Quick Links
INSTALLATION AND SETUP GUIDE
GENERAL INFORMATION
The 5820L is a single-zone Slim-Line Door/Window
contact
transmitter
that
notification of intrusion. The 5820L can be used
only with alarm systems that support 5800 Series
wireless devices. The 5820L has its own unique
serial
number
permanently
manufacture. You must enroll the transmitter's
serial number in the control panel before it will
operate in the system. Refer to the control panel's
installation instructions for programming details.
Note: During programming of the control panel,
5820L transmitters must be enrolled as Input Type
3 (Supervised RF), Loop 1.
The transmitter is powered by one AAA Lithium (or
alkaline) battery that is easily replaced when a low
battery condition is indicated by the control panel.
TAMPER PROTECTION
Front and back-case tamper is provided using the
same switch. The front-case tamper is always
enabled. Adding the third screw as shown in Figure
2 enables the back-case tamper.
MAGNET ALIGNMENT
LOCATORS
MAGNET
GAP
0.5" MAX
Figure 1. 5820L (Typical Installation Arrangement)
MOUNTING
HOLE
TAMPER
PROTECTION
MOUNTING
HOLE
Figure 2. 5820L Mounting/Battery Location
Door/Window Contact Transmitter
Door/Window Contact Transmitter
Door/Window Contact Transmitter
Door/Window Contact Transmitter
MOUNTING
The description that follows assumes that the
provides
wireless
transmitter will be mounted as shown in Figure 1,
with the magnet located adjacent to the unit's left
side. The transmitter may, however, be installed in
any direction, as long as the relationship of the unit
assigned
during
to the magnet is maintained as shown in Figure 1.
1.
Note: Before mounting the transmitter and magnet
permanently using the double-back tape or
mounting screws, conduct a Go/No Go test (see
control's instructions) to verify adequate signal
strength and reorient or relocate the transmitter if
necessary.
2.
3.
4.
5.
6.
OPENING
7.
SLOT
Note: Do NOT attempt to remove the PCB from the
plastic cover for any reason.
BATTERY
(1.5VDC, AAA
BATTERY
LITHIUM OR
ALKALINE)
INSTALLATION/REPLACEMENT
+
Replace battery only with same or equivalent type.
TAMPER
SWITCH
Dispose of used batteries according to the battery
manufacturer's instruction.
1.
2.
Note:
the Specifications paragraph.
K9232V1 10/05 Rev. A
ADEMCO 5820L
Temporarily mount the 5820L and magnet
using the double-back tape supplied.
If the Go/No Go test was successful, remove
the transmitter's cover by inserting the flat
blade of a small screwdriver into the opening
slot at one end of the unit as shown in Figure 1,
and separating the two halves.
The 5820L must only be mounted against a flat
surface. A curved surface would cause undo
stress to the unit and possible failure to operate
properly.
Install mounting screws in the two outside
mounting holes as shown in Figure 2 using a #1
Phillips.
If the case-back tamper switch will be used,
install a third screw in the middle hole.
Mount the magnet (supplied) adjacent to the
two vertical positioning lines on the case side
(see Figure 1). The gap can be one-half an inch
maximum.
To reinstall the cover, position the cover so
that it covers the mounted case-back, and snap-
shut. The two case halves can only be fitted
together in one direction.
Remove the transmitter's cover (if it is not
off already) as described in Mounting; step 2.
Observe correct polarity and insert the
battery provided into the battery retainer clips
as shown in Figure 2.
Replace battery only with type specified in
Related Manuals for Honeywell 5820L - Slim Line Wireless Door/Window Transmitter
Summary of Contents for Honeywell 5820L - Slim Line Wireless Door/Window Transmitter
- Page 1 K9232V1 10/05 Rev. A ADEMCO 5820L Door/Window Contact Transmitter Door/Window Contact Transmitter Door/Window Contact Transmitter Door/Window Contact Transmitter INSTALLATION AND SETUP GUIDE GENERAL INFORMATION MOUNTING The 5820L is a single-zone Slim-Line Door/Window The description that follows assumes that the contact transmitter that provides...
- Page 2 FOR WARRANTY INFORMATION AND LIMITATIONS OF THE ENTIRE ALARM SYSTEM, REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED 165 Eileen Way, Syosset, New York 11791 Copyright © 2005 Honeywell International Inc. www.honeywell.com/security ÊK9232V1DŠ K9232V1 10/05 Rev. A...