SPECIFICATIONS KV-21FE12 KV-21FE12A KV- 21FE12C KV-21FM12 KV-20FS12 KV-20FV12 KV-21FV12 KV-21FV12C Power requirements 120-220V, 50/60 Hz 120-220V, 50/60 Hz 120V,60Hz 120V,60Hz 120-220V, 50/60 Hz 120-220V, 50/60 Hz Number of inputs/outputs Video 1) S Video 2) Audio 3) Audio Out 4) Speaker output(W) 5W x 2 3W x 2 3W x 2...
SECURITE DU FONCTIONNEMENT. NE LES REMPLACER QUE PAR DES SONY PARTS WHOSE PART NUMBERS APPEAR AS COMPOSANTS SONY DONT LE NUMERO DE PIECE EST INDIQUE DANS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS LE PRESENT MANUEL OU DANS DES SUPPLEMENTS PUBLIES PAR SONY.
Page 5
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C Display of Standby/Timer LED Flash Count 2 times 4 times 5 times LED ON 0.3 sec. STANDBY/TIMER LED LED OFF LED OFF 0.3 sec. 3 sec. Diagnostic Item Flash Count* +B overcurrent 2 times Vertical deflection stopped 4 times White balance failure 5 times *One flash count is not used for self-diagnostic.
Page 6
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C Handling of Self-Diagnostic Screen Display Since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic screen during repairs. When you have completed the repairs, clear the result display to “0”. Unless the result display is cleared to “0”, the self-diagnostic function will not be able to detect subsequent faults after completion of the repairs.
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C SAFETY CHECK-OUT After correcting the original service problem, perform the Leakage Test following safety checks before releasing the set to the The AC leakage from any exposed metal part to earth customer: ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 1.
SECTION 1 GENERAL The instructions mentioned here are partial abstracts from the Operating Instruction Manual. Operating Instructions The page numbers shown reflect those of the Operating Instruction Manual. Connecting Additional Equipment Connecting Your TV TV and VCR Rear of TV Read this section before setting up your TV for the first time.
Page 9
Connecting Your TV Operating Instructions TV and Cable Box TV, VCR, and Cable box Cable Box Rear of TV Coaxial Cable From cable Coaxial Cable Rear of TV Cable box Coaxial (Optional connection) Cable From cable Connect the coaxial cable from your cable service to the IN jack on your cable box.
Page 10
Connecting Your TV Operating Instructions TV and Satellite Receiver TV, Satellite Receiver, and VCR Satellite Rear of TV antenna From cable Rear of TV cable/ From antenna cable/ antenna Satellite receiver SATELLITE IN VHF/UHF AUDIO R A UDIO L VIDEO AUDIO R A UDIO L VIDEO SATELLITE IN VHF/UHF...
Using the Remote Control and Operating Instructions Basic Functions MENU Displays the on-screen menu. Press again to exit the menu at This section shows you how to use the more advanced buttons on the any time. remote control and how to use the on-screen menus. Press to return to factory settings RESET while in an on-screen menu.
If you are having a problem with your TV, try the suggestions below. If don’t seem to under Setup (page 23). the problem persists, contact your nearest Sony dealer. work Perform Auto Program to add channels that are not No picture, no Make sure the power cord is plugged in.
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C 2-4. PICTURE TUBE REMOVAL WARNING: BEFORE REMOVING THE ANODE CAP High voltage remains in the CRT even after the power is disconnected. To avoid electric shock, discharge CRT before attempting to remove the anode cap. Short between anode and CRT coated earth ground strap.
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C SECTION 3 SET-UP ADJUSTMENTS The following adjustments should be made when Perform the adjustments in order as follows: 1. Beam Landing a complete realignment is required or when a new 2. Convergence picture tube is installed. 3. Focus These adjustments should be performed with rated 4.
