Sony KDL-26S3000 Service Manual
  1. Manuals
  2. Brands
  3. Sony Manuals
  4. LCD TV
  5. KDL-26S3000 - 26" LCD TV
  6. Service manual

Sony KDL-26S3000 Service Manual

Lcd digital color television
Hide thumbs Also See for KDL-26S3000:
Table of Contents

Quick Links

See also: Training Manual , Instruction Manual
HISTORY INFORMATION FOR THE FOLLOWING MANUAL:

SERVICE MANUAL

MODEL NAME
KDL-26S3000
KDL-32S3000
KDL-40S3000
KDL-46S3000
ORIGINAL MANUAL ISSUE DATE: 4/2007
: UPDATED ITEM
REVISION DATE
4/2007
5/2007
7/2007
10/2007
9-883-745-04
REMOTE COMMANDER
RM-YD018
RM-YD018
RM-YD018
RM-YD018
SUBJECT
No revisions or updates are applicable at this time.
Re-release entire manual.
Added correct PN for KDL-32S3000 ETC-Inverter MT Board. Replaced page 138.
Added PNs for new Colored Bezel models. Replaced page 138.
Added PN for Remote Battery Cover. Replaced page 174.
WAX3
DESTINATION
US/CANADA
US/CANADA
US/CANADA
US/CANADA
LCD DIGITAL COLOR TELEVISION
CHASSIS
Table of Contents
loading

Related Manuals for Sony KDL-26S3000

Summary of Contents for Sony KDL-26S3000

  • Page 1: Service Manual

    HISTORY INFORMATION FOR THE FOLLOWING MANUAL: WAX3 SERVICE MANUAL CHASSIS MODEL NAME REMOTE COMMANDER DESTINATION KDL-26S3000 RM-YD018 US/CANADA KDL-32S3000 RM-YD018 US/CANADA KDL-40S3000 RM-YD018 US/CANADA KDL-46S3000 RM-YD018 US/CANADA ORIGINAL MANUAL ISSUE DATE: 4/2007 : UPDATED ITEM REVISION DATE SUBJECT 4/2007 No revisions or updates are applicable at this time.
  • Page 2 Self Diagnosis Supported model WAX3 SERVICE MANUAL CHASSIS MODEL NAME REMOTE COMMANDER DESTINATION KDL-26S3000 RM-YD018 US/CANADA KDL-32S3000 RM-YD018 US/CANADA KDL-40S3000 RM-YD018 US/CANADA KDL-46S3000 RM-YD018 US/CANADA KDL-46S3000 RM-YD018 LCD DIGITAL COLOR TELEVISION 9-883-745-04...

  • Page 3: Table Of Contents

    (KDL-40S3000/46S3000 Only) ........ 16 D2 Board Schematic Diagram (KDL-46S3000 Only) ..122 1-10. D2 Board Removal (KDL-46S3000 Only) ......17 G1D Board Schematic Diagram (KDL-26S3000 Only) ..124 1-10-1. Replacing the Inverter Connector Assembly G1H Board Schematic Diagram (Power Supply) (KDL-46S3000 Only) ..........

  • Page 4: Specifi Cations

    Trademark Information “BRAVIA” and , S-Force, BRAVIA Theatre Sync, and DMe trademarks or registered marks of Sony Corporation. Blu-ray Disc is a trademark. “XMB”, “XrossMediaBar” and “PS3” are trademarks of Sony Corporation and/or Sony Computer Entertainment Inc. This TV incorporates High-Definition Multimedia Interface (HDMI™) technology.
  • Page 5 SU-WL100 (KDL-26S3000 Only) Display Resolution (horizontal x vertical): SU-WL500 (KDL-32S3000/40S3000/46S3000 Only) 1,366 dots x 768 lines TV Stand RHT-G800 (All except KDL-26S3000) Screen Size (measured diagonally) 26 inches (KDL-26S3000 Only) 31.5 inches (KDL-32S3000 Only) 40 inches (KDL-40S3000 Only) 46 inches (KDL-46S3000 Only)

  • Page 6: Warnings And Cautions

    Les composants identifi es par une trame et par une marque ! sur les schemas de principe, les vues explosees et les listes de pieces sont d’une importance critique pour la securite du fonctionnement. Ne les remplacer que par des composants Sony dont le numero de piece est indique dans le present manuel ou dans des supplements publies par Sony.

  • Page 7: Safety-Related Component Warning

    KDL-26S3000/32S3000/40S3000/46S3000 SAFETY-RELATED COMPONENT WARNING There are critical components used in LCD color TVs that are important for safety. These components are identifi ed with shading and mark on the schematic diagrams and the electrical parts list. It is essential that these critical parts be replaced only with the part number specifi...
  • Page 8 Due to the higher melting point of Lead Free Solder the soldering iron tip temperature needs to be set to 370 degrees centigrade. This requires soldering equipment capable of accurate temperature control coupled with a good heat recovery characteristics. For more information on the use of Lead Free Solder, please refer to http://www.sony-training.com KDL-26S3000/32S3000/40S3000/46S3000...

  • Page 9: Safety Check-Out

    KDL-26S3000/32S3000/40S3000/46S3000 SAFETY CHECK-OUT The AC leakage from any exposed metal part to earth ground and After correcting the original service problem, perform the following from all exposed metal parts to any exposed metal part having a safety checks before releasing the set to the customer: return to chassis, must not exceed 0.5 mA (500 microamperes).

  • Page 10: Self-Diagnostic Function

    KDL-26S3000/32S3000/40S3000/46S3000 Self Diagnosis SELF-DIAGNOSTIC FUNCTION Supported model The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY LED indicator will automatically begin to fl ash. The number of times the LED fl ashes translates to a probable source of the problem. A defi nition of the STANDBY LED fl ash indicators is listed in the instruction manual for the user’s knowledge and reference.
  • Page 11 KDL-26S3000/32S3000/40S3000/46S3000 Viewing the Self Check Diagnostic List 1. TV must be in standby mode. (Power off). 2. Press the following buttons on the Remote Commander within a second of each other: Channel 5 Volume - TV POWER . DISPLAY The Self Check list displays.

  • Page 12: Section 1: Disassembly

    Remove 3 screws from Terminals, +BVTP 3X12 TYPE2 IT-3 Remove 2 screws (KDL-26/32S3000), 4 screws (KDL-40/46S3000) from Rear Cover arm positions, +PSW M5X16 Remove 13 screws (KDL-26S3000), 14 screws (KDL-32S3000), 15 screws (KDL-40/46S3000), from Rear Cover, +BVTP2 4X16 Rear Cover 1-2.

  • Page 13: Stand Assembly And Vesa Arm Assembly Removal (Kdl-26S3000/32S3000 Only)

    KDL-26S3000/32S3000/40S3000/46S3000 1-3. STAND ASSEMBLY AND VESA ARM ASSEMBLY REMOVAL (KDL-26S3000/32S3000 ONLY) Remove 2 screws from bottom of Arms, +PSW M5X16 Remove 3 screws from bottom bracket and Stand, +PSW M5X16 VESA Arm Assembly Stand Assembly Under Cover Bottom Bracket 1-4. STAND ASSEMBLY AND VESA ARM ASSEMBLY REMOVAL...

  • Page 14: U1 Board, Dtt Shield, And Jack Holder Removal

    KDL-26S3000/32S3000/40S3000/46S3000 1-5. U1 BOARD, DTT SHIELD, AND JACK HOLDER REMOVAL Disconnect one connector Remove one screw, +BVTP 3X12 TYPE2 IT-3 Release hooks and remove U1 Board. Remove Jack holder from Bezel. Release hooks to remove DTT Shield from BU1 bottom shield.

  • Page 15: G1D/G1H Board (Power Unit) And G1 Bracket Removal (Kdl-26S3000/32S3000 Only)

    KDL-26S3000/32S3000/40S3000/46S3000 1-7. G1D/G1H BOARD (POWER UNIT) AND G1 BRACKET REMOVAL (KDL-26S3000/32S3000 ONLY) Remove 4 screws, +PSW 3SG Disconnect 3 connectors Power Unit G1 Bracket 1-8. SPEAKER, H3 BOARD, AND H4 BOARD REMOVAL Slide out Speaker and Baffl e from Bezel...

  • Page 16: G3 Board (Power Unit) And D1 Board Removal (Kdl-40S3000/46S3000 Only)

    KDL-26S3000/32S3000/40S3000/46S3000 1-9. G3 BOARD (POWER UNIT) AND D1 BOARD REMOVAL (KDL-40S3000/46S3000 ONLY) Disconnect 6 connectors Remove 4 screws, +PSW 3SG Disconnect 4 connectors D1 Board Remove 4 screws, +PSW 3SG G3 Board G3 Bracket 1-9-1. REPLACING THE INVERTER CONNECTOR ASSEMBLY (KDL-40S3000/46S3000 ONLY) Use the following procedure to confirm that the Inverter connector is securely attached to the board.

  • Page 17: D2 Board Removal (Kdl-46S3000 Only)

    KDL-26S3000/32S3000/40S3000/46S3000 1-10. D2 BOARD REMOVAL (KDL-46S3000 ONLY) Disconnect 3 connectors Remove 4 screws, +PSW 3SG D2 Board D2 Bracket 1-10-1. REPLACING THE INVERTER CONNECTOR ASSEMBLY (KDL-46S3000 ONLY) Use the following procedure to confirm that the Inverter connector is securely attached to the board.

  • Page 18: Ac Inlet Removal (Kdl-26S3000/32S3000 Only)

    KDL-26S3000/32S3000/40S3000/46S3000 1-11. AC INLET REMOVAL (KDL-26S3000/32S3000 ONLY) Remove 2 screws, +BVTP2 4X16 Remove 2 screws, +KTT 3X10 Under Cover AC Inlet 1-12. AC INLET REMOVAL (KDL-40S3000/46S3000 ONLY) Remove 2 screws, +BVTP2 4X16 Remove 2 screws, +KTT 3X10 Under Cover AC Inlet...

