Contents 5 Product specifications 1 Important Safety 6 Troubleshooting Care for your product Care of the environment Help and support 7 Notice Compliance 2 Your SoundSphere DesignLine Trademarks speakers Introduction What's in the box Overview of the main speaker Overview of the remote control 3 Get started Unpack and install the SoundSphere DesignLine speakers...
1 Important • Do not install near any heat sources such as radiators, heat registers, stoves, or other devices (including amplifiers) that produce heat. • Protect the power cord from being Read and understand all instructions before you use your product. If damage walked on or pinched, particularly at plugs, is caused by failure to follow instructions, convenience receptacles, and the point...
• Remove batteries when the unit Risk of overheating! Never install this apparatus in a confined space. Always is not used for a long time. leave a space of at least four inches around • Risk of swallowing coin battery! this apparatus for ventilation.
Help and support For extensive online support, visit our website at www.philips.com/support to: • download the complete user manual • print the quick start guide •...
Check and identify the contents DesignLine of your package: speakers Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome. Always there to help you Register your product and get support at www.philips.com/welcome...
Overview of the main speaker a Tweeter pole d SWAP L/R b Power indicator • Swap to the left or right audio channel, so that you can place the main speaker • Light up red in sleep mode. at either side of your TV based on the •...
i AUX IN L/R • Connect to the analog audio output • Turn on the music sound effect. sockets on the TV or an external device. • Turn on the movie sound effect. j APD (on)/ (off) d SURR OFF/ON •...
3 Get started Caution • Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation. Always follow the instructions in this chapter in sequence. Unpack and install the SoundSphere DesignLine speakers Place the SoundSphere...
Unscrew the speaker connectors. Connect Insert fully the end of a speaker cable with red mark into the left red (+) connector. This section helps you connect your SoundSphere DesignLine speakers Screw the left red (+) connector to secure to a TV and other devices. the cable.
Page 12
HDMI (ARC) Using a High Speed HDMI cable, connect the HDMI OUT (ARC) socket on your SoundSphere DesignLine speakers to the HDMI ARC socket on the TV. The HDMI ARC socket on the TV • might be labeled differently. For details, Connect digital devices through see the TV user manual.
• Through analog audio cables, connect the AUX IN L/R sockets on your SoundSphere DesignLine speakers to the AUDIO OUT sockets on the TV or other devices. Connect power Caution • HDMI OUT Risk of product damage! Make sure that the power supply voltage matches the voltage printed on the bottom of the unit.
Prepare the remote control Turn on Caution • Press . » The SoundSphere DesignLine speakers • Risk of explosion! Keep batteries away from heat, switch to the last selected source. sunshine or fire. Never discard batteries in fire. » The source indicator lights up in the corresponding color.
4 Use your Play audio and watch SoundSphere video from a digital device connected through HDMI IN DesignLine speakers HDMI OUT This section helps you use the SoundSphere DesignLine speakers to play audio from connected devices. HDMI HDMI (ARC) Play audio from your TV connected through HDMI ARC Make sure that both the digital device and the TV are connected to HDMI IN and...
Enable/disable Dolby night mode Play audio from an external device connected through The Dolby night mode, also called DRC analog audio sockets (Dynamic Range Control), allows you to select a quiet sound or full dynamic sound. When the Dolby night mode is enabled, the volume of loud sound is decreased while the volume of soft sound (such as speech) is increased.
Philips PS1 Bluetooth for 3 seconds and then press to reset the Bluetooth connection. • Philips does not guarantee 100% compatibility with all Bluetooth devices. Press Bluetooth on the remote control to switch the SoundSphere DesignLine speakers to Bluetooth mode.
Select a preset sound effect • During play, press to select the music or movie sound effect. To experience an immersive audio experience with virtual surround sound output: Press SURR ON to turn on the surround • sound effect. • To turn off the virtual surround sound effect, press SURR OFF.
5 Product Remote control batteries specifications • 1 x CR2025 Note • Specifications and design are subject to change without notice. Amplifier • Power specification: 2 x 100W @ 0.1% • Frequency response: 20Hz - 20KHz +0 dB / -1dB •...
Page 20
HDMI IN connector on your request service. If you still have a problem, SoundSphere DesignLine speakers. get support at www.philips.com/support. • On the remote control, select the correct audio input. Main unit •...
Page 21
Quality of audio play from a connected Bluetooth device is poor. • The Bluetooth reception is poor. Move the device closer to the SoundSphere DesignLine speakers, or remove any obstacle between the device and the SoundSphere DesignLine speakers. The connected Bluetooth device connects and disconnects constantly.
Page 22
Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in Philips and the Philips’ Shield Emblem are the United States and other countries. registered trademarks of Koninklijke Philips N.V. and are used by WOOX Innovations Limited under license from Koninklijke Philips N.V.
Page 24
This product was brought to the market by WOOX Innovations Limited or one of its affiliates, further referred to in this document as WOOX Innovations, and is the manufacturer of the product. WOOX Innovations is the warrantor in relation to the product with which this booklet was packaged. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. PS1_UM_12_V2.0...