Mitsubishi Electric PJLink FD630U User Manual
Lan control utility
Hide thumbs
Also See for PJLink FD630U:
- Specifications (2 pages) ,
- Specfications (2 pages) ,
- Manual (11 pages)
Table of Contents
LAN Control Utility
User Manual
1. Introduction ............................................................................................... 2
2. Setup ......................................................................................................... 4
3. Main screen............................................................................................... 7
4. Projector registration ............................................................................... 10
5. Operation of projector.............................................................................. 14
6. Schedule setting...................................................................................... 16
7. E-mail setting........................................................................................... 19
8. ProjectorView .......................................................................................... 20
9. Visual PA2 (Visual PA2 enabled projectors only).................................... 25
10. Telnet setup (Telnet enabled projectors only) ......................................... 28
11. PJLink ..................................................................................................... 29
12. Others ..................................................................................................... 30
1.1. Preparing to use network features.......................................................................... 2
1.2. Functions and features ........................................................................................... 2
1.3. Operation environment ........................................................................................... 2
2.2. When deleting "ProjectorView Global+" (Uninstallation)......................................... 5
2.3. Connection.............................................................................................................. 6
3.1. System settings ...................................................................................................... 9
4.2. When changing the projector IP settings .............................................................. 12
4.3. When changing projector settings ........................................................................ 13
4.4. When deleting projector registration ..................................................................... 13
5.1. Operation of projector by remote controller .......................................................... 14
5.2. Confirmation of projector status............................................................................ 15
6.1. Creation of projector group ................................................................................... 16
6.2. When changing schedule setting.......................................................................... 17
6.3. When deleting group............................................................................................. 18
7.1. Connection with E-mail server .............................................................................. 19
7.2. E-mail setting ........................................................................................................ 19
7.3. Sending test E-mail............................................................................................... 19
8.1. Main functions....................................................................................................... 20
8.2. Starting ProjectorView .......................................................................................... 20
8.3. Entering projector information............................................................................... 22
8.4. Setting the network password............................................................................... 23
8.5. Resetting the network settings.............................................................................. 24
9.1. Starting Visual PA2............................................................................................... 25
9.2. Saving messages entered and settings specified in Visual PA2 .......................... 26
9.3. Loading saved data in Visual PA2 ........................................................................ 26
9.4. Deleting data from Visual PA2.............................................................................. 26
9.5. Configuring the Schedule function of Visual PA2 ................................................. 27
11.1. About PJLink......................................................................................................... 29
12.1. Troubleshooting .................................................................................................... 30
12.2. Supported Projectors ............................................................................................ 30
Contents
Table of Contents
Related Manuals for Mitsubishi Electric PJLink FD630U
Summary of Contents for Mitsubishi Electric PJLink FD630U
-
Page 1: Table Of Contents
LAN Control Utility User Manual Contents 1. Introduction ....................2 1.1. Preparing to use network features................2 1.2. Functions and features ................... 2 1.3. Operation environment ................... 2 2. Setup ......................4 2.1. Installation of "ProjectorView Global+" ..............4 2.2. When deleting "ProjectorView Global+" (Uninstallation)......... 5 2.3. -
Page 2: Introduction
1. Introduction 1.1. Preparing to use network features • Installing the ProjectorView Global+ • Assigning the projector IP address • Configuring settings such as PASSWORD, E-mail Setting, Language, and PJLink Certification Setting by running Telnet (Telnet enabled projectors only) or using ProjectorView The projector IP address, password, and PJLink certification can be configured on the projector main screen. - Page 3 1. Introduction ® ® Microsoft and Windows are the registered trademark or trademark of Microsoft Corporation in the United States and other countries. (The official name of Windows is Microsoft Windows Operating System.) Pentium is the trademark or registered trademark of Intel Corporation or its subsidiaries in the United States and other countries.
