Yamaha BANSHEE Owner's Manual
  1. Manuals
  2. Brands
  3. Yamaha Manuals
  4. Offroad Vehicle
  5. BANSHEE
  6. Owner's manual
Yamaha BANSHEE Owner's Manual

Yamaha BANSHEE Owner's Manual

Hide thumbs Also See for BANSHEE:
Table of Contents

Quick Links

READ THIS MANUAL CAREFULLY!
It contains important safety information.
OWNER'S MANUAL
YFZ350T
w
This ATV should not be ridden by anyone under 16 years of age.
LIT-11626-18-04
5FK-28199-17
Table of Contents
loading

Related Manuals for Yamaha BANSHEE

Summary of Contents for Yamaha BANSHEE

  • Page 1 READ THIS MANUAL CAREFULLY! It contains important safety information. OWNER’S MANUAL YFZ350T This ATV should not be ridden by anyone under 16 years of age. LIT-11626-18-04 5FK-28199-17...
  • Page 3 Yamaha experience in the production of fine sporting, touring, and pacesetting racing machines. With the purchase of this Yamaha, you can now appreciate the high degree of crafts- manship and reliability that have made Yamaha a leader in these fields.

  • Page 4: Important Manual Information

    EBU00801 IMPORTANT MANUAL INFORMATION FAILURE TO FOLLOW THE WARNINGS CONTAINED IN THIS MANUAL CAN RESULT IN SERIOUS INJURY OR DEATH. Particularly important information is distinguished in this manual by the following notations: The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Failure to follow WARNING instructions could result in severe injury or death to the machine operator, a bystander or a person inspecting or repairing the...

  • Page 5: Important Notice

    Please check your local riding laws and regulations before operating this ATV. EBU13330 YFZ350T OWNER’S MANUAL © 2004 by Yamaha Motor Corporation, AFFIX DEALER U.S.A. LABEL HERE 1st edition, March 2004 All rights reserved.

  • Page 6: Table Of Contents

    EBU00014 Indicates a potential hazard that could result in serious injury or death. CONTENTS LOCATION OF THE WARNING AND CONTROL FUNCTIONS ......4-1 SPECIFICATION LABELS....1-1 Main switch ........4-1 Handlebar switches ......4-2 Throttle lever ........4-3 Throttle OverRide System ....4-4 SAFETY INFORMATION......2-1 Speed limiter ........4-4 Clutch lever ........4-6 Front brake lever .......4-6 Brake pedal ........4-7...
  • Page 7 Seat ..........4-12 OPERATION .........6-1 Front shock absorber Starting a cold engine ......6-1 adjustment........4-13 Starting a warm engine .....6-3 Rear shock absorber Warming up ........6-3 adjustment........4-14 Shifting ..........6-4 To start out and accelerate ....6-5 To decelerate........6-6 PRE-OPERATION CHECKS ....5-1 Engine break-in .........6-7 Front and rear brakes......5-3 Parking ..........6-8 Fuel ...........5-5...
  • Page 8 Crossing a slope ......7-32 Brake fluid level check ....8-30 Crossing through shallow water ..7-34 Brake fluid replacement ....8-31 Riding over rough terrain....7-36 Front brake lever free play ....8-32 Sliding and skidding ......7-38 Brake pedal height adjustment..8-33 What to do if........7-40 Parking brake adjustment ....8-34 What to do...
  • Page 9 Tail/brake light bulb replacement..8-46 Troubleshooting.......8-47 Troubleshooting chart......8-48 No spark ..........8-51 CLEANING AND STORAGE ....9-1 A. Cleaning........9-1 B. Storage .........9-3 SPECIFICATIONS ......10-1 NOISE REGULATION......11-1 MAINTENANCE RECORD ....12-1 ATV LIMITED WARRANTY ....13-1...

  • Page 10: Location Of The Warning And Specification Labels

    Read and understand all of the labels on your machine. They contain important information for safe and proper operation of your ATV. Never remove any labels from your ATV. If a label becomes difficult to read or comes off, a replacement label is available from your Yamaha dealer.
  • Page 11 WARNING NEVER ride as a passenger. Passengers can cause a loss of control, resulting in SEVERE INJURY or DEATH. 5FE-2151H-01 5FE-2151H-40 5FK-21696-01 5FE-21568-01...
  • Page 12 5FE-21697-01...

  • Page 13: Safety Information

    EBU13381 SAFETY INFORMATION AN ATV IS NOT A TOY AND CAN BE HAZARDOUS TO OPERATE. An ATV handles differently from other vehicles including motorcycles and cars. A collision or rollover can occur quickly, even during routine maneuvers such as turning and riding on hills or over obstacles, if you fail to take proper precautions.
  • Page 14 8 Always avoid operating an ATV on any paved surfaces, including sidewalks, driveways, parking lots and streets. 8 Never operate an ATV on any public street, road or highway, even a dirt or gravel one. 8 Never operate an ATV without wearing an approved motorcycle helmet that fits properly. You should also wear eye protection (goggles or face shield), gloves, boots, a long-sleeved shirt or a jacket, and long pants.
  • Page 15 8 Never operate on excessively rough, slippery or loose terrain until you have learned and prac- ticed the skills necessary to control the ATV on such terrain. Always be especially cautious on these kinds of terrain. 8 Always follow proper procedures for turning as described in this manual. Practice turning at low speeds before attempting to turn at faster speeds.
  • Page 16 8 Always use proper procedures if you stall or roll backwards when climbing a hill. To avoid stalling, use the proper gear and maintain a steady speed when climbing a hill. If you stall or roll backwards, follow the special procedure for braking described in this manual. Dismount on the uphill side or to a side if pointed straight uphill.
  • Page 17 8 Never exceed the stated load capacity for an ATV. Cargo should be properly distributed and securely attached. Reduce speed and follow instructions in this manual for carrying cargo or pulling a trailer. Allow greater distance for braking. FOR MORE INFORMATION ABOUT ATV SAFETY, call the Consumer Products Safety Commission at 1-800-638-2772, or the ATV Distributor’s Safety Hotline at 1-800-852-5344.
  • Page 18 q WARNING When transporting the ATV in another vehicle, be sure it is kept upright and POTENTIAL HAZARD that the fuel cock is in the “OFF” posi- Improper handling of gasoline. tion. Otherwise, fuel may leak out of the WHAT CAN HAPPEN carburetor or fuel tank.
  • Page 19 q WARNING POTENTIAL HAZARD Starting or running the engine in a closed area. WHAT CAN HAPPEN Exhaust fumes are poisonous and may cause loss of consciousness and death within a short time. HOW TO AVOID THE HAZARD Always operate your ATV in an area with adequate ventilation.

