Page 1 Projector CP-X2015WN/CP-X2515WN/CP-X3015WN/ CP-X4015WN/CP-WX2515WN/CP-WX3015WN User's Manual (detailed) Operating Guide Thank you for purchasing this projector. WARNING ►Before using this product, please read all manuals for this product. Be sure to read Safety Guide ﬁrst. After reading them, store them in a safe place for future reference.
Page 2 Read this Safety Guide first. Projector User's Manual - Safety Guide Thank you for purchasing this projector. WARNING • Before using, read these user's manuals of this projector to ensure correct usage through understanding. After reading, store them in a safe place for future reference.
Page 3: Safety Precautions
Safety Precautions WARNING Never use the projector if a problem should occur. Abnormal operations such as smoke, strange odor, no image, no sound, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc. can cause a fire or electrical shock. In such case, immediately turn off the power switch and then disconnect the power plug from the power outlet.
Page 4 Safety Precautions (continued) WARNING Be cautious of High temperatures of the projector. High temperatures are generated when the lamp is lit. It could result in fire or burn. Use special caution in households where children are present. Do not touch about the lens, air fans and ventilation openings during use or immediately after use, to prevent a burn.
Page 5 Safety Precautions (continued) WARNING Be careful in handling the light source lamp. The projector uses a high-pressure mercury glass lamp made of glass. The lamp can break with a loud bang, or burn out. When the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and for gas containing mercury to escape from the projector’s vent holes.
Page 6 Safety Precautions (continued) CAUTION Be careful in moving the projector. Neglect could result in an injury or damage. • Do not move the projector during use. Before moving, disconnect the power cord and all external connections, and close the slide lens door or attach the lens cap.
Page 7 Safety Precautions (continued) CAUTION Remove the power cord for complete separation. • For safety purposes, disconnect the power cord if the projector is not to be used for prolonged periods of time. Disconnect the • Before cleaning, turn off and unplug the projector. Neglect could result in plug from the fire or electrical shock.
Page 8 Safety Precautions (continued) NOTE About consumables. Lamp, LCD panels, polarizors and other optical components, and air filter and cooling fans have a different lifetime in each. These parts may need to be replaced after a long usage time. • This product isn’t designed for continuous use of long time. In the case of continuous use for 6 hours or more, or use for 6 hours or more every day (even if it isn’t continuous), or repetitious use, the lifetime may be shortened, and these parts may need to be replaced even if one year has not passed since the beginning of using.
Page 9 Lamp WARNING HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them.
Page 10 Regulatory Notices FCC Statement Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Page 11: Table Of Contents
Contents Introduction ....3 SETUP menu ....46 Features ..... . 3 UTO KEYSTONE EYSTONE UTO ECO MODE...
Page 12: Introduction
Introduction Introduction Features The projector provides you with the broad use by the following features. This projector has a variety of I/O ports that supposedly cover for any business scene. The HDMI port can support various image equipment which have digital interface to get clearer pictures on a screen. If you insert a USB storage device, such as a USB memory, into the USB TYPE A port and select the port as the input source, you can view images stored in the device.
Page 13: Part Names
Introduction Part names (11) (12) 108) (1) Lamp cover ( The lamp unit is inside. 23, 49) (2) Speaker ( 110) (3) Filter cover ( The air ﬁlter and intake vent are inside. (4) Elevator feet (x2) ( (5) Elevator buttons (x2) ( (6) Remote sensor ( 112) (7) Lens (...
Page 14 Introduction Part names (continued) Control panel (1) STANDBY/ON button ( (2) INPUT button ( (3) MENU button ( 115) (4) LAMP indicator ( 115) (5) TEMP indicator ( 115) (6) POWER indicator ( 10 ~ 15) Rear panel ( (1) LAN port (11) COMPUTER IN2 port (2) USB TYPE A port(x2) (12) MONITOR OUT port...
Page 15 Introduction Part names (continued) Remote control (10) (1) VIDEO button ( COMPUTER MY SOURCE/ VIDEO DOC.CAMERA (2) COMPUTER button ( ASPECT AUTO SEARCH BLANK (3) SEARCH button ( (16) (12) FREEZE MAGNIFY PAGE VOLUME (4) STANDBY/ON button ( (14) DOWN (11) (5) ASPECT button ( MY BUTTON...
Page 16: Setting Up
Setting up Setting up Install the projector according to the environment and manner the projector will be used in. For the case of installation in a special state such as ceiling mount, the speciﬁed mounting accessories ( Speciﬁcations in the User’s Manual (concise)) and service may be required.
Page 17 Setting up Arrangement (continued) WARNING ►Install the projector where you can access the power outlet easily. If an abnormality should occur, unplug the projector urgently. Otherwise it could cause a ﬁre or electric shock. ►Do not subject the projector to unstable conditions. If the projector falls or topples over, it could result in injury or damage to the projector and the surrounding things.
Page 18 Setting up Arrangement (continued) CAUTION ►Place the projector in a cool place with sufﬁcient ventilation. The projector may shutdown automatically or may malfunction if its internal temperature is too high. Using a damaged projector could result in a ﬁre and an electric shock. •...
Page 19: Connecting With Your Devices
Setting up Connecting with your devices Before connecting the projector to a device, consult the manual of the device to conﬁrm that the device is suitable for connecting with this projector and prepare the required accessories, such as a cable in accord with the signal of the device. Consult your dealer when the required accessory did not come with the product or the accessory is damaged.
Page 20 Setting up Connecting with your devices (continued) About Plug-and-Play capability • Plug-and-Play is a system composed of a computer, its operating system and peripheral equipment (i.e. display devices). This projector is VESA DDC 2B compatible. Plug-and-Play can be used by connecting this projector to a computer that is VESA DDC (display data channel) compatible.
Page 21 Setting up Connecting with your devices (continued) Computer AUDIO IN AUDIO OUT NOTE • Before connecting the projector to a computer, consult the computer’s manual and check the compatibility of the signal level, the synchronization methods and the display resolution output to the projector. - Some signal may need an adapter to input this projector.
Page 22 Setting up Connecting with your devices (continued) Computer External device Access point wireless adapter (optional) AUDIO IN AUDIO OUT storage device CAUTION ► Before connecting the projector to a network system be sure to obtain the consent of the administrator of the network. ►Do not connect the LAN port to any network that might have the excessive voltage.
Page 23 Setting up Connecting with your devices (continued) VCR/DVD/Blu-ray Disc player AUDIO IN AUDIO OUT • The HDMI port of this model is compatible with HDCP (High-band- NOTE width Digital Content Protection) and therefore capable of displaying a video signal from HDCP compatible DVD players or the like. - The HDMI supports the following signals.
Page 24 Setting up Connecting with your devices (continued) Speakers Monitor (with an ampliﬁ er) AUDIO IN AUDIO OUT NOTE • If a loud feedback noise is produced from the speaker, move the microphone away from the speaker. Microphone function • You can connect a dynamic microphone to the MIC port with a 3.5 mm mini-plug. In that case, the built-in speaker outputs the sound from the microphone, even while the sound from the projector is output.
Page 25: Connecting To A Power Supply
Setting up Connecting to a power supply Put the connector of the power cord into the AC IN (AC inlet) of the projector. Firmly plug the power cord’s plug into the outlet. In a couple of seconds after the AC IN power supply connection, the POWER indicator will light up in steady orange.
Page 26: Fastening The Adapter Cover
Setting up Fastening the adapter cover Use the supplied adapter cover to prevent the USB wireless adapter from coming off easily. Loosen the screw (marked with triangle) on the bottom left of the USB TYPE A port. Insert the tab of the cover into the hole at the upper right of the USB TYPE A port in the direction of the arrow.
Page 27: Remote Control
Holding the hook part of the battery cover, remove it. Align and insert the two AA batteries (HITACHI MAXELL or HITACHI MAXELL ENERGY, Part No.LR6 or R6P) according to their plus and minus terminals as indicated in the remote control.
Page 28: About The Remote Control Signal
Remote control About the remote control signal The remote control works with the projector’s remote sensor. This projector has a remote sensor on the front. The sensor senses the signal within the following range when the sensor is active: 60 degrees (30 degrees to the left and right of the sensor) (approx.) within 3 meters about.
Page 29: Using As A Simple Pc Mouse & Keyboard
Remote control Using as a simple PC mouse & keyboard The accessory remote control works as a simple mouse and keyboard of the computer, when the projector’s USB TYPE B port and the computer’s type A USB port are connected. (1) PAGE UP key: Press PAGE UP button.
Page 30: Power On/Off
Power on/off Power on/off STANDBY/ON button Turning on the power POWER indicator Make sure that the power cord is ﬁrmly and correctly connected to the projector and the outlet. Make sure that the POWER indicator is 115). Then remove the steady orange ( lens cover.
Page 31: Turning Off The Power
Power on/off Turning off the power Press the STANDBY/ON button on the projector or the remote control. The message “Power off?” will appear on the screen for about 5 seconds. Press the STANDBY/ON button again while the message appears. The projector lamp will go off, and the POWER indicator will begin blinking in orange.
Page 32: Operating
Operating Operating VOLUME +/- button Adjusting the volume Use the VOLUME +/VOLUME - buttons to adjust the volume. VIDEO COMPUTER MY SOURCE/ DOC.CAMERA A dialog will appear on the screen to aid you in adjusting the ASPECT AUTO SEARCH BLANK volume.