-
Page 4: Setup
2. Setup 2.1. Installation of "ProjectorView Global+" Before starting installation, be sure to read "ReadMe.txt" contained in the CD-ROM. Copy ProjectorView Global+v2.msi contained in the Tools folder of CD-ROM to the hard disk of your personal computer. (1) Double click "ProjectorView Global+v2.msi", and start up the installer of "ProjectorView Global+". -
Page 5: When Deleting "Projectorview Global+" (Uninstallation)
2. Setup (5) When the installation has been completed, click [Close]. 2.2. When deleting "ProjectorView Global+" (Uninstallation)• When uninstalling "ProjectorView Global+", "ProjectorView Global+" should be ended in advance. If the application continues operating, uninstallation can not be performed normally. (1) Double click "ProjectorView Global+v2.msi", and start up the installer of "ProjectorView Global+". -
Page 6: Connection
2. Setup 2.3. Connection Connect the controller PC and the projector, which have installed "ProjectorView Global+", to a commercially available LAN cable. When connecting multiple projectors, use a commercially available hub. • A LAN terminal is required for the controller PC. •... -
Page 7: Main Screen
3. Main screen Menu bar Configuration You can specify the following settings: • Add New Group: You can create a new group. • Edit Schedule Setting: You can edit schedule settings set for existing groups. • Search Projector: Automatically searches available projectors. - Page 8 3. Main screen Select All All projectors currently displayed on the projector list can be set to selected/non selected state. Exit You can exit "ProjectorView Global+". However, you cannot exit the application during the automatic projector search and the projector status loading.
-
Page 9: System Settings
3. Main screen 3.1. System settings (1) Select "System Configuration" from "Configuration" of the menu bar on the main screen. • "System Configuration" window is displayed. (Default settings are shown in the following example.) Item Description Language You can select the user interface language, Japanese or English. Refresh Status Cycle You can set the cycle to obtain the projector status. -
Page 10: Projector Registration
4. Projector registration 4.1. Registration of projector to "ProjectorView Global+" The procedures to register projectors vary among the foregoing connection examples. • In connection examples 1 and 2 (where projectors are installed within the same local network), the projectors within such network are automatically detected and registered. For details, see procedure A below. •... -
Page 11
4. Projector registration Procedure B - Connection example 3 (where projectors are installed via a router) To automatically detect projectors connected via a router, confirm the IP address in the projector network menu and specify a range of IP addresses to search that particular IP address using "Search Projector Setting".
... -
Page 12: When Changing The Projector Ip Settings
4. Projector registration• Set the default gateways of the projectors and PC correctly. For details, contact your network administrator. • Be sure to make a note of the IP addresses and default gateways you set. If you forget the setting values, you may not be able to detect the projectors again. -
Page 13: When Changing Projector Settings
4. Projector registration 4.3. When changing projector settings (1) Select the projector which you like to change from the projector list on the main screen. (2) Select "Edit Projector Setting" from "Configuration" of the menu bar. • "Edit Projector Setting" window is displayed. (3) Set the Projector Name and its group and the theft detector. -
Page 14: Operation Of Projector
5. Operation of projector 5.1. Operation of projector by remote controller Group or single unit of projector can be operated. (1) Select the projector which you like to operate from the projector list on the main screen. • When selecting more than one projector simultaneously, select while pressing the Ctrl key. (2) Click [Remote Controller] of the tool bar on the main screen or when you like to operate a certain projector, double click the projector on the projector list on the main screen. -
Page 15: Confirmation Of Projector Status
5. Operation of projector 5.2. Confirmation of projector status The status of the projector is displayed on the projector list on the main screen. Item Description Check Theft detector setting (ON/OFF) Projector list registration number Projector Name Projector name set in the application MAC Address MAC address of the projector IP Address... -
Page 16: Schedule Setting
6. Schedule setting 6.1. Creation of projector group Multiple projectors can be controlled and batched by sorting groups. Also, each group can set each time of the power supply ON/OFF every day. Since the schedule of the power supply ON/OFF is performed by each group, the projector which you like to operate at the same schedule should be integrated into the same group. -
Page 17: When Changing Schedule Setting
6. Schedule setting• The power supply ON and the power supply OFF can not be selected at the same time of the same day of the week. • The Schedule Setting will be executed while "ProjectorView Global+" is in operation. •... -