  • Page 20: Description And Machine Identification

    EBU00032 DESCRIPTION AND MACHINE IDENTIFICATION !3 ! 4 1. Tail/brake light 12. Rear shock absorber 2. Seat 13. Spark arrester 3. Kick starter 14. Rear wheel 4. Fuel tank cap 15. Starter (choke) 5. Headlight 16. Shift pedal 6. Brake pedal 17.

  • Page 21: Identification Number Records

    This number can be used for ordering a new when ordering spare parts from a Yamaha key. dealer or for reference in case the vehicle is stolen.

  • Page 22: Vehicle Identification Number

    Record the information on this label in the space provided. This information NOTE: will be needed to order spare parts from your The vehicle identification number is used to Yamaha dealer. identify your machine. 1. Model label 1. Vehicle identification number...

  • Page 23: Control Functions

    EBU00039 CONTROL FUNCTIONS Indicates a potential hazard that could result in serious injury or death. EBU09420 Main switch Functions of the respective switch positions are as follows: The engine can be started only at this position and the headlights and taillight come on when the light switch is on.

  • Page 24: Handlebar Switches

    EBU00053 EBU13741 Handlebar switches Light switch “LIGHTS” Set the switch to the “LO” position to turn on the low beam and the taillight. Set the switch to the “HI” position to turn on the high beam and the taillight. Set the switch to the “OFF” position to turn off all the lights.

  • Page 25: Throttle Lever

    Check the operation of the throttle lever before you start the engine. If it does not work smoothly, check for the cause. Correct the problem before riding the 1. Throttle lever ATV. Consult a Yamaha dealer if you can’t find or solve the problem yourself.

  • Page 26: Throttle Override System

    2. Adjusting screw HOW TO AVOID THE HAZARD a. No more than 12 mm (0.47 in) Make sure that the cause of the malfunc- tion is corrected before restarting the engine. You should have the ATV inspected by a Yamaha dealer.
  • Page 27 q WARNING POTENTIAL HAZARD Improper adjustment of the speed limiter and throttle. WHAT CAN HAPPEN The throttle cable could be damaged. Improper throttle operation could result. You could lose control, have an accident or be injured. HOW TO AVOID THE HAZARD Do not turn the adjusting screw out more than 12 mm (0.47 in).

  • Page 28: Clutch Lever

    EBU00068 EBU09880 Clutch lever Brake lever The clutch lever is located on the left handle- The brake lever is located on the right handle- bar. bar. Pull it toward the handlebar to apply the Pull the clutch lever to the handlebar to disen- front brake.

  • Page 29: Brake Pedal

    EBU00989 EBU00080 Brake pedal Parking brake The brake pedal is located on the right side of Use the parking brake when you have to start the machine. Push down on the pedal to apply the engine or park the machine, especially on the rear brake.
  • Page 30 q WARNING POTENTIAL HAZARD Improper use of the parking brake. WHAT CAN HAPPEN The ATV could start moving unexpected- ly if the parking brake is not applied before starting the engine. This could cause loss of control or a collision. 1.

  • Page 31: Shift Pedal

    EBU00082 EBU00089 Shift pedal Kick starter This machine is equipped with a constant- Rotate the kick starter away from the engine. mesh 6-speed transmission. The shift pedal is Push the starter down lightly with your foot located on the left side of the engine and is until the gears engage, then kick smoothly used in combination with the clutch when and forcefully to start the engine.

  • Page 32: Fuel Tank Cap

    EBU00092 EBU00093 Fuel tank cap Fuel cock Remove the fuel tank cap by turning it coun- The fuel cock supplies fuel from the fuel tank terclockwise. to the carburetor. The fuel cock has three positions. OFF: With the lever in this position fuel will not flow.

  • Page 33: Starter (Choke)

    EBU00094 Starter (choke) Starting a cold engine requires a richer air-fuel mixture. A separate starter circuit supplies this mixture. Move in direction a to turn on the starter (choke). Move in direction b to turn off the starter (choke). Refer to “Starting a cold engine” for proper operation.

  • Page 34: Seat

    EBU00566 Seat To install the seat, insert the projection on the To remove the seat, pull the seat lock lever front of the seat into the seat holder and push upward and pull up the seat at the rear. down on the seat at the rear. NOTE: Make sure that the seat is securely fitted.

  • Page 35: Front Shock Absorber Adjustment

    The spring preload can be adjusted to suit the A special wrench can be obtained at a rider’s weight and riding conditions. Yamaha dealer to make this adjustment. Adjust the spring preload as follows. To increase the spring preload, turn the Standard position: C adjusting ring in direction a.

  • Page 36: Rear Shock Absorber Adjustment

    8 Do not dispose of a damaged or absorber can be adjusted to suit the rider’s worn out shock absorber yourself. weight and the riding conditions. Take the unit to a Yamaha dealer. q WARNING Adjust the spring preload as follows. POTENTIAL HAZARD 1.
  • Page 37 4. Tighten the locknut to the specified NOTE: A special wrench can be obtained at a torque. Yamaha dealer to make this adjustment. Tightening torque: 54 Nm (5.4 m0kgf, 39 ft0lbf) 3. The length of the spring (installed) changes 1.5 mm (0.06 in) per turn of the adjusting nut.
  • Page 38 Adjust the rebound damping force as follows. Adjust the compression damping force as fol- Turn the rebound damping force adjusting dial lows. in direction a to increase the rebound damp- Turn the compression damping force adjust- ing force and in direction b to decrease the ing knob in direction a to increase the com- pression damping force and in direction b to rebound damping force.

  • Page 39: Specifications

    q WARNING Never turn an adjusting mechanism POTENTIAL HAZARD beyond the minimum or maximum set- Suspension components become hot tings. during operation. WHAT CAN HAPPEN NOTE: You could be burned. Although the total number of clicks of a damp- HOW TO AVOID THE HAZARD ing force adjusting mechanism may not exact- Never touch the compression damping ly match the above specifications due to small...

