-2 Key Description Function in Camera Mode Mon A Depends on controller address. EG, Add 1 SEQ201 run, Add 2, SEQ202 run, and so on. Login Login/Logout of CPU F1: Define in CFG software F2: Define in CFG software F3: Define in CFG software F4: Define in CFG software...
-
Page 27: Maxpro Key Functions
MAXPRO Key Functions Note Table 2-3 Key Description Alarm Iris + Iris - Recycle (Undo) Pause Play Rev Review Record Search Pause Play Fwd Tour View MUX Screen 16-1 Number 1 16-2 Number 2 16-3 Number 3 16-4 Number 4 16-5 Number 5 16-6... - Page 28 Using the UltraKey Lite Controller Table 2-3 Key Description Clear Monitor Camera PTZ Call Touch wheel right Touch wheel left Touch ring Up Touch ring Down Touch ring Left Touch ring Right Joystick Left Joystick Right Joystick Up Joystick Down Twist Zoom right Twist Zoom left Mon B...
- Page 29 Table 2-3 Key Description 21+30 F10+F5 21+30 F10+F6 21+30 F10+F7 21+30 F10+F8 21+30 F10+F9 24/26 Focus + 24/26 Focus - Document 800-07422 Rev A 08/10 UltraKey Lite Controller Installation and User Guide MAXPRO Key Functions (cont’d) Key Code Default MAX Function Pause None Scroll Down...
- Page 30 Using the UltraKey Lite Controller...
-
Page 31: Installing Ultrakey Lite With Videoblox
Installing UltraKey Lite with VideoBloX In this section: • Navigating the LCD Configuration • Installing and Configuring a Serial • Installing and Configuring an Ethernet • (Optional) Configuring UltraKey Lite Using the Web Note This section explains how to connect the UltraKey Lite controller to VideoBloX and how to enter the basic configuration settings specific to VideoBloX. -
Page 32: Installing And Configuring A Serial Connection
Installing UltraKey Lite with VideoBloX Figure 3-1 Left Down arrow arrow arrow Figure 3-2 Connection Serial Port Installing and Configuring a Serial Connection Step 1: Connect to the UltraKey Lite Using the Serial Port Note LCD and LCD Navigation Keys Right arrow VideoBloX LCD Configuration Menu Tree... -
Page 33: Figure 3-3 Ac Power Adapter With Cee 7/16 Europlug
Table 3-1 Serial Port COM1 Note Select the applicable adapter plug and insert it into the AC adapter. Push to click it into place. See Plug the AC adapter into the controller power port and the adapter into a power source. -
Page 34: Figure 3-4 Rj45 To Db9 Male Adapter For Videoblox And Videoblox Lite Cpus
Installing UltraKey Lite with VideoBloX Figure 3-4 VideoBloX Figure 3-5 VideoBloX Figure 3-6 VB master: 1--RS422_TX – 2--RS422_TX + 3--RS422_RX + 4--RS422_RX – 5--GND RJ45 define: 1--RS485_2+/RS422_2_TX+/ RS422_1_RX+ 2--RS485_2-/RS422_2_TX-/ RS422_1_RX- 3—NC 4--RS232RX 5--RS232GND 6--RS232TX 7--RS485_1-/RS422_1_TX- 8--RS485_1+/RS422_1_TX+ *RS485_2/RS422_2_TX and RS232 use same UART_AC Step 2: Configure the Controller for VideoBloX Mode Note RJ45 to DB9 Male Adapter for VideoBloX and VideoBloX Lite CPUs... - Page 35 If not already done, install and connect the controller to a power source. From the home screen, press Set menu. Enter the PIN password 3434. The System Set: Mode screen displays. Press the LCD right arrow key to enter the Mode Selection menu. Scroll to and select VideoBloX.
-
Page 36: Installing And Configuring An Ethernet Connection
Installing UltraKey Lite with VideoBloX Note 16. Use the numeric keypad to enter an IP address as required, then press Ent. Step 4: Configure VideoBloX Mode Default Settings While Powering Up While powering up, when the Time Left 3 menu displays, press Alt > Camera to set the VideoBlox mode. -
Page 37: Figure 3-7 Ethernet Port Connections To Videoblox
Table 3-2 Port RJ45 Ethernet Select the applicable adapter plug and insert it into the AC adapter. Push to click it into place. See Plug the AC adapter into the controller power port and the adapter into a power source. Plug an RJ45 network cable from the network to the controller Ethernet port. - Page 38 Installing UltraKey Lite with VideoBloX Step 3: Set and Configure for an Ethernet Connection Press Alt > Clr. If prompted, enter the password 3434 to enter the System Set top menu. Press the LCD down arrow to scroll to the System Set: Config menu.
