HP CQ5110F - Presario - 3 GB RAM Upgrade And Service Manual
  1. Manuals
  2. Brands
  3. HP Manuals
  4. Desktop
  5. CQ5110F - Presario - 3 GB RAM
  6. Upgrade and service manual
HP CQ5110F - Presario - 3 GB RAM Upgrade And Service Manual

HP CQ5110F - Presario - 3 GB RAM Upgrade And Service Manual

Upgrading and servicing guide
Hide thumbs Also See for CQ5110F - Presario - 3 GB RAM:
Table of Contents

Quick Links

Upgrading and Servicing Guide
Table of Contents
loading

Related Manuals for HP CQ5110F - Presario - 3 GB RAM

Summary of Contents for HP CQ5110F - Presario - 3 GB RAM

  • Page 1 Upgrading and Servicing Guide...
  • Page 2 The only warranties for Hewlett-Packard products and services are set forth in the express statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.

  • Page 3: Table Of Contents

    Table of Contents Upgrading and Servicing Guide ...............1 Safety Information ....................1 Opening and Closing the Computer .................1 Preparing the computer ..................2 Before opening the computer ................2 After closing the computer ..................3 Removing the side panel..................3 Replacing the side panel ..................4 Removing the front panel ..................5 Replacing the front panel..................6 Locating Components Inside the Computer..............7...
  • Page 4 Table of Contents...

  • Page 5: Upgrading And Servicing Guide

    Upgrading and Servicing Guide Safety Information This product has not been evaluated for connection to an “IT” power system (an AC distribution system with no direct connection to the earth, according to IEC 60950). WARNING: Before you install and connect your system to the electrical power system, please read “Safety Information”...

  • Page 6: Preparing The Computer

    Preparing the computer Before you upgrade any component in your computer, you must prepare it so that you can safely handle it and the components. Read the following items before attempting to upgrade or service the computer: These procedures assume familiarity with the general terminology associated with personal computers, and with the safety practices and regulatory compliance required for using and modifying electronic equipment.

  • Page 7: After Closing The Computer

    After closing the computer To avoid injury and equipment damage, always complete the following steps, in this order, after closing the computer: Reconnect the power cord to the computer and to the electrical outlet. WARNING: To reduce the risk of electrical shock, fire, or damage to the equipment, do not plug telecommunications or telephone connectors into the network interface card (NIC) (labeled as an Ethernet connector).

  • Page 8: Replacing The Side Panel

    Replacing the side panel Align the tabs at the bottom of the side panel with the ridge on the bottom of the chassis. Place the side panel in the proper position on the chassis, and then slide it toward the front of the chassis. NOTE: There is a 3mm gap between the top of the side panel and the top of the chassis when the side panel is attached properly.

  • Page 9: Removing The Front Panel

    Removing the front panel This procedure is necessary only when removing or replacing an optical drive, memory card reader, HP Pocket Media Drive, or the hard disk drive. Remove the HP Personal Media Drive, if present. Pull the three tabs (B) away from the outside edge of the chassis. Swing the front panel to the left (away from the chassis) to remove it.

  • Page 10: Replacing The Front Panel

    Replacing the front panel Align the three hooks on the left side of the front panel with the three holes on the left side of the chassis, and then insert the hooks into the holes. Swing the front panel to the right (toward the chassis), and then press the three hooks on the right side of the front panel into the three holes on the right side of the chassis until the panel snaps into place.

  • Page 11: Locating Components Inside The Computer

    Locating Components Inside the Computer Memory card reader Upper 5.25-inch optical drive bay, which may be a CD-ROM, CD-RW, DVD-ROM, DVD+RW/+R, or combination drive Lower 5.25-inch optical drive bay, may be empty (knockout plate) or a CD-ROM, CD-RW, DVD-ROM, DVD+RW/+R, or combination drive HP Pocket Media Drive bay (select models) Front connector panel (no replacement instructions) HP Personal Media Drive bay (select models)

  • Page 12: Removing And Replacing Drives

    Removing and Replacing Drives Your computer has several drives that you can replace or upgrade. See “Locating Components Inside the Computer” on page 7 for the drive types and locations. The hard disk drive is either a Serial ATA (advanced technology attachment) drive, which uses a narrow data cable, or a Parallel ATA drive, which uses a wide data cable.