  • Page 19: Lcd Panel, Led And Guide Light Removal (Kdl-26S3000/32S3000 Only)

    KDL-26S3000/32S3000/40S3000/46S3000 1-13. LCD PANEL, LED AND GUIDE LIGHT REMOVAL (KDL-26S3000/32S3000 ONLY) Remove 2 screws, +PSW M4X8 Remove 2 screws, +BVTP2 4X16 Remove 2 screws, +BVTP2 4X16 Remove 2 screws, +PSW M4X8 Remove 3 screws, +BVTP2 4X16 Remove ornamental panel and slide out LED Guide and Light Guide...

  • Page 20: Lcd Panel, Led And Guide Light Removal (Kdl-40S3000/46S3000 Only)

    KDL-26S3000/32S3000/40S3000/46S3000 1-14. LCD PANEL, LED AND GUIDE LIGHT REMOVAL (KDL-40S3000/46S3000 ONLY) Remove 2 screws from Bezel and Top Brackets, +BVTP2 4X16 Remove 4 screws from Top Brackets, +PSW M5X8 Remove 4 screws from Bottom Brackets, + PSW M5X12 Remove 4 screws from Stand Holders, +PSW M5X16...

  • Page 21: Inverter Board Removal

    KDL-26S3000/32S3000/40S3000/46S3000 1-15. INVERTER BOARD REMOVAL CAUTION: Be sure to identify the inverter cover screws before proceeding. DO NOT remove the screws securing the plastic strip holding the lamp sockets. Remove screws securing the inverter cover. Remove screws securing the inverter board...

  • Page 22: Wire Dressing

    KDL-26S3000/32S3000/40S3000/46S3000 WIRE DRESSING KDL-26S3000 ONLY OVERALL VIEW KDL-26S3000/32S3000/40S3000/46S3000...
  • Page 23 KDL-26S3000/32S3000/40S3000/46S3000 KDL-26S3000 ONLY H3 BOARD HARNESS OPERATION PROCESS 1. Apply Sheet Core C to edge of Panel to cover sharp edge of panel. Use ribs on bezel (w/o screw boss) as a guide to center tape. 2. Use 2nd UL Tape on H3-Bd harness to align with edge of panel.
  • Page 24 KDL-26S3000/32S3000/40S3000/46S3000 KDL-26S3000 ONLY H3 BOARD HARNESS (CONTINUED) OPERATION PROCESS Sheet Core C 1. Apply Sheet Core C as Shown on H3-Bd Use Panel "bumps" as tape guide. Harness 2. Make sure wires do not cross over "bumps" in the Panel. LVDS cable will be attached to bumps (with 3x5mm screw-pinch points).
  • Page 25 KDL-26S3000/32S3000/40S3000/46S3000 KDL-26S3000 ONLY H4 BOARD OPERATION PROCESS 1. Install H4-Bd. Be careful to align Plastic clip at bottom of bezel with notch in PWB. 2. Use LCD Tape to hold H4-Bd wires to edge of the RIGHT Speaker. KDL-26S3000/32S3000/40S3000/46S3000...
  • Page 26 KDL-26S3000/32S3000/40S3000/46S3000 KDL-26S3000 ONLY INVERTER CONNECTOR OPERATION PROCESS Install/Wire Dress Harnesses as shown. CAUTION: Make sure INVERTER CONN. is Fully LOCKED!! CAUTION: Make Sure Inverter Connector is Fully LOCKED! KDL-26S3000/32S3000/40S3000/46S3000...
  • Page 27 KDL-26S3000/32S3000/40S3000/46S3000 KDL-26S3000 ONLY H4 BOARD AND RIGHT SPEAKER OPERATION PROCESS Wire Dress Right Speaker wires and H4 cables in G3-Bd clips (green arrows). NOTE: Rt. Spkr. Wires are dressed ONLY in far right clip on G-Bracket Apply LCD Tape to Corner of G-Bracket to keep wires from touching sharp edge of Lower LCD Bracket.
  • Page 28 KDL-26S3000/32S3000/40S3000/46S3000 KDL-26S3000 ONLY CORE BLOCK HARNESS OPERATION PROCESS Route/Dress Harnesses connected to Core Block as Shown NOTE Order & Direction of Cables in plastic Clip on Shield Case. Keep Cables BELOW level of Shield Case (Pinch Points) NOTE order and direction of cables!
  • Page 29 KDL-26S3000/32S3000/40S3000/46S3000 KDL-26S3000 ONLY G1D BOARD OPERATION PROCESS CAUTION: Make Sure Inverter Conn ON G-Bd is Fully LOCKED! 1. Install/Wire Dress Harnesses as shown. Dress all G-Bd to BU-Bd cables in 9mm Purselock. 2. CAUTION: Make sure INVERTER CONN. Use end of UL Tape on Cables to is Fully LOCKED!! position Purselock.
  • Page 30 KDL-26S3000/32S3000/40S3000/46S3000 KDL-26S3000 ONLY G1D BOARD (CONTINUED) OPERATION PROCESS Install AC Inlet Connector and dress as shown. Dress all H4/Right Speaker/AC Inlet cables in G-Bracket Clip Make Sure Earth GND wire is screwed into Lower LCD Bracket. Dress Right Speaker/H4/AC Inlet cables in G-Bracket Clip.
  • Page 31 KDL-26S3000/32S3000/40S3000/46S3000 KDL-26S3000 ONLY SPEAKER HARNESS OPERATION PROCESS Wire Dress Speaker Cables as shown. BOTH R/L cables are dressed in FGC-3 conductive clip. Right Speaker wires and H4-Bd cables are dressed UNDER AC Inlet. TORQUE SPECIFICATION Torque: 6kg.cm (+-1.0kg.cm) RIGHT SPEAKER Cables Right Speaker Wires and H4 Cables are dressed UNDER AC INLET.
  • Page 32 KDL-26S3000/32S3000/40S3000/46S3000 KDL-26S3000 ONLY LEFT SPEAKER HARNESS OPERATION PROCESS Dress LEFT speaker harness as shown KDL-26S3000/32S3000/40S3000/46S3000...
  • Page 33 KDL-26S3000/32S3000/40S3000/46S3000 KDL-26S3000 ONLY U1 BOARD OPERATION PROCESS Wire route/dress 20P U-Bd Harness as shown. Put attention on the DIRECTION of the wires when dressing in clips. KDL-26S3000/32S3000/40S3000/46S3000...
  • Page 34 KDL-26S3000/32S3000/40S3000/46S3000 KDL-26S3000 ONLY U1 BOARD (CONTINUED) OPERATION PROCESS Wire route ESD GND wire as shown (NOTE: Actual Part will have RED insulation) Use 3x12mm screw to fix ring terminal in U1 Bracket TORQUE SPECIFICATION Torque: 3mm Screw: 6kg-cm KDL-26S3000/32S3000/40S3000/46S3000...
  • Page 35 KDL-26S3000/32S3000/40S3000/46S3000 KDL-26S3000 ONLY H1 BOARD OPERATION PROCESS NOTE which connector Dress/Route H1-Bd harness as shown cables are attached to on photo. on H1-Bd. NOTE: Put attention on SLACK of cable. KDL-26S3000/32S3000/40S3000/46S3000...
  • Page 36 KDL-26S3000/32S3000/40S3000/46S3000 KDL-26S3000 ONLY LVDS CABLE OPERATION PROCESS Route LVDS Harness from BU-Board (CN4500) as shown. CAUTION: Keep LVDS Wires AWAY from Memory IC and JIG Connectors! CAUTION: Keep LVDS Cables AWAY from JIG Connectors and Memory IC. KDL-26S3000/32S3000/40S3000/46S3000...
  • Page 37 KDL-26S3000/32S3000/40S3000/46S3000 KDL-26S3000 ONLY LVDS CABLE (CONTINUED) OPERATION PROCESS Route LVDS Cable as Shown Put attention to the Cable (ABOVE or BELOW) other cables. TORQUE SPECIFICATION Torque: 3mm Screw: 6kg-cm NOTE COLOR of the Ground Tabs (Gold) Use 3x8mm screws to fix tabs.

