Table of Contents
Quick Links
Table of Contents
Related Manuals for Bosch MAN-REG-X-08
Summary of Contents for Bosch MAN-REG-X-08
- Page 1 INSTALLATION INSTRUCTIONS REG-X...
- Page 2 MAN-REG-X-08 IMPORTANT SAFETY INSTRUCTIONS Read these instructions. Keep this instruction. Heed all warnings. Follow all instructions. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with manufacturer instructions. Do not install near any heat sources such as...
- Page 3 plug does not t into your outlet, consult an electrician for replacement of the obsolete outlet. 9. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the power where they exit from the apparatus. 10.
- Page 4 CSA Certified / UL Listed CLASS 2 power adaptors must be used in order to comply with electrical safety standards. Bosch Security Systems, Inc. will not be responsible for injuries or damages resulting from the improper installation or use of any product sold by Bosch Security Systems, Inc their agents, distributors or dealers.
- Page 5 PSU box. Contact BOSCH Service Center for further advice...
-
Page 6: Table Of Contents
INDEX – REG-X Camera Description………………………………………………...7 Unpacking………………………………………………..8 Parts List…………………………………………………..8 Items Required for Installation…………………………..8 Initial Preparations………………………………………..9 Guidelines………………………………………………..9 1. Mechanical Specifications REG-X…………..…….10 2. Input Power / Video Output Connections…………11 3. Mounting Specification………..……………………12 4. Camera Adjustment………………………………...16 5. Troubleshooting Guide…...………………….……..17 6. General specifications…………..………….………20... -
Page 7: Description
DESCRIPTION The REG-X license plate capture camera unit consists of one IR-sensitive monochrome camera and one integrated panel of Infrared LEDs. The license plate capture camera produces optimum license plate images during day and night settings in all-weather conditions. The camera has technology that helps block out unwanted light such as headlamps or sunlight, thus ensuring no bloomed-out or washed-out images of the license plates. -
Page 8: Unpacking
Check the parts list and confirm all items have been located. Inspect the equipment thoroughly to ensure nothing was damaged in transit. Contact BOSCH Service Center if a problem is noted, see the rear page of this booklet for contact numbers. PARTS LIST (items supplied with unit) -
Page 9: Initial Preparations
INITIAL PREPARATIONS • Determine the operating voltage at the installation site. The camera‘s Voltage Regulator Board accepts both 12-24VDC and VAC input without change to internal connections. See Section 2, Input Power/Video Output Connections. • Determine the optimum location for the camera. See Section 3, Mounting Specification. -
Page 10: Mechanical Specifications Reg-X
1. MECHANICAL SPECIFICATIONS – REG X (See Section 6 - General Specifications, for more information) Front View Side View Bottom View Showing mounting holes *Optional mounting kit is available to mount the camera onto an electrical box; Part Number: WZMB.001 Figure 1 - General Mechanical Specifications... -
Page 11: Input Power / Video Output Connections
2. INPUT POWER / VIDEO OUTPUT CONNECTIONS The camera incorporates an electrically isolated power board for safe and easy 12 to 24 VDC/VAC operation. Note: Input voltage is 12VDC to 24VDC for DC input. The AC input range is 12VAC to 24VAC. Power Input Leads 12 to 24 VDC/VAC... -
Page 12: Mounting Specification
3. MOUNTING SPECIFICATION Caution: Install with appropriate screws to suit mounting surface. Select a suitable location protected from accidental damage, and tampering. Mounting location must not expose the REG-X camera to environmental conditions exceeding the camera’s specification. See page 20. Caution: Ensure the selected location is protected from falling objects, contact with moving objects, and accidental interference from personnel. - Page 13 The REG-X units have a horizontal field of view of about 6ft – 8ft (1.8m – 2.4m) at the specified capture range distance for the REG-X as shown on Figure 3 below. Since most vehicles have license plates mounted in the center of the front or back and the normal width for a standard traffic lane in a controlled parking or access lane is 8ft to 10ft (2.4m –...
- Page 14 º The maximum angle of the camera to the car is 40 in combination of both horizontal and vertical angles. This limits the amount of skew of the letters on the number plate. If the letters are skewed too much the license plate will be difficult to recognize.
- Page 15 Range Figure 5 - Maximum Horizontal Angle If the maximum range is exceeded the letters will become smaller and be more difficult to read. At the max range the width of the number plate covers approximately 12% of the width of the screen. Note: The Range is the distance from the camera to the license plate.
-
Page 16: Camera Adjustment
CAMERA ADJUSTMENT Warning! Do not pan or twist beyond 360° Do not tilt beyond 90° Do not apply excessive force when adjusting Figure 6 - Adjustment Set Screws 1) Mount and secure the REG-X unit according to specification (see Section 3). 2) Using the provided hex key, loosen all three set screws on bracket as shown in Fig 6. -
Page 17: Troubleshooting Guide
5. TROU BLESHOOTING GUIDE PROBLEM POSSIBLE LIKELY SOLUTION CAUSE No Video 1. Power Check the input power Supply connections at the Connection terminal block, ensuring no wires are loose. Voltage The supply range is: Range 12 - 24VDC OR 12 – 24VAC. Measure the input voltage to the camera. - Page 18 If still no video, contact BOSCH Service Center. See rear page of this manual for contact information. Check the coax cable shield is not touching “ground”, e.g. at the Horizontal Ground couplings. Scan Looping on...
- Page 19 Only qualified personnel shall install Bosch Security System, Inc. product. Bosch Security System, Inc. will not be responsible for injuries or damages resulting from the improper installation or use of any product sold by Bosch Security System, Inc., their agents, distributors or dealers.
-
Page 20: General Specifications
6. GENERAL SPECIFICATIONS Power Consumption: 6.5W max Input Voltage: 12 – 24 VDC or 12 – 24 VAC Enclosure (housing): Robust Aluminum extrusion (sealed to IP66) Viewing Window: Black Acrylic 98mm Diameter (3.8”) Dimensions: 219mm Length (8.6”) (Length includes bracket) Operational º... - Page 21 Note:...
- Page 22 Note:...
- Page 23 Note:...
- Page 24 Phone: +65 6319 3450 Telephone+1 888-289-0096 Phone: + 31 40 2577 284 Fax: +65 6319 3499 +1 585-223-9180 Fax: +31 40 2577 330 [email protected] Email: [email protected] [email protected] www.boschsecurity.com www.boschsecurity.us www.boschsecurity.com © Bosch Security Systems, Inc. 2011; Data subject to change without notice.