Table of Contents
Quick Links
Owner's Manual
Video Cassette Recorder
EWV603
1. Before using your VCR
Basic VCR/TV Connection
Antenna
Cable
Cable
Signal
Signal
or
(Back of TV)
Disconnect
4
Plug the AC power cords of the VCR and TV into the AC outlets.
Hint for Cable Box or Satellite Box
Connection A
(Back of VCR)
(Cable box or
ANT
Satellite box)
IN
IN
OUT
OUT
RF Cable
Cable
(supplied)
Signal
(Back of TV)
Select this connection when you want to view or record a
scrambled channel. With this connection, channels cannot
be changed on the VCR. You can view or record ONLY the
channels you have selected on the cable box or the satellite
box.
• While you are recording, only the recorded channel can
be viewed.
To select channels of the cable box or satellite box
1)Turn on the VCR by pressing the POWER button, and
then, press the VCR/TV button.The POWER and the
VCR/TV indicators on the front panel will light on. Then,
press the CHANNEL buttons to select channel 3 or 4
(the same channel as the output channel of the cable
box or satellite box).
• If you use the channel 4, you need to change the VCR's
RF output to channel 4. Refer to "RF Output Channel".
2) At the TV, select channel 3 or 4 (the same channel as
you have selected at step 1).
3) At the cable box or satellite box, select the channel you
want to view or record.
EMERSON AND THE G-CLEF LOGO ARE REGISTERED TRADEMARKS
OF EMERSON RADIO CORP., PARSIPPANY, NEW JERSEY, U.S.A.
If you need additional operating assistance after
reading this owner's manual or to order replace-
ment accessories, please call
TOLL FREE : 1-800-256-2487
or visit our web site at http://www.funai-corp.com
Antenna
(Back of VCR)
or
ANT
2
IN
3
Connect
OUT
Connect
RF Cable
(supplied)
Connection B
(Back of VCR)
ANT
(Cable box or
IN
Satellite box)
Cable
OUT
E
IN
Signal
OUT
RF Cable
(supplied)
Select this connection when you want to change channels
on the VCR. With this connection, you may watch one
channel while recording another.
• You may not view or record a scrambled channel.
To select channels of the cable box or satellite box
1)At the cable box or satellite box, select channel 3 or 4
(the same channel as the VCR's RF output channel.)
• Refer to "RF Output Channel".
2)At the TV, select the same channel as the output chan-
nel (3 or 4) of the cable box or satellite box.
3)Turn on the VCR by pressing the POWER button, and
then, press the VCR/TV button .The POWER and
VCR/TV indicators on the front panel will light on. Then,
select the channel you want to view or record.
To play back a tape
Follow the steps 1) to 2) above. Then, play back a tape.
• Refer to "Playback" on page 5.
To view one channel while recording another
1)While you are recording on the VCR, press the VCR/TV but-
ton so that the VCR/TV indicator disappears on the VCR.
2)At the cable box or satellite box, select the channel you
want to view.
RF Output Channel
If channel 3 is already occupied for broadcasting,
1) Set your TV to channel 4.
2) Insert a pre-recorded tape into the VCR.
3) Press the PLAY button once.
4) After a few seconds, press the PLAY button on the VCR for 3 seconds.
• The RF output channel will change to channel 4 from channel 3 and you will
see a playback picture.
• When a picture does not appear on the TV screen, repeat step [4].
5) Press the STOP button to stop playback.
Stereo TV Connection
You can use the AUDIO OUT jacks
and VIDEO OUT jack on the back of
the VCR if your TV has Audio/Video
(Back of TV)
Input jacks. In this case, you need to
set the TV to external Line Input Mode.
Please refer to your TV's owner's man-
ual.
Front & Rear Terminals
AUDIO OUT jacks
Connect the audio cables to the audio in
jacks of a camcorder, another VCR, a stereo
amplifier, or an audio system.