  • Page 38: Kdl-32S3000 Only

    KDL-26S3000/32S3000/40S3000/46S3000 KDL-32S3000 ONLY OVERALL VIEW KDL-26S3000/32S3000/40S3000/46S3000...
  • Page 39 Align top of UL tape with "Score Line" on Panel and center of "Circle" on Panel Frame. Make sure 1st tape is below himelon tape on panel edge. Use boss and SONY emblem hole on bezel to align UL tape on harness. KDL-26S3000/32S3000/40S3000/46S3000...
  • Page 40 KDL-26S3000/32S3000/40S3000/46S3000 KDL-32S3000 ONLY H4 BOARD OPERATION PROCESS 1. Install H4-Bd BEFORE Installing the speakers/baffles. 2. Apply LCD Tape on SIDE of the magnet on Rt. Speaker to hold the H4 Cables. 3. MAKE SURE there is slack in the cable between the H4 Connector and LCD Tape.
  • Page 41 KDL-26S3000/32S3000/40S3000/46S3000 KDL-32S3000 ONLY H4 BOARD AND RIGHT SPEAKER OPERATION PROCESS Wire Dress Rt. Speaker wires and H4 cables in G-Bracket clips (x3) Dress BOTH H4/Speaker Cables in 3 plastic NOTE: Rt. Spkr. Wires are NOT dressed clips on G-Bracket. in far LEFT G-Bracket clip! NOTE: Speaker cables are NOT dressed inside far left clip on G-Bracket.
  • Page 42 KDL-26S3000/32S3000/40S3000/46S3000 KDL-32S3000 ONLY H4 BOARD AND RIGHT SPEAKER (CONTINUED) OPERATION PROCESS 1. Wire Dress Right Speaker wires and H4 NOTE BOTH H4-Bd and Rt. Speaker cables cables in side clamp (white) and G3-Bd are dressed UNDER AC Inlet and in G-Brkt bracket clip (black).
  • Page 43 KDL-26S3000/32S3000/40S3000/46S3000 KDL-32S3000 ONLY CORE BLOCK HARNESS OPERATION PROCESS Route/Dress Harnesses connected to Core Block as Shown NOTE Order & Direction of Cables in plastic Clip on Shield Case. DRESS CABLES 1st DRESS CABLES LAST ON TOP ALL CABLES. DRESS CABLES 3rd...
  • Page 44 KDL-26S3000/32S3000/40S3000/46S3000 KDL-32S3000 ONLY CORE BLOCK HARNESS (CONTINUED) OPERATION PROCESS Route/Dress Core-Block cables as shown Put Attention on DIRECTION of cables in G-Bracket. Put Attention on the position of the Sheet Core C and routing of the Cables between Core Block and G1-Bracket.
  • Page 45 KDL-26S3000/32S3000/40S3000/46S3000 KDL-32S3000 ONLY G1H BOARD OPERATION PROCESS Install/Wire Dress Harnesses as shown. CAUTION: Make sure INVERTER CONN. is Fully LOCKED!! G1H- NOTE: NEW G-Bracket Change! Inverter wire is NOT dressed in 1st clip. Inverter wires are dressed in cut-out on...
  • Page 46 KDL-26S3000/32S3000/40S3000/46S3000 KDL-32S3000 ONLY SPEAKER HARNESS OPERATION PROCESS 1. Wire Dress Speaker Cables as shown. 2. BOTH R/L cables are dressed in FGC-3 conductive clip. 3. Apply LCD TAPE to BOTH H4-Bd AND Right Speaker Wires. TORQUE SPECIFICATION TORQUE: 6kg.cm (+-1.0kg.cm) Apply Sheet Core C to BOTH H4/H3 AND Right Speaker Wires.
  • Page 47 KDL-26S3000/32S3000/40S3000/46S3000 KDL-32S3000 ONLY LEFT SPEAKER HARNESS OPERATION PROCESS Dress LEFT speaker harness as shown PUSH SIDE CLAMP THIS DIRECTION TO LOCK!! Side Clamp Installed by SBC PLANT! KDL-26S3000/32S3000/40S3000/46S3000...
  • Page 48 KDL-26S3000/32S3000/40S3000/46S3000 KDL-32S3000 ONLY U1 BOARD OPERATION PROCESS 1. Apply Sheet Core A to Panel in location where U1 bracket is to be installed (Use edges of panel as guide) 2. Make sure DTT Shield has Sheet Core C installed as per diagram.
  • Page 49 KDL-26S3000/32S3000/40S3000/46S3000 KDL-32S3000 ONLY U1 BOARD (CONTINUED) OPERATION PROCESS 1. Wire route ESD GND wire as shown (NOTE: Actual Part will have RED insulation) 2. Use 3x12mm screw to fix ring terminal in U1 Bracket TORQUE SPECIFICATION 3mm TORQUE: 6.0kg-cm (+-1.0kg-cm)
  • Page 50 KDL-26S3000/32S3000/40S3000/46S3000 KDL-32S3000 ONLY H1 BOARD OPERATION PROCESS 1. Dress/Route H1-Bd harness as shown on photo. 2. NOTE: Put attention on SLACK of cable. Between Connector on H1 and tape there is slack in wire. Plastic Side Clamp. Between tape/clamp there is slack.
  • Page 51 KDL-26S3000/32S3000/40S3000/46S3000 KDL-32S3000 ONLY LVDS CABLE OPERATION PROCESS 1. Route 40P LVDS Cable between BU-Bd and TCON as shown. 2. Apply 3x8mm Screw (2-places) to ground LVDS cable. NOTE: LVDS Cable is UNDER G1/U-Bd cables Put Attention on Routing of Cable.
  • Page 52 KDL-26S3000/32S3000/40S3000/46S3000 KDL-32S3000 ONLY LVDS CABLE (CONTINUED) OPERATION PROCESS Route LVDS Harness from BU-Board (CN4500) as shown. CAUTION: Keep LVDS Wires AWAY from Memory IC and JIG Connectors! CAUTION: Keep LVDS Cables AWAY from JIG Connectors and Memory IC. KDL-26S3000/32S3000/40S3000/46S3000...
  • Page 53 KDL-26S3000/32S3000/40S3000/46S3000 KDL-32S3000 ONLY VESA BRACKET GROUND WIRE OPERATION PROCESS 3x5mm Attach ESD Grounding wire as shown Install screw to GND Tab shown. on panel above BH-Bd Shield Case. NOTE: 3x8mm AND 3x5mm Screws are used!! TORQUE SPECIFICATION TORQUE: 6.0kg.cm (+-1.0kg.cm)

  • Page 54: Kdl-40S3000 Only

    KDL-26S3000/32S3000/40S3000/46S3000 KDL-40S3000 ONLY OVERALL VIEW × KDL-26S3000/32S3000/40S3000/46S3000...
  • Page 55 KDL-26S3000/32S3000/40S3000/46S3000 KDL-40S3000 ONLY H3 BOARD HARNESS OPERATION PROCESS 1. Apply Sheet Core C to edge of Panel to cover sharp edge of panel. Use ribs on bezel (w/o screw boss) as a guide to center tape. Use H3/H4 Harness "Split" as reference for top of Cushion D Position 2.
  • Page 56 KDL-26S3000/32S3000/40S3000/46S3000 KDL-40S3000 ONLY H4 BOARD OPERATION PROCESS 1. H4-Bd should be installed BEFORE the speaker/baffles are installed 2. Be careful to align Plastic clip at left side of bezel with notch in PWB. 3. PRESS FIRMLY on PWB next to clip to seat H4-Bd.
  • Page 57 KDL-26S3000/32S3000/40S3000/46S3000 KDL-40S3000 ONLY H4 BOARD AND RIGHT SPEAKER OPERATION PROCESS Wire Dress Right Speaker wires and H4 cables in side clamp (white) and G3-Bd bracket clips (black). NOTE: ALL Wires are dressed in far left G-Bracket clip! NOTE: Keep H4 cables AWAY From INVERTER BOARD AREA! NOTE: H4-Bd/Rt.
  • Page 58 KDL-26S3000/32S3000/40S3000/46S3000 KDL-40S3000 ONLY H4 BOARD AND RIGHT SPEAKER (CONTINUED) OPERATION PROCESS NOTE BOTH H4-Bd and Rt. Speaker cables 1. Dress H4/Rt. Speaker cables in white are dressed UNDER AC Inlet side clips. 2. Dress AC Inlet Cables in Plastic clip on the G-Bracket as shown.
  • Page 59 KDL-26S3000/32S3000/40S3000/46S3000 KDL-40S3000 ONLY CORE BLOCK HARNESS OPERATION PROCESS Route/Dress Harnesses connected to Core Block as Shown NOTE Order & Direction of Cables in plastic Clip on Shield Case. Route 1st Route 3rd Route LAST Keep Cables BELOW level of Shield Case (Pinch Points)
  • Page 60 KDL-26S3000/32S3000/40S3000/46S3000 KDL-40S3000 ONLY CORE BLOCK HARNESS (CONTINUED) OPERATION PROCESS Route/Dress Core-Block cables as shown Put Attention on the position of Sheet Core C and the routing of the cables between G3-Bd and Core Block. Apply Sheet Core C to dress cables.
  • Page 61 KDL-26S3000/32S3000/40S3000/46S3000 KDL-40S3000 ONLY INVERTER BOARD AND D1 BOARD OPERATION PROCESS INVERTER INVERTER CAUTION MAKE SURE BLACK INSULATION O.K. N.G. TUBING DOES NOT TOUCH CONN BEFORE INSTALLING 2P MD CONN. AFTER INSTALLING CONNECTOR, TUBE INSULATION CAN TOUCH CONNECTOR! INSTALL INVERTER SIDE 1ST INSTALL D1-Bd SIDE 2ND O.K.
  • Page 62 KDL-26S3000/32S3000/40S3000/46S3000 KDL-40S3000 ONLY INVERTER BOARD AND D1 BOARD (CONTINUED) OPERATION PROCESS INVERTE CAUTION: MAKE SURE WHITE/PINK WIRES DO NOT CROSS CHECK INVERTER SIDE WIRES CHECK D1-Bd SIDE WIRES CAUTION: Make Sure Inverter Connector DOES NOT CROSS WHITE/PINK WIRES! CHECK BOTH SIDES OF HARNESS!
  • Page 63 KDL-26S3000/32S3000/40S3000/46S3000 KDL-40S3000 ONLY G3 BOARD AND D1 BOARD OPERATION PROCESS Install/Wire Dress Harnesses as shown. NOTE: Ferrite Core and Sheet Core A CAUTION: Make sure INVERTER CONN. Applied by SBC Plants. is Fully LOCKED!! CAUTION: Make Sure Inverter Connector is Fully LOCKED!
  • Page 64 KDL-26S3000/32S3000/40S3000/46S3000 KDL-40S3000 ONLY D1 BOARD AND INVERTER BOARD CAUTION OPERATION PROCESS MAKE SURE COLOR of UL tape is the correct color (YELLOW) for harness. Confirm wires are dressed properly in clips. Confirm 2P BD Connectors are FULLY LOCKED by pressing on BOTH locking tabs (RED ARROWS).
  • Page 65 KDL-26S3000/32S3000/40S3000/46S3000 KDL-40S3000 ONLY SPEAKER CABLES OPERATION PROCESS 1. Wire Dress Speaker Cables as shown. Lft. Speaker cable is dressed in side clamp (white plastic). 2. BOTH R/L cables are dressed in FGC-3 conductive clip. TORQUE SPECIFICATION TORQUE: 6kg.cm (+-1.0kg.cm) Lft. SPEAKER Cables...
  • Page 66 KDL-26S3000/32S3000/40S3000/46S3000 KDL-40S3000 ONLY LEFT SPEAKER HARNESS OPERATION PROCESS Dress LEFT speaker harness as shown Side Clamp Installed by Vendor. PUSH SIDE CLAMP THIS DIRECTION TO LOCK!! Side Clamp Installed by SBC PLANT! KDL-26S3000/32S3000/40S3000/46S3000...
  • Page 67 KDL-26S3000/32S3000/40S3000/46S3000 KDL-40S3000 ONLY U1 BOARD OPERATION PROCESS 1. Apply Sheet Core A to Panel in location where U2 bracket is to be installed (Use plastic ribs on bezel as guide) 2. Make sure DTT Shield has Sheet Core C Align with center of circles on Install Sheet Core C on "dimple"...
  • Page 68 KDL-26S3000/32S3000/40S3000/46S3000 KDL-40S3000 ONLY U1 BOARD (CONTINUED) OPERATION PROCESS 1. Wire route ESD GND wire as shown (NOTE: Actual Part will have BLUE insulation) 2. Use 3x12mm screw to fix ring terminal in U1 Bracket 3. Apply Sheet Core C to hold cable on panel.
  • Page 69 KDL-26S3000/32S3000/40S3000/46S3000 KDL-40S3000 ONLY H1 BOARD OPERATION PROCESS 1. Dress/Route H1-Bd harness as shown on photo. 2. NOTE: Put attention on SLACK of cable. Between Connector on H1 and tape there is slack in wire. Between tapes there is a little slack.
  • Page 70 KDL-26S3000/32S3000/40S3000/46S3000 KDL-40S3000 ONLY LVDS CABLE OPERATION PROCESS 1. Route 40P LVDS Cable between BU-Bd and TCON as shown. 2. Apply 3x8mm Screw (2-places) to ground LVDS cable. G1 to BU cables are on TOP of LVDS. H3-Bd cables are UNDER LVDS.
  • Page 71 KDL-26S3000/32S3000/40S3000/46S3000 KDL-40S3000 ONLY LVDS CABLE (CONTINUED) OPERATION PROCESS Route LVDS Harness from BU-Board (CN4500) as shown. CAUTION: Keep LVDS Wires AWAY from Memory IC and JIG Connectors! CAUTION: Keep LVDS Cables AWAY from JIG Connectors and Memory IC. KDL-26S3000/32S3000/40S3000/46S3000...

