Summary of Contents for HP 316095-B21 - StorageWorks Edge Switch 2/24
Page 1
installation instructions hp StorageWorks edge switch 2/24 rack mount kit Product Version: FW V05.01.00-24/HAFM SW V07.01.00-09 Third Edition (June 2003) Part Number: AA-RTDGC-TE/958-000285-002 These installation instructions provide the procedures used for installing an HP StorageWorks Edge Switch 2/24 in an appropriate rack.
about this guide About this Guide These installation instructions provide information to help you rack mount the HP StorageWorks Edge Switch 2/24 in a standard HP rack. About this Guide “About this Guide” topics include: Overview, page 6 Conventions, page 7 Rack Stability, page 10 Getting...
Intended Audience This book is intended for use by administrators or technicians who are experienced with the following: StorageWorks FibreChannel technology from Hewlett-Packard. Rack-mounting hardware in standard HP racks. Related Documentation For a list of corresponding documentation included with this product, see the Related Documents section of the HP StorageWorks Edge Switch Release Notes.
About this Guide Conventions Conventions consist of the following: Document Conventions Text Symbols Equipment Symbols Document Conventions The document conventions included in Table 1 apply in most cases. Table 1: Document Conventions Element Convention Cross-reference links Blue text: Figure 1 Key and field names, menu items, Bold buttons, and dialog box titles...
About this Guide Caution: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or data. Note: Text set off in this manner presents commentary, sidelights, or interesting points of information. Equipment Symbols The following equipment symbols may be found on hardware for which this guide pertains.
Page 9
About this Guide Power supplies or systems marked with these symbols indicate the presence of multiple sources of power. WARNING: To reduce the risk of personal injury from electrical shock, remove all power cords to completely disconnect power from the power supplies and systems. Any product or assembly marked with these symbols indicates that the component exceeds the recommended weight for one individual to handle safely.
About this Guide Rack Stability Rack stability protects personnel and equipment. To reduce the risk of personal injury or damage to the WARNING: equipment, be sure that: The leveling jacks are extended to the floor. The full weight of the rack rests on the leveling jacks. In single rack installations, the stabilizing feet are attached to the rack.
About this Guide Getting Help If you still have a question after reading this guide, contact an HP authorized service provider or access our website: http://www.hp.com. HP Technical Support Telephone numbers for worldwide technical support are listed on the following HP website: http://www.hp.com/support/.
Page 12
About this Guide Edge Switch 2/24 Rack Mount Kit Installation Instructions...
Rack Mount Checklist This chapter describes the contents of the rack mount kit as well as tools or equipment required to complete the installation. Note: The hardware kit includes parts not required for the configuration described in these instructions. Edge Switch 2/24 Rack Mount Kit Installation Instructions...
Rack Mount Checklist Mounting Hardware Two (2) two-hole bar nuts Six (6) three-hole bar nuts (only 4 used) Eight (8) square alignment washers (required only for HP 9000, 10000 and 11000 series racks) Eight (8) Phillips panhead screws (10-32 x 1/2) with split lock and flat washers Four (4) Phillips flathead screws (8-32 x 7/16) Ten (10) Phillips panhead screws (10-32 x 5/8) with flat washer (only 2 used)
Rack Mount Checklist Brackets and Rails Brackets and rails included in the kit are shown in Figure 1: 1 Two (2 ) fixed-length slide rails (one left and one right) 2 Two (2) Front brackets 3 Two (2) Rear brackets (long) 4 Two (2) Rear spacing bracket 5 Rear bracket (short) - not used in this configuration Figure 1: Brackets included in kit...
Rack Mount Checklist Required Tools The following tools are required, but are not included in the kit: Torque driver with a T10 Torx bit #2 Phillips screwdriver Edge Switch 2/24 Rack Mount Kit Installation Instructions...
Rack Mount Instructions Read these instructions to rack mount the HP StorageWorks Edge Switch 2/24 in the appropriate HP, or comparable, 19-inch Electronic Industries Association (EIA) rack: HP 9000 series, 10000 series and 11000 series racks HP rack system/e or 19-inch EIA rack Edge Switch 2/24 Rack Mount Kit Installation Instructions...
Rack Mount Instructions Mounting the Adjustable Brackets in the Rack Use these steps to install the adjustable brackets on the rack. You will need a #2 Phillips screwdriver and eight 10x32 panhead screws to complete this procedure. Note: If you are installing the Edge Switch 2/24 in an HP 9000, 10000 or 11000 series rack, you will need eight square alignment washers to complete this procedure.
Rack Mount Instructions Mounting the Slide Rails on the Sides of the Switch Use these steps to install the slide rails on the sides of the switch as shown in Figure 2. You will need a torque driver with a T10 Torx bit (not supplied in the kit) and left and right slide rails to complete this procedure.
Rack Mount Instructions Installing the Switch in the Cabinet Use these steps to install the switch in the cabinet. You will need a #2 Phillips screwdriver and two rear spacing brackets to complete this procedure. 1. From the front side of the cabinet, slide the switch into the mounting brackets and along the rails until the rear of the switch is flush with the rear of the cabinet.
Page 22
Rack Mount Instructions Edge Switch 2/24 Rack Mount Kit Installation Instructions...