- Page 39 Press the LCD up/down arrow keys to scroll through the options (serial port, network, language, back light, slider update, cascade linkage, hardware test, about). Scroll to the Configuration: Network menu, then press Ent. There are three sub-menus in this menu (Show Net Infor, DHCP, and Manual Settings).
- Page 40 Installing UltraKey Lite with VideoBloX When you are at the Network: Manual Setting menu, press Ent, then press the LCD up/down arrow keys to set the UltraKeyLite network parameters (IP address, gateway, netmask and DNS). Press the LCD up/down arrow keys to scroll through the menu options to select IP Address, then press Ent to select.
-
Page 41: (Optional) Configuring Ultrakey Lite Using The Web Browser
Step 5: Setting the Keyboard Address While Powering Up While powering up, when the Time Left 3 menu displays, press certain keys (see to set the keyboard address. Table 3-3 Alt > 1 Alt > 2 Alt > 3 Alt > 4 Alt >... -
Page 42: Figure 3-8 Ultrakey Lite Login Page
Installing UltraKey Lite with VideoBloX Figure 3-8 Step 1: Configure UltraKey Lite to VideoBloX Mode Log into the web browser. From the top menu, click the Configuration tab. See From the side menu, click the System Configurations tab. From the System Mode drop down list, select VideoBlox. From the System Language drop down list, select English or French. -
Page 43: Figure 3-10 Videoblox Configuration Tab
Note Under VB Device Network Setting, enter the IP address and Port Number of the VideoBloX system. Click Apply to save the configuration, Cancel to exit without saving, or Default to restore all factory default values. Go to either Step 3A or 3B to configure the system for Serial or Ethernet connections respectively. -
Page 44: Figure 3-11 Serial Port Configuration Tab
Installing UltraKey Lite with VideoBloX Under Serial Port1 Settings, select the following from each drop-down list as required: • Baud Rate: 1200, 9600, 19200 or 57600 bps. The default for VideoBloX is 19200. • Parity: none • Stop Bits: 1 bit •... -
Page 45: Figure 3-13 Dynkey Configuration Tab
Step 4: Configuring the Dynamic Keys You can configure the hard keys on the web server. From the side menu, click DynKey Configuration. Figure 3-13 In the drop-down menu, select the key you want to configure. In the right column, select the function you want to add to the hard key, then click Add. - Page 46 Installing UltraKey Lite with VideoBloX...
-
Page 47: Installing Ultrakey Lite With Maxpro-Net
Installing UltraKey Lite with MAXPRO-Net In this section: • Navigating the LCD Configuration • Installing and Configuring a Serial • Installing and Configuring an Ethernet • (Optional) Configuring UltraKey Lite Using the Web Note This section explains how to connect the UltraKey Lite controller to MAXPRO-Net and how to enter the basic configuration settings specific to MAXPRO-Net. -
Page 48: Figure 4-1 Lcd And Navigation Keys
Installing UltraKey Lite with MAXPRO-Net Figure 4-1 Left Down arrow arrow arrow Figure 4-2 Connection By Serial Port By Ethernet RS232 directly RS422 indirectly Keyboard ID Baud Rate 1 to 32 9600 / 19200 bps From the MAXPRO settings menu, you set the following based on either a Serial or Ethernet connection: •... -
Page 49: Installing And Configuring A Serial Connection
Installing and Configuring a Serial Connection Step 1: Connect to the UltraKey Lite Serial Port Note Note Table 4-1 Serial Port COM1 COM2 Document 800-07422 Rev A 08/10 UltraKey Lite Controller Installation and User Guide For a list of accessories see Shipping Checklist connections see UltraKey Lite Port Connections and Descriptions... -
Page 50: Figure 4-3 Rs232 Serial Port Connection