  • Page 72: Kdl-46S3000 Only

    KDL-26S3000/32S3000/40S3000/46S3000 KDL-46S3000 ONLY OVERALL VIEW KDL-26S3000/32S3000/40S3000/46S3000...
  • Page 73 KDL-26S3000/32S3000/40S3000/46S3000 KDL-46S3000 ONLY H3 BOARD HARNESS OPERATION PROCESS 1. Apply Sheet Core C to edge of Panel to cover sharp edge of panel. Use rib on bezel (w/o screw boss) as a Use H3/H4 Harness "Split" as reference guide to center tape.
  • Page 74 KDL-26S3000/32S3000/40S3000/46S3000 KDL-46S3000 ONLY H4 BOARD OPERATION PROCESS 1. H4-Bd should be installed BEFORE the speaker/baffles are installed 2. Be careful to align Plastic clip at left side of bezel with notch in PWB. 3. PRESS FIRMLY on PWB next to clip to seat H4-Bd.
  • Page 75 KDL-26S3000/32S3000/40S3000/46S3000 KDL-46S3000 ONLY H4 BOARD AND RIGHT SPEAKER OPERATION PROCESS Wire Dress Right Speaker wires and H4 Apply Sheet Core C to hold Rt Speaker cables in side clamp (white) and G3-Bd Align horizontally with Edge of G3 Bracket. bracket clips (black).
  • Page 76 KDL-26S3000/32S3000/40S3000/46S3000 KDL-46S3000 ONLY H4 BOARD AND RIGHT SPEAKER (CONTINUED) OPERATION PROCESS DO NOTDress AC Inlet Cables Dress H4/Rt. Speaker cables in white side clips. in M-TYPE CLAMP (G3-Bd) Dress AC Inlet Cables in Plastic clip on the G-Bracket as shown.
  • Page 77 KDL-26S3000/32S3000/40S3000/46S3000 KDL-46S3000 ONLY CORE BLOCK HARNESS OPERATION PROCESS Route/Dress Harnesses connected to Core Block as Shown NOTE Order & Direction of Cables in plastic Clip on Shield Case. DRESS CABLES 1st DRESS CABLES LAST ON TOP ALL CABLES. DRESS CABLES 3rd...
  • Page 78 KDL-26S3000/32S3000/40S3000/46S3000 KDL-46S3000 ONLY CORE BLOCK HARNESS (CONTINUED) OPERATION PROCESS 1. Route/Dress Core-Block cables as shown Apply LCD Tape to dress H1 cables. Use UL tape on H1 cables as Ref. 2. Put Attention on the position of Sheet Core Use "Score Line" in Panel as Ref.
  • Page 79 KDL-26S3000/32S3000/40S3000/46S3000 KDL-46S3000 ONLY INVERTER BOARD AND D1 BOARD OPERATION PROCESS INVERTER INVERTER CAUTION MAKE SURE BLACK INSULATION O.K. N.G. TUBING DOES NOT TOUCH CONN BEFORE INSTALLING 2P MD CONN. AFTER INSTALLING CONNECTOR, TUBE INSULATION CAN TOUCH CONNECTOR! INSTALL INVERTER SIDE 1ST INSTALL D1-Bd SIDE 2ND O.K.
  • Page 80 KDL-26S3000/32S3000/40S3000/46S3000 KDL-46S3000 ONLY G3 BOARD AND D1 BOARD OPERATION PROCESS Install/Wire Dress Harnesses as shown. NOTE: Ferrite Core and Sheet Core A Applied by SBC Plants. CAUTION: Make sure INVERTER CONN. is Fully LOCKED!! CAUTION: Make Sure Inverter Connector is Fully LOCKED!
  • Page 81 KDL-26S3000/32S3000/40S3000/46S3000 KDL-46S3000 ONLY G3 BOARD AND D1 BOARD (CONTINUED) OPERATION PROCESS Install/Wire Dress Harnesses as shown. CAUTION: 13P AND 3P VH (w/TUBING) DRESSED UNDER ALL CAUTION: Make sure 13P AND 3P VH (w/TUBING) IS DRESSED BELOW CABLES. ALL HARNESS (NEED TO TOUCH PANEL).
  • Page 82 KDL-26S3000/32S3000/40S3000/46S3000 KDL-46S3000 ONLY G3 BOARD AND D2 BOARD OPERATION PROCESS 1. MAKE SURE COLOR of UL tape is the correct color (RED) for harness. Confirm wires are dressed properly in clips. 2. Dress D2 harness as shown 3. Apply Sheet Core C to 3P VH Conn Assy. As shown.
  • Page 83 KDL-26S3000/32S3000/40S3000/46S3000 KDL-46S3000 ONLY INVERTER BOARD AND D2 BOARD OPERATION PROCESS INVERTER INVERTER O.K. N.G. CAUTION MAKE SURE BLACK INSULATION TUBING DOES NOT TOUCH CONN BEFORE INSTALLING 2P MD CONN. AFTER INSTALLING CONNECTOR, TUBE INSULATION CAN TOUCH CONNECTOR! INSTALL INVERTER SIDE 1ST INSTALL D1-Bd SIDE 2ND O.K.
  • Page 84 KDL-26S3000/32S3000/40S3000/46S3000 KDL-46S3000 ONLY INVERTER BOARD, D1 BOARD AND D2 BOARD OPERATION PROCESS INVERTE CAUTION: MAKE SURE WHITE/PINK WIRES DO NOT CROSS. CHECK INVERTER TO D1 WIRES CHECK INVERTER TO D2 WIRES CAUTION: Make Sure Inverter Connector DOES NOT CROSS WHITE/PINK WIRES!
  • Page 85 KDL-26S3000/32S3000/40S3000/46S3000 KDL-46S3000 ONLY D2 BOARD OPERATION PROCESS 1. MAKE SURE COLOR of UL tape is the correct color (WHITE/BLACK) for harness. Confirm wires are dressed properly in clips. 2. Dress D2 harness as shown 3. Apply Sheet Core C to 3P VH Conn Assy. As shown.
  • Page 86 KDL-26S3000/32S3000/40S3000/46S3000 KDL-46S3000 ONLY D1 BOARD AND INVERTER BOARD CAUTION OPERATION PROCESS MAKE SURE COLOR of UL tape is the correct color (RED) to connect to Inverter. Confirm wires are dressed properly in clips. Confirm BLACK UL tape Connect to D1-Bd.
  • Page 87 KDL-26S3000/32S3000/40S3000/46S3000 KDL-46S3000 ONLY D1 BOARD AND INVERTER BOARD CAUTION (CONTINUED) OPERATION PROCESS MAKE SURE COLOR of UL tape is the correct color (RED/BLK) for harness. Confirm wires are dressed properly in clips. Confirm 2P BD Connectors are FULLY LOCKED by pressing on BOTH locking tabs (RED ARROWS).
  • Page 88 KDL-26S3000/32S3000/40S3000/46S3000 KDL-46S3000 ONLY D1 BOARD AND INVERTER BOARD CAUTION (CONTINUED) OPERATION PROCESS MAKE SURE COLOR of UL tape is the correct color (WHITE/BLK) for harness. Confirm wires are dressed properly in clips. Confirm 2P BD Connectors are FULLY LOCKED by pressing on BOTH locking tabs (RED ARROWS).
  • Page 89 KDL-26S3000/32S3000/40S3000/46S3000 KDL-46S3000 ONLY D2 BOARD AND INVERTER BOARD CAUTION OPERATION PROCESS 1. Wire Dress Speaker Cables as shown. Lft. Speaker cable is dressed in side clamp (white plastic). 2. BOTH R/L cables are dressed in FGC-3 conductive clip. TORQUE SPECIFICATION TORQUE: 6kg.cm (+-1.0kg.cm)
  • Page 90 KDL-26S3000/32S3000/40S3000/46S3000 KDL-46S3000 ONLY SPEAKER CABLES OPERATION PROCESS Side Clamp Installed by SBC PLANT! 1. Dress LEFT speaker harness as shown 2. Install Sheet Core C to hold BOTH U1 Gnd Wire AND Lft. Speaker wires to panel. Side Clamp Installed by Vendor.
  • Page 91 KDL-26S3000/32S3000/40S3000/46S3000 KDL-46S3000 ONLY LEFT SPEAKER HARNESS OPERATION PROCESS DO NOT allow LFT. Speaker wire (white) to cross over magnet on speaker. Keep white wire CLEAR of magnet. O.K. Spkr. Wire NO CROSS Magnet. N.G. Spkr. Wire CROSS Magnet. KDL-26S3000/32S3000/40S3000/46S3000...
  • Page 92 KDL-26S3000/32S3000/40S3000/46S3000 KDL-46S3000 ONLY U1 BOARD OPERATION PROCESS Apply Sheet Core C to Panel. 3/4/2007 LATE CHANGE: Use "Score Line" to center Tape. Use Bottom of "Dimple" to align bottom of 3x12mm Screw in this hole! tape. Make sure DTT Shield has Sheet Core C (Installed by Vendor) Wire Dress 20P Harness as shown.
  • Page 93 KDL-26S3000/32S3000/40S3000/46S3000 KDL-46S3000 ONLY U1 BOARD (CONTINUED) OPERATION PROCESS 1. Wire route ESD GND wire as shown (NOTE: Actual Part will have RED insulation) 2. Use 3x12mm screw to fix ring terminal in U1 Bracket 3. Apply Sheet Core C to hold cable on panel.
  • Page 94 KDL-26S3000/32S3000/40S3000/46S3000 KDL-46S3000 ONLY H1 BOARD OPERATION PROCESS Dress/Route H1-Bd harness as shown NOTE which connector on photo. harness is attached to on H1-Bd. NOTE: Put attention on SLACK of cable. Between Connector on H1 and tape there is slack in wire.
  • Page 95 KDL-26S3000/32S3000/40S3000/46S3000 KDL-46S3000 ONLY LVDS CABLE OPERATION PROCESS 1. Route 40P LVDS Cable between BU-Bd and TCON as shown. 2. Apply 3x8mm Screw (2-places) to ground LVDS cable. NOTE: LVDS Cable is OVER D1-Bd to D2-Bd cables G1 to BU cables are on TOP of LVDS.
  • Page 96 KDL-26S3000/32S3000/40S3000/46S3000 KDL-46S3000 ONLY LVDS CABLE (CONTINUED) OPERATION PROCESS Route LVDS Harness from BU-Board (CN4500) as shown. CAUTION: Keep LVDS Wires AWAY from Memory IC and JIG Connectors! CAUTION: Keep LVDS Cables AWAY from JIG Connectors and Memory IC. KDL-26S3000/32S3000/40S3000/46S3000...
  • Page 97 KDL-26S3000/32S3000/40S3000/46S3000 KDL-46S3000 ONLY VESA BRACKER GROUND WIRE 3x8mm Install screw to GND Tab OPERATION PROCESS on R VESA Bracket(LEFT SIDE). NOTE: This screw can be applied Attach ESD Grounding wire as shown pre-assembly shown. off-line as operation. Install Faston Tab on G3-Bd NOTE: 3x8mm Screws are located.

