How to update using a USB Mass-storage device Стр. 1 из 4 FIRMWARE UPDATING SOP of Firmware Upgrade ATV Firmware Upgrade - Com port Using USB to D-Sub 15 cable 1. COM Port and baud rate (9600 bps). 2. Select Read to load the file to be programmed into TV. 3.
How to update using a USB Mass-storage device Стр. 2 из 4 Working method Unlike the USB upgrade (to be mentioned later) the whole code in flash memory will be upgraded completely. This upgrade method can be done even the flash memory is blank. ATV Firmware Upgrade - USB 1.
Page 4
How to update using a USB Mass-storage device Стр. 3 из 4 should match to current upgraded model and total length of file name should be 23 characters, characters in red is not cared. Available file name, Continued Table 1. the file name of firmware for 703X series. Model Name File Name of BIN Code 19AV703X...
Page 5
How to update using a USB Mass-storage device Стр. 4 из 4 If USB flash memory is found, boot code will check if any available file name memory disk, if it is then the whole file with 2048K bytes (if it's a firmware) will be copied to DDR memory first.
Стр. 1 из 7 FUNCTION AND OPERATION Front Key Controls OSD operation for PC and TV OSD can be controlled by top control keypads or remote control. Function TV/video mode PC mode POWER Turn off/on the set Turn off/on the set "+"...
Page 7
Стр. 2 из 7 Timer ON: Green Timer OFF: No light OSD Menu To open the main menus (illustrated below), press MENU on the remote control or TV control panel. Picture Settings Active Backlight Control 3D Color management Picture Base Color adjustment MPEG NR Dual Bass...
Стр. 3 из 7 On timer position Teletext Panel lock Function Auto format 4:3 stretch Blue screen Side panel Remote Control file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.812\40L... 14.05.2015...
Page 9
Стр. 4 из 7 POWER: Press to turn on/off the TV from or to standby mode. VIDEO: 1. Press repeatedly to select the signal source. 2. The Source List should be activated and show on OSD 3. 1st press displays current, subsequent presses advance STILL: Press to do freeze function TEXT:...
Page 10
Стр. 5 из 7 2. Press the pass code to activate the factory mode 3. Press to activate the Channel Lock (enter PIN code for Channel lock) 4. If channel list OSD active - jump to that channel in the channel list ATV/DTV: VOL +/ –: Press to adjust the volume...
Page 11
Стр. 6 из 7 I/O connectors Rear connectors: Tuner input: RF connector for PAL/SECAM/NTSC 4.43 free air and cable reception. HDMI 1/2 input: Including digital video and audio. HDMI and PC mode share PC audio when system checks no audio header. SCART 1 input: Including RGB in, CVBS in TV out.
Стр. 7 из 7 Headphone output: 3.5 φ mini-jack Side AV input: CVBS with R/L audio in USB: Software upgrade, Media viewer (JPG, MP3) HDMI: Port included digital video and audio function file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.812\40L... 14.05.2015...
Handling the LCD Module Стр. 1 из 4 SAFETY INSTRUCTION Handling the LCD Module Safety Precaution In the event that the screen is damaged or the liquid crystal (fluid) leaks, do not breathe in or drink this fluid. Also, never touch this fluid. Such actions could cause toxicity or skin irritation. If this fluid should enter the mouth, rinse the mouth thoroughly with water.
Page 14
Handling the LCD Module Стр. 2 из 4 3. If the panel surface becomes soiled, wipe with cotton or a soft cloth. If this does not remove the soiling, breathe on the surface and then wipe again. If the panel surface is extremely solied, use a CRT cleaner as a cleaner. Wipe off the panel surface by drop the cleaner on the cloth.
Page 15
Handling the LCD Module Стр. 3 из 4 6. CMOS-LSI circuitry is used in the LCD module, so avoid damage due to static electricity. When handling the module, use a wrist ground or anchor ground. 7. Do not expose the LCD module to direct sunlight or strong ultraviolet rays for an extended period of time.
Page 16
Handling the LCD Module Стр. 4 из 4 10. When transporting the LCD module, do not use packing containing epoxy resin (amine) or silicon resin (alcohol or oxim). The gas generated by these materials can cause loss of polarity. file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.468\40L... 14.05.2015...
Стр. 1 из 4 INSTALLATION Channel Settings Initial setup The first time user switches on TV set, "initial setup" wizard will be shown in OSD menu to guide user to start channel scanning. The "channel scanning" takes several minutes. To stop the scanning, press the "EXIT"...
Стр. 2 из 4 3. Press "EXIT" to leave OSD menu. The skipped program number will not be found by pressing CH +/– key. Channel sort It will be automatically sorted after auto tuning. Channel name edit Press "MENU" on the remote control. Then select "Set up" → "Manual tuning", then follow OSD indication to edit channel name.
Page 19
Стр. 3 из 4 Disable TV Front/Side buttons except for input selector keys 3 Disable remote control Remote control works Disabled remote control. normally. (In Service Mode, not disabled) 4 Disable Setup Menu Setup menu is Setup menu is disabled. normally displayed.
Page 20
Стр. 4 из 4 Turn the TV on by power 1: 8sec button on the remote, then 2: 15sec a message ("Welcome to 3: until first operation our hotel") is displayed. (Until next operation (ex. Ch up) the message remains.) 11 TV to USB Save the data of TV settings to USB memory...
Стр. 1 из 4 SAFETY INSTRUCTION WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "SAFETY PRECAUTION" AND "PRODUCT SAFETY NOTICE" INSTRUCTIONS BELOW. Safety Precaution WARNING: SERVICING SHOULD NOT BE ATTEMPTED BY ANYONE UNFAMILIAR WITH THE NECESSARY PRECAUTIONS ON THIS RECEIVER. THE FOLLOWING ARE THE NECESSARY PRECAUTIONS TO BE OBSERVED BEFORE SERVICING THIS CHASSIS.
