GE JDS28 Installation Instructions Manual
Hide thumbs
Also See for JDS28:
- Owner's manual (25 pages) ,
- Installation instructions manual (17 pages) ,
- Owner's manual (48 pages)
Table of Contents
Quick Links
See also:
Owner's Manual
JIlnstallation
JElectric
nstructlons
Drop-In Range
JDS28,
JDP39
[-_
Questions?
Call 800.GE.CARES
(800.432.2737)
or Visit
our Website
at: www.GEAppliances.com
I
BEFORE YOU BEGIN
• Proper
installation
is the
responsibility
of the
installer
and product
failure
due to improper
Read these
instructions
carefully
and
completely.
• iMPORTANT
- Save t hese
instructions
for local inspector's
use.
• iMPORTANT
- Observe all
governing
codes
and ordinances.
Note
to installer
- Be sure to leave these
instructions
with
the consumer.
Note to Consumer
- Keep these
instructions
for future
reference.
installation
is NOT covered
under the warranty.
NOTE - This appliance
must
be properly
grounded.
ATTENTION
iNSTALLER
All electric
drop-in
ranges
must
be hard wired
(direct
wired)
into an approved
junction
box.
A plug and receptacle
is NOT permitted
on
these
products.
PARTS INCLUDED
%%
2 Shoulder
Screws
(for
stop
device)
2 Screws
MATERIALS
NEEDED
Junction
Box
Strain
Relief
Clamp
for
1/2"
conduit
Wire
Nuts
TOOLS YOU WILL NEED
1/8"
Drill Bit and
Electric
or Hand
Drill
L
J
Level
Phillips
Screwdriver
Standard
Screwdriver
Nut
Driver
Tape Measure
Hammer
Straight
Edge
or Square
_
_
Pencil
Safety Glasses
Hand or Sabre Saw
31-10595-1
(11-04
JR)
1
Table of Contents
Related Manuals for GE JDS28
Summary of Contents for GE JDS28
- Page 1 JElectric Drop-In Range JIlnstallation JDS28, JDP39 Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: www.GEAppliances.com BEFORE YOU BEGIN • Proper installation is the responsibility of the installer and product failure due to improper Read these instructions carefully installation is NOT covered under the warranty.
-
Page 2: Important Safety Instructions
Installation Instructions IMPORTANT SAFETY INSTRUCTIONS FOR YOUR SAFETY ELECTRICAL REQUIREMENTS WARNING: For p ersonal safety, This appliance must be supplied with proper voltage and frequency, and connected remove house fuse or open circuit breaker to an individual, properly grounded branch before beginning installation. -
Page 3: Pre-Installation
To obtain Kits: a. Visit GE Web Site (See page 1) b. Call GE Answer Center (See page c. Contact Dealer Hin( e clears slot NOTE: The oven door is very heavy. Be sure... -
Page 4: Pre-Installation Cutout And Required Clearances
Installation Instructions PRE-INSTALLATION CUTOUT AND REQUIRED CLEARANCES Overall Depth 26=5/8" NOTE: Drop-In Ranges are designed hang from the countertop only. Do not install on a platform or support rails. Follow instructions packaged with alternate appliances. (24" rain. dim, must be maintained between COOking surface... -
Page 5: Prepare To Install The Range
Installation Instructions PREPARE TO INSTALL THE RANGE STANDARD INSTALLATION Flea' 1/4" min. flat 25" typically 9/16" min. flat Range support ..I" 29-15/16" 30-1/16" smooth cut Countertop Braces secured between underside of the countertop the cabinet if required to obtain 1-1/4"... -
Page 6: Electrical Connections
Installation Instructions ELECTRICAL CONNECTIONS WARNING: connection Remove house fuse or open circuit Improper breaker. of aluminum house wiring to copper leads can result in an electrical hazard or fire. Use only Loosen screws for the junction box cover connectors designed for joining copper to and rotate... - Page 7 Installation Instructions NEW CONSTRUCTION THREE=CONDUCTOR BRANCH FOUR-CONDUCTOR BRANCH CiRCUiT CONNECTION CIRCUIT CONNECTION When connecting to a 3-conductor branch circuit, if local codes permit: • When installing in new construction, • When installing oven in a mobile home Connect the bare oven ground conductor recreational...
- Page 8 Installation Instructions ELECTRICAL CONNECTIONS (CONT.) Reinstall Junction box cover. Do not shorten the flexible conduit. The conduit strain relief clamp must be securely attached the junction box and the flexible conduit must be securely attached to the clamp, if the flexible conduit will not fit within...
-
Page 9: Install The Range
Installation Instructions INSTALL THE RANGE iNSTALLiNG THE ANTI-TIP Select the proper position for the countertop thickness and move bracket to proper position. BRACKET (Unit is supplied with bracket in position The anti-tip bracket is attached to the back of the Drop-In Range. - Page 10 Installation Instructions INSTALL THE RANGE (CONT.) _-I iNSTALL STOP SCREW PLACING THE RANGE INTO THE OPENING These screws prevent the range from sliding out of position during operation. It is suggested that people lift the range into place, carefully setting the side metal flanges on the edges...
- Page 11 Installation Instructions CHECK FOR PROPER ATTACH THE LOWER TRIM INSTALLATION OF THE Attach lower trim (supplied separately with STOP SCREW the range) to the bottom of the vertical side trim with the 2 screws supplied. Look at both sides of the range under the door.
-
Page 12: Replacing The Oven Door
Installation Instructions INSTALL THE RANGE (CONT.) REPLACING THE OVEN DOOR Push the hinge locks up against the front frame of the oven cavity, to the locked NOTE: The oven door is heavy. You may need position. help lifting the door high enough to slide it Hinge in into the hinge slots. -
Page 13: Final Checklist
Installation Instructions FINAL CHECKLIST = Check to make sure the circuit breaker is closed (Reset) or the circuit fuses are replaced. g Be sure power is in service to the building. g Check to be sure that all packing materials and tape on metal panel... -
Page 14: Alternate Construction
Installation Instructions ALTERNATE CONSTRUCTION PREPARATION OPTIONAL MAINTOP FILLER OR ISLAND INSTALLATION BACKGUARD When installing in an island or other non-standard location, countertop cutout If counter opening extends to the wall, it will dimensions must be according to page 5. require Maintop Filler Kit (JXS66XX) Backguard... - Page 15 Notes...
- Page 16 Notes Printed in the United States...