Page 33: Selecting An Input Signal
Operating Selecting an input signal INPUT Press INPUT button on the projector. button Each time you press the button, the projector switches its input port from the current port as below. COMPUTER IN1 COMPUTER IN2 VIDEO USB TYPE A S-VIDEO USB TYPE B HDMI 56), the...
Page 34: Searching An Input Signal
Operating Selecting an input signal(continued) MY SOURCE / Press the MY SOURCE / DOC. CAMERA button on DOC. CAMERA button the remote control. The input signal will be changed 59). into the signal you set as MY SOURCE ( VIDEO COMPUTER MY SOURCE/ DOC.CAMERA ●...
Page 35: Selecting An Aspect Ratio
Operating Selecting an aspect ratio Press ASPECT button on the remote control. ASPECT button Each time you press the button, the projector switches the mode for aspect ratio in turn. VIDEO COMPUTER MY SOURCE/ DOC.CAMERA For a computer signal ASPECT AUTO SEARCH BLANK...
Page 36: Adjusting The Projector's Elevator
Operating Adjusting the projector’s elevator When the place to put the projector is slightly uneven to the left or right, use the elevator feet to place the projector horizontally. 14° Using the feet can also tilt the projector in order to project at a suitable angle to the screen, elevating the front side of the projector within 14 degrees.
Page 37: Using The Automatic Adjustment Feature
Operating Using the automatic adjustment feature AUTO button Press AUTO button on the remote control. Pressing this button performs the following. VIDEO COMPUTER MY SOURCE/ DOC.CAMERA For a computer signal ASPECT AUTO SEARCH BLANK The vertical position, the horizontal position and the horizontal MAGNIFY FREEZE PAGE...
Page 38: Correcting The Keystone Distortions
Operating KEYSTONE button Correcting the keystone distortions Press KEYSTONE button on the remote COMPUTER MY SOURCE/ VIDEO DOC.CAMERA control. A dialog will appear on the screen ASPECT AUTO SEARCH BLANK to aid you in correcting the distortion. MAGNIFY FREEZE PAGE VOLUME DOWN Use the ▲/▼...
Page 39: Using The Magnify Feature
Operating MAGNIFY Using the magnify feature ON/OFF button Press the MAGNIFY ON button on the remote control. VIDEO COMPUTER MY SOURCE/ The picture will be magniﬁ ed, and the MAGNIFY dialog DOC.CAMERA will appear on the screen. When the MAGNIFY ASPECT AUTO SEARCH...
Page 40: Temporarily Freezing The Screen
Operating Temporarily freezing the screen FREEZE button Press the FREEZE button on the remote control. COMPUTER MY SOURCE/ VIDEO The “FREEZE” indication will appear on the screen (however, DOC.CAMERA the indication will not appear when the OFF is selected for ASPECT AUTO SEARCH...
Page 41: Using The Menu Function
Operating Using the menu function This projector has the following menus: PICTURE, IMAGE, INPUT, SETUP, AUDIO, SCREEN, OPTION, NETWORK, SECURITY and EASY MENU. EASY MENU consists of functions often used, and the other menus are classiﬁed into each purpose and brought together as the ADVANCED MENU. Each of these menus is operated using the same methods.
Page 42 Operating Using the menu function (continued) To close the MENU, press the MENU button again or select EXIT and press the ◄ cursor button or ENTER button. Even if you do not do anything, the dialog will automatically disappear after about 30 seconds. ●...
Page 43: Easy Menu
EASY MENU EASY MENU From the EASY MENU, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons. Then perform it according to the following table. Item Description Using the ◄/► buttons switches the mode for aspect ratio. ASPECT 39).
Page 44: Advanced Menu , Exit
EASY MENU Item Description Using the ◄/► buttons switches the ECO MODE. ECO MODE 47). See the ECO MODE item in SETUP menu ( Pressing the ► button displays the INSTALLATION dialog. INSTALLATION 47). See the INSTALLATION item in SETUP menu ( Performing this item resets all of the EASY MENU items except the FILTER TIME and LANGUAGE.
Page 45: Picture Menu
PICTURE menu PICTURE menu From the PICTURE menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.
Page 46 PICTURE menu Item Description Using the ▲/▼ buttons switches the color temperature mode. To adjust CUSTOM Selecting a mode whose name includes CUSTOM and then pressing the ► button or the ENTER button displays a dialog to aid you in adjusting the OFFSET and GAIN of the selected mode.
Page 47 PICTURE menu Item Description Using the ◄/► buttons adjusts the sharpness. Weak Strong SHARPNESS • There may be some noise and/or the screen may ﬂicker for a moment when an adjustment is made. This is not a malfunction. Using the ▲/▼ cursor buttons changes the active iris control mode. PRESENTATION THEATER PRESENTATION : The active iris displays the best presentation...
Page 48: Image Menu
IMAGE menu IMAGE menu From the IMAGE menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.
Page 49 IMAGE menu Item Description Using the ◄/► buttons adjusts the over-scan ratio. Small (It magniﬁes picture) Large (It reduces picture) • This item can be selected only for a video, s-video and component video signal. • For an HDMI signal, this item can also be selected if either (1) or OVER SCAN (2) applies.
Page 50 IMAGE menu Item Description Using the ◄/► buttons adjusts the horizontal phase to eliminate ﬂicker. Right Left H PHASE • This item can be selected only for a computer signal or a component video signal. This function is unavailable for a signal from the LAN, USB TYPE A, USB TYPE B or HDMI port.
Page 51: Input Menu
INPUT menu INPUT menu From the INPUT menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.
Page 52 INPUT menu Item Description The video format for S-VIDEO port and VIDEO port can be set. (1) Use the ▲/▼ buttons to select the input port. (2) Using the ◄/► buttons switches the mode for video format. AUTO NTSC SECAM VIDEO FORMAT N-PAL M-PAL...
Page 53 INPUT menu Item Description The computer input signal type for COMPUTER IN1 and IN2 ports can be set. (1) Use the ▲/▼ buttons to select the COMPUTER IN port to be set. (2) Use the ◄/► buttons to select the computer input signal type. AUTO SYNC ON G OFF COMPUTER IN...
Page 54 INPUT menu Item Description The resolution for the COMPUTER IN1 and COMPUTER IN2 input signals can be set on this projector. (1) In the INPUT menu select the RESOLUTION using the ▲/▼ buttons and press the ► button. The RESOLUTION menu will be displayed.
Page 55: Setup Menu
SETUP menu SETUP menu From the SETUP menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.
Page 56 SETUP menu Item Description Using the ▲/▼ buttons turns on/off the AUTO ECO MODE. • When ON is selected, the projector will always be set to Eco mode AUTO ECO MODE below) setting. An OSD at start-up regardless of the ECO MODE ( message “AUTO ECO MODE”...
Page 57: Monitor Out
SETUP menu Item Description Using ▲/▼ buttons switches the standby mode setting between NORMAL and SAVING. NORMAL SAVING When SAVING is selected, the power consumption in the standby mode is lowered with some functional restriction as below: • When SAVING is selected, the RS-232C communication control except to turn the projector on and the network function are disabled while the projector is in the standby mode.
Page 58: Audio Menu
AUDIO menu AUDIO menu From the AUDIO menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or the ENTER button to execute the item. Then perform it according to the following table.
Page 59: Screen Menu
SCREEN menu SCREEN menu From the SCREEN menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.
Page 60 SCREEN menu Item Description This item allows you to capture an image for use as a MyScreen image which can be used as the BLANK screen and START UP screen. Display the image you want to capture before executing the following procedure.
Page 61 SCREEN menu Item Description Using the ▲/▼ buttons turns on/off the MyScreen lock function. When the ON is selected, the item MyScreen is locked. Use this MyScreen Lock function for protecting the current MyScreen. • This function cannot be selected when the ON is selected to the 79).
Page 62: Ource Name
SCREEN menu Item Description Each input port for this projector can have a name applied to it. (1) Use the ▲/▼ buttons on the SCREEN menu to select SOURCE NAME and press the ► or ENTER button. The SOURCE NAME menu will be displayed. (2) Use the ▲/▼...
Page 63 SCREEN menu Item Description (6) The current name will be displayed on the ﬁrst line. Use the ▲/▼/◄/► buttons and the ENTER or INPUT button to select and enter characters. To erase 1 character at one time, press the RESET button or press the ◄...
Page 64 SCREEN menu Item Description The C.C. is the function that displays a transcript or dialog of the audio portion of a video, ﬁles or other presentation or other relevant sounds. It is required to have NTSC format video or 480i@60 format component video source supporting C.C.
Page 65: Option Menu
OPTION menu OPTION menu From the OPTION menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item, except for the items LAMP TIME and FILTER TIME.
Page 66 OPTION menu Item Description Using the ▲/▼ buttons adjusts the time to count down to automatically turn the projector off. Long (max. 99 minutes) Short (min. 0 minute = DISABLE) When the time is set to 0, the projector is not turned off automatically. AUTO POWER When the time is set to 1 to 99, and when the passed time with no-signal or an unsuitable signal reaches at the set time, the...
Page 67 OPTION menu Item Description This item is to assign one of the following functions to MY BUTTON 1/2 on the remote control ( (1) Use the ▲/▼ buttons on the MY BUTTON menu to select a MY BUTTON - (1/2) and press the ► or ENTER button to display the MY BUTTON setup dialog.
Page 68 OPTION menu Item Description • ACTIVE IRIS: Changes the active iris mode. 34). • PICTURE MODE: Changes the PICTURE MODE ( 57). • FILTER RESET: Displays the ﬁlter time reset conﬁrmation dialogue ( • TEMPLATE: Makes the template pattern selected to the 54) appear or disappear.
Page 69 OPTION menu Item Description AUTO ADJUST Using the ▲/▼ buttons to select one of the mode. When the DISABLE is selected, the automatic adjustment feature is disabled. FINE FAST DISABLE FINE: Finer tuning including H.SIZE adjustment. FAST: Faster tuning, setting H.SIZE to prearranged data for the input signal.