  • Page 98: Section 2: Service Adjustments

    KDL-26S3000/32S3000/40S3000/46S3000 SECTION 2: SERVICE ADJUSTMENTS 2-1. USING THE REMOTE COMMANDER 2-3. VIEWING THE SERVICE MENUS FOR ELECTRICAL ADJUSTMENTS Use the Remote Commander to view the BE and Digital service menus options. To adjust various set features, use the Remote Commander to put the set into service mode to display the service menus and categories.

  • Page 99: Using The Remote Commander To View Service Data

    KDL-26S3000/32S3000/40S3000/46S3000 2-4. USING THE REMOTE COMMANDER TO 1. Access Service Adjustment Mode and select the Service Menu that contains the Category with the Adjustment Item you want to change. VIEW SERVICE DATA 2. To change the Category, press 2 or 5 on the Remote Commander.

  • Page 100: Verifying Service Data Changes

    KDL-26S3000/32S3000/40S3000/46S3000 2-5. VERIFYING SERVICE DATA CHANGES 1. After completing all adjustments turn the set off with the Remote Commander and then proceed to the next step. 2. Press the following buttons on the Remote Commander within a second of each other:...

  • Page 101: Section 3: Diagrams

    KDL-26S3000/32S3000/40S3000/46S3000 SECTION 3: DIAGRAMS 3-1. CIRCUIT BOARDS LOCATION (KDL-26S3000/32S3000 Only) POWER UNIT (KDL-40S3000/46S3000 Only) (KDL-46S3000 Only) KDL-26S3000/32S3000/40S3000/46S3000...

  • Page 102: Printed Wiring Boards And Schematic Diagrams Information

    KDL-26S3000/32S3000/40S3000/46S3000 3-2. PRINTED WIRING BOARDS AND Terminal name of semiconductors in silk screen SCHEMATIC DIAGRAMS INFORMATION printed circuit ( All capacitors are in μF unless otherwise noted. pF : μμF 50WV or Circuit Device Printed symbol Terminal name Collector less are not indicated except for electrolytics and tantalums.

  • Page 103: Block Diagram

    KDL-26S3000/32S3000/40S3000/46S3000 3-3. BLOCK DIAGRAM SIGNAL FLOW DIAGRAM Audio Audio Audio Audio HDMI HDMI HDMI HDMI for PC for PC for DVI for DVI UART 8bit Multiplex BUS 4M x 32bit BE Micro MB91305 Flash Panel NAND NAND Flash Flash DDR2...

  • Page 104: Connection Diagram (Kdl-26S3000/32S3000 Only)

    KDL-26S3000/32S3000/40S3000/46S3000 CONNECTION DIAGRAM (KDL-26S3000/32S3000 ONLY) 26/32S3000 PWB Layout & Connection TO PANEL CN101 Left INV. CN2-CN9 CN4500 CN4003 CN6202 CN4002 TO PANEL CN6201 CN4001 CN3008 CN201 CN1400 CN2000 CN401 CN301 KDL-26S3000/32S3000/40S3000/46S3000...

  • Page 105: Connection Diagram (Kdl-40S3000/46S3000 Only)

    KDL-26S3000/32S3000/40S3000/46S3000 CONNECTION DIAGRAM (KDL-40S3000/46S3000 ONLY) 40/46S3000 PWB Layout & Connection CN6950 CN6704 CN6900 CN128 CN6700 TO PANEL CN6951 CN226 CN101 CN125 CN6701 Right Left CN6600 CN6707 INV. INV. CN225 CN6204 CN6502 CN126 CN6501 CN4500 CN4003 TO PANEL CN6203 CN4002 TO PANEL...

  • Page 106: Schematics And Supporting Information

    KDL-26S3000/32S3000/40S3000/46S3000 3-4. SCHEMATICS AND SUPPORTING INFORMATION BU1 BOARD SCHEMATIC DIAGRAM (1 OF 12) A_V1_IN_C,A_V1_IN_S2SW,A_V1_IN_SSW,A_V1_IN_V,A_V1_IN_Y R1003 1/16W CHIP A_V1_IN_Y R1000 R1001 R1002 C1000 0 . 0 1 1/10W 1/10W D1000 1/10W RN-CP RN-CP RN-CP MA8100-TX 0.5% 0.5% 0.5% 1608 R1005 1/16W...

  • Page 107: Bu1 Board Schematic Diagram (2 Of 12)

    KDL-26S3000/32S3000/40S3000/46S3000 BU1 BOARD SCHEMATIC DIAGRAM (2 OF 12) A_HP_OUT_R A_HP_OUT_L AUDIO_9V A_SP_OUT_R MUTE_AU13V A_SP_OUT_L PQ200WNA1ZPH — A_LINE_OUT_R I C 2005 AU_13V A_LINE_OUT_L AUDIO_13V TAS ANALOG 3.3V R 2202 L 2016 F 2000 22uH 1/16W C 2123 CHIP D3.3V D2014 C 2121 C 2159 0.

  • Page 108: Bu1 Board Schematic Diagram (3 Of 12)

    KDL-26S3000/32S3000/40S3000/46S3000 BU1 BOARD SCHEMATIC DIAGRAM (3 OF 12) << ST B Y 3.3V >> ST B Y 3.3V M24256-BWMN6TP(A) RESET R 3167 I C 3005 X 3009 1/16W EEPROM 32. 768kH z R 3144 — 2 . 2 k CHIP...

  • Page 109: Bu1 Board Schematic Diagram (4 Of 12)

    KDL-26S3000/32S3000/40S3000/46S3000 BU1 BOARD SCHEMATIC DIAGRAM (4 OF 12) JL 4508 TMDS_RX0- Y_G1 R X 0- TO HDMI JL 4509 TMDS_RX0+ PB_B1 RX0+ JL 4510 •¡ SV P-PX P DDR & CPU I/F, POWE R & GND PB_R1 TMDS_RX1- — R X 1-...

