Related Manuals for Fujitsu D2779
Summary of Contents for Fujitsu D2779
- Page 1 Technical Manual - English System Board D2779 for PRIMERGY TX100 S2 Technical Manual Edition June 2010...
- Page 2 – The contents of this manual may be revised without prior notice. – Fujitsu assumes no liability for damages to third party copyrights or other rights arising from the use of any information in this manual. – No part of this manual may be reproduced in any form without the prior written permission of Fujitsu.
- Page 3 It has not been designed or manufactured for uses which demand an extremely high level of safety and carry a direct and serious risk to life or body if such safety cannot be ensured. Technical Manual D2779 (TX100 S2)
- Page 4 (hereafter, "high safety use"). Customers should not use this product for high safety use unless measures are in place for ensuring the level of safety demanded of such use. Please consult the sales staff of Fujitsu if intending to use this product for high safety use.
- Page 5 Only for the Japanese market: Although described in this manual, some sections do not apply to the Japanese market. These options and routines include: – USB Flash Module (UFM) – Replacing the lithium battery Technical Manual D2779 (TX100 S2)
- Page 6 Technical Manual D2779 (TX100 S2)
-
Page 7: Table Of Contents
External connectors ..... . . 30 Replacing the lithium battery ....31 Technical Manual D2779 (TX100 S2) - Page 8 Contents Technical Manual D2779 (TX100 S2)
-
Page 9: Introduction
DVDs (see Installation DVD of ServerView Suite - ServerView Software Products). You will find further information about the BIOS setup in the "D2779 BIOS Setup Utility for TX100 S2" manual. PRIMERGY manuals are available in PDF format on the ServerView Suite DVD 2. - Page 10 Notational conventions Introduction Technical Manual D2779 (TX100 S2)
-
Page 11: Important Information
Information on which system expansions are approved for installation can be obtained from our customer service center or your sales outlet. The warranty expires if the device is damaged during the installation or replacement of system expansions. Technical Manual D2779 (TX100 S2) - Page 12 This information does not apply to the Japanese market. It is essential to observe the instructions in the chapter "Replacing the lithium battery". Technical Manual D2779 (TX100 S2)
- Page 13 Do not touch any connectors or conduction paths on an ESD. Place all the components on a pad which is free of electrostatic charge. For a detailed description of how to handle ESD components, see the relevant European or international standards (EN 61340-5-1, ANSI/ESD S20.20). Technical Manual D2779 (TX100 S2)
-
Page 14: Ce Certificate Of Conformity
The board complies with the requirements of the EC directives 2004/108/EC regarding “Electromagnetic Compatibility” and 2006/95/EC “Low Voltage Directive”. This is indicated by the CE marking (CE = Communauté Européenne). Compliance was tested in a typical PRIMERGY configuration. Technical Manual D2779 (TX100 S2) -
Page 15: Environmental Protection
Environmental protection Environmental protection Environmentally-friendly product design and development This product has been designed in accordance with the Fujitsu standard for "environmentally friendly product design and development". This means that key factors such as durability, selection and labeling of materials, emissions, packaging, ease of dismantling and recycling have been taken into account. - Page 16 Details regarding the return and recycling of devices and consumables within Europe can also be found in the "Returning used devices" manual, via your local Fujitsu branch or from our recycling center in Paderborn: Fujitsu Technology Solutions Recycling Center D-33106 Paderborn Tel.