Page 70 OPTION menu Item Description REMOTE FREQ. (1) Use the ▲/▼ button to change the projector's remote sensor 19). frequency setting ( 1:NORMAL 2:HIGH (2) Use the ◄/► button to change the projector's remote sensor on or off. The factory default setting is for both 1:NORMAL and 2:HIGH to be on. If the remote control does not function correctly, disable either of them.
Page 71 OPTION menu Item Description COMMUNICATION TYPE Select the communication type for transmission via the CONTROL port. NETWORK BRIDGE: Select this type, if it is required to control an external device as a network terminal, via this projector from the computer. The CONTROL port doesn't accept RS-232C commands (Network Bridge Function in the Network Guide)
Page 72 OPTION menu Item Description RESPONSE LIMIT TIME Select the time period to wait for receiving response data from other device communicating by the NETWORK BRIDGE and the HALF-DUPLEX through the CONTROL port. OFF: Select this mode if it is not required to check the responses from the device that the projector sends data to.
Page 73 OPTION menu Item Description The following items are exempted. OPTION: LAMP TIME, FILTER TIME, SERVICE(GHOST) NETWORK: WIRELESS AND WIRED SETUP (IP ADDRESS, SUBNET MASK, DEFAULT GATEWAY, DATE AND TIME), MY IMAGE, PRESENTATION SECURITY: MY TEXT DISPLAY • Operation is not available if SECURITY_ CLONNING LOCK is turned ON.
Page 74 OPTION menu Item Description Load MyScreen data • Please save the image data as "pj_logo.bmp" or "pj_logo.gif" into USB memory. • Please note that the only compatible formats are as follows. -File format Windows BMP bit/pixel: 2/4/8/15/16/24/32bit Compression format : Without compression/RLE -Image size: more than 36x36, less than 1280x800 •...
Page 75 OPTION menu Item Description INFORMATION Selecting this item displays a dialog titled “INPUT_INFORMATION”. It shows the information about the current input. • The “FRAME LOCK” message on the dialog means the frame lock function is working. • This item can't be selected for no signal and sync out. SERVICE •...
Page 76: Network Menu
NETWORK menu NETWORK menu Remember that incorrect network settings on this projector may cause trouble on the network. Be sure to consult with your network administrator before connecting to an existing access point on your network. Select “NETWORK” from the main menu to access the following functions.
Page 77 NETWORK menu Item Description Use the ▲/▼ buttons to turn DHCP on/off. Select OFF when the network does not have DHCP DHCP enabled. To save the setting, press the ► button. (Dynamic Host • When the “DHCP” setting changes to “ON”, it Conﬁguration takes a little time to obtain IP address from DHCP Protocol)
Page 78 NETWORK menu Item Description Use the ▲/▼/◄/► buttons to enter the Year (last two digits), Month, Date, Hour and Minute. • When this item is set, the same item in the WIRED SETUP menu is overwritten with the same 73). setting ( •...
Page 79 NETWORK menu Item Description Use the ▲/▼ buttons to select the SSID to display the SSID menu. #1 DEFAULT #2 DEFAULT #3 DEFAULT #5 CUSTOM #4 DEFAULT Select one of the DEFAULT (#1~#4) and press ► or ENTER button. To adjust CUSTOM Press the ►...
Page 80 NETWORK menu Item Description "Selecting this item displays the WIRELESS_INFORMATION dialog for viewing the wireless LAN settings." Use the ▲/▼ buttons to switch the page. The ﬁrst page shows the wireless LAN settings. The second and subsequent pages display the signal information of wireless LAN connection devices.
Page 81 NETWORK menu Item Description Selecting this item displays the WIRED SETUP menu for the wired LAN. Use the ▲/▼ buttons to select an item, and the ► or ENTER button on the remote control to perform the item. Use the ▲/▼ buttons to turn DHCP on/off. Select OFF when the network does not have DHCP enabled.
Page 82 NETWORK menu Item Description Use the ▲/▼ buttons to enter the TIME DIFFERENCE. Set the same TIME DIFFERENCE as the one set on your computer. If unsure, consult your IT manager. TIME Use the ► button to return to the menu after DIFFERENCE setting the TIME DIFFERENCE.
Page 83 NETWORK menu Item Description (1) Use the ▲/▼ buttons on the NETWORK menu to select the PROJECTOR NAME and press the ► button. The PROJECTOR NAME dialog will be displayed. (2) The current PROJECTOR NAME will be displayed on the ﬁrst 3 lines.
Page 84 Use the application to transfer the im- age data. It can be downloaded from the Hitachi web site. Use the ▲/▼ buttons to select an item which is a still image by the MY IMAGE (My Image Function in the Network Guide) and the ►...
Page 85 It can be installed from the bundled application CD. You can also download the latest version and relevant information from the Hitachi website (http://www.hitachi-america.us/digitalmedia or http://www.hitachidigitalmedia.com).For details of Network Presentation and instructions to install the "LiveViewer", refer to the manual for "LiveViewer".
Page 86 NETWORK menu Item Description • To change from Single PC mode to Multi PC mode, press ► button to choose OK in the dialog and press the ENTER or INPUT button. The display mode is changed. • For details on how to switch the display mode to Multi PC mode on your computer, refer to the MULTI PC...
Page 87: Security Menu
SECURITY menu SECURITY menu This projector is equipped with security functions. From the SECURITY menu, items shown in the table below can be performed. To use SECURITY menu: User registration is required before using the security functions. Enter to the SECURITY menu 1.
Page 88 SECURITY menu Item Description The MyScreen PASSWORD function can be used to prohibit access to the MyScreen function and prevent the currently registered MyScreen image from being overwritten. 1 Turning on the MyScreen PASSWORD 1-1 Use the ▲/▼ buttons on the SECURITY menu to select MyScreen PASSWORD and press the ►...
Page 89 SECURITY menu Item Description PIN LOCK is a function which prevents the projector from being used unless a registered Code is input. 1 Turning on the PIN LOCK 1-1 Use the ▲/▼ buttons on the SECURITY menu to select PIN LOCK and press the ► button or the ENTER button to display the PIN LOCK on/off menu.
Page 90: Transition Detector
SECURITY menu Item Description If this function is set to ON and the vertical angle of the projector or the INSTALLATION setting is different from the previous recorded setting, the TRANSITION DETECTOR ON alarm will be displayed and the input signal will not be displayed.
Page 91 SECURITY menu Item Description The MY TEXT PASSWORD function can prevent the MY TEXT from being overwritten. When the password is set for the MY TEXT; • The MY TEXT DISPLAY menu will be unavailable, which can prohibit changing the DISPLAY setting. •...
Page 92: M Y Text Display , M
SECURITY menu Item Description (1) Use the ▲/▼ buttons on the SECURITY menu to select the MY TEXT DISPLAY and press the ► or ENTER button to display the MY TEXT DISPLAY on/off menu. (2) Use the ▲/▼ buttons on the MY TEXT DISPLAY on/off menu to select on or off.
Page 93: Presentation Tools
Presentation tools Presentation tools The projector has the following two convenient tools that enable on-screen presentations easily and quickly: below) - PC-LESS Presentation ( - Drawing function Drawing function enables you to draw on the projector’s screen with USBmouse or tablets connected to the USB TYPE A ports. For details of Drawing function, refer to the Operating Guide - Drawing function.
Page 94 Presentation tools PC-LESS Presentation (continued) [Supported ﬁle format and its extension] • JPEG (.jpeg, .jpg) * Progressive is not supported. • Bitmap (.bmp) * 16bit mode and compressed bitmap is not supported. • PNG (.png) * Interlace PNG is not supported. •...
Page 95 Presentation tools PC-LESS Presentation (continued) Operating by buttons or keys You can control the images on the Thumbnail screen with the remote control, control panel or Web Remote Control. The following functions can be supported while the Thumbnail is displayed. Button operation Functions Web Remote...
Page 96 Presentation tools PC-LESS Presentation (continued) Operating by the menu on the Thumbnail screen You can also control the images by using the menu on the Thumbnail screen. Item Functions Moves to an upper folder. SORT Allows you to sort ﬁles and folders as following. Press the ►...
Page 97 Presentation tools PC-LESS Presentation (continued) NOTE • These operations are not accessible while the projector OSD is displayed. • The Thumbnail mode is able to display up to 20 ﬁles in one page. • It is not possible to change the input port by using the INPUT button when the Thumbnail screen, Slideshow, or Full Screen is displayed.
Page 98 Presentation tools PC-LESS Presentation (continued) Full Screen Mode The Full Screen mode shows a full display image. To display in Full Screen mode, select an image in the Thumbnail screen. Then press the ENTER button on the remote control, the INPUT button on the control panel or click [ENTER] on the Web Remote Control.
Page 99 Presentation tools PC-LESS Presentation (continued) Operations for movie A remote control icon and a progress bar are displayed when one of the cursor buttons, ENTER button or INPUT button on the remote control, control panel or Web Remote Control is pressed or clicked while a movie is playing in the Full Screen mode.
Page 100 Presentation tools PC-LESS Presentation (continued) Slideshow mode The Slideshow mode displays images in full screen and switches the images at 87). intervals set in INTERVAL on the Thumbnail screen menu ( You can start this function from the Slideshow menu. To display the Slideshow menu, select the SLIDESHOW button in the Thumbnail mode and press the ENTER button on the remote control, INPUT button on the control panel, or click [ENTER] on the Web Remote Control.
Page 101 Presentation tools PC-LESS Presentation (continued) You can play the Slideshow at your desired conﬁguration. Conﬁgure the Slideshow items in the Thumbnail. 1) RETURN : Returns to the thumbnail mode. 2) PLAY : Play the Slideshow. 3) START : Set the beginning number of the Slideshow.
Page 102 Presentation tools PC-LESS Presentation (continued) Playlist The Playlist is a DOS format text ﬁle, which decides the order of displayed still image ﬁles in the Thumbnail or Slideshow. The playlist ﬁle name is “playlist.txt” and it can be edited on a computer. It is created in the folder that contains the selected image ﬁles when the PC-LESS Presentation is started or the Slideshow is conﬁgured.