  • Page 40: Pre-Operation Checks

    PRE-OPERATION CHECKS Before using this machine, check the following points: ITEM ROUTINE PAGE 9 Check operation, free play, fluid level and fluid leakage. 5-3–5-4 Brakes 9 Fill with DOT 4 brake fluid if necessary. 8-29–8-33 9 Check operation, condition and lever free play. Clutch 8-36 9 Check operation, condition and free play.
  • Page 41 q WARNING POTENTIAL HAZARD Failure to inspect the ATV before operat- ing. Failure to properly maintain the ATV. WHAT CAN HAPPEN Increases the possibility of an accident or equipment damage. HOW TO AVOID THE HAZARD Always inspect your ATV each time you use it to make sure the ATV is in safe operating condition.

  • Page 42: Front And Rear Brakes

    8 Check that there is no free play in the brake of the pipe joints or brake fluid reservoirs. lever. If there is free play, have a Yamaha Apply the brakes firmly for one minute. If there dealer inspect the brake system.
  • Page 43 Always check the brakes at the start of every ride. Do not ride the ATV if you find any problem with the brakes. If a problem cannot be corrected by the adjustment procedures provided in this manual, have a Yamaha dealer check for the cause.

  • Page 44: Fuel

    EBU13420 Fuel Your Yamaha engine has been designed to Make sure there is sufficient gasoline in the use premium unleaded gasoline with a pump tank. octane number ([R+M]/2) of 90 or higher, or research octane number of 95 or higher. If...

  • Page 45: Engine Mixing Oil

    EBU00132 q WARNING Engine mixing oil POTENTIAL HAZARD Recommended oil: Improper care when refueling. Yamalube “R” (Yamalube Racing 2-cycle oil) WHAT CAN HAPPEN Mixing ratio: 24:1 Fuel can spill, which can cause a fire and severe injury. If Yamalube “R” oil is not available, select an Fuel expands when it heats up.

  • Page 46: Transmission Oil

    8 In order to prevent clutch slippage back to the idle position when released. Have (since the transmission oil also lubri- a Yamaha dealer repair as necessary for cates the clutch), do not mix any chem- proper operation. ical additives. Do not use oils with a diesel specification of “CD”...

  • Page 47: Fittings And Fasteners

    EBU11620 Fittings and fasteners Always check the tightness of chassis fittings and fasteners before a ride. Take the machine to a Yamaha dealer or refer to the Service Manual for correct tightening torque. EBU10030 Lights Check the headlights and tail/brake light to make sure they are in working condition.

  • Page 48: Tires

    1. The tires listed below have been Rear 27 kPa (0.27 kgf/cm , 3.9 psi) approved by Yamaha Motor Co., Ltd. 4. Use no more than the following pres- for this model. Other tire combina- sures when seating the tire beads.

  • Page 49: How To Measure Tire Pressure

    EBU00159 How to measure tire pressure Set pressure with tires cold. Use the low-pressure tire gauge. Set tire pressures to the following specifica- tions: NOTE: Recommended Minimum Maximum The low-pressure tire gauge is included as pressure standard equipment. Make two measure- 30 kPa 27 kPa 33 kPa...

  • Page 50: Tire Wear Limit

    EBU00160 Tire wear limit When the tire groove decreases to 3 mm (0.12 in) due to wear, replace the tire. a. Tire wear limit 5-11...

  • Page 51: Operation

    2. Turn the fuel cock to “ON”. there is a control or function you do not 3. Turn the main switch to “ON” and the understand, ask your Yamaha dealer. engine stop switch to “RUN”. 4. Shift the transmission into neutral.
  • Page 52 Position 1: Cold engine start- 6. Completely close the throttle lever and ambient temperature below 5°C start the engine by kicking the kick starter. (40°F). 7. If the engine is started with the starter Position 2: Cold engine start- (choke) in position 1, the starter (choke) ambient temperature at 0°C should be returned to position 2 to warm (30°F)–30°C (90°F) and warming...

  • Page 53: Starting A Warm Engine

    EBU00180 EBU00538 Starting a warm engine Warming up To start a warm engine, refer to the “Starting a To get maximum engine life, always warm up cold engine” section. The starter (choke) the engine before starting off. Never acceler- should not be used. The throttle should be ate hard with a cold engine! To see whether or opened slightly.

  • Page 54: Shifting

    EBU01981 Shifting This model has a 6-speed forward transmis- 8 Do not coast for long periods with the sion. The transmission allows you to control engine off, and do not tow the machine a the amount of power you have available at a long distance.

  • Page 55: To Start Out And Accelerate

    EBU00203 To start out and accelerate 7. Open the throttle part way and gradually 1. Release the throttle lever. release the clutch lever. 8. Follow the same procedure when shifting to the next higher gear. Always close the throttle while shifting q WARNING gears.

  • Page 56: To Decelerate

    EBU00207 q WARNING To decelerate When slowing down or stopping, release the POTENTIAL HAZARD throttle and apply the brakes smoothly and Engaging a lower gear when the engine evenly. As you slow down, shift to a lower speed is too high. gear.

  • Page 57: Engine Break-In

    If any abnormality is noticed during this peri- od, consult a Yamaha dealer.

  • Page 58: Parking

    EBU00212 Parking When parking, stop the engine and shift into low gear. Turn the fuel cock to “OFF” and apply the parking brake. 1. Locked position...

  • Page 59: Parking On A Slope

    EBU11740 Parking on a slope 1. Bring the machine to a stop by applying the brakes in low gear. q WARNING 2. Stop the engine and release the clutch lever. POTENTIAL HAZARD 3. With the rear brake applied, apply the Parking on a hill or other incline.

  • Page 60: Accessories And Loading

    8 Choose only accessories designed for your dlebars which could make steering difficult, ATV. Your Yamaha dealer has a variety of an accessory that limits your ability to move genuine Yamaha accessories. Other acces- around on the seat, or one that limits your sories may also be available on the market.

  • Page 61: Loading

    EBU00584 8 Tie down cargo securely to the carriers. Loading As originally equipped, this ATV is not Make sure cargo in the trailer cannot move designed to carry cargo or tow a trailer. If you around. A shifting load can cause an acci- choose to add accessories so that you can dent.
  • Page 62 q WARNING POTENTIAL HAZARD Overloading this ATV or carrying or tow- ing cargo improperly. WHAT CAN HAPPEN Could cause changes in vehicle han- dling which could lead to an accident. HOW TO AVOID THE HAZARD Never exceed the stated load capacity for this ATV.

  • Page 63: Riding Your Atv

    Riding Your 1 7-1...

