Page 1
Installation Built-In Dishwasher Instructions If you have questions, call 800-944-9400(US), 800-245-8352 (Canada) or visit our website www.Frigidaire.com BEFORE YOU BEGIN IMPORTANT - The dishwasher Read these instructions completely MUST be installed to allow for future removal from carefully. the enclosure if service is required.
Page 2
Installation Preparation PARTS SUPPLIED: Two #8 Phillips flat head wood screws, 5/8" long to secure dishwasher to underside of countertop (in literature package). Two Phillips head, color matched toekick screws (in 2 Wood Screws 2 Color Matched Screw Type literature package). Toekick Screws Hose Clamp MATERIALS...
Installation Preparation PREPAREDISHWASHERENCLOSURE • The dishwasher must be installed so that drain hose is no more than 10 feet in length for proper drainage. • The dishwasher must be fully enclosed on the top, sides and back, and must not support any part of the enclosure.
Installation Preparation PREPARE ELECTRICAL WIRING WARNING FOR PERSONAL SAFETY: Remove house fuse or open circuit breaker before beginning installation. Do not 1-1/2"Dia. use an extension cord or adapter plug Hole(Max.) with this appliance. Electrical Requirements • This appliance must be supplied with 120V, 60 Hz., from Cabinet and connected to an individual properly grounded...
Installation Instructions PREPARE HOT WATER LINE BEFORE YOU BEGIN • The line may enter from either side, rear or floor Locate and set aside the package containing within the shaded area shown in Figure E 2 Phillips head countertop mounting screws •...
Installation Instructions _STEP 2 ADJUST LEVELING LEGS STEP 4 INSTALL 90 ° ELBOW • Move the dishwasher close to the installation location • Wrap 90 ° elbow with thread seal tape. ° Install a 90 ° elbow onto the water valve. and lay it on its back.
Installation Instructions STEP 7 SLIDE DISHWASHER STEP 5 pOSITION WATER LINE AND HOUSE WIRING PARTIALLY INTO CABINET DO NOT PUSH AGAINST FRONT PANEL ° Position water supply line and house wiring on the WITH KNEES. DAMAGE WILL OCCUR. floor of the opening to avoid interference with base of dishwasher and components under dishwasher.
UNDER COUNTERTOP STEP 8 POSITION DISHWASHER ° Check to be sure that wires are secure under the dishwasher and not pinched or in contact with door springs or other dishwasher components. TIP: Check tub insulation blanket, if equipped. It should be positioned so it is not bunched up or interfering with door springs.
Page 9
Installation Instructions STEP 10] SECURE DISHWASHER STEP 11 CONNECT WATER SUPPLY TO COUNTERTOP OR CABINET In this step you will need the 2 Phillips special head Connect water supply to 90 ° elbow. screws set aside prior to Step 1. The dishwasher must •...
Installation Instructions [STEP 12]CONNECT DRAIN LINE DRAIN LINE INSTALLATION FOLLOW ALL LOCAL CODES AND ORDINANCES. • Connect drain line to air gap, waste tee or disposer using either previously determined method. The drain hose molded end will fit 5/8", 3/4" or 1" diameter connections on the air gap, waste tee or Method 1 - Air gap with waste tee or disposer ____...
Installation Instructions [STEP 13]CONNECT POWER STEP 14 PRE-TEST CHECKLIST SUPPLY Review this list after installing your dishwasher to avoid charges for a service Skip this step if equipped with power cord. call that is not covered by your warranty. Verify that power is turned off at the source.
Installation Instructions [STEP 15] DISHWASHER WET TEST STEP 16 REPLACE TOEKICK Turn on power supply (or plug power cord into outlet, if equipped). Turn dial to Normal "Wash" position. Close door. Check to be sure that water enters the dishwasher. If water does not enter the dishwasher, check to be sure that water and power are turned on.