Related Manuals for Moog MP-201
Summary of Contents for Moog MP-201
- Page 1 MP-201 Multi-Pedal Manual Firmware v2.0 Addendum...
- Page 2 CV LAG; MIDI output follows Foot Pedal movement with no lag. This way if you record MIDI while sweeping the foot pedal and then play back the MIDI to the MP-201, the channel CV Output will respond exactly as it did the first time, when the pedal movement was recorded.
- Page 3 The GATE / EG parameter allows you to select GATE or ENVELOPE CV output for this channel. Envelope Generation is a major new feature for the MP-201. Envelopes appear as CV Output only; the MIDI output for Gate channels is the same regardless of GATE / EG setting.
- Page 4 “decelerating change in voltage,” but these names might be confusing to the user, and, more to the point, they would not fit on the MP-201 display. In actual use, you should experiment to find what envelope shape gives the best effect for your purpose, and remember that the COMPLEX envelope setting allows you to choose a different shape for each envelope stage, to assemble precisely the envelope shape you want to hear.
- Page 5 Note. If the MP-201 CV Scale is set to UNIPOLAR (all CV outputs are restricted to the range 0V to +5V), then the Root Note is the lowest note that will play; all MIDI notes below this will also cause the CV output to be zero Volts.
- Page 6 MIDI to CV channel also clears and resets the channel's note stack, which can be used to clear any stuck notes if they occur. Note stacks on the MP-201 are used by Gate channels (if Gate Source = MIDI Notes) and by MIDI to CV channels; in both cases you have an eight-note stack which is monophonic, with last-note priority.
-
Page 7: Midi Setup
(7) MULTI PGM CHANGE - "Send All At Once" sends Program Change messages for all channels of an MP-201 preset at once, and only sends them when the preset is first loaded. "Send Per Channel" sends each MP-201 channel's Program Change message any time that channel is toggled from Off to On. - Page 8 [7] SEND SYSEX: All MP-201 Sysex-sending functions have been collected on this new menu. (1) SEND ALL PRESETS - Send a bank of 100 MP-201 user presets as one SysEx file. (2) SEND PRESET - Send the currently-active preset as a 310-byte SysEx file.
- Page 9 MP-201 Multi-Pedal Manual Firmware v2.0 Addendum Map of MP-201 v2.0 EDIT menu: parameters are listed per CHANNEL MODE below. EXPRESSION HEEL VALUE (0 - 4095) TOE VALUE (0 - 4095) INITIAL VAL (0 - 4095) CV LAG (OFF, ON) if “ON”...
- Page 10 MP-201 Multi-Pedal Manual Firmware v2.0 Addendum LFO WAVEFORM (TRIANGLE, SQUARE, SAW DOWN, RAMP UP, S+H) LFO SYNC (FREE RUNNING, TAP TEMPO, CH1-4, MIDI CLOCK) LFO RATE (0 - 4095 or MIDI Clock Divisions) LFO AMOUNT (0 - 4095) LFO OFFSET...
- Page 11 MP-201 Multi-Pedal Manual Firmware v2.0 Addendum COMMON PARAMETERS (all channel modes) CHAN NAME (8 characters) INITIALSTATE (OFF, ON) CHANNEL MODE (EXPRESSION, GATE, LFO, MIDI TO CV, NOISE) MIDI CHANNEL (OFF, 1-16) if MIDI Channel not OFF: PGM CHANGE# (OFF, 0 - 127)
- Page 12 EGRLOOP4 PED.GATE PED.GATE GATE EX.PED:2 PEDGATE3 GATE REV.EXP4 CVLAGFUN RISE LAG FALL LAG HEEL-LAG TOE-LAG 40-100 EXPRESSR CHANNEL 1 CHANNEL 2 CHANNEL 3 CHANNEL 4 © 2009 Moog Music Inc. Page | 12 Specifications subject to change without notice moogmusic.com...