  • Page 64: Getting To Know Your Atv

    Indicates a potential hazard that could result in serious injury or death. GETTING TO KNOW YOUR ATV the operation of the controls. Pay particular This ATV is intended for recreational use by attention to the safety information on pages experienced operators only. 2-1–2-7.

  • Page 65: Ride With Care And Good Judgement

    MENT Beginning and inexperienced operators should complete the certified training Get training if you are inexperienced. course offered by Yamaha. They should Beginners should get training from a certified then regularly practice the skills learned instructor. in the course and the operating tech- Become familiar with this ATV at slow speeds niques described in this Owner ’s...
  • Page 66 Not recommended for children under 16 years of age. q WARNING POTENTIAL HAZARD Failure to follow the age recommenda- tions for this ATV. WHAT CAN HAPPEN Use by children of ATVs that are not rec- ommended for their age can lead to severe injury or death of the child.
  • Page 67 This ATV is designed to carry operator only - passengers prohibited. q WARNING POTENTIAL HAZARD Carrying a passenger on this ATV. WHAT CAN HAPPEN Greatly reduces your ability to balance and control this ATV. Could cause an accident, resulting in harm to you and/or your passenger.
  • Page 68 Apparel Operating without protective clothing q WARNING increases your chances of severe injury in the event of an accident. POTENTIAL HAZARD HOW TO AVOID THE HAZARD Operating this ATV without wearing an Always wear an approved motorcycle approved motorcycle helmet, eye pro- helmet that fits properly.
  • Page 69 Do not operate after consuming alcohol or q WARNING drugs. POTENTIAL HAZARD Operator’s performance capability is reduced by the influence of alcohol or drugs. Operating this ATV after consuming alcohol or drugs. WHAT CAN HAPPEN Could seriously affect your judgment. Could cause you to react more slowly.
  • Page 70 Pre-operation checks q WARNING Always perform the pre-operation checks list- POTENTIAL HAZARD ed on page 5-1 before riding for safety and proper care of the ATV. Operating this ATV with improper tires, or with improper or uneven tire pres- q WARNING sure.
  • Page 71 Speed limiter For riders inexperienced with this model, this Indicates a potential hazard that could model is equipped with a speed limiter in the result in serious injury or death. throttle lever housing. The speed limiter limits the power and top speed of the ATV. Turning Do not operate at speeds too fast for your the adjusting screw in decreases the top skills or the conditions.
  • Page 72 Loading and accessories q WARNING As originally equipped, this ATV is not POTENTIAL HAZARD designed to carry cargo or tow a trailer. If you choose to add accessories so that you can Overloading this ATV or carrying or tow- carry cargo or tow a trailer, you must use ing cargo improperly.
  • Page 73 During operation q WARNING Always keep your feet on the footboards dur- POTENTIAL HAZARD ing operation. Otherwise your feet may con- tact the rear wheels. Removing hands from handlebars or feet from footboards during operation. WHAT CAN HAPPEN Removing even one hand or foot can reduce your ability to control the ATV or could cause you to lose your balance and fall off of the ATV.
  • Page 74 Avoid wheelies and jumping. You may lose control of the ATV or overturn. q WARNING POTENTIAL HAZARD Attempting wheelies, jumps, and other stunts. WHAT CAN HAPPEN Increases the chance of an accident, including an overturn. HOW TO AVOID THE HAZARD Never attempt stunts, such as wheelies or jumps.
  • Page 75 Never modify this ATV through improper installation or use of accessories. All parts and accessories added to this vehicle should be genuine Yamaha or equivalent components designed for use on this ATV and should be installed and used according to instructions. If you have questions, consult an autho- rized ATV dealer.
  • Page 76 Exhaust system The exhaust system on the ATV is very hot HOW TO AVOID THE HAZARD during and following operation. To prevent Do not operate, idle, or park the ATV in burns, avoid touching the exhaust system. dry grass or other dry ground cover. Park the ATV in a place where pedestrians or Keep the engine area free of dry grass, children are not likely to touch it.

  • Page 77: Be Careful Where You Ride

    BE CAREFUL WHERE YOU RIDE This ATV is designed for off-road use only. Riding on paved surfaces can cause loss of control. q WARNING POTENTIAL HAZARD Operating this ATV on paved surfaces. WHAT CAN HAPPEN ATVs are designed for off-road use only. Paved surfaces may seriously affect handling and control of the ATV, and may cause the vehicle to go out of con-...
  • Page 78 Do not ride on any public road, street, or high- way. Riding on public roads can result in collisions with other vehicles. q WARNING POTENTIAL HAZARD Operating this ATV on public streets, roads or highways. WHAT CAN HAPPEN You can collide with another vehicle. HOW TO AVOID THE HAZARD Never operate this ATV on any public street, road or highway, even a dirt or...
  • Page 79 Know the terrain where you ride. Ride cau- tiously in unfamiliar areas. Stay alert for holes, rocks, or roots in the terrain, and other hidden hazards which may cause the ATV to upset. q WARNING POTENTIAL HAZARD Failure to use extra care when operating this ATV on unfamiliar terrain.
  • Page 80 q WARNING POTENTIAL HAZARD Failure to use extra care when operating on excessively rough, slippery or loose terrain. WHAT CAN HAPPEN Could cause loss of traction or vehicle control, which could result in an acci- dent, including an overturn. HOW TO AVOID THE HAZARD Do not operate on excessively rough, slippery or loose terrain until you have learned and practiced the skills neces-...
  • Page 81 When riding in an area where you might not WHAT CAN HAPPEN easily be seen, such as desert terrain, mount You could be in a collision. You could be a caution flag on the ATV. DO NOT use the injured. flag pole bracket as a trailer hitch.
  • Page 82 Select a large, flat area off-road to become With the engine idling, pull the clutch lever to familiar with your ATV. Make sure that this disengage the clutch and shift into 1st gear, area is free of obstacles and other riders. You and then release the parking brake.
  • Page 83 q WARNING evenly. As you slow down, shift to a lower gear. Be sure that the engine has sufficiently POTENTIAL HAZARD slowed before engaging a lower gear. Opening the throttle abruptly or releas- Improper use of the brakes or shifting can ing the clutch lever too quickly.

  • Page 84: Turning Your Atv

    TURNING YOUR ATV HOW TO AVOID THE HAZARD To achieve maximum traction while riding off- Always follow proper procedures for road, the two rear wheels are mounted solidly turning as described in this Owner’s on one axle and turn together at the same Manual.
  • Page 85 Once you have learned this technique you should be able to perform it at higher speeds Lean towards or in tighter curves. inside of turn. Support your weight on the outer footboard. Improper riding procedures such as abrupt throttle changes, excessive braking, incorrect body movements, or too much speed for the sharpness of the turn may cause the ATV to tip.