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C 3-2. CONVERGENCE Horizontal Static Convergence Before starting convergence adjustments: If the blue dot does not converge with the red and green dots, perform the following: 1. Perform FOCUS, V.LIN AND V.SIZE adjustments. 1. Move BMC magnet (a) to correct insufficient H. Static 2.
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C 6. Adjust vertical red and blue convergence with V.TILT (TLV VR). Perform adjustments while tracking items 1 and 2. B G R R G B Screen-Corner Convergence R G B B G R 1. Affix a permalloy assembly corresponding to the misconverged areas.
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C 3-5. METHOD OF SETTING THE SERVICE ADJUSTMENT MODE Service Mode Procedure 1. Standby mode (power off). Channel 5 Display Sound volume Power on the Remote Commander (press each button within a second). Service Adjustment Mode In 1. The CRT displays the item being adjusted. Disp.
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C SECTION 4 SAFETY RELATED ADJUSTMENTS 4-1. R562 CONFIRMATION METHOD Hold-Down Readjustment (HV HOLD-DOWN CONFIRMATION) AND If the setting indicated in step 2 of Hold-Down Operation READJUSTMENTS Confirmation cannot be met, readjustment should be performed by altering the resistance value of R562 component marked with The following adjustments should always be performed when replacing the following components which are marked with T505...
Page 20
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C DIGITAL POWER MULTIMETER SUPPLY – – 1SS119 R562 C546 T505 ABL11 AMMETER 3mA dc range – Figure 1 — 20 —...
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C SECTION 5 CIRCUIT ADJUSTMENTS ELECTRICAL ADJUSTMENTS BY REMOTE COMMANDER Use the Remote Commander (RM-Y168, RM-Y172 or RM-Y173) to perform the circuit adjustments in this section. NOTE: Test Equipment Required: • Pattern generator • Frequency counter • Digital multimeter • Audio oscillator 5-1.
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C Adjustment Items AVERAGE Reg # ITEM FUNCTION RANGE DATA NTSC PAL M PAL N VIDEO DATA HSIZ Horizontal Size Adjustment 0-63 HPOS Horizontal Position Adjustment 0-63 VBOW Vertical Line Bowing Adj. 0-15 VANG Vertical line Bowing Slant Adj. 0-15 TRAP Horizontal Trapezoid Adj.
Page 23
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C AVERAGE Reg # ITEM FUNCTION RANGE DATA NTSC PAL M PAL N VIDEO DATA Vertical Sync Slice Level Horizontal Sync Slice Level HMSK VTMS Select Signal VTIM Pin CDMD Vertical Count Down Mode Switching AFC Loop Gain Switching FIFR Field Frequency SBAL Sub Balance...
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C 5-4. MB BOARD ADJUSTMENTS 11. Reset Picture and Color to normal values: PICTURE: MAX COLOR: CENTER H. Frequency (Free Run) Check 12. Press then to save into the memory. 1. Input a TV mode (RF) with no signal. 2. Connect a frequency counter to base of Q501 Display Position Adjustment (DISP) (TP-500 H.
Page 25
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C 9. Select the DCOL item and reset to 1. H. Size Adjustment (HSIZ) 10. Press then to save into the memory. 1. Input a monoscope signal. 2. Activate the Service Adjustment Mode. 3. Select HSIZ with V. Size Adjustment (VSIZ) 4.
Page 26
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C V. Angle (VANG), V. Bow (VBOW), Upper pin (UPIN) and Low Pin (LPIN) Adjustments 1. Input a crosshatch signal. 2. Activate the Service Adjustment Mode. 3. Select VANG, VBOW, UPIN, and LPIN with 4. Adjust with for the best picture. 5.
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C [POWER SUPPLY, DEFLECTION, TUNER/IF, AUDIO, MTS] K BOARD SCHEMATIC DIAGRAM (KV-20FV12/21FV12/21FV12C ONLY) A BOARD IC VOLTAGE LIST IC401 IC406 IC501 13.3 TU101 volt 14.1 volt volt IC601 IC604 volt volt volt -31.8 13.3 30.7 -2.5 -32.7 14.3 53.2 -23.8 IC2001 10.1 -32.7...
