Electrolux EW23BC85KS3 Installation Instructions Manual

INSTALLATION

AND SERVICE

MUST BE PERFORMED

BY A QUALIFIED

INSTALLER.

IMPORTANT:

SAVE FOR LOCAL

ELECTRICAL

INSPECTOR'S

USE.

READ AND SAVE THESE

INSTRUCTIONS

FOR FUTURE

REFERENCE.

Clearances and Dimensions

1.

Provide adeauate clearances between the range and adjacent combustiblesurfaces.

2.

LocationmChecklocationwhere the ranae will be installed. Check for properelectrical supply, and the stability ofthe floor.

3.

Dimensionsthat are shown must be used. Given dimensions )rovide minimum clearance. Contact surface must be solid and level.

RANGE

RANGEELECTRICAL

FRONT

TYPICALCABINETINSTALLATION

SIDE

OVERALL

CONNECTIONS

_

VIEW

DIMENSIONS

29 1/4" with

_AIIdimensionsfor

door handle

I electricaloutlet location I

' "

30"

25-3/4"

jA.are

maximum,

j

30"

...... _

_u°--*'%'

_

zji

:_-':'--m.

Minimum*

_,o1: _to.13

i

I __j--_"-J['Dashedcubedarea

1

-_ _-

wall on either

18" cabinetson

Maximumdepth

side of range

eitherside

for cabinets

[_CentedineI showswhere the

l

®®

of range.

ma

um

above 36" height.

of range I electricaloutlet must |

l

above rangetop.

|

!

I be installedfor flush )1

........................................................................

_

,__

_--

I..,

11.. Lthe wall installation, j

1_

_25,!

_

I

II

36 + 1/8"

_:_

I

door open

"\\_29-7/8"

_

--

" < -_

Edge

maximum

_ _ _ _"

2-5/8"for models equipped

_

_ _ _

withwarmer drawers.

_

3-1/2"for models equipped

Fig.

1

with storagedrawers

Fig.

2

Fig.

3

_'_

30"

_

0" clearancebelow cookingtop and at rearof range.

*30" MINIMUMCLEARANCE BETWEENTHE TOP OF THE COOKINGSURFACE AND THE BOTTOMOF AN UNPROTECTEDWOOD OR

METAL CABINET;OR24" MINIMUMWHEN BOTTOM OFWOOD OR METAL CABINET ISPROTECTEDBY NOT LESSTHAN 1/4" FLAME

RETARDANTMILLBOARD COVEREDWITH NOT LESS THAN NO. 28 MSG SHEET STEEL, 0.015" STAINLESSSTEEL, 0.024"ALUMINUM OR

0.020"COPPER. 0" CLEARANCE ISTHE MINIMUMFOR THE REAR OF THE RANGE. FOLLOWALL DIMENSION REQUIREMENTSPROVIDED

ABOVE TO PREVENTPROPERTY DAMAGE,POTENTIALFIREHAZARD,AND INCORRECTCOUNTERTOPAND CABINET CUTS.

TO ELIMINATE THE RISKOFBURNSORFIREBYREACHING OVERHEATEDSURFACEUNITS,CABINETSTORAGESPACELOCATEDABOVE

THESURFACEUNITSSHOULDBEAVOIDED.IFCABINETSTORAGEIS TO BEPROVIDED, T HERISKCANBEREDUCEDBYINSTALLINGA

RANGEHOODTHAT PROJECTSHORIZONTALLYA MINIMUMOF5"BEYONDTHE Bo'n'OM OFTHECABINETS.

IMPORTANT SAFETY INSTRUCTIONS

_

Tip Over Hazard

• A child or adult can tip the range and

be killed.

• Verify the anti-tip device has been

installed to floor or wall.

• Ensure the anti-tip device is re-engaged when the range

is moved to floor or wall.

• Do not operate the range without the anti-tip device in

place and engaged.

• Failure to follow these instructions can result in death or

serious burns to children and adults.

_J_i

Range

leveling leg

)_o'__, :,] ^_+=_-=_

_

-_/i/_ ,-,.u--.t-,

__jJ

bracket

To check if the anti-tip bracket is installed properly, use both

arms and grasp the rear edge of range back. Carefully

attempt to tilt range forward. When properly installed, the

range should not tilt forward.

Refer to the anti-tip bracket installation

instructions

supplied with your range for proper installation.

If the information in this manual is not followed

exactly, a fire or electrical shock may result causing property

damage, personal injury or death.

Important Notes to the Installer:

•

Read all instructions contained in these installation

instructions before installing range.

•

Remove all packing material from the oven compartments

before connecting the gas & electrical supply to the range.

•

Observe all governing codes and ordinances.

•

Be sure to leave these instructions with the consumer.

Important Notes to the Consumer:

Keep these instructions with your owner's guide for future

reference.

•

As when using any appliance generating heat, there are

certain safety precautions you should follow. These are

listed in the Use & Care Guide, read it carefully.

•

Be sure your range is installed and grounded properly by a

qualified installer or service technician.

•

Make sure the wall coverings around the range can

withstand the heat generated by the range.

•

To eliminate the need to reach over the surface elements,

cabinet storage space above the elements should be

avoided.

pin 316454912 rev C

Espa_ol - Paginas 5-8