Table of Contents
Specification
Common specification
Power source
AC 220~240V 50Hz
Television system
System I
Colour system
PAL
(PAL/NTSC3.58 in AV mode)
Channel coverage
UHF: 21-69,
Aerial input impedance
75 ohm
AV terminal
AV1: CENELEC Standard
Input: Composite video, RGB and audio-L/R
Output:TV-output with composite video and
AV2:
Input: Composite video, RGB, S-VHS and
Output:Monitor-output with composite video
AV3: CENELEC Standard
Input: Composite video, and audio-L/R
Side AV terminal
AV4:
Input: Composite video and audio-L/R
Headphone socket
Mini Jack
CE27LD4-B
CE27LD4BK-B
Sound output
(Continuous)
2 x 10W
Contrast Ratio
900:1
Screen(inches)
27
(viewing measured diagonally)
Display Resolution
1280 x 720 (WXGA)
Viewing angles
H:176°, V:176°
Dimensions
(WxHxD mm)
800 x 470 x 239
(including stand)
Weight (kg)
14.4
(including stand)
Helpful hints
NO PICTURE, NO SOUND
Check if TV is plugged in.
Try a different channel, if OK, probably station trouble.
POOR PICTURE, SOUND OK
Adjust BRIGHTNESS control.
Adjust FINE TUNING control.
Check aerial connections.
NO COLOUR, PICTURE OK
Adjust COLOUR control.
Adjust FINE TUNING control.
Is the programme in colour ?
WEAK PICTURE
Check aerial connections on back of set.
Check aerial for broken wires.
Re-orient aerial.
SPECIFICA
TION / HELPFUL
SPECIFICA
TION / HELPFUL
audio-L/R
CENELEC Standard
audio-L/R
and audio-L/R
RCA jacks
CE32LD4-B
CE32LD4BK-B
2 x 10W
1000:1
32
1366 x 768 (WXGA)
H:176°, V:176°
922 x 545 x 239
17.5
HINTS
HINTS
The following faults are not caused by the receiver:
"GHOSTS"
Reflections of signals from mountains or high buildings will cause
multiple images, called "Ghosts". These abnormal conditions can be
reduced to minimum by repositioning aerial or by installing new one
suited for your area.
"INTERFERENCE"
Interference may be caused by electrical appliances, car ignition
systems, etc. This should normally be a temporary condition, but
should this interference persist, contact your dealer.
Plug and Play Helpful hints.
If you do not fit an aerial into this TV set the Plug and Play feature
may start up each time you switch on your TV.
To prevent this follow these instructions.
1. Switch on your TV set, the Plug and Play screen appears.
2. Press the MENU button on the remote control to clear the Plug and
Play screen.
3. A second screen will appear. Press the Return key to clear from the
screen.
4. Press the D/A key to return to Analogue.
5. Press the MENU button to select the Menu screen. (as shown
below).
Timer
Sound
Sound
Preset
Picture
Fine Tuning
6. Select Preset Menu by pressing the 1 or 2 button.
7. Select Prog. Preset by pressing the 6 or 5 button and enter
Semi by pressing the 1 button.
8. Press the 6 button and select Memory. Press OK button to
cancel. (The OK? changes to OK).
Semi
Channel
Position
Skip
Memory
9. The next time you switch on your TV set the Plug and Play screen
will not appear.
Setting
Auto Tuning
Auto Sort
Prog. Preset
- -
Swap
C24
01
OFF / ON
OK?
21
- Quick Links:
- Remote Control
- Main Menu
Hide quick links:
Table of Contents