  • Page 110: Bu1 Board Schematic Diagram (5 Of 12)

    KDL-26S3000/32S3000/40S3000/46S3000 BU1 BOARD SCHEMATIC DIAGRAM (5 OF 12) — MD[19] VDDMQO MD[16] MD[18] FL4901 — MD[17] RB4904 L4901 R4900 C4906 6.3V MD[20] MD[21] MD[22] — MD[23] RB4905 MVREF VDDMQ MD[0] MD[1] MD[3] FL4900 MD[2] RB4906 — L4900 C4909 100p MD[4]...

  • Page 111: Bu1 Board Schematic Diagram (6 Of 12)

    KDL-26S3000/32S3000/40S3000/46S3000 BU1 BOARD SCHEMATIC DIAGRAM (6 OF 12) TO Trident PC-R JL5007 FB5001 0uH PC_R PC_R R5021 FB5002 0uH PC-G 1/10W D3.3V-2 RN-CP FB5000 0uH PC-B PC_G PC_G — J5000 R5022 1/10W RN-CP FB5006 PC_B PS5000 PC_B R5023 0.5A 1/10W...

  • Page 112: Bu1 Board Schematic Diagram (7 Of 12)

    KDL-26S3000/32S3000/40S3000/46S3000 BU1 BOARD SCHEMATIC DIAGRAM (7 OF 12) ST B Y 3.3V R 4048 FB 4011 1/10W L FB K 1608HS601 RN-CP 0.5% FB 4005 D3.3V R 4047 — STBY 3.3V 2 . 2 k DIMMER DIMMER 1/16W FB 4009...

  • Page 113: Bu1 Board Schematic Diagram (8 Of 12)

    KDL-26S3000/32S3000/40S3000/46S3000 BU1 BOARD SCHEMATIC DIAGRAM (8 OF 12) D2.5V — C 7077 1608 R 7047 C 7047 2 . 2 k 220p 1/16W RN-CP 0.5% R 7059 REG12V — 1/16W CHIP R 7035 R 7041 R 7048 R 7055 3 . 3 k...

  • Page 114: Bu1 Board Schematic Diagram (9 Of 12)

    KDL-26S3000/32S3000/40S3000/46S3000 BU1 BOARD SCHEMATIC DIAGRAM (9 OF 12) X IL L EON242 GROUND BAL L S ASIC CORE POWER D2.5V _A T I D1.0V D3.3V _A T I COR E _1.0V (NE E D <50mV NOI SE ) — FB 7200...

  • Page 115: Bu1 Board Schematic Diagram (10 Of 12)

    KDL-26S3000/32S3000/40S3000/46S3000 BU1 BOARD SCHEMATIC DIAGRAM (10 OF 12) — MEMORY CONFIGURATION VDDR_MEM DDR _1.8V DRAM_IF DDR2 SDRAM WAX 3 L 7431 MEM_DQA0 I C 7400 R 24 * C 7430 C 7431 DQA_0 HY B 18T C512160B F-2.5 0 . 1...

  • Page 116: Bu1 Board Schematic Diagram (11 Of 12)

    KDL-26S3000/32S3000/40S3000/46S3000 BU1 BOARD SCHEMATIC DIAGRAM (11 OF 12) DIGITAL GR APHICS OUT (DDR ) — GRAPHICS DDR->SDR LATCH EGPHSI EGPHSI D3.3V FB 7601 DV I_IF EGPV SI EGPV SI C 7611 — DVIDATA0 EGPPCI EGPPCI T C74V CX 162374(E L ,F...

  • Page 117: Bu1 Board Schematic Diagram (12 Of 12)

    KDL-26S3000/32S3000/40S3000/46S3000 BU1 BOARD SCHEMATIC DIAGRAM (12 OF 12) V IDEO_IF FRONT_END_IF — R 7712 R 7710 1/16W V I _I N0 CHIP R 7706 1/16W * C 7818 L 7801 C 7828 V I _I N1 C 7821 C 7823...
  • Page 118 KDL-26S3000/32S3000/40S3000/46S3000 [I/O JACKS, AUDIO, MAIN MICRO CONTROLLER, TRIDENT, DDR_SDRAM 128 MBIT, HDMI EPC, POWER EDC_ALERT, POWER, RESET, X242 POWER, PLL, FLEXBUS, USB, PERIPHERALS, DDR, FLASH, NVM, DIGITAL IF, EJTAG, AVOUT, FE, TUNER] [I/O JACKS, AUDIO, MAIN MICRO CONTROLLER, TRIDENT, DDR_SDRAM 128 MBIT, HDMI EPC, POWER EDC_ALERT, POWER, RESET, X242 POWER, PLL, FLEXBUS, USB, PERIPHERALS, DDR, FLASH, NVM, DIGITAL IF, EJTAG, AVOUT, FE, TUNER]...

  • Page 119: D1 Board Schematic Diagram (Kdl-40S3000 Only)

    KDL-26S3000/32S3000/40S3000/46S3000 D1 BOARD SCHEMATIC DIAGRAM (KDL-40S3000 ONLY) — CN6600 3 9 2 . 0 TO G3 PFC_OUT CN6502 L6600 PRI_GND 100uH C6600 450V 3LN02C-TB-E R6700 4 . 7 1/10W — RN-CP VCC_12V C6709 6 . 3 k V D6701 D6704...
  • Page 120 KDL-26S3000/32S3000/40S3000/46S3000 [INVERTER] COMPONENT SIDE (KDL-40S3000 ONLY) CN6702 CN6700 JW6702 R6804 JW6743 JW6703 T6801 JW6756 EY6700 EY6701 EY6702 EY6703 T6600 EY6704 EY6705 EY6706 EY6707 C6759 JW6710 00_8 JW6735 JW6754 BALANCER_ERR REG12V JW6755 0-000-000-08 INV_ERR BACK_LIGHT (000000008) DIMMER ET6701 JW6731 JW6738 JW6757...
  • Page 121 KDL-26S3000/32S3000/40S3000/46S3000 [INVERTER] CONDUCTOR SIDE (KDL-40S3000 ONLY) CN6702 D6705 D6704 CN6700 C6712 JR6704 C6714 D6703 ET6700 C6707 C6706 R6763 JR6717 Q6716 C6742 R6822 D6702 JL6708 R6755 R6823 C6786 C6609 C6735 R6821 R6804 Q6714 JL6717 JL6718 C6745 IC6702 C6759 JL6715 BALANCER _ERR...

  • Page 122: D2 Board Schematic Diagram (Kdl-46S3000 Only)

    KDL-26S3000/32S3000/40S3000/46S3000 D2 BOARD SCHEMATIC DIAGRAM (KDL-46S3000 ONLY) CN6900 3 9 1 . 0 — PFC_OUT TO G3 CN6501 L6900 PRI_GND 100uH C6900 450V FB6904 FB6906 R6950 4 . 7 1/10W RN-CP MA8051-M-TX D6951 C6958 VCC_12V D6912 — S3L60F 6 . 3 k V...
  • Page 123 KDL-26S3000/32S3000/40S3000/46S3000 [INVERTER] [INVERTER] COMPONENT SIDE (KDL-46S3000 ONLY) CONDUCTOR SIDE (KDL-46S3000 ONLY) 00_8 JW6952 CN6951 CN6951 D6955 D6954 ET6951 C6961 C6959 C6962 C6963 ET6951 C6905 00_8 PF LP 0-000-000-08 0-000-000-08 A-1221- (000000008) (000000008) T6951 JL6960 JL6959 EY6962 EY6963 EY6964 EY6965 R6962...

  • Page 124: G1D Board Schematic Diagram (Kdl-26S3000 Only)

    KDL-26S3000/32S3000/40S3000/46S3000 G1D BOARD SCHEMATIC DIAGRAM (KDL-26S3000 ONLY) This board is manufactured by a 3rd party. Component level repair information is not available. 470p C244 1nF 100V K D241 LL4148-GS08 C821 C822 R841 CN1:1 2.5 L SMT-39RH-LPXXXX LF-R18-DP6101 LF-R22-LP3003-11 D905 D242...

  • Page 125: G1H Board Schematic Diagram (Power Supply) (Kdl-32S3000 Only)

    KDL-26S3000/32S3000/40S3000/46S3000 G1H BOARD SCHEMATIC DIAGRAM (POWER SUPPLY) (KDL-32S3000 ONLY) This board is manufactured by a 3rd party. Component level repair information is not available. [POWER SUPPLY] PWB IS NOT AVAILABLE KDL-26S3000/32S3000/40S3000/46S3000...

  • Page 126: G3 Board Schematic (Power Supply) (Kdl-40S3000/46S3000 Only)

    KDL-26S3000/32S3000/40S3000/46S3000 G3 BOARD SCHEMATIC (POWER SUPPLY) (KDL-40S3000/46S3000 ONLY) Mount Mecha A6000 214976631 D6000 L6501 t @ X g 300uH C6515 C6516 R6106 L6150 Mount Mecha A6150 234989201 D6151 CN6003 470p 470p R6524 R6014 C6019 D6151 6 . 8 1/10W D4SBS6 0 .
  • Page 127 KDL-26S3000/32S3000/40S3000/46S3000 [POWER SUPPLY] [POWER SUPPLY] COMPONENT SIDE (KDL-40S3000/46S3000 ONLY) COMPONENT SIDE (KDL-40S3000/46S3000 ONLY) A6003 CN6004 CN6004 A6002 A6003 A6002 A- 1221- ET6000 FB6001 FB6001 EY6517 C6157 T6100 CN6204 T6100 CN6204 A6017 C6023 PS6152 C6023 PS6152 CN6501 CN6502 CN6502 CN6501 JL6156...