Page 23
Стр. 2 из 4 inflammability, voltage resistance, etc. therefore, use only replacement parts that have these same characteristics. Use only the specified parts when the mark is indicated in the circuit diagram or parts list. 7. Parts mounting and routing dressing of wirings should be the same as that used originally.
Page 24
Стр. 3 из 4 Resistance values in orms ( ). V: Voltmeter or oscilloscope (r.m.s. or peak reading) Input resistance : Input capacitance : 200 pF Frequency range : 15 Hz to 1 MHz and d.c. respectively Note: Appropriate measures should be taken to obtain the correct value in case of non sinusoidal waveforms.
Стр. 4 из 4 Product Safety Notice Many electrical and mechanical parts in this chassis have special safety-related characteristics. These characteristics are often passed unnoticed by a visual inspection and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc.
Стр. 1 из 4 SPECIFICATION Electrical Samsung 32 inch panel: Panel Model: LTA400HM02 Active Area: 885.6 mm (H) × 498.15 mm (V) Outline Dimension: 952.0 mm (H) × 551.0 mm (V) Pixel Pitch: 0.46125 mm (H) × 0.46125 mm (V) Pixel Format: 1920 ×...
Page 27
Стр. 2 из 4 TV RF input system: PAL/SECAM/NTSC 4.43 CVBS input: 1.0 Vpp (including 300 mV sync level), 75 Component video input: Y: 1.0 Vpp (include sync), PbPr: 700 mVpp, 75 Support 480i/p, 576i/p, 720p, 1080i at 50/60 Hz refresh rate.
Стр. 3 из 4 Backlight Contrast Brightness Color Tint Sharpness Black/White level High Middle Middle Picture Size There are 7 picture formats: Wide, 4:3, Super Live, Cinema, Subtitle, 14:9 and Native (HDMI only) mode. Note: 1. Panorama format is only available for 480i or 576i video mode. 2.
Page 29
Стр. 4 из 4 Impedance Speaker Others AV reset items include ... Picture and Audio back to factory setting Sleep timer: OFF, 15min, 30min, 45min, 60min, 90min, 120min TELETEXT (100 pages) TELETEXT ON/OFF SUBPAGE INDEX SUBTITLE HOLD (Stop acquisition) REVEAL (Show hidden information) TELETEXT MIX TELETEXT ZOOM file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.495\40L...
Page 42
IF_5V Close to Tuner IF_5V TU1301 TU1301 +5V_IF_1 Close to IC 120Ohm/100MHz 120Ohm/100MHz R1332 R1332 33Ohm 33Ohm FB1303 FB1303 L1302 L1302 R1307 R1307 FB1302 FB1302 C1302 C1302 R1303 R1303 680OHM 680OHM 0.82UH 0.82UH 120Ohm/100MHz 120Ohm/100MHz 6.8KOhm 6.8KOhm 10NF/50V 10NF/50V TT212X TT212X R1304 R1304...
Page 43
Pre/De OC_S3 OC_S2 OC_S1 OC_S0 Vswing (mV) EQ_S0 EQ_S1 emphasis (dB) -9.5 Port 1 15dB on all high speed data inputs OC_S0 OC_S1 OC_S2 OC_S3 EQ_S0 EQ_S1 -3.5 Port 2 3dB on all high speed data inputs 1000 Port 3 8dB on all high speed data inputs R2346 R2346...
Стр. 1 из 2 SCHEMATIC DIAGRAM Precaution WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "X-RAY RADIATION PRECAUTION" FOR DIRECT VIEW CTV ONLY, "SAFETY PRECAUTION" AND "PRODUCT SAFETY NOTICE" OF THIS MANUAL. CAUTION: The international hazard symbols " " in the schematic diagram and the parts list designate components which have special characteristics important for safety and should be replaced only with types identical to those in the original circuit or specified in the parts list.
Page 54
Стр. 2 из 2 = Electrolytic capacitor = Mylar capacitor 3. The parts indicated with " " have special characteristics, and should be replaced with identical parts only. 4. Voltages read with DIGITAL MULTI-METER from point indicated to chassis ground, using a color bar signal with all controls at normal, line voltage at nominal AC volts.
Page 56
Search Parts No. : Block Location Parts No. Description Electric Parts E200 75018812 PC BOARD ASSY, MAIN, 40LV703R, 69EB3JM11C05P Electric Parts E250 75018813 POWER MODULE, OPENFRAME 244W/+5 12 24V, 0433-002H000 Electric Parts E260 75018685 PC BOARD ASSY, KEY, 32AV703G, 69EB3IK10B02P...
Page 57
Стр. 1 из 1 PARTS LIST All Block Block : Search 6 / 34 Jump Page : Location : Search Parts No. : Block Location Parts No. Description Packing E512 75018824 EPS CUSHION, 40LV703G(BR), 1505-017N000 Packing E513 75018825 EPS CUSHION, 40LV703G(BL), 1505-017P000 Packing E520 75018826 EPE BAG, 40LV703G, 1516-011E000...
Page 58
Стр. 1 из 2 PARTS LIST Precaution WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "SAFETY PRECAUTION" "PRODUCT SAFETY NOTICE". CAUTION: The international hazard symbols " " in the schematic diagram and the parts list designate components which have special characteristics important for safety and should be replaced only with types identical to those in the original circuit or specified in the parts list.
Page 59
Стр. 2 из 2 : Fusible Resistor All CD and PF capacitors are ±5 %, 50 V and all resistor, ±5 %, 1/6 W unless otherwise noted. file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.595\40L... 14.05.2015...