  • Page 13: Adding Or Replacing An Optical Drive

    Disconnect the power cable, data cable, and the sound cable, if present, from the back of the optical drive that you want to remove. For most drive cables, use a gentle rocking motion to remove the plug. For Serial ATA drive cables, press the latch (select models only) in the center of each plug, and then pull the plug out of the drive connector.
  • Page 14 Make sure the jumper on the new optical drive is in the CS (Cable Select) position. Your drive may vary from the illustration. Cable Select jumper Release the drive bay by pulling the latch out, away from the chassis, and then sliding the drive partway into the front of the chassis.

  • Page 15: Removing The Hp Pocket Media Drive Bay Or Hard Disk Drive

    Connect the power and data cables to the back of the optical drive that you want to add. Reconnect the sound cable, if present. Parallel ATA drive Serial ATA drive WARNING: If you are connecting a second Parallel ATA drive, make sure to connect the data cable labeled Master to the primary hard disk drive, and the data cable labeled Slave to the secondary hard disk drive.
  • Page 16 Disconnect the power and data cables from the back of the drive by squeezing the two latches on each and pulling the cable. Pocket Media Drive Parallel ATA drive Serial ATA drive Pull the drive out through the front of the chassis. Upgrading and Servicing Guide...

  • Page 17: Adding Or Replacing The Hp Pocket Media Drive Bay Or Hard Disk Drive

    Adding or replacing the HP Pocket Media drive bay or hard disk drive If replacing an existing HP Pocket Media Drive bay or hard disk drive, remove it. See “Removing the HP Pocket Media Drive bay or hard disk drive” on page 11. Slide the new HP Pocket Media Drive bay or hard disk drive into the front of the chassis until it locks into place.
  • Page 18 Connect the power and data cables to the back of the HP Pocket Media Drive bay or hard disk drive. Serial ATA drive Pocket Media Drive A — Connect to a primary hard disk drive. B — Connect to a secondary hard disk drive (select models only).

  • Page 19: Removing The Memory Card Reader

    Removing the memory card reader Prepare the computer to be opened, and then remove the side and front panels. See “Opening and Closing the Computer” on page 1. Release the drive by removing the screw on the top of the memory card reader, sliding the memory card reader to the left to loosen it, and then pulling it partway out of the front of the chassis.

  • Page 20: Adding Or Replacing The Memory Card Reader

    Adding or replacing the memory card reader Complete the procedures to remove the memory card reader, if necessary. See “Removing the memory card reader” on page 15. Slide the memory card reader partway into the front of the chassis. Attach the cables to the back of the memory card reader. Push the memory card reader into the chassis until the screw hole on the chassis is aligned with the screw hole on the top of the memory card reader, and then insert the short screw to secure the memory card reader to the chassis.

  • Page 21: Removing The Hard Disk Drive

    Removing the hard disk drive Prepare the computer to be opened, and then remove the side and front panels. See “Opening and Closing the Computer” on page 1. Gently lay the computer on its side. Remove the two screws that secure the hard disk drive cage to the chassis. Use a screwdriver to push down the latch on the side of the hard disk drive cage, and then slide the hard disk drive cage away from the bottom of the chassis.
  • Page 22 Lift the hard disk drive cage out of the chassis, and then remove the hard disk drive cables. For most drive cables, use a gentle rocking motion to remove the plug. For Serial ATA hard disk drive cables, press the latch (A) (select models only) in the center of each plug (B), and then pull the plug out of the drive connector.