Page 18: When Deleting Group
6. Schedule setting 6.3. When deleting group (1) Select the group which you like to delete from the Group select pull-down menu on the main screen. (2) Select "Edit Schedule Setting" from "Configuration" of the menu bar. • "Edit Schedule Setting" window is displayed. (3) Click [Delete]. -
Page 19: E-Mail Setting
7. E-mail setting When the communication with the projector monitored by the theft detector is disrupted, a warning E-mail can be sent to the designated address, enabling to serve for early detection of the projector theft. The E-mail setting can not be set at every projector and every group. The same setting should be set for all projectors. -
Page 20: Projectorview
8. ProjectorView ProjectorView is a web-browser based remote control and monitoring tool for network projectors. If you use the projectors listed in page 30, see ProjectorView in "LAN Control Utility" User Manual included with the projector. 8.1. Main functions • It displays the status of network projectors (such as the name of the projector, lamp temperature, lamp hours, errors and alerts). -
Page 21
8. ProjectorView
• If lamp mode is set to "STANDARD", "Lamp time" displayed may be longer than "Operation time". ProjectorView main window (REMOTE CONTROL) When you click REMOTE CONTROL, the Remote Control window is displayed. You can click the buttons displayed in the window to remotely control the projector. -
Page 22: Entering Projector Information
8. ProjectorView An example: Sending an alert message when the lamp change required. ProjectorView Alert: The lamp has reached the maximum usage time. Replace the lamp and reset the lamp counter. Please see the user manual for detailed instructions. Projector name : abc Projector model : XY1234 Installed date : 2008/01/01 Installed location : 10Factory-5F... -
Page 23: Setting The Network Password
8. ProjectorView The following table explains each item. Item Description Projector name Enter a unique name to identity the projector. Installed date Enter the date when the projector is installed. Installed location Enter the place where the projector is located. SMTP IP address Enter the IP address of the SMTP server used for sending e- mails.(e.g.192.168.0.1) -
Page 24: Resetting The Network Settings
8. ProjectorView (3) Enter the New network password and Confirm network password, and then click [OK]. • If passwords entered match, the window closes to save the changes. • If passwords entered do not match, an error message is displayed. When you click [OK], the new network password window reappears. -
Page 25: Visual Pa2 (Visual Pa2 Enabled Projectors Only)
9. Visual PA2 (Visual PA2 enabled projectors only) Visual PA2 is a feature to display messages on the projector screen. It can be used for all active Visual PA2 enabled projectors. Additionally, the projector is capable of reading aloud on-screen messages using the Text Speech function. Note that some projectors may not have this function. -
Page 26: Saving Messages Entered And Settings Specified In Visual Pa2
9. Visual PA2 (Visual PA2 enabled projectors only) 9.2. Saving messages entered and settings specified in Visual PA2 You can save messages entered in Textbox, as well as settings specified for Text, Frame, Location, and Text Speech. These must be saved before you activate the Schedule function in the Visual PA2 window. (1) Enter text in Textbox, specify settings for Text, Frame, Location, and Text Speech, and then click [Save]. -
Page 27: Configuring The Schedule Function Of Visual Pa2
9. Visual PA2 (Visual PA2 enabled projectors only) 9.5. Configuring the Schedule function of Visual PA2 By using the Visual PA2's Schedule function, your intended messages can be displayed on the screen at a set time. (1) Click [Edit] in the Schedule area. •... -
Page 28: Telnet Setup (Telnet Enabled Projectors Only)
10. Telnet setup (Telnet enabled projectors only) You can set the password for ProjectorView, a web-based remote control and monitoring tool for network projectors, and the industry standard protocol PJLink based remote projector management tool, the display language on the ProjectorView, the LAN controlled mode, and the PJLink certification mode by running Telnet on the projector screen. -
Page 29: Pjlink
For the details of supported command, see the projector's User Manual "Supervising and controlling by computer". This projector, which is equipped with LAN terminal and manufactured by Mitsubishi Electric Corporation, is fully compliant to the specifications of JBMIA PJLink Class 1. It supports all the commands defined by PJLink Class 1, and the compliance has been verified with the PJLink standard specifications Version 1.0. -
Page 30: Others
12. Others 12.1. Troubleshooting • The projector can not be recognized. The projector may not be recognized automatically due to the setting of fire wall. In such case, the communication of "ProjectorView Global+" should be registered as an exception to the fire wall. For the setting of the fire wall, see the manual of the software that configures the fire wall.