LG Monitor Installation Manual
  1. Manuals
  2. Brands
  3. LG Manuals
  4. Monitor
  5. Monitor
  6. Installation manual

LG Monitor Installation Manual

Signage models
Hide thumbs
Table of Contents

Quick Links

MONITOR SIGNAGE MODELS
•Openframe
•Media Player
•Transparent Signage
•Video Wall
Table of Contents
loading

Related Manuals for LG Monitor

Summary of Contents for LG Monitor

  • Page 1 MONITOR SIGNAGE MODELS •Openframe •Media Player •Transparent Signage •Video Wall...

  • Page 2: Table Of Contents

    CONTENTS OPENFRAME SIGNAGE 1-1. Keep temperature 0°C ~ 40°C(Mandatory) 1-2. Consider using a cooling & heater solution(Mandatory) 1-3. Do not disassemble Handle, Fan or Side bracket(Mandatory) 1-4. Do not use a screw is longer than 9.0mm(Mandatory) 1-5. Recommend not to place the front panel in direct sunlight 1-6.

  • Page 3: Openframe Signage

    OPENFRAME SIGNAGE 1-1. Keep temperature 0°C ~ 40°C(Mandatory)  When designing the enclosure, the temperature inside the enclosure must be maintained between 0°C and 40°C. The Measurement method for checking the operating temperature inside the enclosure Enclosure Openframe Signage (eg. 47WX50MF) Thermal sensor Example 1.

  • Page 4: Consider Using A Cooling & Heater Solution(Mandatory)

    1-2. Consider using a cooling & heater solution (Mandatory)  To maintain the temperature inside the enclosure, you may consider using a cooling and heater solution such as an air conditioner, heat exchanger, or combined cooler and heater depending on the external environment. (Please see below examples) ...

  • Page 5: Do Not Disassemble Handle, Fan Or Side Bracket(Mandatory)

    1-3. Do not disassemble Handle, Fan or Side bracket (Mandatory)  Do not disassemble the parts such as Handle, Fan or Side bracket for preventing of product safety & function problem Handle *47WX50MF Side bracket...

  • Page 6: Do Not Use A Screw Is Longer Than 9.0Mm(Mandatory)

    1-4. Do not use a screw is longer than 9.0mm (Mandatory) 47WX50MF Side Hole  You must use the side screw holes when mounting the panel  The Side screw holes are M4.0 Tap , Torque 4~5Kgf.cm, pitch 0.7mm  The Screw hole depth of the panel is:9.0mm (Max) ...

  • Page 7: Recommend Not To Place The Front Panel In Direct Sunlight

    1-5. Recommend not to place the front panel in direct sunlight • It is recommended not to place the front panel in direct sunlight. • For Example-Using a canopy may prevent the enclosure temperature increase due to direct sunlight. Good Example NOTE •...

  • Page 8: Use The Side Bracket To Mount Into The Enclosure

    1-6. Use the side bracket to mount into the enclosure • You should use the side bracket to mount the signage display into the enclosure. 47WX50MF Side Bracket 1-7. Refer to brightness of according to ambient luminance •This is measurement of 47WX50MF’s Auto Brightness Control function Auto Brightness Control Curve(47WX50MF) Ambient Luminance Brightness...

  • Page 9: Media Player

    MEDIA PLAYER 2-1. Minimum distance between media player and structure (100mm) • Monitor Back Cover Mount Condition • Application model : NC1000, NA1000, NA1100, MP500, PC100 • Minimum distance between player & structure : 100mm distance to X,Y,Z axis direction •...

  • Page 10: Install Dust Filter & Keep Temperature 0°C ~ 40°C(Mandatory)

    2-2. Install Dust filter & keep temperature 0°C ~ 40°C (Mandatory) • Embedded Mount Condition • Application model : NC1000, NA1000, NA1100, MP500, PC100 • Minimum distance between media player and structure : 100mm distance to X,Y,Z axis direction •Should install dust filter in ventilation area •...

  • Page 11: Transparent Signage

    TRANSPARENT SIGNAGE 3-1. Preparation for Installation • Preparation for Installation • Please refer to the “LVDS Pin Map Guide” in the manual. (26TS30MF/47TS30MF) • Need to purchase separately the below items Preparation Items...

