HP StorageWorks 2/140 - Director Switch Installation Instructions Manual
Rack mount kit
Hide thumbs
Also See for StorageWorks 2/140 - Director Switch:
- Service manual (396 pages) ,
- Product manager manual (244 pages) ,
- Installation manual (128 pages)
Table of Contents
Quick Links
See also:
Service Manual, Instructions
Table of Contents
Related Manuals for HP StorageWorks 2/140 - Director Switch
Summary of Contents for HP StorageWorks 2/140 - Director Switch
- Page 1 hp StorageWorks director 2/140 rack mount kit installation instructions Part Number: AA-RTDDB-TE/958-000280-001 Second Edition (January 2003) These installation instructions provide the procedures used for installing an HP StorageWorks Director 2/140 in an appropriate rack.
- Page 2 © Hewlett-Packard Company, 2003. All rights reserved. Hewlett-Packard Company makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
-
Page 3: Table Of Contents
Contents About this Guide Intended Audience ............iii Related Documentation . -
Page 5: About This Guide
About this Guide These installation instructions provide information to help you: • Install the HP StorageWorks™ Director 2/140 in an appropriate rack. • Perform the power-on self test. • Contact technical support for additional assistance. Intended Audience This book is intended for use by technicians who are experienced with: •... -
Page 6: Document Conventions
About this Guide Document Conventions The conventions included in Table 1 apply. Table 1: Document Conventions Element Convention Cross-reference links Blue text: Figure 1 Key names, menu items, buttons, and Bold dialog box titles File names, application names, and text Italics emphasis User input, command names, system... -
Page 7: Symbols On Equipment
About this Guide Symbols on Equipment Any enclosed surface or area of the equipment marked with these symbols indicates the presence of electrical shock hazards. Enclosed area contains no operator serviceable parts. WARNING: To reduce the risk of injury from electrical shock hazards, do not open this enclosure. -
Page 8: Rack Stability
About this Guide Rack Stability WARNING: To reduce the risk of personal injury or damage to the equipment, be sure that: • The leveling jacks are extended to the floor. • The full weight of the rack rests on the leveling jacks. •... -
Page 9: Hp Website
About this Guide HP Website The HP website has the latest information on this product, as well as the latest drivers. http://thenew.hp.com/country/us/eng/prodserv/storage.html. Access storage at: From this website, select the appropriate product or solution. HP Authorized Reseller For the name of your nearest HP Authorized Reseller: •... -
Page 11: Installation Instructions
Installation Instructions This section describes the procedures used for installing a StorageWorks Director 2/140 in an appropriate HP, or comparable, 19-inch Electronic Industries Association (EIA) rack: • HP 9000 series, 10000 series and 11000 series racks • HP rack system/e or 19-inch EIA rack Rack Mount Kit Checklist This section describes the contents of the rack mount kit as well as tools or equipment required to complete the installation. -
Page 12: Brackets
Installation Instructions Brackets Brackets and rails included in the kit are shown in Figure 1: 1 Two (2) rear mounting brackets 2 Four (4) angle mounting brackets (small) 3 Two (2) shelf brackets 4 Two (2) rear mounting plates 5 Two (2) front mounting brackets Figure 1: Brackets included in kit director 2/140 rack mount kit installation instructions... -
Page 13: Required Items
Installation Instructions Required Items Check that the following items are available before beginning the installation. • #2 Phillips screwdriver • Lift device (recommended) Rack Mounting Guidelines This section describes guidelines for installing more than one Director and positioning the Director 2/140 on the lift device. Tips for Installing More than One Switch Review the following tips: •... -
Page 14: Moving The Director 2/140
Installation Instructions Moving the Director 2/140 Use these steps to position the Director 2/140 next to the rack. WARNING: Two people will need to work together to transfer the Director 2/140 to the lift. Make sure the wheels of the lift cannot roll as you transfer the Director 2/140 to the lift. - Page 15 Installation Instructions 3. Use a straight edge to locate the corresponding rack hole along the interior vertical rails of the rack cabinet. Mark this location on each interior vertical rail. 4. Position a small angle bracket along the interior vertical rail as shown in Figure 2. Align the angle bracket so that the two threaded holes on the small tab align with the 1U location marked in step...
- Page 16 Installation Instructions 7. Attach two shelf brackets to the angle brackets on each side of the cabinet using eight pan head screws and a #2 Phillips head screwdriver as shown in Figure 3. NOTE: Center each shelf bracket between the interior vertical rails of the rack cabinet. Figure 3: Shelf brackets mounted in HP 9000, 10000 and 11000 series rack 8.
-
Page 17: Installing Shelf Brackets In An Hp Rack System/E Or 19-Inch Eia Rack
Installation Instructions Installing Shelf Brackets in an HP Rack System/e or 19-inch EIA Rack The shelf brackets mount directly to the interior vertical rails of the HP rack system/e or 19-inch EIA rack using cage nuts and Phillips panhead screws. Use these steps to install the two shelf brackets in an HP rack system/e or 19-inch EIA rack. -
Page 18: Attaching The Mounting Hardware To The Director 2/140
Installation Instructions Attaching the Mounting Hardware to the Director 2/140 Use these steps to secure the mounting hardware to the Director 2/140. NOTE: All mounting brackets are attached to the Director 2/140 using 10/32 x 3/8-inch flathead countersunk Phillips screws. 1. -
Page 19: Inserting Cage Nuts In The Rack
Installation Instructions Inserting Cage Nuts in the Rack Before placing the Director into the rack, insert the cage nuts into the appropriate locations along the exterior vertical rack rails. Read the following sections for instructions on inserting front and rear cage nuts in the rack. Inserting the Front Cage Nuts in the Rack Use these steps to insert the six supplied cage nuts in the rack’s front rails. -
Page 20: Installing The Director 2/140 In The Rack
Installation Instructions Installing the Director 2/140 in the Rack Use these steps to maneuver the Director 2/140 into the rack: 1. Using a lift device, position the Director 2/140 at the front of the cabinet. 2. If necessary, adjust the lift height so that the bottom of the Director 2/140 is parallel with the shelf mounts in the rack. -
Page 21: Connecting The Director 2/140 To A Power Source
Installation Instructions Connecting the Director 2/140 to a Power Source The Director 2/140 includes two power supplies (labeled PS0 and PS1 on the rear of the unit) for redundancy. Each power supply must be connected to an appropriate power source that provides 220-volt AC power. The Director 2/140 is shipped with the following power cords: •... -
Page 22: Power-On Self Test
Installation Instructions Power-On Self Test Once the Director 2/140 is connected to a power source, a Power-On Self Test (POST) is initiated. The following sequence of events occur during the POST: 1. Amber LEDs on both CTP cards and all FPM cards illuminate momentarily. 2.