REF. NO. PART NO. DESCRIPTION REMARK X-4037-400-1 BEZNET ASSY * A-1304-183-A MB (VAR) MOUNTED PC BOARD 4-046-161-01 EMBLEM (NO.8), SONY * A-1299-174-A A COMPLETE PC BOARD 4-073-931-01 BUTTON, MULTI The high-voltage leads associated with the FBT on this board 4-073-933-01 GUIDE, LED are not included and must be ordered separately.
X-4037-392-1 BEZNET ASSY * A-1304-183-A MB (VAR) MOUNTED PC BOARD (KV-20FS12 ONLY) (KV-20FS12 ONLY) 4-046-161-01 EMBLEM (NO.8), SONY A-1299-182-A A COMPLETE PC BOARD** (KV-20FS12 ONLY) 4-073-931-11 BUTTON, MULTI (KV-21FM12 ONLY) * A-1299-189-A A COMPLETE PC BOARD** (KV-21FM12 ONLY) 4-073-843-01 BUTTON, MULTI (KV-20FS12 ONLY) **The high-voltage leads associated with the FBT on this board are not included and must be ordered separately.
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C SECTION 8 ELECTRICAL PARTS LIST Note: • The components identified by in this manual have been carefully factory- selected for each set in order to satisfy The components identified by shading regulations regarding X-ray radiation. and mark are critical for safety. Replace Should replacement be required, replace only with part number specified.
Page 39
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. Replace sont critiques pour la securite. Ne les remplacer only with part number specified. que par une piece portant le numero specifie. REF.NO.
Page 40
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. Replace sont critiques pour la securite. Ne les remplacer only with part number specified. que par une piece portant le numero specifie. REF.NO.
Page 41
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. Replace sont critiques pour la securite. Ne les remplacer only with part number specified. que par une piece portant le numero specifie. REF.NO.
Page 42
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. Replace sont critiques pour la securite. Ne les remplacer only with part number specified. que par une piece portant le numero specifie. REF.NO.
Page 43
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C Note: Note: The components identified by in this manual have been The components identified by shading carefully factory-selected for each set in order to satisfy and mark are critical for safety. regulations regarding x-ray radiation. Should replacement Replace only with part number specified. be required, replace only with the value originally used.
Page 44
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. Replace sont critiques pour la securite. Ne les remplacer only with part number specified. que par une piece portant le numero specifie. REF.NO.
Page 45
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. Replace sont critiques pour la securite. Ne les remplacer only with part number specified. que par une piece portant le numero specifie. REF.NO.
Page 46
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. Replace sont critiques pour la securite. Ne les remplacer only with part number specified. que par une piece portant le numero specifie. REF.NO.
Page 47
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. Replace sont critiques pour la securite. Ne les remplacer only with part number specified. que par une piece portant le numero specifie. REF.NO.
Page 48
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. Replace sont critiques pour la securite. Ne les remplacer only with part number specified. que par une piece portant le numero specifie. REF.NO.
Page 49
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. Replace sont critiques pour la securite. Ne les remplacer only with part number specified. que par une piece portant le numero specifie. REF.NO.
Page 50
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. Replace sont critiques pour la securite. Ne les remplacer only with part number specified. que par une piece portant le numero specifie. REF.NO.
Page 51
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. Replace sont critiques pour la securite. Ne les remplacer only with part number specified. que par une piece portant le numero specifie. REF.NO.
Page 52
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. Replace sont critiques pour la securite. Ne les remplacer only with part number specified. que par une piece portant le numero specifie. REF.NO.
Page 54
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C Sony Corporation English Sony Technology Center 2000AS74350-1 Product Quality Division Printed in USA 9-965-879-01 Service Promotion Dept. 2000.2 — 72 —...