  • Page 12: Portrait Mode: Rotate The Set Clockwise 90°(Mandatory)

    3-2. Portrait mode: Rotate the set clockwise 90°(Mandatory) • Portrait Layout(Only supported for 47TS30MF) • To install in portrait mode, rotate the set clockwise 90 degrees when looking at the front. (The AD board should support portrait mode) Landscape Portrait CAUTION •...

  • Page 13: How To Connect Cable Assembly

    3-4. How to connect cable assembly Cable assembly...

  • Page 14: Refer To Ventilation Hole Of Enclosure

    3-5. Refer to ventilation hole of enclosure •Transparent Signage enclosure construction Front view Back view Side view Opening the door view 3-6. Refer to lighting set up •Transparent Signage enclosure construction Working display with enclosure Side type lighting Ceiling type lighting...

  • Page 15: Refer To Storage Place(Ad Board & Media Player)

    3-7. Refer to storage place (AD Board, Media Player) • Example of storage place located under enclosure ▪ Storage space of equipment...

  • Page 16: Dimension Of Screw Holes(26Ts30Mf/47Ts30Mf)

    3-8. Dimension of Screw Holes Transparent Signage enclosure construction  Dimension of Screw Holes : You should use M3 screws to mount the monitor. There are 16ea(26”),20ea(47”) prepared screw holes on the rear side of the product.  Caution : The length of screw can vary according to thickness of the enclosure guide frame.

  • Page 17: Recommendation: Lighting Is 600 Lux Or More

    3-9. Recommendation: Lighting is 600 LUX or more  This product must be installed with lighting.  The Lighting must be installed behind the product so that the display can be seen clearly. Example of lighting 600 lux or more Side type lighting 600 lux or more Ceiling type lighting...

  • Page 18: Video Wall

    Video wall Precaution 4-1. Precaution in movement  Adhere to the warning signs printed on the Box. Don’t tumble the Set box sideward down. Model: 47WV30MS 47WV30BR 47WV30BS 47WV30-BAAM 47WV30-BAAL Don’t lie on or lean on the Set box.

  • Page 19: Precaution In Movement & Handling

    Precaution in Handling  Move the Set as a team of 2 persons.  When you move the bare Set, please use one hand on grabbing the handle and the other support under the Set. CAUTION  This way up/ Fragile/ Keep away from rain/ Stacking limit 4.
  • Page 20 Causes & Phenomena of the Line Defect The line defect would occur on your Set if you strike on the edge of the Set. LOG (LINE ON GLASS) DEFECT Shock on Module Left/Top Corner Left/Top LOG Crack Horizontal Line Defect LOG (LINE ON GLASS) DEFECT Shock on Module Top Side ...
  • Page 21 Do not Collide & Install with enough airflow  Be careful not to collide the sets with the floor or with each other.  Install in the space with enough airflow Panel Panel...