Page 103: Drawing Function
Presentation tools Drawing Function Main Functions This function is an interactive tool for use with Hitachi projectors; it offers effective features for making classroom and business presentations more fun and easier to understand. Drawing on projected images You can draw pictures or text on images projected by our projectors.
Page 104 • Some USB memory devices and/or USB hubs may not operate properly. Connecting the Computer and Projector with a USB Cable In order to use the Hitachi Pen tablet (ex. TB-1)/USB mouse in place of the computer’s mouse, connect a USB TYPE B port of the projector with a USB port (Type A) of the computer with a USB cable.
Page 105 Presentation tools Drawing Function (continued) Wireless USB memory adapter device Tablet Computer USB TYPE A USB TYPE A USB TYPE B Projector Fig.2 Example of connections Wireless USB memory adapter device Mouse USB hub Computer Tablet USB TYPE B USB TYPE A USB TYPE A Projector Fig.3 Example of connections...
Page 106 • The drawing function does not support drawing on images from the LAN port or the USB TYPE B port of the projector. If you operate the Hitachi Pen tablet (ex. TB-1)/USB mouse while these images are displayed, the input source may automatically switch to USB TYPE A port.
Page 107 Presentation tools Using the Drawing Function (continued) 5. Erase Erases all the lines drawn with the pen. Projector Operates the projector. Operation Calls up and display the previous ﬁ le in the USB memory device from that currently selected. This function is available when the projector is displaying a ﬁ...
Page 108 Presentation tools Using the Drawing Function (continued) Projector Turns off the projector. Operation Touch/click the icon for three seconds or so. (Continued) • If you turn the projector off while using the drawing function, any unsaved drawings will be lost. Toggles between display/hide the Pattern (grid lines).
Page 109: Usb Display(Windows Computer)
Presentation tools USB Display(Windows computer) 12). The projector can display images transferred from a computer via an USB cable ( Hardware and software requirement for computer • OS: One of the following. (32 bit version only) ® Windows XP Home Edition /Professional Edition ®...
Page 110 Presentation tools USB Display(Windows computer) (continued) This application will appear in the Windows notiﬁcation area once it starts. You can quit the application from your computer by selecting “Quit” on the menu. NOTE • The “LiveViewer” (refer to the Network Guide) and this application cannot be used at the same time.
Page 111 Presentation tools USB Display(Windows computer) (continued) Right-Click menu The menu shown in the right will be displayed when you right-click the application icon in the Windows notiﬁcation area. Display : The Floating menu is displayed, and the icon disappears from the Windows notiﬁcation area.
Page 112 Presentation tools USB Display(Windows computer) (continued) Options window If you select the Option button on the Floating menu, the Options window is displayed. Optimize Performance The “LiveViewer Lite for USB” captures screenshots in JPEG data and sends them to the projector. The “LiveViewer Lite for USB” has two options that have different compression rate of JPEG data.
Page 113: Usb Display(Mac Computer)
Presentation tools USB Display(Mac computer) 12). The projector can display images transferred from a computer via an USB cable ( Hardware and software requirement for computer • OS: Mac OSX 10.5(Intel) Mac OSX 10.6(Intel) Mac OSX 10.7(Intel) This application is not compatible with Power PC. •...
Page 114 Presentation tools USB Display(Mac computer) (continued) NOTE • The “LiveViewer” (refer to the Network Guide) and this application cannot be used at the same time. If you connect your computer to the projector by using a USB cable while the “LiveViewer”...
Page 115 Presentation tools USB Display(Mac computer) (continued) Menu If you select “Display” on the Right-Click menu, the Floating menu shown in the right will appear on your computer screen. q Start capture button The transmission to the projector is started and the images will be displayed. w Stop button The image transmission is stopped.
Page 116 Presentation tools USB Display(Mac computer) (continued) Options window If you select the Option button on the Floating menu, the Options window is displayed. Optimize Performance The “LiveViewer Lite for USB” captures screenshots in JPEG data and sends them to the projector. The “LiveViewer Lite for USB” has two options that have different compression rate of JPEG data.
Page 117: Maintenance
Maintenance Maintenance Replacing the lamp A lamp has ﬁnite product life. Using the lamp for long periods of time could cause the pictures darker or the color tone poor. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. Preparation of a new lamp and early replacement are recommended.
Page 118: Lamp Warning
Maintenance Replacing the lamp (continued) Lamp warning HIGH TEMPERATURE HIGH PRESSURE HIGH VOLTAGE WARNING ►The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time.
Page 119: Cleaning And Replacing The Air Filter
Maintenance Cleaning and replacing the air ﬁlter The air ﬁlter unit of this projector consists of a ﬁlter cover, two kinds of ﬁlters, and a ﬁlter frame. The new double large ﬁlters system is expected to function longer. However, please check and clean it periodically to keep ventilation needed for normal operation of the projector.
Page 120 Maintenance Cleaning and replacing the air ﬁlter (continued) Turn the projector on and reset the ﬁlter time using the FILTER TIME item in the EASY MENU. (1) Press the MENU button to display a menu. (2) Point at the FILTER TIME using the ▼/▲ button, then press the ► button. A dialog will appear.
Page 121: Other Care
Maintenance Other care Inside of the projector In order to ensure the safe use of your projector, please have it cleaned and inspected by your dealer about once every year. Caring for the lens If the lens is ﬂawed, soiled or fogged, it could cause deterioration of display quality.
Page 122: Troubleshooting
Troubleshooting Troubleshooting If an abnormal operation should occur, stop using the projector immediately. WARNING ►Never use the projector if abnormal operations such as smoke, Troubleshooting strange odor, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc. should occur. In such cases, immediately disconnect the power plug from the power outlet.
Page 123 Troubleshooting Related messages (continued) Message Description The internal temperature is rising. Please turn the power off, and allow the projector to cool down at least 20 minutes. After having conﬁrmed the following items, please turn the power ON again. • Is there blockage of the air passage aperture? •...
Page 124: Regarding The Indicator Lamps
Troubleshooting Regarding the indicator lamps When operation of the LAMP, TEMP and POWER indicators differs from usual, check and cope with it according to the following table. POWER LAMP TEMP Description indicator indicator indicator Lighting Turned Turned The projector is in a standby state. Orange Please refer to the section “Power on/off”.
Page 125 Troubleshooting Regarding the indicator lamps (continued) POWER LAMP TEMP Description indicator indicator indicator The cooling fan is not operating. Please turn the power off, and allow the projector to Blinking cool down at least 20 minutes. After the projector has Blinking Turned sufﬁciently cooled down, please make conﬁrmation...
Page 126 Troubleshooting Regarding the indicator lamps (continued) POWER LAMP TEMP Description indicator indicator indicator Blinking In At least 1 Power ON schedule is saved to the Green Turned Turned projector. approx. 3 Please refer to Schedule Settings in the Network seconds. Guide.
Page 127: Resetting All Settings
Troubleshooting Resetting all settings When it is hard to correct some wrong settings, the FACTORY RESET function of 66) can reset all settings (except settings such SERVICE item in OPTION menu ( as LANGUAGE, LAMP TIME, FILTER TIME, FILTER MESSAGE, SECURITY and NETWORK) to the factory default.
Page 128 Troubleshooting Phenomena that may be easy to be mistaken for machine defects (continued) Reference Phenomenon Cases not involving a machine defect page The signal cables are not correctly connected. 12 ~ 15 Correctly connect the audio cables. The MUTE function is working. Restore the sound pressing MUTE or VOLUME +/- button on the remote control.
Page 129 Troubleshooting Phenomena that may be easy to be mistaken for machine defects (continued) Reference Phenomenon Cases not involving a machine defect page The projector does not recognize the USB storage device inserted into USB TYPE A port. No pictures are Before removing the USB storage device, be sure to use displayed.
Page 130 Troubleshooting Phenomena that may be easy to be mistaken for machine defects (continued) Reference Phenomenon Cases not involving a machine defect page When the projector is operating in Eco mode, ﬂickering may appear on screen. Set ECO MODE to NORMAL, and set AUTO ECO Some kind MODE to OFF, in the SETUP menu.
Page 131 Troubleshooting Phenomena that may be easy to be mistaken for machine defects (continued) Reference Phenomenon Cases not involving a machine defect page The SAVING function is working. Select NORMAL for STANDBY MODE item in the SETUP menu. Schedule The internal clock has been reset. function does Once you turn off the projector in the SAVING mode or the not work...
Page 132: Speciﬁcations
Speciﬁcations Speciﬁcations Please see the Speciﬁcations in the User’s Manual (concise) which is a book. End User License Agreement for the Projector Software • Software in the projector consists of the plural number of independent software modules and there exist our copyright or/and third party copyrights for each of such software modules.
Page 133 Projector CP-X2015WN/CP-X2515WN/CP-X3015WN/ CP-X4015WN/CP-WX2515WN/CP-WX3015WN User's Manual (detailed) Network Guide Thank you for purchasing this product. This manual is intended to explain only the network function. For proper use of this product, please refer to this manual and the other manuals for this product. WARNING ►Before using this product, be sure to read all manuals for this product.