E
(Back of TV)
RF Cable
VIDEO OUT jack
Connect the video cable to the video in jack
of a camcorder, another VCR, or a TV.
POWER
CHANNEL
VIDEO
L-AUDIO-R
Supplied Accessory
• Remote control
• RF Cable
(NA372UD) with
(WPZ0901TM002)
Two AA batteries
- 1 -
VIDEO
AUDIO OUT
OUT
L
R
(Back of TV)
AUDIO IN jacks
Connect the audio cables from the audio
out jacks of a camcorder, another VCR, or
an audio source.
ANT
ANT IN jack
AUDIO
IN
L
Connect your antenna or cable box.
ANT
AUDIO
IN
OUT
IN
L
OUT
IN
R
R
ANT OUT jack
VIDEO
OUT
VIDEO
OUT
Connect the RF cable (supplied) to
OUT
IN
the antenna input jack on your TV.
OUT
IN
VIDEO IN jack
Connect the video cable from the video out
jack of a camcorder, another VCR, or an
audio-visual source (laser disc player,
MENU
REC/
video disc player, etc.).
POWER
VCR/TV
TAPE IN
TIMER
REC
Installing the Batteries for
the Remote Control
• Owner's Manual
Install two AA batteries
(0VMN03902)
(supplied) matching the
polarity indicated on
the bottom of the
remote control.
0VMN03902 / HF440UD
Hint
Hint
• The RF output channel may
not change when you adjust
tracking during playback. In
this case, stop the playback,
and start the playback again.
After that, press the PLAY
button on the VCR for 3 sec-
onds again.
VIDEO
AUDIO IN
IN
L
R
ANT
AUDIO
IN
L
OUT
IN
R
OUT
VIDEO
OUT
IN
Audio/Video Cables
(not supplied)
ANT
IN
1
OUT
Connect
(Back of VCR)
Printed in China
★★★★★
Table of Contents
Related Manuals for Emerson EWV603
Summary of Contents for Emerson EWV603
-
Page 1: Before Using Your Vcr
3) Press the PLAY button once. 4) After a few seconds, press the PLAY button on the VCR for 3 seconds. • The RF output channel will change to channel 4 from channel 3 and you will see a playback picture. -
Page 2: Important Safeguards
2. Important Safeguards TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, WARNING: DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC CAUTION SHOCK, DO NOT REMOVE COVER (OR BACK). RISK OF ELECTRIC SHOCK NO USER SERVICEABLE PARTS INSIDE. -
Page 3: Preset For Use
1) Press the MENU button until the main Do you connect the cable of the cable box or menu appears. the satellite box to the VCR’s ANT IN jack? 2) Select "LANGUAGE SELECT" by pressing the PLAY or STOP button. Then, press the Press the MENU F.FWD button. -
Page 4: Troubleshooting Guide
TV programs cannot be seen nor- • Re-check the ANT. IN and ANT. OUT connections. See page 1. mally. • Press the VCR/TV button on the remote control so that the VCR/TV indicator on the VCR disappears. No VCR operation from the •... -
Page 5: Other Operations
EJECT STOP EJECT • If you have connected the VCR to a cable box or satellite box, refer to “Hint for Cable Box or Satellite Box” section on page 1. To cue or review picture during play- back (Picture Search) POWER Press the F.FWD or REW button. -
Page 6: Recording Features
VCR power will be turned off. The TIMER indicator will flash. • If a tape is not in the VCR or does not have the record tab, the TIMER indicator flashes and timer recording cannot be performed. Please insert a recordable tape. -
Page 7: Special Features
• These functions are not available during recording. • Press the STOP button to stop the search. • If the end of the tape is reached during a Search, the VCR will cancel the search and rewind the tape. Auto Repeat You can repeat playback of a whole tape automatically. -
Page 8: Limited Warranty
NOTICE. For information about your product, or for defaced or missing. This EMERSON Limited warran- information on how to exchange or repair ty applies only to product purchased and used in the your product, telephone or write to the fol- United States.