Available languages
Available languages
Quick Links
See also:
Use and Care Manual
Installation
Instructions
for French
Door
Bottom
Freezer/Refrigerator
Tools Necessary:
Prepare
The Installation
Site
Your refrigerator is designed to be part of a built-in
kitchen cabinet system. Be sure to coordinate site
preparation and installation with you r kitchen contractor.
Include these minimum guidelines in your site preparation:
,
Choose a place near a grounded electrical outlet.
,
Do not use an extension cord or an adapter plug.
,
Avoid direct sunlight and close proximity to a range,
dishwasher or other heat source.
•
Floor should be level and able to support a fully
loaded refrigerator.
,
The refrigerator's Ice & Water Dispenser requires
water supply access.
,
Plan for easy access to counter tops when
removing food.
,
For complete access to drawers and freezer
baskets, doors must be able to fully open.
Allow the following clearances for ease of installation, proper air circulation, and plumbing and
electrical connections:
Sides & Top: 3/8 inch / Rear: 1 inch
Transport
Unpackaged
Refrigerator
To Site
By now, you have already removed your refrigerator's shipping carton.
I
You may still need to use a hand truck to move it through close spaces or
entrances. If the refrigerator is larger than an entrance, consider two options:
Remove the entrance door if one exists.
I
•
Remove the refrigerator doors (see how in your Use & Care Guide).
When us nga hand truck:
,
Load refrigerator from side of cabinet only.
,
Do not run retaining straps over handles.
,
Do not over-tighten retaining straps.
,
Never use refrigerator handles to move the
refrigerator.
•
Remove tape from doors only after unit is in place.
Connect
Water
Supply
What you will need:
,
Access to a cold f",/_A
roll t==X====_
water line with
,_L/o_
_o_eq
pressure of
_'/,_
30-1 O0 psi.
Copper tubing
with 1A-inch
(6.4mm) OD. Length for this tubing
is the distance from the rear of the
refrigerator to your household water
supply line plus 7 feet (2.1 meters).
A shut-off valve for the connection between your
household water line and the refrigerator supply
line. Do not use a self-piercing shut-off valve.
A compression nut and ferrule (sleeve) for the
water supply connection at the rear of your
refrigerator.
To connect the water supply
to the rear of your refrigerator:
1 Ensure that the refrigerator is not plugged in.
2 Flush the supply line until water is clear by placing the
end of the copper tube in a sink or bucket and opening
the shut-off valve.
3 Remove the plastic cap from the water valve inlet at the
rear of your refrigerator. Discard the cap.
4 Slide the brass compression nut, then the ferrule (sleeve)
onto copper tube.
5 Push the copper tube into water valve inlet as far as it will
go (1/4 inch).
6 Slide the ferrule (sleeve) into valve and finger-tighten the
compression nut onto valve. Tighten another half turn with
a wrench. Do not over=tighten.
7 Secure the copper tube to your refrigerator's rear panel
with a steel clamp and screw (see illustration).
8 Coil the excess copper tubing (about 21/2turns) behind
your refrigerator as shown. Arrange coiled tubing to avoid
vibration or wear against other surfaces.
_\
_i
I;f,,.....
[
\\
/!
/I
o Doe_
_Steel
\
'J
I
f/d_[!
Clamp
I
Brass
Z_-w /
!"-_b°, _t@ t "I--I
{sl,_ol
A'-.I
_,°2t:_
I H. _ J --
to Water
Tank
)' _-
Water Valve
I!1
III
_ >_yd¢
\J
Ill
///
/_
_atetVaive
_r_"
Copper
water
line
_de
enoug
from
household
water
supply
h tubing
in loop
to aUow
moving
refrigerator
out
for
cleaning.)
9 Open water supply shut-off valve and tighten any connections that leak.
Place
In Permanent
Position
If possible, use a hand truck to position the refrigerator
I
!_u_rlto_
directly in front of its cabinet enclosure.
Be careful not to move the refrigerator beyond its water
supply (copper tubing) connections,
i i _ h
iiii_
Plug in the power cord, and push the refrigerator straight
_;i
back into place.
:
:
!(iei (_!!
5
Level
Refrigerator
& Adjust
Doors
(if necessary)
Guidelines for final positioning of your refrigerator:
All four corners of the cabinet must rest firmly on the
floor.
The cabinet should be level at the front and rear.
The sides should tilt 1A-inch (6 ram) from front to back (to
ensure that doors close and seal properly).
Doors should align with each other and be level.