Page 134 Contents Contents Caution ..................4 1. Connection to the network ............5 1.1 System requirements ................. 5 1.1.1 Required equipment preparation ..................5 1.1.2 Hardware and software requirement for computer ............5 1.2 Manual network connection setting - Wired LAN -........7 1.2.1 Equipments connection ....................
Page 135 Contents 6. Network Bridge Function ............52 6.1 Connecting devices .................. 52 6.2 Communication setup ................53 6.3 Communication port ................. 53 6.4 Transmission method ................54 6.4.1 HALF-DUPLEX ......................54 6.4.2 FULL-DUPLEX ....................... 55 7. Other Functions ..............56 7.1 E-mail Alerts .....................
Page 136: Caution
Caution Caution To use the wireless network function of this projector, the designated USB wire- less adapter that is sold as an option is required. For precautions according to the standards and laws, refer to the documents that come with the adapter. [Restriction on plugging and unplugging the USB wireless adapter] Before you insert or pull out the USB wireless adapter from the projector, turn off the power of the projector and pull out the power cord’s plug from the outlet.
Page 137: Connection To The Network
1. Connection to the network 1. Connection to the network 1.1 System requirements 1.1.1 Required equipment preparation The following equipments are required to connect the projector to your computer through the network. ■ Common The projector: 1 unit, Computer : minimum 1 set ■...
Page 138 NORMAL. ( SETUP menu in the Operating Guide) • You can get the latest version of the applications for the network functions of the projector and the latest information for this product from the Hitachi website. (http://www.hitachi-america.us/digitalmedia or http://www.hitachidigitalmedia. com).
Page 139: Manual Network Connection Setting - Wired Lan
1. Connection to the network 1.2 Manual network connection setting - Wired LAN - This section explains how to set it up manually. 1.2.1 Equipments connection Connect the projector and a computer with a LAN cable. * Before connecting with an existing network, contact the network administrator. Next, check the following computer settings.
Page 140 1. Connection to the network 1.2 Manual network connection setting - Wired LAN - (continued) 5) Right-click "Local Area Connection" to open the menu, and select "Properties". 6) Select "Internet Protocol Version 4 (TCP/IPv4)" and click [Properties]. 7) Select "Use the following IP address" and conﬁgure the IP address, Subnet mask and Default gateway for the computer accordingly.
Page 141 1. Connection to the network 1.2 Manual network connection setting - Wired LAN - (continued) [About IP address] ■ Setting manually The Network address portion of the IP address setting on your computer must be the same as the setting on the projector. Also, the entire IP address on the computer must not overlap with that of the other devices on the same network, including the projector.
Page 142: Internet Option" Setting
1. Connection to the network 1.2 Manual network connection setting - Wired LAN - (continued) 1.2.3 “Internet Option” setting 1) Click “Internet Options” in “Network and Sharing Center” window to open “Internet Properties” window. 2) Click “Connections” tab and then click [LAN settings] button to open “Local Area Network (LAN) Settings”.
Page 143: Manual Network Connection Setting - Wireless Lan
1. Connection to the network 1.3 Manual network connection setting - Wireless LAN - Using the designated USB wireless adapter (option) on the projector enables the projector and computer to communicate in both the Ad-Hoc and Infrastructure modes. This section is intended to explain how to set up wireless LAN connection manually.
Page 144: Wireless Lan Connection Set Up
1. Connection to the network 1.3 Manual network connection setting - Wireless LAN - (continued) 1.3.2 Wireless LAN connection set up ® Using wireless LAN utility for Windows 7 standard. Wireless LAN initial settings for the projector is as follows. Connection Control : Ad-Hoc SSID...
Page 145 1. Connection to the network 1.3 Manual network connection setting - Wireless LAN - (continued) 4) Select "Use the following IP address" and conﬁgure the IP address, Subnet mask and Default gateway for the computer accordingly. After setting is complete, click [OK] to close the window. [About IP address] The Network address portion of the IP address setting on your computer must be the same as the setting on the projector.
Page 146 1. Connection to the network 1.3 Manual network connection setting - Wireless LAN - (continued) 5) Right-click "Wireless Network Connection" to open the menu, and select "Connect / Disconnect". 6) From the connectable wireless networks, select the SSID of the projector (set to "wireless"...
Page 147: Network Presentation
To use Network Presentation, an exclusive application, "LiveViewer" is required. It can be installed from the bundled application CD. You can also download the latest version and relevant information from the Hitachi website (http://www. hitachi-america.us/digitalmedia or http://www.hitachidigitalmedia.com). For details of Network Presentation and instructions to install the "LiveViewer", refer to the manual for "LiveViewer".
Page 148: Web Control
3. Web Control 3. Web Control You can adjust or control the projector via a network from a web browser on a computer that is connected to the same network. ® NOTE • Internet Explorer 6.0 or later is required. ®...
Page 149: Projector Web Control
3. Web Control 3.1 Projector Web Control 3.1.1 Logon To use the Projector Web Control function, you need to logon with your user name and password. Below are the factory default settings for user name and password. Logon window User name Password Administrator ...
Page 150: Network Information
3. Web Control 3.1 Projector Web Control (continued) 3.1.2 Network Information Displays the projector’s current network conﬁguration settings. Item Description Displays information common to both wireless and wired Common Information LAN. Projector Name Displays the projector name settings. Wireless Information Displays the current settings of wireless LAN.
Page 151: Network Settings
3. Web Control 3.1 Projector Web Control (continued) 3.1.3 Network Settings Displays and conﬁgures network settings. Item Description Common Setup Displays information common to both wireless and wired LAN. Conﬁgures the name of the projector. The length of the Projector Name can be up to 64 alphanumeric characters.
Page 152 3. Web Control 3.1 Projector Web Control - Network Settings (continued) Item Description Wireless Setup Conﬁgures the wireless LAN settings. Mode Select " AD-HOC" or " Infrastructure". IP Conﬁguration Conﬁgures network settings. DHCP ON Enables DHCP. DHCP OFF Disables DHCP. IP Address Conﬁgures the IP address when DHCP is disabled.
Page 153 3. Web Control 3.1 Projector Web Control - Network Settings (continued) Item Description Wired Setup Conﬁgures the wired LAN settings. IP Conﬁguration Conﬁgures network settings. DHCP ON Enables DHCP. DHCP OFF Disables DHCP. IP Address Conﬁgures the IP address when DHCP is disabled. Subnet Mask Conﬁgures the subnet mask when DHCP is disabled.
Page 154: Port Settings
3. Web Control 3.1 Projector Web Control (continued) 3.1.4 Port Settings Displays and conﬁgures communication port settings. Item Description Network Control Port1 Conﬁgures command control port 1 (Port:23). (Port:23) Port open Click the [Enable] check box to use port 23. Click the [Enable] check box when authentication is required Authentication for this port.
Page 155 3. Web Control 3.1 Projector Web Control - Port Settings (continued) Item Description SNMP Port Conﬁgures the SNMP port. Port open Click the [Enable] check box to use SNMP. Conﬁgures the destination of the SNMP Trap in IP format. • The address allows not only IP address but also domain Trap address name if the valid DNS server is setup in the Network Settings.
Page 156: Mail Settings
3. Web Control 3.1 Projector Web Control (continued) 3.1.5 Mail Settings Displays and conﬁgures e-mail addressing settings. Item Description Click the [Enable] check box to use the e-mail function. Send Mail Conﬁgure the conditions for sending e-mail under the Alert Settings.
Page 157: Alert Settings
3. Web Control 3.1 Projector Web Control (continued) 3.1.6 Alert Settings Displays and conﬁgures failure & alert settings. Item Description Cover Error The lamp cover has not been properly ﬁxed. Fan Error The cooling fan is not operating. The lamp does not light, and there is a possibility that interior Lamp Error portion has become heated.
Page 158 3. Web Control 3.1 Projector Web Control - Alert Settings (continued) The Alert Items are shown below. Item Description Conﬁgures the time to alert. Alarm Time (Only Lamp Time Alarm and Filter Time Alarm.) SNMP Trap Click the [Enable] check box to enable SNMP Trap alerts. Click the [Enable] check box to enable e-mail alerts.
Page 159: Schedule Settings
3. Web Control 3.1 Projector Web Control (continued) 3.1.7 Schedule Settings Displays and conﬁgures schedule settings. Item Description Daily Conﬁgures the daily schedule. Sunday Conﬁgures the Sunday schedule. Monday Conﬁgures the Monday schedule. Tuesday Conﬁgures the Tuesday schedule. Wednesday Conﬁgures the Wednesday schedule. Thursday Conﬁgures the Thursday schedule.
Page 160 3. Web Control 3.1 Projector Web Control - Schedule Settings (continued) The schedule settings are shown below. Item Description Schedule Click the [Enable] check box to enable the schedule. Conﬁgures the month and date. Date (Month/Day) This item appears only when Speciﬁc date (No. 1-5) is selected.
Page 161 3. Web Control 3.1 Projector Web Control - Schedule Settings (continued) NOTE • After the projector is moved, check the date and time set for the projector before conﬁguring the schedules. • The internal clock’s time may not remain accurate. Using SNTP is recommended to maintain accurate time.
Page 162: Date/Time Settings
3. Web Control 3.1 Projector Web Control (continued) 3.1.8 Date/Time Settings Displays and conﬁgures the date and time settings. Item Description Current Date Conﬁgures the current date in year/month/day format. Current Time Conﬁgures the current time in hour:minute:second format. Click the [ON] check box to enable daylight savings time and Daylight Savings Time set the following items.