  • Page 86: Climbing Uphill

    CLIMBING UPHILL HOW TO AVOID THE HAZARD Use proper riding techniques to avoid vehicle Never operate the ATV on hills too steep overturns on hills. Be sure that you can for the ATV or for your abilities. maneuver your ATV well on flat ground before Practice on smaller hills before attempt- attempting any incline and then practice riding ing large hills.
  • Page 87 q WARNING Never go over the top of any hill at high speed. POTENTIAL HAZARD An obstacle, a sharp drop, or another Climbing hills improperly. vehicle or person could be on the other WHAT CAN HAPPEN side of the hill. Could cause loss of control or cause the ATV to overturn.
  • Page 88 If you are climbing a hill and you find that you When crossing the side of a hill: have not properly judged your ability to make it Always follow proper procedures as to the top, you should turn the ATV around while described in the Owner’s Manual.
  • Page 89 If your ATV has stalled or stopped and you q WARNING believe you can continue up the hill, restart POTENTIAL HAZARD carefully to make sure you do not lift the front Stalling, rolling backwards or improper- wheels which could cause you to lose control. ly dismounting while climbing a hill.
  • Page 90 When fully stopped, apply the rear brake as well, and then lock the park- ing brake. Dismount on uphill side or to a side if pointed straight uphill. Turn the ATV around and remount, following the pro- cedure described in the Owner ’s Manual.

  • Page 91: Riding Downhill

    RIDING DOWNHILL q WARNING When riding your ATV downhill, shift your POTENTIAL HAZARD weight as far to the rear and uphill side of the ATV as possible. Move back on the seat and Going down a hill improperly. sit with your arms straight. Choose a low gear WHAT CAN HAPPEN which will allow the engine compression to do Could cause loss of control or cause the...
  • Page 92 7-31...

  • Page 93: Crossing A Slope

    CROSSING A SLOPE q WARNING Traversing a sloping surface on your ATV POTENTIAL HAZARD requires you to properly position your weight to maintain proper balance. Be sure that you Improperly crossing hills or turning on have learned the basic riding skills on flat hills.
  • Page 94 Avoid hills with excessively slippery or loose surfaces. Shift your weight to the uphill side of the ATV. 7-33...

  • Page 95: Crossing Through Shallow Water

    CROSSING THROUGH SHALLOW WATER HOW TO AVOID THE HAZARD The ATV can be used to cross slow moving, Never operate this ATV in fast flowing shallow water of up to a maximum of 35 cm water or in water deeper than that speci- (14 inches) in depth.
  • Page 96 Test your brakes after leaving the water. Do not continue to ride your ATV without verifying After riding your ATV in water, be sure to that you have regained proper braking ability. drain the trapped water by removing the check hose at the bottom of the air filter case.

  • Page 97: Riding Over Rough Terrain

    RIDING OVER ROUGH TERRAIN q WARNING Riding over rough terrain should be done with POTENTIAL HAZARD caution. Look out for obstacles which could cause damage to the ATV or could lead to an Improperly operating over obstacles. upset or accident. Be sure to keep your feet WHAT CAN HAPPEN firmly mounted on the footboards at all times.

  • Page 98: Sliding And Skidding

    SLIDING AND SKIDDING If the rear wheels of your ATV start to slide Care should be used when riding on loose or sideways, control can usually be regained (if slippery surfaces since the ATV may slide. If there is room to do so) by steering in the unexpected and uncorrected, sliding could direction of the slide.
  • Page 99 With practice, over a period of time, skill at q WARNING controlled sliding can be developed. The ter- POTENTIAL HAZARD rain should be chosen carefully before Skidding or sliding improperly. attempting such maneuvers, since both stabil- ity and control are reduced. Bear in mind that WHAT CAN HAPPEN sliding maneuvers should always be avoided You may lose control of this ATV.

  • Page 100: What To Do If

    WHAT TO DO IF ... 8 If your ATV starts to slide sideways: This section is designed to be a reference Steer in the direction of the slide if you have guide only. Be sure to read each section on the room.
  • Page 101 8 If your ATV is traversing a sloping surface: Be sure to ride with your weight positioned towards the uphill side of the ATV to main- tain proper balance. If the ATV starts to tip, steer down the hill (if there are no obstacles in your way) to regain balance.

  • Page 102: Periodic Maintenance And Adjustment

    Turn off the engine when performing maintenance unless otherwise specified. Periodic inspection, adjustment and lubrica- Have a Yamaha dealer perform service if tion will keep your machine in the safest and you are not familiar with machine service. most efficient condition possible. Safety is an obligation of the machine owner.
  • Page 103 HOW TO AVOID THE HAZARD during a service operation requiring one, take Never modify this ATV through improper your machine to a Yamaha dealer to check the installation or use of accessories. All torque settings and adjust them as necessary.

  • Page 104: Periodic Maintenance/Lubrication

    EBU02611 PERIODIC MAINTENANCE/LUBRICATION NOTE: 8 For ATVs not equipped with an odometer or an hour meter, follow the month maintenance intervals. 8 For ATVs equipped with an odometer or an hour meter, follow the km (mi) or hours maintenance intervals. However, keep in mind that if the ATV isn’t used for a long period of time, the month maintenance intervals should be followed.
  • Page 105 9 Check routing and connection. *Throttle, control cable 9 Lubricate. Outside nuts and bolts 9 Retighten. 9 Clean and inspect. Frame 9 Inspect. Lighting equipment * Since these items require special tools, data and technical skills, have a Yamaha dealer perform the service.
  • Page 106 NOTE: 8 Recommended brake fluid: DOT 4 8 Brake fluid replacement: When disassembling the master cylinder or caliper cylinder, replace the brake fluid. Normally check the brake fluid level and add the fluid as required. On the inner parts of the master cylinder and caliper cylinder, replace the oil seals every two years.

  • Page 107: Transmission Oil

    EBU10981 Transmission oil NOTE: Transmission oil measurement Wait a few minutes until the oil level settles 1. Place the ATV on a level surface. before checking. 2. Warm up the engine for several minutes, and then stop it. 4. Remove the dipstick and check the oil 3.
  • Page 108 Recommended oil: See page 10-2. Oil quantity: Periodic oil change: 1.5 L (1.3 Imp qt, 1.6 US qt) 8 In order to prevent clutch slippage 1. Drain bolt (since the engine oil also lubricates the 5. Install the drain bolt, and then tighten it to clutch), do not mix any chemical addi- the specified torque.