To level the cabinet using the front rollers:
1 Open both doors and remove the toe grille by gently pulling forward.
(See illustration 1.)
2 Close the doors and use a flat-blade screwdriver or 3/8 inch socket
wrench to raise or lower the front rollers. (See illustration 2
3 Ensure both doors are bind-free with their seals touching
_ecabinet on
all four sides.
To level the doors using the lower hinge:
1 if the refrigerator door is lower than the freezer door, raise he
refrigerator door by turning the adjustment screw clockwise. (See
illustration 3.)
2 if the freezer door is lower than the refrigerator door, raise he freezer
door by turning the adjustment screw clockwise. (See
ation 3.)
3 Ensure door stop flange is touching hinge flange, if not, readjust as
necessary. (See illustration 4.)
4 Replace the toe grille by fitting it into place.
[
satisfied
with the installation
of your refrigerator?
D Pleasecontact the store you purchased it from.
This document
should
only be removed
by customer
after
installation.
Remove
Internal
Shippin
Materials
Electrolux uses packing foam and tape to secure the internal parts of your refrigerator for
shipping. Once the refrigerator is in position, you can remove this material.
SHELF
SPACER
SHELF
SPACER
TAPE
TAPE
TAPE
TAPE
BIN SPACER
CABLE
TIE(S)
CABLE
TIE(S)
--
--SHELF
SPACER
--TAPE
SPACER
W/HANDLES
TAPE
SPACER
CABLE
TIE(S)
--
Locationof these materials may vary depending on your model.
Problems?
Try These
Suggestions
Operation problems are possible if any of the installation tasks are not completed. Here is a list of
things to check for:
,
is the refrigerator's power cord plugged in?
,
is the refrigerator connected to the household water supply?
,
if you had to remove the refrigerator and freezer doors, did you reattach water and power
connectors at the door hinges? (See the Use & Care Guide for detailed instructions on
removing and replacing doors.)
•
is the ice maker power switch turned On?
Other possibilities to check:
is the power to the receptacle turned on?
is the water filter above the fresh food compartment fully seated (see Use & Care Guide for details)?
if you still have operation problems after checking these suggestions, please see the "Solutions
To Common Problems" section in your Use & Care Guide.
What's
Next?
Congratulations. You are ready to begin enjoying your new Electrohx refrigerator.
To become aware of important safety instructions and learn how to operate your refrigerator,
please read the entire Use & Care Guide.
You may want to start with the "Normal Operating Sights & Sounds" section of the Guide to
learn more about what to expect during typical operation.
Please register your product. You can register online at www.electrohxusa.com,
or you can
simply send in the Registration Card.
And thank you for choosing Electrolux.
[]Installation
Checkoff
List
Doors
ice Maker
[]
Handles are secure and tight
[]
House water supply connected to
refrigerator
[]
Door seals completely to cabinet on all
[]
No water leaks present at all connections
sides
- recheck in 24 hours
[]
Fresh food doors are level
[]
Ice Maker is turned ON.
[]
Ice & Water Dispenser operates correctly
[]
Refrigerator is level, side to side and tilted
[]
Front filter must be flush with filter
1/4" (6mm) front to back
housing (some models)
[]
Toe grille is properly attached to
Final Checks
refrigerator
[]
Cabinet is setting solid on all corners
[]
Shipping material removed
Bectrical
Power
[]
Fresh Food and Freezer temperatures
set
[]
Crisper Humidity controls set
[]
House power turned on
[]
Registration Card sent in
[]
Refrigerator plugged in
Not
P/N:241940500
Related Manuals for Electrolux EI28BS55IB - 27.8 cu. Ft. Refrigerator
Summary of Contents for Electrolux EI28BS55IB - 27.8 cu. Ft. Refrigerator
- Page 1 2 Flush the supply line until water is clear by placing the f/d_[! Clamp Electrolux uses packing foam and tape to secure the internal parts of your refrigerator for end of the copper tube in a sink or bucket and opening Brass shipping.
- Page 2 _dea_e Lave la tuberfa de suministro hasta que el agua salga limpia Electrolux usa cinta y espuma de empaque para fijar las piezas internas del refrigerador para su transporte. colocando el extremo de la tuberfa de cobre en el fregadero...
- Page 3 Placez I'extremit_ de la conduite en cuivre dans un 6vier ou un seau, Electrolux utilise de la mousse et du ruban d'emballage pour proteger les pi_ces internes de votre r_frigerateur puis ouvrez le robinet...