Page 163 3. Web Control 3.1 Projector Web Control - Date/Time Settings (continued) Item Description Conﬁgures the time difference. Set the same time difference Time difference as the one set on your computer. If unsure, consult your IT manager. Click the [ON] check box to retrieve Date and Time SNTP information from the SNTP server and set the following items.
Page 164: Security Settings
3. Web Control 3.1 Projector Web Control (continued) 3.1.9 Security Settings Displays and conﬁgures passwords and other security settings. Item Description User Account Conﬁgures the user name and password. Conﬁgures the user name. User name The length of the text can be up to 32 alphanumeric characters.
Page 165: Projector Control
3. Web Control 3.1 Projector Web Control (continued) 3.1.10 Projector Control The items shown in the table below can be performed using the Projector Control menu. Select an item with the mouse. Most of the items have a submenu. Refer to the table below for details.
Page 166 3. Web Control 3.1 Projector Web Control - Projector Control (continued) Item Description PICTURE BRIGHTNESS Adjusts the brightness setting. CONTRAST Adjusts the contrast setting. GAMMA Selects the gamma setting. COLOR TEMP Selects the color temperature setting. COLOR Adjusts the color setting. TINT Adjusts the tint setting.
Page 167 3. Web Control 3.1 Projector Web Control - Projector Control (continued) Item Description SETUP AUTO KEYSTONE Performs the automatic keystone distortion setting. EXECUTE KEYSTONE V Adjusts the vertical keystone distortion setting. AUTO ECO MODE Turns on/off the automatic eco mode function. ECO MODE Selects the eco mode.
Page 168 3. Web Control 3.1 Projector Web Control - Projector Control (continued) Item Description AUDIO VOLUME Adjusts the volume setting. SPEAKER Turns the built-in speaker on/off. AUDIO SOURCE - Assigns the AUDIO SOURCE - COMPUTER IN1 input port. COMPUTER IN1 AUDIO SOURCE - Assigns the AUDIO SOURCE - COMPUTER IN2 input port.
Page 169 3. Web Control 3.1 Projector Web Control - Projector Control (continued) Item Description OPTION AUTO SEARCH Turns the automatic signal search function on/off. Turns the automatic keystone distortion correction function AUTO KEYSTONE on/off. DIRECT POWER ON Turns the direct power on function on/off. Conﬁgures the timer to shut off the projector when no signal AUTO POWER OFF is detected.
Page 170 3. Web Control 3.1 Projector Web Control - Projector Control (continued) The items shown in the table below can be performed using the Projector Control menu. Click the [Quit Presenter Mode]. Item Description SERVICE Quit Presenter Mode Quit compulsorily from the Presenter mode.
Page 171: Remote Control
3. Web Control 3.1 Projector Web Control (continued) 3.1.11 Remote Control You can use your Web browser to control the projector. The functions on the bundled remote control are assigned to the Web Remote Control screen. • Do not attempt to control the projector with the projector’s remote control and via your Web browser at the same time.
Page 172: Projector Status
3. Web Control 3.1 Projector Web Control (continued) 3.1.12 Projector Status Displays the settings and status of the projector. Item Description Error Status Displays the current error status Lamp Time Displays the usage time for the current lamp. Filter Time Displays the usage time for the current ﬁlter.
Page 173: Network Restart
3. Web Control 3.1 Projector Web Control (continued) 3.1.13 Network Restart Restarts the projector’s network connection. Item Description Restarts the projector’s network connection in order to Restart activate new conﬁguration settings. NOTE • Restarting requires you to re-log on in order to further control or conﬁgure the projector via a web browser.
Page 174: Crestron E-Control
3. Web Control ® 3.2 Crestron e-Control The Main window as shown above is displayed at ﬁrst. However, if you have enabled User Password on the Tools window 46), a dialog prompting you to enter the password as shown on the right will be displayed, and no operation is enabled until you have entered the password.
Page 175: Main Window
3. Web Control ® 3.2 Crestron e-Control (continued) 3.2.1 Main window You can operate the basic controls of the projector on this screen. NOTE • If the projector is in the standby mode, only the Power button can be operated. 1 Click a button and operate as follows.
Page 176 3. Web Control ® 3.2 Crestron e-Control - Main window (continued) 3 Click a button and operate as follows. To show the hidden buttons, click the ◄ / ► icons at the left and right ends. Button Description Freeze Turns Freeze on/off. Contrast Adjusts the contrast setting.
Page 177: Tools Window
3. Web Control ® 3.2 Crestron e-Control (continued) 3.2.2 Tools window ® Conﬁgures the settings between the projector and Crestron control system. Click the [Exit] button to return to the Main window. NOTE • If two-byte characters are used, the input text or numbers cannot be set correctly.
Page 178 3. Web Control ® 3.2 Crestron e-Control - Tools window (continued) 3 Projector (continued) Conﬁgures the network settings of the projector. Item Description DHCP Enables DHCP. IP Address Conﬁgures the IP address when DHCP is disabled. Subnet Mask Conﬁgures the subnet mask when DHCP is disabled. Default Gateway Conﬁgures the default gateway when DHCP is disabled.
Page 179: Info Window
3. Web Control ® 3.2 Crestron e-Control (continued) 3.2.3 Info window Displays the settings and status of the projector. Click the [Exit] button to return to the Main window. 1 Projector Information Item Description Projector Name Displays the projector name settings. Location Displays the location name of the projector.
Page 180: Help Desk Window
3. Web Control ® 3.2 Crestron e-Control (continued) 3.2.4 Help Desk window Sends/receives messages to/from the administrator for Crestron RoomView Express. Button Description Send Sends a message. Check the received message.
Page 181: Emergency Alert
3. Web Control ® 3.2 Crestron e-Control (continued) 3.2.5 Emergency Alert ® When the administrator for Crestron RoomView Express sends out an alert message, it will be displayed on the screen. You can reply to the alert message via a chat format. Input a message in the box below the alert message, and click the [Send] button.
Page 182: My Image Function
MY IMAGE transmission requires an exclusive application for your computer. Use the application to transfer the image data. It can be downloaded from the Hitachi web site (http://www.hitachi-america.us/ digitalmedia or http://www.hitachidigitalmedia.com). For information on the necessary settings and operations for the computer and projector, refer to the manual for the application.
Page 183: Messenger Function
Messenger function requires an exclusive application for your computer. To edit, transfer and display the text data, use the application. You can download it from the Hitachi web site (http://www.hitachi-america.us/digitalmedia or http:// www.hitachidigitalmedia.com). For information on the necessary settings and operations for the computer and projector, refer to the manual for the application.
Page 184: Network Bridge Function
6. Network Bridge Function 6. Network Bridge Function This projector is equipped with the NETWORK BRIDGE function to perform mutual conversion of a network protocol and a serial interface. By making use of the NETWORK BRIDGE function, a computer that is connected to the projector via wireless or wired LAN is able to control an external device via RS-232C communication using the projector as a network terminal.
Page 185: Communication Setup
6. Network Bridge Function 6.2 Communication setup To conﬁgure the setup of the communication using NETWORK BRIDGE for the projector, use items in the COMMUNICATION menu. Open the menu of the projector and select the OPTION - SERVICE - COMMUNICATION menu. OPTION menu >...
Page 186: Transmission Method
6. Network Bridge Function 6.4 Transmission method The transmission method can be selected from the menus, only when the NETWORK BRIDGE is selected for the COMMUNICATION TYPE. OPTION menu > SERVICE > COMMUNICATION in the Operating Guide) HALF-DUPLEX FULL-DUPLEX 6.4.1 HALF-DUPLEX This method lets the projector make two way communication, but only one direction, either transmitting or receiving data, is allowed at a time.
Page 187: Full-Duplex
6. Network Bridge Function 6.4 Transmission method (continued) NOTE • With using the HALF-DUPLEX method, the projector can send out 254 byte data as maximum at once. • If it is not required to monitor the response data from an external device and the RESPONSE LIMIT TIME is set to OFF, the projector can receive the data from the computer and send it out to an external device continuously.
Page 188: Other Functions
7. Other Functions 7. Other Functions 7.1 E-mail Alerts The projector can automatically send an alert message to the speciﬁed e-mail addresses when the projector detects a certain condition that is requiring maintenance or detected an error. NOTE • Up to ﬁve e-mail addresses can be speciﬁed. •...
Page 189 7. Other Functions 7.1 E-mail Alerts (continued) 5) Click the [Alert Settings] on the main menu to conﬁgure the E-mail Alerts settings. 6) Select and conﬁgure each alert item. Refer to item 3.1.6 Alert Settings ( for further information. 7) Click the [Apply] button to save the settings. Failure/Warning e-mails are formatted as follows: Subject line : ...
Page 190: Projector Management Using Snmp
7. Other Functions 7.2 Projector Management using SNMP The SNMP (Simple Network Management Protocol) enables to manage the projector information, which is a failure or warning status, from the computer on the network. The SNMP management software will be required on the computer to use this function.
Page 191: Event Scheduling
7. Other Functions 7.3 Event Scheduling The scheduling function enables to setup scheduled events including power on / power off. It enables to be “self-management” projector. NOTE • You can schedule the following control events: Power, Input Source, My Image, Messenger, Slideshow. ( •...
Page 192 7. Other Functions 7.3 Event Scheduling(continued) Schedule Settings ( Schedule settings can be conﬁgured from a web browser. Example: If the IP address of the projector is set to 192.168.1.10: 1) Enter “http://192.168.1.10/” into the address bar of the web browser, and select Projector Web Control from the selection window.