  • Page 128: H1 Board Schematic Diagram

    KDL-26S3000/32S3000/40S3000/46S3000 H1 BOARD SCHEMATIC DIAGRAM POWER — H1 BOARD S101 USER CONTROL — HOME INPUT SEL VOL+ VOL- MENU TO BU1 WEGAGATE POWER INT CN3008 KEY1 — R107 R102 CN101 S104 S107 S106 S105 S103 S102 — R104 R101 R105 R103 1 .
  • Page 129 KDL-26S3000/32S3000/40S3000/46S3000 [USER CONTROL] COMPONENT SIDE VOL+ R102 S104 VOL- VIA G[CV OK S105 R103 INPUT SEL S103 R108 S106 R101 R107 S107 R104 S101 POWER S102 HOME 1-872-981-11 A-1220- MENU C103 (172841011) WEGAGATE [USER CONTROL] CONDUCTOR SIDE CN102 CN101 JL101...

  • Page 130: H3 Board Schematic Diagram

    KDL-26S3000/32S3000/40S3000/46S3000 H3 BOARD SCHEMATIC DIAGRAM STBY3.3V REC/RESERVE STBY_LED — TO BU1 CN3008 ON_TIMER PWR/RESERVE PICTURE_OFF R303 R304 R305 BL_IN R301 R302 2 . 2 k 1/10W 1/10W 1/10W RN-CP 1/10W 1/10W RN-CP RN-CP VD3.3V RN-CP RN-CP — D305 D302 CN301...
  • Page 131 KDL-26S3000/32S3000/40S3000/46S3000 [OPTICAL SENSOR, LED] COMPONENT SIDE TIMER D308 (172841011) Optical 1-872-982-11 Sensor PICOFF R302 JL305 DATA STBY R303 TREC C320 R301 IC320 A-1220-319-A R304 [OPTICAL SENSOR, LED] CONDUCTOR SIDE Q304 EP-(GW+GN) D306 D303 1-872-982-11 CN301 C323 R325 R326 D301 CN301...

  • Page 132: H4 Board Schematic Diagram

    KDL-26S3000/32S3000/40S3000/46S3000 H4 BOARD SCHEMATIC DIAGRAM GP1UE26RK0VF IC401 — SIRCS TO BU1 STBY3.3V CN3008 — R402 C402 R401 1/10W 6 . 3 V 1/10W RN-CP CN401 RN-CP 2012 H 4 S i r c s C401 — 220p 1608 A-1220-320-A H4 —...
  • Page 133 KDL-26S3000/32S3000/40S3000/46S3000 [SIRCS] COMPONENT SIDE 1-873-380-11 A-1220 -320-A EP-(GW+GN) [SIRCS] CONDUCTOR SIDE R402 KDL-26S3000/32S3000/40S3000/46S3000...

  • Page 134: U1 Board Schematic Diagram

    KDL-26S3000/32S3000/40S3000/46S3000 U1 BOARD SCHEMATIC DIAGRAM C218 1000p 1608 J202 — R219 R220 C215 VD201 1000p CHIP CHIP 1608 VD202 VD203 D3.3V GND_D — R203 V2_IN_AU_L 1/10W RN-CP D3.3V R200 R201 R202 C200 AU_IN_GND 0 . 0 1 VD206 1/10W 1/10W...
  • Page 135 KDL-26S3000/32S3000/40S3000/46S3000 [VIDEO IN 2] COMPONENT SIDE J201 J202 JL205 JL205 JL203 JL203 JL204 JL204 JL209 JL209 (172841113) 1-872-983-13 JL211 JL211 CN202 [VIDEO IN 2] CONDUCTOR SIDE J201 J201 D202 D202 cam3 cam3 JL206 JL206 R205 R205 C201 C201 R221 R221...

  • Page 136: Semiconductors

    KDL-26S3000/32S3000/40S3000/46S3000 3-5. SEMICONDUCTORS – KDL-26S3000/32S3000/40S3000/46S3000...

  • Page 137: Section 4: Exploded Views

    REF. NO. PART NO. DESCRIPTION [ASSEMBLY INCLUDES] REF. NO. PART NO. DESCRIPTION [ASSEMBLY INCLUDES] (Please review the Sony Electronics Service Information website for any additional service information.) 3-100-157-01 COVER, REAR (26) 3-215-345-01 LABEL, INFORMATION (KDL-26S3000 ONLY) (KDL-32S3000 ONLY) 7-685-648-79 SCREW +BVTP 3X12 TYPE2 TT(B)

  • Page 138: Bezel Assembly And Lcd Panel

    See Appendix A: Encryption Key Components in the back of this manual. 4-2. BEZEL ASSEMBLY AND LCD PANEL (Please review the Sony Electronics Service Information website for any additional service information.) 2-580-640-01 SCREW, +BVTP2 4X16 REF. NO.

  • Page 139: Chassis (Kdl-26S3000/32S3000 Only)

    See Appendix A: Encryption Key Components in the back of this manual. 4-3. CHASSIS (KDL-26S3000/32S3000 ONLY) (Please review the Sony Electronics Service Information website for any additional service information.)

  • Page 140: Chassis (Kdl-40S3000/46S3000 Only)

    See Appendix A: Encryption Key Components in the back of this manual. 4-4. CHASSIS (KDL-40S3000/46S3000 ONLY) (Please review the Sony Electronics Service Information website for any additional service information.) 2-580-640-01 SCREW, +BVTP2 4X16 2-674-965-41...

  • Page 141: Connectors (Kdl-26S3000/32S3000 Only)

    See Appendix A: Encryption Key Components in the back of this manual. 4-5. CONNECTORS (KDL-26S3000/32S3000 ONLY) (Please review the Sony Electronics Service Information website for any additional service information.) REF.

  • Page 142: Connectors (Kdl-40S3000/46S3000 Only)

    See Appendix A: Encryption Key Components in the back of this manual. 4-6. CONNECTORS (KDL-40S3000/46S3000 ONLY) (Please review the Sony Electronics Service Information website for any additional service information.) REF. NO. PART NO. DESCRIPTION [ASSEMBLY INCLUDES] REF.

  • Page 143: Speakers

    See Appendix A: Encryption Key Components in the back of this manual. 4-7. SPEAKERS (Please review the Sony Electronics Service Information website for any additional service information.) 2-580-640-01 SCREW, +BVTP2 4X16 2-580-600-01...