Installing UltraKey Lite with MAXPRO-Net Figure 4-3 RJ45 define: 1--RS485_2+/RS422_2_TX+/ RS422_1_RX+ 2--RS485_2-/RS422_2_TX-/ RS422_1_RX- 3—NC 4--RS232RX 5--RS232GND 6--RS232TX 7--RS485_1-/RS422_1_TX- 8--RS485_1+/RS422_1_TX+ *RS485_2/RS422_2_TX and RS232 use same UART_AC Figure 4-4 MEGAPIT 1--RS422_TX+ 2--RS422_TX- 3--NC 4--RS232TX 5--RS232GND 6--RS232RX 7--RS422_RX- 8--RS422_RX+ RJ45 define: 1--RS485_2+/RS422_2_TX+/ RS422_1_RX+ 2--RS485_2-/RS422_2_TX-/ RS422_1_RX- 3—NC... -
Page 51: Figure 4-5 Rs232 Serial Port Connection And Mx18
Figure 4-5 RJ45 define: 1--RS485_2+/RS422_2_TX+/ RS422_1_RX+ 2--RS485_2-/RS422_2_TX-/ RS422_1_RX- 3—NC 4--RS232RX 5--RS232GND 6--RS232TX 7--RS485_1-/RS422_1_TX- 8--RS485_1+/RS422_1_TX+ *RS485_2/RS422_2_TX and RS232 use same UART_AC Controller 1 RS232 Connections with an RJ45 to DB9 Female Adapter Select the applicable adapter plug and insert it into the AC adapter. Push to click it into place. -
Page 52: Figure 4-8 Rs422 To Rs232 Converter Using The Terminal Box (Rs422)
Installing UltraKey Lite with MAXPRO-Net RS422 Connections Using a Converter and the Terminal Box Select the applicable adapter plug and insert it into the AC adapter. Push to click it into place. See Connect an RJ45 network cable from the RJ45 port on the terminal box to the controller serial port. -
Page 53: Figure 4-9 Rs232 Serial Port Connection And Terminal Box Rs422
Figure 4-9 1--RS485_1+/RS422_1_TX+ 2--RS485_1-/RS422_1_TX- 3--RS485_2+/RS422_2_TX+ /RS422_1_RX+ 4--RS485_2-/RS422_2_TX- /RS422_1_RX- 5--RS232RX 6--RS232TX 7--RS232GND 8--RS232GND *RS485_2/RS422_2_TX and RS232 use same UART_AC Figure 4-10 1--RS485_1+/RS422_1_TX+ 2--RS485_1-/RS422_1_TX- 3--RS485_2+/RS422_2_TX+ /RS422_1_RX+ 4--RS485_2-/RS422_2_TX- /RS422_1_RX- 5--GND 6--GND 7--RS232TX 8--RS232RX *RS485_2/RS422_2_TX and RS232 use same UART_AC Network Controller 1 Document 800-07422 Rev A 08/10 UltraKey Lite Controller Installation and User Guide RS232 Serial Port Connection and Terminal Box RS422... - Page 54 Installing UltraKey Lite with MAXPRO-Net Step 2: Configure the Controller for MAXPRO Mode Note If not already done, install and connect the controller to a power source. The UltraKey Lite LCD displays. From the home screen, press Alt > Clr to enter the System Configuration: System Set menu.
- Page 55 Note Use the LCD up/down arrow keys to select RS232 or RS422, then press Ent. Use the LCD up/down arrow keys to scroll to an address between 1 and 99 to assign to the controller, then press Ent to save. Press the down LCD arrow key to scroll to Baud Rate.
-
Page 56: Installing And Configuring An Ethernet Connection
Installing UltraKey Lite with MAXPRO-Net Baud Rate: 19.2 KB Data Bit: 7 Parity: Even Stop Bit: 1 Installing and Configuring an Ethernet Connection Step 1: Connect to the UltraKey Lite Ethernet Port Table 4-3 Port RJ45 Ethernet Plug an RJ45 network cable from the network to the controller Ethernet port. Up to 99 controllers can be connected to the network. - Page 57 Step 2: Configure the Controller for MAXPRO Mode Note Step 3: Set and Configure for an Ethernet Connection From the MAXPRO connection submenu, select Ethernet. Note Press the LCD center key. The Maxpro Settings: Keyboard ID menu opens. Press Ent. Use the LCD up/down arrow keys to scroll to an address between 1 and 99 to assign to the controller.
- Page 58 Installing UltraKey Lite with MAXPRO-Net Step 4: Configure the Controller for an Ethernet Connection Press Alt > Clr to exit from the VideoBloX configuration menu. Press Alt > Clr a second time to enter the System Set top menu. Press the LCD down arrow key to scroll to the System Set: Config menu.