Page 193 7. Other Functions 7.3 Event Scheduling(continued) Date/Time Settings ( The Date/Time setting can be adjusted via a web browser. Example: If the IP address of the projector is set to 192.168.1.10: 1) Enter “http://192.168.1.10/” into the address bar of the web browser, and select Projector Web Control from the selection window.
Page 194: Command Control Via The Network
7. Other Functions 7.4 Command Control via the Network You can conﬁgure and control the projector via the network using RS-232C commands. Communication Port The following two ports are assigned for the command control. TCP #23 (Network Control Port1 (Port: 23)) TCP #9715 (Network Control Port2 (Port: 9715)) NOTE •...
Page 195 7. Other Functions 7.4 Command Control via the Network (continued) When the authentication setting is enabled, the following settings are required. 7) Click the [Security Settings] on the main menu. 8) Click the [Network Control] and enter the desired authentication password. * See NOTE.
Page 196 7. Other Functions 7.4 Command Control via the Network (continued) Command Format Command formats differ among the different communication ports. ● TCP #23 You can use the RS-232C commands without any changes. The reply data format is the same as the RS-232C commands. ( RS-232C Communication in the Operating Guide - Technical) However, the following reply will be sent back in the event of authentication...
Page 197 7. Other Functions 7.4 Command Control via the Network (continued) Reply Data format The connection ID (the data is same as the connection ID data on the sending data format) is attached to the RS-232C commands reply data. Connection Reply 0x06...
Page 198 7. Other Functions 7.4 Command Control via the Network (continued) Automatic Connection Break The TCP connection will be automatically disconnected after there is no communication for 30 seconds after being established. Authentication The projector does not accept commands without authentication success when authentication is enabled.
Page 199: Crestron Roomview
7. Other Functions ® 7.5 Crestron RoomView ® Crestron RoomView is a multi-user resource management program provided by Crestron Electronics, Inc. It is an application for managing and controlling the projector and other AV devices collectively. ® ® For details of Crestron RoomView , refer to the Crestron website.
Page 200: Troubleshooting
8. Troubleshooting 8. Troubleshooting Reference Problem Likely Cause Things to Check Page Number • Bring the computer and projector closer together. Weak radio signal • Radio waves won’t go – through concrete and metal (steel doors, etc.) If there is a wireless conﬁguration utility loaded Cannot communicate due on your computer, check its...
Page 201: Speciﬁcations
9. Speciﬁcations 9. Speciﬁcations Item Specifications Control software Dedicated computer application and Web browser Corresponding TCP/IP, DHCP client and HTTP server protocol Wireless LAN (IEEE802.11b/g/n) Network (Ad-Hoc and Infrastructure modes) Wired LAN(100Base-TX/10Base-T) WEP (64/128bit), WPA-PSK (TKIP/AES), Security WPA2-PSK (TKIP/AES), SSID ®...
Page 202: Warranty And After-Sales Service
10. Warranty and after-sales service 10. Warranty and after-sales service If a problem occurs with the equipment, please read 8. Troubleshooting ( section ﬁrst and review all suggested check points. After that, please contact your dealer or service company, if you still have the problem. They will tell you what warranty condition is applied.
Page 203 Projector CP-X2015WN/CP-X2515WN/CP-X3015WN/ CP-X4015WN/CP-WX2515WN/CP-WX3015WN User's Manual (detailed) Operating Guide – Technical Example of PC signal Resolution (H x V) H. frequency (kHz) V. frequency (Hz) Rating Signal mode 720 x 400 37.9 85.0 VESA TEXT 640 x 480 31.5 59.9 VESA VGA (60Hz) 640 x 480 37.9...
Page 204 Initial set signals Initial set signals The following signals are used for the initial settings. The signal timing of some PC models may be different. In such case, adjust the items V POSITION and H POSITION in the IMAGE menu. Back porch (B) Front porch (D) Back porch (b)
Page 205 Connection to the ports Connection to the ports NOTICE ►Use the cables with straight plugs, not L-shaped ones, as the input ports of the projector are recessed. AUDIO IN AUDIO OUT COMPUTER IN1, COMPUTER IN2, MONITOR OUT D-sub 15pin mini shrink jack ...
Page 206 Connection to the ports (continued) AUDIO IN AUDIO OUT S-VIDEO Mini DIN 4pin jack • System: NTSC, PAL, SECAM, PAL-M, PAL-N, NTSC4.43, PAL (60Hz) Signal Color signal 0.286Vp-p (NTSC, burst), 75Ω terminator Color signal 0.300Vp-p (PAL/SECAM, burst) 75Ω terminator Brightness signal, 1.0Vp-p, 75Ω terminator Ground Ground VIDEO...
Page 207 Connection to the ports (continued) AUDIO IN AUDIO OUT AUDIO IN1, AUDIO IN2 Ø3.5 stereo mini jack • 200 mVrms 47kΩ terminator AUDIO IN3 AUDIO OUT RCA jack x2 RCA jack x2 • 200 mVrms 47kΩ terminator • 200 mVrms 1kΩ output impedance Ø3.5 mono mini jack ...
Page 208 Connection to the ports (continued) AUDIO IN AUDIO OUT CONTROL D-sub 9pin plug 9 8 7 • About the details of RS-232C communication, 5 4 3 2 1 please refer to the next chapter. Signal Signal Signal (No connection) (No connection) Ground (No connection) (No connection)
Page 209 Connection to the ports (continued) To input component video signal to COMPUTER IN ports D-sub plug RCA plugs RCA connectors AUDIO IN AUDIO OUT COMPONENT VIDEO OUT VCR/DVD/Blu-ray Disc player To input component video signal to the COMPUTER IN1 or COMPUTER IN2 port of the projector, use a RCA to D-sub cable or adapter.
Page 210 RS-232C Communication RS-232C Communication When the projector connects to the computer by RS-232C communication, the projector can be controlled with RS-232C commands from the computer. For details of RS-232C commands, refer to RS-232C Communication / Network 17). command table ( Connection Turn off the projector and the computer.
Page 211: Communication Settings
RS-232C Communication (continued) Communication settings 1. Protocol 19200bps,8N1 2. Command format ("h" shows hexadecimal) Byte Number Command Header Data Header Data Setting Action Type code size ﬂag code Packet Action Change setting to desired value [(bL)(bH)] (aL) (aH) 01h 00h (bL) (bH) (cL) (cH) by [(cL)(cH)].
Page 212 RS-232C Communication (continued) 3. Response code / Error code ("h" shows hexadecimal) (1) ACK reply : 06h When the projector receives the Set, Increment, Decrement or Execute command correctly, the projector changes the setting data for the speciﬁed item by [Type], and it returns the code. (2) NAK reply : 15h When the projector cannot understand the received command, the projector returns the error code.
Page 213 Command Control via the Network Command Control via the Network When the projector connects network, the projector can be controlled with RS- 232C commands from the computer with web browser. For details of RS-232C commands, refer to RS-232C Communication / Network 17).
Page 214 Command Control via the Network (continued) Communication Port The following two ports are assigned for the command control. TCP #23 TCP #9715 Conﬁgure the following items form a web browser when command control is used. Port Settings Click the [Enable] check box to open [Network Port open Control Port1 (Port: 23)] to use TCP #23.
Page 215: Command Control Settings
Command Control via the Network (continued) Command control settings [TCP #23] 1. Command format Same as RS-232C communication, refer to RS-232C Communicaton command format. 2. Response code / Error code ("h" shows hexadecimal) Four of the response / error code used for TCP#23 are the same as RS-232C Communication (1)~(4).
Page 216 Command Control via the Network (continued) 2. Response code / Error code ("h" shows hexadecimal) The connection ID is attached for the TCP#23's response / error codes are used. The connection ID is same as the sending command format. (××h : connection ID) (1) ACK reply : 06h + ××h (2) NAK reoly : 15h + ××h (3) Error reply : 1Ch + 0000h + ××h...
Page 217 Network Bridge Communication Network Bridge Communication This projector is equipped with NETWORK BRIDGE function. When the projector connects to the computer by wired or wireles LAN communicaton, an external device that is connected with this projector by RS- 232C communication can be controlled from the computer as a network terminal. For details, see the 6.
Page 218 Network Bridge Communication (continued) Communication settings For communication setting, use the OPTION - SERVICE - COMMUNICATION menu. ( OPTION menu - SERVICE - COMMUNICATION in the Operating Guide) Item Condition BAUD RATE 4800bps / 9600bps / 19200bps / 38400bps Data length 8 bit (ﬁxed) PARITY NONE/ODD/EVEN...
Page 219 RS-232C Communication / Network command table RS-232C Communication / Network command table Command Data Names Operation Type Header Action Type Setting Code Turn off BE EF 06 00 2A D3 01 00 00 60 00 00 Turn on BE EF 06 00 BA D2 01 00...
Page 220 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting Code BE EF 06 00 89 D2 02 00 03 20 00 00 BRIGHTNESS Increment BE EF 06 00 EF D2 04 00 03 20 00 00 Decrement BE EF...
Page 221 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting Code BE EF 06 00 C4 FE 02 00 95 30 00 00 User Gamma Point 6 Increment BE EF 06 00 A2 FE 04 00 95 30 00 00...
Page 222 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting Code BE EF 06 00 40 F5 02 00 B6 30 00 00 COLOR TEMP Increment BE EF 06 00 26 F5 04 00 B6 30 00 00 OFFSET G...
Page 223 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting Code BE EF 06 00 F1 82 02 00 01 21 00 00 H POSITION Increment BE EF 06 00 97 82 04 00 01 21 00 00 Decrement...
Page 224 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting Code BE EF 06 00 86 D8 01 00 22 20 00 00 AUTO NORMAL BE EF 06 00 16 D9 01 00 22 20 01 00 HDMI RANGE ENHANCED...
Page 225 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting Code COMPUTER IN1 BE EF 06 00 86 F5 01 00 B2 20 00 00 COMPUTER IN2 BE EF 06 00 46 F7 01 00 B2 20 04 00 MONITOR OUT -...
Page 226 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting Code BE EF 06 00 45 CC 02 00 66 20 00 00 VOLUME - USB TYPE Increment BE EF 06 00 23 CC 04 00 66 20 00 00...