-
Page 17: Features
– Trusted Platform Module (TPM) (Option) – 1x USB Flash Module (UFM) (Option) External connectors – 8x USB 2.0 connector (2 front, 6 rear) – 1x serial (COM1) port – 1x VGA – 1x RJ45 LAN connector Technical Manual D2779 (TX100 S2) - Page 18 – Battery on socket for recycling – RoHS compliant (1.1.2006) Power management – ACPI (states S0, S4, S5) – ACPI 2.0 – 3.3 V auxiliary power on the PCI/PCIe bus slots – On/Off/Sleep/Wake by power button – On/Off software Technical Manual D2779 (TX100 S2)
- Page 19 TPM or the system board is faulty you will not be able to access your data. – If a failure occurs, please inform your service about the TPM activation before it takes any action, and be prepared to provide them with your backup copies of the TPM content. Technical Manual D2779 (TX100 S2)
-
Page 20: Main Memory
– Each memory bank is equipped with two memory modules with the same capacity. – The module capacity between pairs can differ: pair 1A/1B can be populated with two 1 GB modules and pair 2A/2B with two 2 GB modules. Technical Manual D2779 (TX100 S2) -
Page 21: Fitting Rules
DIMM 1A and DIMM 2A (e.g. DIMM 1A = 1GB, DIMM 2A = 1GB, DIMM 1B = 2GB). Configuration 3 and 4: For dual-channel configuration arrange identical memory modules in pairs of the sockets. Technical Manual D2779 (TX100 S2) - Page 22 Main memory Features Install identical memory modules in sockets DIMM 1A and DIMM 1B and identical memory modules in sockets DIMM 2A and DIMM 2B. Technical Manual D2779 (TX100 S2)
-
Page 23: Pci / Pcie Slots
Features PCI / PCIe slots PCI / PCIe slots Figure 3: PCIe slots on system board D2779 Pos. PCIe slot Description Hot-plug Slot 1 PCI 3.0 slot (32 Bit / 33MHz) (support for 3.3V and 3.3V/5V cards) Slot 2 PCI Express slot (Gen 2), x8 connector... -
Page 24: Screen Resolutions
The BMC supports two fan interfaces. Fan control The fans are controlled according to temperature. Maximum speed will only be achieved when switching on the server and in case of a fan test. Technical Manual D2779 (TX100 S2) - Page 25 System events only will be logged during OS runtime. All monitored events of the system board are signalized and recorded in the System Event Log. They could be retrieved in the BIOS Setup or via the ServerView Operations Manager. Technical Manual D2779 (TX100 S2)
-
Page 26: Connectors And Jumpers
Connectors and jumpers Features Connectors and jumpers 3.6.1 Onboard connectors Figure 4: Connectors on system board D2779 Pos. Connector Pos. Connector PCI / PCIe slots PC2009 HDD activity (SCSI / SAS) Front panel Power connector 1 Power connector 2 Fan 1... - Page 27 Parallel port USB connectors 9 - 10 UFM connector Serial port Fan 3 USB 1 - 2 USB 3 - 4 USB 11 - 12 LAN / USB 5 - 6 USB stick Lithium battery Technical Manual D2779 (TX100 S2)
-
Page 28: Onboard Jumpers
Features 3.6.2 Onboard jumpers Pin 2 Pin 1 Pin 16 Figure 5: Position of the frontpanel connector on system board D2779 Pos. Description Front panel connector Settings of Jumper "Password Disable/Clear" (J5C3) Pin 16 Password Skip disabled (Default) Pin 16... - Page 29 Features Connectors and jumpers Settings of Jumper "BIOS Recovery" (J6D1) Pin 16 BIOS Recovery disabled (Default) Pin 16 BIOS Recovery enabled Technical Manual D2779 (TX100 S2)
-
Page 30: External Connectors
Connectors and jumpers Features 3.6.3 External connectors Figure 6: External connectors on system board D2779 Pos. Indicator Gigabit LAN USB 5 - 6 USB 3 - 4 USB 1 - 2 VGA port Serial port Technical Manual D2779 (TX100 S2) -
Page 31: Replacing The Lithium Battery
Ê Insert a new lithium battery of the same type into the socket (3) and (4). After replacing the battery date and time have to be set again. BIOS settings are set to default values. Technical Manual D2779 (TX100 S2) - Page 32 Replacing the lithium battery Technical Manual D2779 (TX100 S2)