  • Page 109: Cooling System

    7. Start the engine and warm up for a few minutes. While warming up, check for oil leakage. If oil leakage is found, stop the engine immediately, and check for the cause. 8. Turn the engine off, and then check the oil level and correct it if necessary.
  • Page 110 Hard water or salt water is harmful to the engine. You may use soft water if you can’t get distilled water. NOTE: 8 If water is added, have a Yamaha dealer check the antifreeze content of the coolant 1. Coolant reservoir cover as soon as possible.
  • Page 111 EBU00765 To change the coolant q WARNING POTENTIAL HAZARD Removing the radiator cap when the engine and radiator are still hot. WHAT CAN HAPPEN You could be burned by hot fluid and steam blown out under pressure. 1. Radiator cover 2.
  • Page 112 4. Remove the radiator cap. 6. Disconnect the hose on the coolant reser- voir side and drain the coolant from the coolant reservoir. 1. Radiator cap 5. Remove the coolant reservoir cap. 1. Coolant reservoir hose 2. Coolant reservoir 7. After draining the coolant, thoroughly flush the cooling system with clean tap water.
  • Page 113 1.5 L (1.3 Imp qt, 1.6 US qt) Coolant reservoir capacity: NOTE: 0.28 L (0.25 Imp qt, 0.30 US qt) If any leakage is found, ask a Yamaha dealer to inspect the cooling system. 15. Install the radiator cover by installing the bolts.

  • Page 114: Spark Plug Inspection

    Do not attempt to diagnose such problems your- self. Instead, take the machine to a Yamaha deal- er. You should periodically remove and inspect the spark plugs because heat and deposits will cause any spark plug to slowly break down and erode.

  • Page 115: Air Filter Element Cleaning

    When installing a spark plug, always clean the gasket surface and use a new gasket. Wipe off any grime from the threads and tighten to the specified torque. Tightening torque: Spark plug: 20 Nm (2.0 m0kgf, 14 ft0lbf) 1. Check hose EBU11334 Air filter element cleaning NOTE:...
  • Page 116 q WARNING POTENTIAL HAZARD Using low flash point solvents or gaso- line to clean the air filter element. WHAT CAN HAPPEN Low flash point solvents or gasoline can catch fire or explode. HOW TO AVOID THE HAZARD Use parts cleaning solvent to clean the air filter element.
  • Page 117 7. Apply Yamaha foam air filter oil or other NOTE: quality foam air filter oil to the air filter ele- The air filter element should be cleaned every ment. 20-40 hours. It should be cleaned and lubricated more often if the machine is operated in NOTE: extremely dusty areas.

  • Page 118: Spark Arrester Cleaning

    EBU13611 Spark arrester cleaning 2. Remove the tailpipe by pulling it out of the muffler. Be sure the exhaust pipe and muffler are cool before cleaning the spark arrester. 3. Tap the tailpipe lightly, and then use a 1. Remove the screws. wire brush to remove any carbon deposits from the spark arrester portion of the tailpipe.
  • Page 119 q WARNING POTENTIAL HAZARD Improper cleaning of the spark arrester. Hot exhaust system. WHAT CAN HAPPEN Could injure the eyes. Could cause burns. Could cause carbon monoxide poison- ing, possibly leading to death. Could start a fire. HOW TO AVOID THE HAZARD When cleaning the spark arrester: Always let the exhaust system cool prior to touching exhaust components.

  • Page 120: Carburetor Settings

    The carburetors could leak fuel, which Jet needle clip position 3rd groove would be a fire hazard. Pilot air screw 2.0 turns out HOW TO AVOID THE HAZARD Carburetor adjustments should only be performed by a Yamaha dealer. Do not 8-19...

  • Page 121: Carburetor Setting Chart

    Jet needle clip position 1st groove 3rd ( Standard ) 1. Main jet number Carburetor setting chart Altitude 0–1,500 m (5,000 ft) Above 1,500 m (5,000 ft) Temperature Main jet Jet needle Pilot air screw Main jet Jet needle Pilot air screw Above 0°C #200 3rd groove...
  • Page 122 Changing the settings of the carburetors 6. Remove the fuel tank by removing the bolts. To change the settings of the carburetors, you need to disassemble and remove them. Follow the procedures for both carburetors. Disassembling and removing the carburetors 1.
  • Page 123 8. Remove the carburetor cap securing plate by removing the screw. 1. Joint screw (× 4) 10. Remove the carburetor cap. 11. Remove the throttle cable from the throttle valve, and then remove the throttle cable 1. Carburetor cap securing plate 2.
  • Page 124 2. Needle valve 3. Main jet screws. 14. Change the main jet and the jet needle clip position. (See page 8-20.) NOTE: Optional main jets can be obtained at a Yamaha dealer. 1. Float chamber 2. Screw (× 4) 8-23...
  • Page 125 Assembling and installing the carburetors Assemble and install both carburetors by the fol- lowing steps. 1. Install the needle valve and float. 2. Install the float chamber by installing the screws. 3. Install the carburetor and tighten the joint screws. 4.
  • Page 126 Adjusting the throttle cables 4. If not, loosen the locknut and turn the NOTE: adjusting nut until the specified position is obtained. After the jet needle clip position is changed, the throttle cables may need to be adjusted. 1. Move the throttle lever a few times. 2.

  • Page 127: Idle Speed Adjustment

    EBU03021 Idle speed adjustment NOTE: A diagnostic tachometer must be used for this procedure. NOTE: The throttle cables and carburetor synchro- nization must be set properly before adjusting 1. Pilot air screw the idle speed. 2. Remove the seat. 3. Start the engine and warm it up for a few 1.
  • Page 128 4. Connect the tachometer and set the idle 8 Idle speed adjust screws were preset to the specified idling speed by turning the at the factory. When adjusting idle idle adjust screws. Turn the adjusting speed, turn the right and left idle speed screws in direction a to increase the adjust screws the same amount, or engine speed, and in direction b to...

  • Page 129: Throttle Lever Adjustment

    EBU00307 Throttle lever adjustment NOTE: Adjust the engine idling speed before adjust- ing the throttle lever free play. 1. Loosen the locknut. 2. Turn the adjusting bolt until the throttle lever free play is 4–6 mm (0.16–0.24 in). 3. Tighten the locknut. 1.