Page 227 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting Code BE EF 06 00 DA DF 01 00 3B 20 00 00 AUDIO IN1 BE EF 06 00 4A DE 01 00 3B 20 01 00 AUDIO IN2 BE EF...
Page 228 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting Code ENGLISH BE EF 06 00 F7 D3 01 00 05 30 00 00 FRANÇAIS BE EF 06 00 67 D2 01 00 05 30 01 00 DEUTSCH BE EF...
Page 229 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting Code MyScreen BE EF 06 00 FB CA 01 00 00 30 20 00 ORIGINAL BE EF 06 00 FB E2 01 00 00 30 40 00 BLUE BE EF...
Page 230 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting Code BE EF 06 00 B6 D6 01 00 16 20 00 00 AUTO SEARCH BE EF 06 00 26 D7 01 00 16 20 01 00 BE EF 06 00...
Page 231 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting Code COMPUTER IN1 BE EF 06 00 C6 32 01 00 01 36 00 00 COMPUTER IN2 BE EF 06 00 06 30 01 00 01 36 04 00 HDMI...
Page 232 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting Code COMPUTER IN1 BE EF 06 00 FA 38 01 00 20 36 00 00 COMPUTER IN2 BE EF 06 00 3A 3A 01 00 20 36 04 00 HDMI...
Page 233 PJLink command PJLink command Commands Control Description Parameter or Response 0 = Standby POWR Power Contorol 1 = Power On 0 = Standby POWR ? Power Status inquiry 1 = Power On 2 = Cool Down 11 = COMPUTER IN 1 12 = COMPUTER IN 2 22 = S-VIDEO 23 = VIDEO...
Page 234 11 12 22 23 31 41 51 52 Responds with the name set in "PROJECTOR NAME ? Projector Name inquiry NAME" of "NETWORK" Manufucturer's Name INF1 ? HITACHI inquiry Your model name, "CP-X2015WN", "CP- INF2 ? Model Name inquiry X2515WN", "CP-X3015WN", "CP-X4015WN", "CP-WX2515WN"...
Page 235 Projector CP-X2015WN/CP-X2515WN/CP-X3015WN/ CP-X4015WN/CP-WX2515WN/CP-WX3015WN User's Manual (concise) Thank you for purchasing this projector. Please read through this manual before using this product, in order to use safely and utilize well the product. WARNING ►Before using this product, be sure to read all manuals for this product.
Page 236: First Of All
First of all Entries and graphical symbols explanation The following entries and graphical symbols are used for the manuals and the product as follows, for safety purpose. Please know their meanings beforehand, and heed them. WARNING This entry warns of a risk of serious personal injury or even death. CAUTION This entry warns of a risk of personal injury or physical damage.
Page 237: Regulatory Notices
CP-X4015WN, CP-WX2515WN, CP-WX3015WN Responsible Party Hitachi America, Ltd. Address 900 Hitachi way, Chula Vista, CA 91914-3556 U.S.A. Telephone Number +1 -800-448-2244 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.This equipment has...
Page 238: About Waste Electrical And Electronic Equipment
Regulatory notices (continued) About Waste Electrical and Electronic Equipment The mark is in compliance with the Waste Electrical and Electronic Equipment Directive 2002/96/EC (WEEE). The mark indicates the requirement NOT to dispose the equipment including any spent or discarded batteries or accumulators as unsorted municipal waste, but use the return and collection systems available.
Page 239: Preparing For The Remote Control
Holding the hook part of the battery cover, remove it. Align and insert the two AA batteries HITACHI MAXELL or HITACHI MAXELL ) according ENERGY, Part No.LR6 or R6P to their plus and minus terminals as indicated in the remote control.
Page 240: Arrangement
Arrangement Refer to table T-1,T-2 and T-3 and ﬁgures F-1 and F-2 at the end of this manual to determine the screen size and projection distance (from the projector’s end). The values shown in the table are calculated for a full size screen. Screen size (diagonal) Projection distance (±10%, from the projector's end) Screen height (±10%)
Page 241: Connecting With Your Devices
Connecting with your devices Before connecting the projector to a device, consult the manual of the device to conﬁrm that the device is suitable for connecting with this projector and prepare the required accessories, such as a cable in accord with the signal of the device. Consult your dealer when the required accessory did not come with the product or the accessory is damaged.
Page 242: Fastening The Adapter Cover
Fastening the adapter cover Use the supplied adapter cover to prevent the USB wireless adapter (optional) from coming off easily and prevention from burn injury. Loosen the screw (marked with triangle) on the bottom left of the USB TYPE A port. Insert the tab of the cover into the hole at the upper right of the USB TYPE A port in the direction of the arrow.
Page 243: Turning On The Power
Turning on the power Make sure that the power cord is ﬁrmly and correctly connected to the projector and the outlet. STANDBY/ON button Make sure that the POWER indicator is POWER indicator steady orange. Then remove the lens cover. Press the STANDBY/ON button on the projector or the remote control.
Page 244: Adjusting The Projector's Elevator
Adjusting the projector’s elevator When the place to put the projector is slightly uneven to the left or right, use the elevator feet to place the projector horizontally. Using the feet can also tilt the projector 14° in order to project at a suitable angle to the screen, elevating the front side of the projector within 14 degrees.
Page 245: Displaying The Picture
Displaying the picture Activate your signal source. Turn the VIDEO COMPUTER MY SOURCE/ DOC.CAMERA signal source on, and make it send the ASPECT AUTO SEARCH BLANK MAGNIFY FREEZE PAGE VOLUME VOLUME+ button signal to the projector. DOWN VOLUME- button Press the INPUT button on the projector. MY BUTTON KEYSTONE MUTE...
Page 246: Turning Off The Power
Turning off the power Press the STANDBY/ON button on the STANDBY/ON button projector or the remote control. POWER indicator The message “Power off?” will appear on the screen for about 5 seconds. Press the STANDBY/ON button again while the message appears. The projector lamp will go off, and the POWER indicator will begin blinking in orange.
Page 247: Replacing The Lamp
Replacing the lamp A lamp has ﬁnite product life. Using the lamp for long periods of time could cause the pictures darker or the color tone poor. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. Preparation of a new lamp and early replacement are recommended.
Page 248 Replacing the lamp (continued) HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE WARNING ►The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them.
Page 249: Cleaning And Replacing The Air Filter
Cleaning and replacing the air ﬁlter Please check and clean the air ﬁlter periodically. When the indicators or a message prompts you to clean the air ﬁlter, comply with it as soon as possible. The air ﬁlter has two kinds of ﬁlters inside. Replace the ﬁlters when they are damaged or too soiled. To prepare the new ﬁlters, make contact with your dealer and tell the following type number.
Page 250: Using The Cd Manual
Using the CD manual The other manuals for this product are written into the included CD-ROM titled “User’s Manual (detailed)”. Before using the CD-ROM, please read the following to ensure the proper use. System requirements The system for using the CD-ROM requires the following. ®...
Page 251: Speciﬁcations
Speciﬁcations Item Speciﬁcation Product name Liquid crystal projector CP-X2015WN, CP-X2515WN, CP-X3015WN, CP-X4015WN: Liquid Crystal 786,432 pixels (1024 horizontal x 768 vertical) Panel CP-WX2515WN, CP-WX3015WN: 1,024,000 pixels (1280 horizontal x 800 vertical) Lamp W UHP Speaker 16 W mono (8 W x 2) Power supply/ AC 100-120 V: 3.3 A, AC 220-240 V: 1.7 A Rated current...
Page 252: Troubleshooting - Warranty And After-Service
If this does not resolve the problem, please consult your dealer or service company. They will tell you what warranty condition is applied. Please check the following web address where you may ﬁnd the latest information for this projector. Product http://www.hitachi-america.us/digitalmedia information and Manuals : Production http://www.hitachidigitalmedia.com information : http://www.hitachiserviceeu.com/support/guides/...
Page 253 CP-X2015WN,X2515WN,3015WN (1024 x 768) (±10%) 4 : 3 screen 16 : 9 screen Screen size Projection distance Projection distance Screen Screen Screen (diagonal) Screen height height height height min. max. min. max. type inch inch inch inch inch inch inch inch (inch) 125 118...
Page 254 CP-WX2515WN,CP-WX3015WN (1280 x 800) (±10%) 16 : 10 screen 4 : 3 screen Screen size (diagonal) Projection distance Projection distance Screen Screen Screen Screen height height height height min. max. min. max. type inch inch inch inch inch inch inch inch (inch) 119 105...
Page 255 Computer AUDIO IN AUDIO OUT Computer External device Access point wireless adapter (optional) AUDIO IN storage AUDIO OUT device...
Page 256 VCR/DVD/Blu-ray Disc player AUDIO IN AUDIO OUT Speakers Microphone Monitor (with an ampliﬁ er) AUDIO IN AUDIO OUT...
Page 257 AUDIO AUDIO 317mm [unit: mm]...
Page 258 NOTE • The information in this manual is subject to change without notice. • The manufacturer assumes no responsibility for any errors that may appear in this manual. • The reproduction, transfer or copy of all or any part of this document is not permitted without express written consent. REMARQUE •...
Page 259 MALAYSIA Tel: 0211-5283-801 Tel: +60 -3-8911-2670 Email: [email protected] ► http://www.hitachiconsumer.com.my Hitachi Europe S.A. Hitachi Home Electronics Asia (S) Pte. Ltd. 364, Kifissias Ave. & 1, Delfon Str. 438A Alexandra Road #01-01/02/03 152 33 Chalandri Alexandra Technopark, 119967 SINGAPORE Athens GREECE...

This manual is also suitable for:

Cp-x2015wn Cp-wx3015wn Cp-x2515wn Cp-x3015wn Cp-x4015wn

Hitachi CP-WX2515WN User Manual

Table of Contents

Introduction

Setting up

Remote Control

Power On/Off

Operating

Easy Menu

PICTURE Menu

IMAGE Menu

INPUT Menu

SETUP Menu

AUDIO Menu

SCREEN Menu

OPTION Menu

NETWORK Menu

SECURITY Menu

Presentation Tools

Maintenance

Troubleshooting

Speciﬁcations

Table of Contents

Caution

1 Connection to the Network

2 Network Presentation

3 Web Control

4 My Image Function

5 Messenger Function

6 Network Bridge Function

7 Other Functions

8 Troubleshooting

9 Speciﬁcations

10 Warranty and After-Sales Service

Cp-X2015Wn/Cp-X2515Wn/Cp-X3015Wn/ Cp-X4015Wn/Cp-Wx2515Wn/Cp-Wx3015Wn

Quick Links

Chapters

Troubleshooting

Related Manuals for Hitachi CP-WX2515WN

Summary of Contents for Hitachi CP-WX2515WN

This manual is also suitable for:

Table of Contents