- Page 59 When the nework configures successfully, the user can enter the Show Net Infor menu to see the IP Address, IP Address, DNS, Gateway and Netmask. Manually Configuring the Network Manually configuring the network using the Manual Setting menu: Press the LCD down arrow key to scroll to the Network: Manual Setting menu When you are at the Network: Manual Setting menu, press Ent, then press the LCD up/down arrow keys to set the UltraKeyLite network parameters (IP address, gateway, netmask and DNS).
-
Page 60: (Optional) Configuring Ultrakey Lite Using The Web Browser
Installing UltraKey Lite with MAXPRO-Net Step 5: Setting the Keyboard Address While Powering Up While powering up, when the Time Left 3 menu displays, press certain keys (see to set the keyboard address. Table 4-4 Alt > 1 Alt > 2 Alt >... -
Page 61: Figure 4-12 Ultrakey Lite Login Page
Figure 4-12 Step 1: Configure UltraKey Lite to MAXPRO Mode Log into the web browser. From the top menu, click the Configuration tab. See From the side menu, click the System Configurations tab. From the System Mode drop-down list, select MAXPRO. From the System Language drop-down list, select English or French. -
Page 62: Figure 4-14 Maxpro Configuration Tab
Installing UltraKey Lite with MAXPRO-Net Enter the IP address and Port Number of the MAXPRO-Net server under MAXPRO Device Network Setting. Under Serial Port Setting, select a Baud Rate from the drop-down list. Options are 9600 or 19200 bps. Select a Connect Mode from the drop-down list. Options are 232 or 422. From the Joystick speed drop-down list, select Normal or High. -
Page 63: Figure 4-15 Serial Port Configuration Tab
Click Apply to save the configuration, Cancel to exit without saving or Default to restore all factory default values. Figure 4-15 Step 3B: Configure the Controller for an Ethernet Connection From the side menu, click IP Configuration. In each of the fields, enter IP address, subnet mask, gateway and DNS values. Click Apply to save the configuration, Cancel to exit without saving or Default to restore all factory default values. -
Page 64: Figure 4-17 Dynkey Configuration Tab
Installing UltraKey Lite with MAXPRO-Net Figure 4-17 In the drop-down menu, select the key you want to configure. In the right column, select the function you want to add to the hard key, then click Add. That selected function appears in the center column. Repeat Click Apply to save. -
Page 65: System Administration And Troubleshooting
System Administration and Troubleshooting In this section: • System Administration Using the Controller • System Administration Using the Web System Administration Using the Controller LCD To navigate all configuration LCD menus, see Logging in and Navigating to the System Set: Config Menu If not already done, install and connect the controller to a power source. - Page 66 System Administration and Troubleshooting Adjusting the Back Light Log into the controller. From the System Set: Config menu, press the LCD up/down arrow keys to scroll to Back Light. Press Ent. Use the LCD up and down arrow keys or the rotate the touch pad to adjust the back light intensity.
-
Page 67: Table 5-1 Hjc5000 Ultrakey Lite Controller Default Settings
Testing the Hardware Log into the controller. From the System Set: Config menu, press the LCD up/down arrow keys to scroll to Hardware Test. Press Ent. Press the LCD up/down arrow keys and press Ent to select one or all of the following test options: •... -
Page 68: System Administration Using The Web Browser
System Administration and Troubleshooting Table 5-1 Settings VideoBlox Mode Address Baud Rate Control Mode IP Address Default Back Light System Administration Using the Web Browser Logging into the Web Browser If not already done, navigate to, or copy and paste, the applicable IP address into your web browser: •... -
Page 69: Figure 5-1 Software Upgrade Warning Message
When the process is complete, the message Upgrade success displays and the system reboots. WARNING! Figure 5-1 Rebooting UltraKey Lite Log into the web browser. From the top menu, click the System Reboot tab. The Reboot System window opens. Click Reboot to continue or click another tab or Logout to exit without rebooting. Changing the UltraKey Lite Web Browser Password Log into the web browser. - Page 70 System Administration and Troubleshooting Figure 5-3 System Set: Configuration Configuration System Configuration LCD Menu Tree - All Modes Maxpro Settings Address Baud Rate VB Settings Control Mode IP Address Restore Defaults About Serial Port Hardware Test Slider Joystick Slider Update Adjust Bg Light Back Light Up/Down Slide...
- Page 72 +971.04.881.5506 © 2010 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell. The information in this publication is believed to be accurate in all respects. However, Honeywell cannot assume responsibility for any consequences resulting from the use thereof.