  • Page 130: Front And Rear Brake Pad Inspection

    The indicators allow checking of brake pad wear without disassembling the brake. Apply the brake and inspect the wear indica- tors. If they are ALMOST in contact with the disc plate, ask a Yamaha dealer to replace the pads. Front 1. Wear indicator 1.

  • Page 131: Brake Fluid Level Check

    EBU13040 Brake fluid level check Front Insufficient brake fluid may let air enter the brake system, possibly causing the brakes to become ineffective. Before riding, check that the brake fluid is above the minimum level mark and replenish if necessary. A low brake fluid level may indi- cate worn brake pads and/or brake system leakage.

  • Page 132: Brake Fluid Replacement

    8 Brake fluid may deteriorate painted sur- faces or plastic parts. Always clean up spilled fluid immediately. 8 Have a Yamaha dealer check the cause if the brake fluid level goes down. 8-31...

  • Page 133: Front Brake Lever Free Play

    The front brake lever should have a free play POTENTIAL HAZARD of zero mm (zero in) at the lever end. If not, Operating with improperly serviced or have a Yamaha dealer check the brake sys- adjusted brakes. tem. WHAT CAN HAPPEN You could lose braking ability, which could lead to an accident.

  • Page 134: Brake Pedal Height Adjustment

    The top of the brake pedal should be posi- POTENTIAL HAZARD tioned 10 mm (0.39 in) below the top of the Operating with improperly serviced or footrest. If not, have a Yamaha dealer adjust adjusted brakes. WHAT CAN HAPPEN You could lose braking ability, which could lead to an accident.

  • Page 135: Parking Brake Adjustment

    NOTE: A. Cable length If the cable cannot be adjusted to specification, consult a Yamaha dealer 1. Fully loosen the locknut and the adjusting bolt at the clutch lever. 4. Tighten the locknut at the clutch lever.
  • Page 136 5. Screw in the adjusting bolt at the rear q WARNING brake caliper by hand until it feels tight, POTENTIAL HAZARD then screw it out 1/8 turn. Tighten the Operating with improperly adjusted locknut to the specified torque. brakes. WHAT CAN HAPPEN The brakes could malfunction, causing reduced braking performance.

  • Page 137: Adjusting The Rear Brake Light Switch

    EBU00833 EBU00539 Adjusting the rear brake light switch Clutch adjustment The rear brake light switch, which is activated The clutch lever free play should be 5–10 mm by the brake pedal and brake lever, is properly (0.20–0.39 in). If the free play is incorrect, adjusted when the brake light comes on just adjust as follows.

  • Page 138: Drive Chain Slack Check

    EBU11440 EBU00351 Drive chain slack check Drive chain slack adjustment 1. Loosen the rear wheel hub bolts. NOTE: Move the ATV back and forth and find the tight- est position of the drive chain. Check and/or adjust the chain slack while it is in this tightest position.

  • Page 139: Lubricating The Drive Chain

    EBU00805 Lubricating the drive chain The drive chain must be cleaned and lubricat- ed at the intervals specified in the periodic maintenance and lubrication chart, otherwise it will quickly wear out, especially when riding in dusty or wet areas. Service the drive chain as follows.

  • Page 140: Cable Inspection And Lubrication

    Lubricate the inner cables and the cable ends. tain substances that could damage the O- If the cables do not operate smoothly, ask a rings. Yamaha dealer to replace them. 8-39...

  • Page 141: Brake And Shift Pedal/Brake And Clutch Lever Lubrication

    Recommended lubricant: Yamaha chain and cable lube or SAE 10W30 motor oil EBU00737 Brake and shift pedal/brake and clutch lever lubrication Lubricate the pivoting parts of each lever and pedal. Recommended lubricant: Lithium-soap-based grease (all-purpose grease) EBU15060 Lubricating the front upper and lower arm...

  • Page 142: Rear Arm Pivot Lubrication

    EBU00987 Rear arm pivot lubrication Lubricate the rear arm pivots. Recommended lubricant: Lithium-soap-based grease 8-41...

  • Page 143: Wheel Removal

    EBU01112 Rear Wheel removal 1. Loosen the wheel nuts. 2. Elevate the ATV and place a suitable stand under the frame. 3. Remove the nuts from the wheel. 4. Remove the wheel. Front EBU00871 Wheel installation When installing the wheel, reverse the removal procedure.

  • Page 144: Replacing The Headlight Bulb

    EBU01139 Replacing a headlight bulb If a headlight bulb burns out, replace the bulb as follows. 1. Remove the screw holding the headlight unit assembly to the headlight body. 1. Bulb holder cover 3. Turn the bulb holder counterclockwise to remove the defective bulb.
  • Page 145 q WARNING 4. Put a new headlight bulb into position and secure it in place with the bulb holder. POTENTIAL HAZARD 5. Install the bulb holder cover. A headlight bulb is hot when it is on and immediately after it is turned off. WHAT CAN HAPPEN You can be burned, or a fire could start if the bulb touches something flammable.

  • Page 146: Headlight Beam Adjustment

    Make sure the bulb holder cover is secure- ly fitted over the bulb holder and seated against the reflector. It is advisable to have a Yamaha dealer make this adjustment. 6. Install the headlight unit assembly. 7. Adjust the headlight beam if necessary.

  • Page 147: Tail/Brake Light Bulb Replacement

    EBU00861 Tail/brake light bulb replacement 2. Remove the defective bulb from the bulb 1. Remove the bulb holder (together with the holder by pushing it inward and turning it bulb) by turning it counterclockwise. counterclockwise. 1. Bulb holder 1. Bulb holder 2.

  • Page 148: Troubleshooting

    Yamaha dealer. Do not smoke when checking the fuel system. Make sure there are no open The skilled technicians at a Yamaha dealer- flames or sparks in the area, including ship have the tools, experience, and know- pilot lights from water heaters or fur- how to properly service your machine.

  • Page 149: Troubleshooting Chart

    2. Compression Kick the kick starter There is compresson Compression normal to see if there is compression No compression Ask a Yamaha dealer to inspect Wipe clean with 3. Ignition dry cloth Remove plugs and Spark good Ignition system normal...