Page 55
BA-5 SERVICE MANUAL CHASSIS MODEL DEST COMMANDER CHASSIS NO. KV-20FS12 RM-Y173 SCC-S40A-A KV-20FS12 RM-Y173 SCC-S41A-A KV-20FV12 RM-Y168 SCC-S40B-A KV-20FV12 RM-Y168 SCC-S41B-A KV-21FE12 RM-Y173 SCC-S38A-A KV-21FE12A RM-Y173 SCC-S38F-A KV-21FE12C RM-Y173 SCC-S38B-A KV-21FM12 RM-Y172 SCC-S39A-A KV-21FV12 RM-Y168 SCC-S38C-A KV-21FV12C RM-Y168 SCC-S38D-A CORRECTION- 1 SUBJECT: BLOCK DIAGRAM, A BOARD VOLTAGE TABLE, PARTS LIST (All Variant Parts Identified)
Page 57
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C SECTION 6 A BOARD IC VOLTAGE TABLES (Page 37) : Corrected item A BOARD IC VOLTAGE LIST IC401 IC501 IC602 TU101 volt volt volt volt 135.9 123.4 30.7 14.1 14.3 IC603 volt 10.1 13.3 IC405 volt 14.0 13.3 IC502 volt IC604 volt...
Page 58
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C SECTION 8 ELECTRICAL PARTS LIST Note: • The components identified by in this manual have been carefully factory- selected for each set in order to satisfy The components identified by shading regulations regarding X-ray radiation. and mark are critical for safety. Replace Should replacement be required, replace only with part number specified.
Page 59
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. Replace sont critiques pour la securite. Ne les remplacer only with part number specified. que par une piece portant le numero specifie. REF.NO.
Page 60
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. Replace sont critiques pour la securite. Ne les remplacer only with part number specified. que par une piece portant le numero specifie. REF.NO.
Page 61
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. Replace sont critiques pour la securite. Ne les remplacer only with part number specified. que par une piece portant le numero specifie. REF.NO.
Page 62
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. Replace sont critiques pour la securite. Ne les remplacer only with part number specified. que par une piece portant le numero specifie. REF.NO.
Page 63
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C Note: Note: The components identified by in this manual have been The components identified by shading carefully factory-selected for each set in order to satisfy and mark are critical for safety. regulations regarding x-ray radiation. Should replacement Replace only with part number specified. be required, replace only with the value originally used.
Page 64
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. Replace sont critiques pour la securite. Ne les remplacer only with part number specified. que par une piece portant le numero specifie. REF.NO.
Page 65
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. Replace sont critiques pour la securite. Ne les remplacer only with part number specified. que par une piece portant le numero specifie. REF.NO.
Page 66
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. Replace sont critiques pour la securite. Ne les remplacer only with part number specified. que par une piece portant le numero specifie. REF.NO.
Page 67
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. Replace sont critiques pour la securite. Ne les remplacer only with part number specified. que par une piece portant le numero specifie. REF.NO.
Page 68
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. Replace sont critiques pour la securite. Ne les remplacer only with part number specified. que par une piece portant le numero specifie. REF.NO.
Page 69
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. Replace sont critiques pour la securite. Ne les remplacer only with part number specified. que par une piece portant le numero specifie. REF.NO.
Page 70
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. Replace sont critiques pour la securite. Ne les remplacer only with part number specified. que par une piece portant le numero specifie. REF.NO.
Page 71
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. Replace sont critiques pour la securite. Ne les remplacer only with part number specified. que par une piece portant le numero specifie. REF.NO.
Page 72
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. Replace sont critiques pour la securite. Ne les remplacer only with part number specified. que par une piece portant le numero specifie. REF.NO.
Page 74
KV-20FS12/20FV12/21FE12/A/C/21FM12/21FV12/C Sony Corporation English Sony Technology Center 2000AS74325-1 Product Quality Division Printed in USA 9-965-879-91 Service Promotion Dept. 2000.3 — 20 —...