Page 1
TranScape View ™ ™ TranScape Wave ™ ™ HC3/GN3 H990 H770 Instant Hot Water Dispenser Owner’s Manual Installation, Care & Use Instalacion, cuidado & uso Installation, soin et utilisation...
Page 2
® We are delighted that you have chosen the InSinkErator ® Instant Hot Water Dispenser to be a part of your home. This unique appliance will save you time and effort in the kitchen, and you’ll enjoy discovering new uses for it each day. That’s exactly why millions of people are now using an InSinkErator Instant Hot Water Dispenser.
Page 3
Identify the model of your instant hot water dispenser and record it here:________________ HC-View-SS H-View-SS HC-Wave-SS H-Wave-SS HC3-SS GN3-SS H990-SS H770-SS HOW TO USE THIS INSTRUCTION MANUAL These instructions are separated into main sections, indicated by numbers, and subsections, indicated by capital letters. The manual is setup this way to allow you to take a break at any point after completing a section or subsection without affecting the installation process.
Maximum counter faucet, tank and filter (if applicable). center of hole to wall thickness (depth) ■ ■ Check to make sure there is proper HC-View-SS ..2 ⁄ " ......3" clearance (see chart at left) for H-View-SS ..2 ⁄...
Page 6
INSTALLING THE FAUCET - VIEW/ WAVE View/Wave ■ ■ Unpack dispenser components. ■ ■ On a firm, flat surface, carefully straighten the copper tubing using hands only. Property Damage: Do not pinch or break copper tubing. Do not distort the last 1 inch of tubing. View/Wave For a standard 1 "...
Page 7
INSTALLING THE FAUCET - HC3/ GN3 HC3/GN3 ■ ■ Unpack dispenser components. ■ ■ On a firm, flat surface, carefully straighten the copper tubing using hands only. ■ ■ Remove the wing nut from Property Damage: Do not pinch or break copper the valve body.
Page 8
INSTALLING THE FAUCET - H990 H990 ■ ■ Unpack dispenser components. ■ ■ On a firm, flat surface, carefully straighten the copper tubing using hands only. Property Damage: Do not pinch or break copper tubing. Do not distort the last 1 inch of tubing. H990 ■...
Page 9
INSTALLING THE FAUCET - H770 H770 ■ ■ Unpack dispenser components. ■ ■ On a firm, flat surface, carefully straighten the copper tubing using hands only. Property Damage: Do not pinch or break copper tubing. Do not distort the last 1 inch of tubing. H770 ■...
Page 10
MOUNTING THE TANK ■ ■ Select a spot under the sink to mount tank vertically within reach of both Tank must be plumbing and electrical connections. mounted level The tank should be within 16" or less to ensure of faucet water lines and within 30" proper operation.
Page 11
Available as an option; INSTALLING FILTRATION (Optional) separate purchase required. ■ ■ Mark hole locations for filter head and bracket in a spot that allows for filter replacement. ■ ■ Drill 1/8" starter holes and attach bracket to wall with wood screws, turning until snug.
Page 12
FINAL WATER CONNECTION HC-View / HC-Wave / HC3 ■ ■ Install a T-fitting (not included) Brass Nut Ferrule onto the cold water supply line. Brass Inser ■ ■ Install dedicated water control valve with 3/8" compression fitting. ■ ■ Plastic At the end of the white 3/8"...
Electric Shock Hazard: Using an ungrounded or improperly connected appliance can result in serious injury or death from electrical shock. This appliance must be grounded. This instant hot water dispenser is equipped with a cord that has a grounding conductor and a grounding pin. The plug must be connected to an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
CARE AND USE Electric Shock Hazard: To prevent electrical shock, disconnect power before servicing unit. Use only a properly grounded and polarized electric outlet. ADJUSTING THE THERMOSTAT PROPERTY DAMAGE ■ ■ Regularly inspect the unit for any signs of Factory temperature pre-set is 200˚F. approx.
Please read Troubleshooting Guide and/or visit www.insinkerator.com before calling AnswerLine ™ TROUBLESHOOTING PROBLEM POSSIBLE CAUSE WHAT TO DO Water and steam spits • Unit is boiling. • Activate faucet lever to release some water from forcefully from spout the tank. May be normal during initial setup.