  • Page 150: Engine Overheating

    Wait until the reservoir tank and/or radiator. engine has cooled. Restart the engine. If the engine overheats again, ask a Yamaha dealer to inspect and/or Level is OK. repair the cooling system. NOTE: If it is difficult to get recommended coolant, tap water can be temporarily used, provided that it is changed to the recommended coolant as soon as possible.
  • Page 151 q WARNING POTENTIAL HAZARD Removing the radiator cap when the engine and radiator are still hot. WHAT CAN HAPPEN You could be burned by hot fluid and steam blown out under pressure. HOW TO AVOID THE HAZARD Wait for the engine to cool before removing the radiator cap.

  • Page 152: No Spark

    EBU00414 No spark HOW TO AVOID THE HAZARD Throttle OverRide System (T.O.R.S.) is incor- Have the system checked by a Yamaha porated in the ignition circuit, and if the sys- dealer. tem should fail, the spark plug will not spark.

  • Page 153: Cleaning And Storage

    EDU00415 CLEANING AND STORAGE A. CLEANING Excessive water pressure may cause water Frequent, thorough cleaning of your machine seepage and deterioration of wheel bear- will not only enhance its appearance but will ings, brakes, transmission seals and elec- improve its general performance and extend trical devices.
  • Page 154 q WARNING 7. Clean the seat with a vinyl upholstery cleaner to keep the cover pliable and POTENTIAL HAZARD glossy. Operation with wet brakes after wash- 8. Automotive type wax may be applied to all ing. painted and chrome plated surfaces. WHAT CAN HAPPEN Avoid combination cleaner-waxes.

  • Page 155: Storage

    EBU00529 5. Block up the frame to raise all wheels off B. STORAGE the ground. Long term storage (60 days or more) of your 6. Tie a plastic bag over the exhaust pipe machine will require some preventive proce- outlet to prevent moisture from entering. dures to guard against deterioration.

  • Page 156: Specifications

    EBU00428 SPECIFICATIONS Model YFZ350 Dimension: Overall length 1,855 mm (73.0 in) Overall width 1,100 mm (43.3 in) Overall height 1,080 mm (42.5 in) Seat height 800 mm (31.5 in) Wheel base 1,280 mm (50.4 in) Ground clearance 135 mm (5.31 in) Minimum turning radius: 3,600 mm (141.7 in) Basic weight:...
  • Page 157 Model YFZ350 Engine oil (2-cycle): Type Yamalube R, Castrol R30, A545, A747 Mixing ratio See page 5-6. Transmission oil: Type Yamalube 4 (10W30) or SAE 10W30 Recommended engine oil classification: API Service SE, SF, SG type or higher In order to prevent clutch slippage (since the engine oil also lubricates the clutch), do not mix any chemical additives.
  • Page 158 Model YFZ350 Fuel: Type Premium unleaded fuel only, Premix Tank capacity 12.0 L (2.6 Imp gal, 3.2 US gal) Reserve amount 2.5 L (0.6 Imp gal, 0.7 US gal) Carburetor: Type/quantity VM26SS/2 Manufacturer MIKUNI Spark plug: Type/manufacturer BR8ES/NGK Spark plug gap 0.7–0.8 mm (0.028–0.031 in) Clutch type: Wet, multiple-disc...
  • Page 159 Model YFZ350 Gear ratio 32/13 (2.461) 29/16 (1.812) 27/18 (1.500) 25/20 (1.250) 23/22 (1.045) 21/24 (0.875) Chassis: Frame type Steel tube frame Caster angle 9° Trail 40 mm (1.57 in) Tire: Type Tubeless AT21 × 7 - 10 Size front AT20 ×...
  • Page 160 Model YFZ350 Suspension: Front suspension Double wishbone Rear suspension Swingarm (link suspension) Shock absorber: Front shock absorber Coil spring/Oil damper Rear shock absorber Coil spring/Gas-Oil damper Wheel travel: Front wheel travel 230 mm (9.1 in) Rear wheel travel 220 mm (8.7 in) Electrical: Ignition system C.D.I.

  • Page 161: Noise Regulation

    EBU13640 NOISE REGULATION TAMPERING WITH NOISE CONTROL SYSTEM PROHIBITED: Federal law prohibits the following acts or the causing thereof: (1) The removal or rendering inopera- tive by any person other than for purposes of maintenance, repair, or replacement of any device or element of design incorporated into any new vehicle for the purpose of noise control prior to its sale or delivery to the ultimate purchaser or while it is in use or (2) the use of the vehicle after such device or element of design has been removed or rendered inoperative by any person.

  • Page 162: Maintenance Record

    EBU13670 MAINTENANCE RECORD Copies of work orders and/or receipts for parts you purchase and install will be required to document maintenance done in accordance with the warranty. The chart below is printed only as a reminder to you that the maintenance work is required. It is not acceptable proof of maintenance work. MAINTENACE DATE OF SERVICING DEALER...
  • Page 163 EBU00433 13-1...
  • Page 164 Attention: Warranty Department faction at the time of sale, and upon your request at any later date. Each Yamaha ATV dealer is held responsible for his setup, service and war- This will ensure that Yamaha Motor Corporation, U.S.A. has an up-to-date ranty repair work.
  • Page 165 EBU00436 Indicates a potential hazard that could result in serious injury or death.
  • Page 166 EBU00437 PROTECT YOUR INVESTMENT...
  • Page 167 9 with a passenger - passengers affect balance and steering and increase risk of losing control. LOCATE AND READ OWNER’S MANUAL. FOLLOW ALL INSTRUCTIONS AND WARNINGS. (For replacement manual, call 1-800-532-1558) YAMAHA MOTOR CO., LTD. PRINTED IN JAPAN PRINTED ON RECYCLED PAPER 2004.3-1.1x1 !
  • Page 168 8 TAKE THE FREE HANDS-ON TRAINING COURSE OFFERED BY YAMAHA – ASK YOUR DEALER FOR DETAILS OR CALL 1-800-887-2887 If you have any questions about these points, or if you purchased your ATV from an authorized Yamaha dealership and were not informed of the age recommendation for your ATV by the dealership, please fill out the information below and mail this card to yamaha today.
  • Page 169 NO POSTAGE NECESSARY IF MAILED IN THE UNITED STATES FIRST CLASS PERMIT NO. 4 CYPRESS, CA POSTAGE WILL BE PAID BY ADDRESSEE YAMAHA MOTOR CORPORATION U.S.A. P.O. BOX 6555 CYPRESS, CALIFORNIA 90630-9989 ATTN: SALES ADMINISTRATION...

This manual is also suitable for:

Banshee yfz350t

Table of Contents