  • Page 22: Installing The Product

    4-2. Installing the Product Cut Packing Strap of the Box. Cut Tape on the Box. Open the Box and remove the top packing. Remove the Upper Box. Open the Poly Bag. Undress the Poly Bag.
  • Page 23 Lift up the Set using the SIDE/BACK Handle. Remove Bottom packing when lifting up the Set. With one hand under the set and the other hand grabbing the set, move the set. Lay the back of the Set down on the table.
  • Page 24 Use the cushion or Pad when you lay the face of the Set downward. Connect IR receiver to use remocon. And then, connect power code.
  • Page 25 CAUTION When you connect Monitor sets for multivision, you may find that the screen color is not the same across all the Monitor sets. If you want to adjust the screen color manually, please refer to the Installation Manual. When you install multiple Monitor sets onto a wall, attach the IR Receiver to all the sets, or use an RS-232C cable to connect them and then attach the IR Receiver to the first set.
  • Page 26 4-3. Tiling Displays : How to Join Sets - Installing Set 1 Example of 2 x 2 tiling The numbers assigned in this example (#1,#2, #3, #4) are used to demonstrate the installation procedure to ensure it is easy to follow. These numbers have nothing to do with the Set ID that is used to operate the remote control.
  • Page 27 4-3. Tiling Displays : How to Join Sets - Installing Set 2 Join Set 2 to Set 1 using the guide brackets on the top side of Set 1 and mount the two sets to the wall mount plate or the wall. Remove the guide brackets after mounting the sets.
  • Page 28 How to remove the guide brackets Unscrew the guide bracket screws from the rear of the set and remove the guide brackets. Once the screws are removed, the guide brackets will drop. You need to remove them through the gap on the sides of the set. This can be done only when there is enough space between the set and the wall mount plate or the wall to unscrew the screws.
  • Page 29 4-3. Tiling Displays : How to Join Sets - Installing Set 3  Fix the guide brackets to Set 3 following the steps above, and loosely mount the set to the wall mount plate or the wall. Minimize the space between the sides of the sets using the U-shaped fixture. When the sets are firmly mounted to the wall, remove the U-shaped fixtures.
  • Page 30 4-3. Tiling Displays : How to Join Sets - Installing Set 4 Loosely mount Set 4 to the wall mount plate or the wall and minimize the space between the sets using the U-shaped fixtures. When Set 4 is firmly mounted to the wall, remove the U-shaped fixtures. Remove the guide brackets.

  • Page 31: Daisy Chain Monitors

    (If you want to connect more than this number of monitors, we recommended that you use a distributor.) When the tile mode is configured via DVI cables, only the monitor that receives first signals can play HDCP-encrypted content. (The DVI Out port does not support HDCP).

  • Page 32: Function Setting(Multivision Configuration)

    4-5. Function Setting (Multivision Configuration) 1/2 1. IR Receiver connection. 2. Connecting the Power code Remote control IN port IR Receiver 3. Set ID setup for each set. (example) 2x2 Set Assign the “Set ID” to each Set as below: Set ID:1 Set ID:2 Set ID:3...
  • Page 33 4-5. Function Setting (Multivision Configuration) 2/2 6. Connect the Monitor sets, in series, using an RS-232C cable. 7. Installation Menu setup. Refer to.. “ Setting the Installation Menu” 8. Tile Mode setup. Refer to.. “ Setting the “Setting the Tile Mode”...

  • Page 34: Setting The Installation Menu

    4-6. Setting the Installation Menu (1/2) If you press the MENU button on the remote control for more than five seconds, the main menu appears and then disappears. The input data is also displayed in the upper left corner of the screen. Press the "0"...
  • Page 35 Decide to work all functions of 'Signage Mode Operation' or not. Operation 15Min Force Off Turns off the monitor if there is no input for more than 15 minutes. "No" is the recommended default value setting. 4 hours off Turns off the monitor if there is no input on the remote control for more than four hours."No"...

  • Page 36: Setting The Tile Mode

    4-7. Setting the Tile Mode  In Tile Mode you can view an image in a larger scale by connecting multiple monitors. Tile Mode Off: An input image is not enlarged, and the same image is shown on all connected monitors. Tile Mode On: An input image is enlarged according to the value in the H.

  • Page 37: Setting The Picture Id

    4-8. Setting the Picture ID (1/2)  Picture ID is used to change the settings of a specific set (display) using a single IR receiver for multi-vision. The set receiving the IR signal communicates with another set via the RS232 connector. Each set is identified by a Set ID. If you assign the Picture ID using the remote control, only displays with the same Picture ID and Set ID can be controlled remotely.
  • Page 38 4-8. Setting the Picture ID (2/2) 1. Press the ID On (Red) button 2 If you press the left/right buttons or press on the remote control. the ON button repeatedly, the Picture ID cycles through OFF and 1 to 4.Assign the ID you want.

  • Page 39: Revision History

     Revision History Version Revised Date Revised Contents  Initial version V 10 2012.12.13  Update the video wall guide V 11 2012.12.17  47TS30MF Portrait direction counterclockwise  clockwise V 12 2012.12.27  Add Direct Air Cooling Solution (47WX50MF) ...

This manual is also suitable for:

42vs2047vs2055vs2042vx3047vx3042ws10 ... Show all

Table of Contents