  • Page 144: Section 5: Electrical Parts List

    CERAMIC CHIP 0.001μF 10% C1723 1-100-905-11 CERAMIC CHIP 0.001μF 10% A-1268-869-A BU1 BOARD, MOUNTED (SVC) C1724 1-100-912-11 CERAMIC CHIP 1μF (KDL-26S3000 ONLY) A-1257-244-A BU1 BOARD, MOUNTED (SVC) C1725 1-100-912-11 CERAMIC CHIP 1μF (KDL-32S3000 ONLY) C2013 1-126-392-11 ELECT CHIP 100μF 6.3V...
  • Page 145 KDL-26S3000/32S3000/40S3000/46S3000 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES C2068 1-100-905-11 CERAMIC CHIP 0.001μF 10% C2132 1-115-340-11 CERAMIC CHIP 0.22μF C2069 1-112-064-11 CERAMIC CHIP 2.2μF C2133 1-115-340-11 CERAMIC CHIP 0.22μF C2134 1-112-064-11 CERAMIC CHIP 2.2μF C2070...
  • Page 146 KDL-26S3000/32S3000/40S3000/46S3000 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES C3012 1-100-905-11 CERAMIC CHIP 0.001μF 10% C4041 1-112-774-11 CERAMIC CHIP 470pF C3014 1-100-906-11 CERAMIC CHIP 0.01μF C4042 1-112-774-11 CERAMIC CHIP 470pF C4043 1-112-774-11 CERAMIC CHIP 470pF C3015...
  • Page 147 KDL-26S3000/32S3000/40S3000/46S3000 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES C4726 1-100-916-11 CERAMIC CHIP 0.1μF C4917 1-164-874-11 CERAMIC CHIP 100pF C4730 1-100-905-11 CERAMIC CHIP 0.001μF 10% C4918 1-164-874-11 CERAMIC CHIP 100pF C4919 1-164-874-11 CERAMIC CHIP 100pF C4731...
  • Page 148 KDL-26S3000/32S3000/40S3000/46S3000 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES C7012 1-100-916-11 CERAMIC CHIP 0.1μF C7059 1-165-908-11 CERAMIC CHIP 1μF C7013 1-114-214-81 CERAMIC CHIP 470pF C7060 1-165-908-11 CERAMIC CHIP 1μF C7061 1-114-325-11 CERAMIC CHIP 0.1μF C7015 1-100-905-11 CERAMIC CHIP 0.001μF 10%...
  • Page 149 KDL-26S3000/32S3000/40S3000/46S3000 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES C7207 1-100-916-11 CERAMIC CHIP 0.1μF C7252 1-100-916-11 CERAMIC CHIP 0.1μF C7208 1-126-210-21 ELECT CHIP 220μF C7253 1-100-916-11 CERAMIC CHIP 0.1μF C7254 1-100-916-11 CERAMIC CHIP 0.1μF C7209 1-100-916-11 CERAMIC CHIP 0.1μF...
  • Page 150 KDL-26S3000/32S3000/40S3000/46S3000 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES C7410 1-100-916-11 CERAMIC CHIP 0.1μF C7720 1-165-908-11 CERAMIC CHIP 1μF C7411 1-114-130-11 CERAMIC CHIP 1μF 6.3V C7800 1-100-916-11 CERAMIC CHIP 0.1μF C7801 1-100-916-11 CERAMIC CHIP 0.1μF C7412...
  • Page 151 KDL-26S3000/32S3000/40S3000/46S3000 NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les remplacer mark are critical for safety. Replace only que par une piece portant le numero specifi e.
  • Page 152 KDL-26S3000/32S3000/40S3000/46S3000 NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les remplacer mark are critical for safety. Replace only que par une piece portant le numero specifi e.
  • Page 153 S29AL016D70TFI010-WAX3A4U J1700 1-821-026-11 OPTICAL OUT TERMINAL (KDL-26S3000 ONLY) J1701 1-820-765-11 PHONO JACK IC3002 6-807-481-03 S29AL016D70TFI010-WAX3A2 J1710 1-820-638-11 JACK (SMALL TYPE) (ALL EXCEPT KDL-26S3000 ONLY) IC3004 6-703-175-01 PST3629UL J5000 1-821-013-11 D SUB CONNECTOR IC3005 6-710-121-01 M24256-BWMN6TP(A) J5502 1-818-737-11 HDMI CONNECTOR IC3006...
  • Page 154 KDL-26S3000/32S3000/40S3000/46S3000 NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les remplacer mark are critical for safety. Replace only que par une piece portant le numero specifi e.
  • Page 155 KDL-26S3000/32S3000/40S3000/46S3000 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES Q7801 8-729-620-13 TRANSISTOR 2SC4154TP-1EF R1111 1-218-831-11 METAL CHIP 0.50% 1/10W Q7802 6-551-699-01 TRANSISTOR ISA1602AM1TP-1EF R1112 1-218-831-11 METAL CHIP 0.50% 1/10W R1113 1-218-933-11 RES-CHIP 1/16W Q7803 8-729-620-07 TRANSISTOR...
  • Page 156 KDL-26S3000/32S3000/40S3000/46S3000 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES R2026 1-218-937-11 RES-CHIP 1/16W R2122 1-208-715-11 METAL CHIP 0.50% 1/16W R2033 1-218-941-81 RES-CHIP 1/16W R2126 1-208-927-11 METAL CHIP 0.50% 1/16W R2129 1-208-715-11 METAL CHIP 0.50% 1/16W R2035...
  • Page 157 KDL-26S3000/32S3000/40S3000/46S3000 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES R2207 1-218-937-11 RES-CHIP 1/16W R3052 1-218-941-81 RES-CHIP 1/16W R2210 1-208-703-11 METAL CHIP 6.8K 0.50% 1/16W R3053 1-218-990-81 SHORT CHIP R3055 1-218-973-11 RES-CHIP 1/16W R2211 1-208-703-11 METAL CHIP 6.8K...
  • Page 158 KDL-26S3000/32S3000/40S3000/46S3000 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES R3258 1-400-591-22 FERRITE 0μH R4512 1-218-990-81 SHORT CHIP R3259 1-400-591-22 FERRITE 0μH R4516 1-218-941-81 RES-CHIP 1/16W R4521 1-218-937-11 RES-CHIP 1/16W R3260 1-400-591-22 FERRITE 0μH R3261 1-400-591-22 FERRITE 0μH...
  • Page 159 KDL-26S3000/32S3000/40S3000/46S3000 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES R4917 1-218-933-11 RES-CHIP 1/16W R5563 1-218-929-11 RES-CHIP 1/16W R4918 1-218-933-11 RES-CHIP 1/16W R5564 1-218-929-11 RES-CHIP 1/16W R5565 1-218-929-11 RES-CHIP 1/16W R4919 1-218-933-11 RES-CHIP 1/16W R5000 1-216-864-11 SHORT CHIP...
  • Page 160 KDL-26S3000/32S3000/40S3000/46S3000 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES R7034 1-218-977-11 RES-CHIP 100K 1/16W R7084 1-216-864-11 SHORT CHIP R7035 1-208-695-11 METAL CHIP 3.3K 0.50% 1/16W R7085 1-216-864-11 SHORT CHIP R7087 1-216-864-11 SHORT CHIP R7036 1-218-982-11 RES-CHIP...
  • Page 161 KDL-26S3000/32S3000/40S3000/46S3000 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES R7404 1-208-683-11 METAL CHIP 0.50% 1/16W R7717 1-218-935-11 RES-CHIP 1/16W R7405 1-208-683-11 METAL CHIP 0.50% 1/16W R7718 1-218-953-11 RES-CHIP 1/16W R7720 1-218-941-81 RES-CHIP 1/16W R7406 1-208-683-11 METAL CHIP 0.50% 1/16W...
  • Page 162 KDL-26S3000/32S3000/40S3000/46S3000 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES R7969 1-208-928-11 METAL CHIP 0.50% 1/16W RB4503 1-234-370-21 RES, NETWORK 22 (1005X4) R7970 1-218-969-11 RES-CHIP 1/16W RB4504 1-234-370-21 RES, NETWORK 22 (1005X4) RB4505 1-234-370-21 RES, NETWORK 22...
  • Page 163 KDL-26S3000/32S3000/40S3000/46S3000 BU1 D1 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES RB7610 1-234-370-21 RES, NETWORK 22 (1005X4) VD5514 1-802-417-11 SURGE ABSORBER RB7611 1-234-370-21 RES, NETWORK 22 (1005X4) VD5515 1-802-417-11 SURGE ABSORBER VD5517 1-802-417-11 SURGE ABSORBER RB7612...
  • Page 164 KDL-26S3000/32S3000/40S3000/46S3000 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES C6710 1-162-967-11 CERAMIC CHIP 0.0033μF 10% C6753 1-107-906-11 ELECT 10μF (KDL-40S3000 ONLY) C6754 1-107-826-11 CERAMIC CHIP 0.1μF C6710 1-162-968-11 CERAMIC CHIP 0.0047μF 10% (KDL-46S3000 ONLY) C6755 1-162-964-11 CERAMIC CHIP 0.001μF 10%...
  • Page 165 KDL-26S3000/32S3000/40S3000/46S3000 NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les remplacer mark are critical for safety. Replace only que par une piece portant le numero specifi e.
  • Page 166 KDL-26S3000/32S3000/40S3000/46S3000 D1 D2 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES R6736 1-218-885-11 METAL CHIP 0.50% 1/10W R6805 1-216-793-11 METAL CHIP 1/10W R6737 1-216-821-11 METAL CHIP 1/10W R6806 1-216-864-11 SHORT CHIP R6739 1-216-864-11 SHORT CHIP R6750...
  • Page 167 SHORT CHIP JR6902 1-216-296-11 SHORT CHIP 1-474-056-11 G1D BOARD, COMPLETE (POWER SUPPLY) JR6903 1-216-296-11 SHORT CHIP (KDL-26S3000 ONLY) This board is manufactured by a 3rd party. COIL Component level repair information is not available. L6900 1-406-977-21 INDUCTOR 100μH TRANSISTOR Q6902...
  • Page 168 KDL-26S3000/32S3000/40S3000/46S3000 NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les remplacer mark are critical for safety. Replace only que par une piece portant le numero specifi e.
  • Page 169 KDL-26S3000/32S3000/40S3000/46S3000 NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les remplacer mark are critical for safety. Replace only que par une piece portant le numero specifi e.
  • Page 170 KDL-26S3000/32S3000/40S3000/46S3000 NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les remplacer mark are critical for safety. Replace only que par une piece portant le numero specifi e.
  • Page 171 KDL-26S3000/32S3000/40S3000/46S3000 NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les remplacer mark are critical for safety. Replace only que par une piece portant le numero specifi e.
  • Page 172 KDL-26S3000/32S3000/40S3000/46S3000 H1 H3 H4 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES TRANSISTOR Q301 8-729-028-96 TRANSISTOR DTC114EUA-T106 Q302 8-729-028-96 TRANSISTOR DTC114EUA-T106 Q303 8-729-028-96 TRANSISTOR DTC114EUA-T106 A-1220-318-A H1 BOARD, MOUNTED Q304 8-729-028-96 TRANSISTOR DTC114EUA-T106 Q305 8-729-028-96 TRANSISTOR...
  • Page 173 1-804-988-21 VARISTOR, CHIP (1608) CN201 1-819-928-11 HEADER ASSEMBLY ACCESSORIES AND PACKING CN202 1-695-915-11 TAB (CONTACT) 1-831-499-21 POWER-SUPPLY CORD SET DIODE (KDL-26S3000/32S3000 ONLY) 1-832-937-11 AC POWER-SUPPLY CORD SET D203 8-719-423-03 DIODE MA8100 (KDL-40S3000/46S3000 ONLY) D204 8-719-423-03 DIODE MA8100 X-2102-511-2 BAG ASSY, RUDDER LOCK...
  • Page 174 CLAMP REMOTE COMMANDER 1-500-915-11 CLAMP FILTER (FERRITE, CORE) 1-480-262-11 REMOTE COMMANDER (RM-YD018) (KDL-40S3000/46S3000 ONLY) 9-885-110-88 COVER, BATTERY (RM-YD018) 2-319-961-02 CUSHION, LOWER (KDL-26S3000/32S3000 ONLY) 2-319-966-02 CUSHION, LOWER (KDL-40S3000 ONLY) 3-093-196-02 CUSHION, LOWER (KDL-46S3000 ONLY) 3-211-990-01 CUSHION, LOWER (KDL-46S3000 ONLY) 2-319-960-01 CUSHION, UPPER...

  • Page 175: Appendix A: Encryption Key Components

    MUST BE RETURNED to Sony. b) and if the core charge is NOT covered under the product warranty, the defective un-repaired or modifi...
  • Page 176 In an effort to reduce the size of this pdf fi le the tiled schematics are not attached to this Service Manual. To receive a complete set of the tiled schematics for this manual please submit a request to the Service Promotion Department at [email protected].

This manual is also suitable for:

Kdl-32s3000Kdl-46s3000Kdl-40s3000

Table of Contents