  • Page 23: Adding Or Replacing A Hard Disk Drive

    Adding or replacing a hard disk drive If you are replacing an existing hard disk drive, remove it. See “Removing the hard disk drive” on page 17. Slide the new hard disk drive into the hard disk drive cage, making sure that the hard disk drive cables are facing the top of the drive cage.
  • Page 24 Align the four guides on the bottom of the hard disk drive cage with the four holes on the back of the chassis, and then slide the cage down toward the bottom of the chassis until it locks into place. Attach the hard disk drive cables.
  • Page 25 Attach the two screws that secure the hard disk drive cage to the chassis. Replace the front and side panels, and then close the computer. See “Opening and Closing the Computer” on page 1. Upgrading and Servicing Guide...

  • Page 26: Adding Memory

    Adding Memory Your computer comes with random access memory (RAM), which temporarily stores data and instructions on your computer. The computer is shipped with one or more memory modules installed, but you can replace the existing memory module(s) with higher-capacity modules.

  • Page 27: Removing A Memory Module

    Removing a memory module Prepare the computer to be opened, and then remove the side and front panels. See “Opening and Closing the Computer” on page 1. Gently lay the computer on its side. Remove the two screws that secure the hard disk drive cage to the chassis. Use a screwdriver to push down the latch on the side of the hard disk drive cage, and then slide the hard disk drive cage away from the bottom of the chassis.
  • Page 28 Locate the memory sockets on the motherboard. CAUTION: When handling a memory module, be careful not to touch any of the contacts. Doing so may damage the module. Move any cabling out of the way, if necessary. Push down the retaining clip on each end of the memory socket until the module pops out of the socket.

  • Page 29: Installing A Memory Module

    Installing a memory module Upgrade the memory in your computer with a memory module of the same type and speed as the memory originally installed in your computer. CAUTION: When handling a memory module, be careful not to touch any of the contacts.
  • Page 30 Align the four guides on the bottom of the hard disk drive cage with the holes on the back of the chassis, and then slide it down toward the bottom of the chassis until it locks into place. Attach the two screws that secure the hard disk drive cage to the chassis. Place the chassis upright.

  • Page 31: Removing Or Installing An Add-In Card

    Removing or Installing an Add-in Card An add-in card is a circuit board, such as a PCI, PCI-E, or AGP card, that fits into a computer add-in card slot. Your computer contains several add-in card slots that can be used to add components to your computer. The computer component configurations vary by model.

  • Page 32: Removing An Add-In Card

    Removing an add-in card Prepare the computer to be opened, and then remove the side and front panels. See “Opening and Closing the Computer” on page 1. Gently lay the computer on its side. On the back of the computer, remove the screw from the bracket cover for the add-in card slots, and then remove the bracket cover.
  • Page 33 Hold the add-in card at each end, and carefully rock it back and forth until the connectors pull free of the socket, and then remove the card. Be sure to not scrape the card against the other components. Store the old card in the antistatic packaging that contained your new card.

  • Page 34: Installing An Add-In Card

    Installing an add-in card Align the edge of the add-in card with the add-in slot on the chassis, and gently but firmly press the card straight down into the slot. The whole connector should be seated properly in the card slot. On the back of the computer, replace the bracket cover for the add-in card slots, and then install the screw.

  • Page 35: Replacing The Battery

    Place the chassis upright. Replace the side panel and close the computer. See “Opening and Closing the Computer” on page 1. NOTE: If the new card or device does not work, read the card manufacturer’s installation instructions and recheck all connections, including those to the card, power supply, keyboard, and monitor.
  • Page 36 Part number: 466917-001...

This manual is also suitable for:

M9340f - pavilion - eliteM9350f - pavilion - eliteM9360f - pavilion - eliteM9400f - pavilion - eliteM9402f - pavilion - eliteM9450f - pavilion - elite ... Show all

Table of Contents