Page 1
SUZUKI LED TV SERVICE MANUAL Model Nam e: SZTV-32LED6 A Ver si on NO : The release of this document is under controlled by the company. Any extra copy of this document must be written permission by the product manager.
Re vision N o. Re vision Da t e Pa ge Re a son De sc ript ion V 1 .0 2 0 1 2 .1 1 .3 0 I nit ia l Re le a se CHAPTER 1: WARNING...
Page 4
This service information is designed for experienced repair technicians only and is notdesigned for user by the general public.It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.Products powered by electricity should be serviced or repaired only by experienced professional technicians.Any attempt to service or repair the product or products dealt within this service information by anyone else could result in serious injury or death.
CHAPTER 2: SAFETY PRECAUTIONS 2-1. CAUTION: No modification of any circuit should be attempted. Service worker should only be performed after going through to familiar with all of the following safety checks and servicing guidelines. 2-2. SAFETY CHECK Care should be taken while servicing this TV display. Because of the high voltage is used in the inverter circuit.
Page 6
Product Rough Specification TV ID GSTCG1 Pnael Model A320BD1WX2-5 Main Board Model TP.VST59.P83A General Power model Information Power Consumption(Stand-by Mode) <0.5W Power Consumption(MAX) Power Input Voltage 110-240V~ Power Rated Input Freq 50/60Hz±5% Video System PAL ;SECAM Sound System BG;DK,I,L/L' ;NICAM/A2 Max Storage Channel 199CH Teletext...
Page 7
CHAPTER 4: MAIN BOARD CONNECTION 5-1: Main Board TOP View 5-2: Main Board Botton View 5-3: Main Board Connection...
CHAPTER 5: EASY TROUBLE SHOOTING 7.1 Troubleshooting for Common Use Note: Before opening the cabinet and working on the repairs, please read the troubleshooting and Q&A attached in theuser’s manual, which has covered most of the problems caused by unproper using or settings to the TV set.
Page 12
because the failure in power on can lead to a no-display problem. No display (including white screen, black screen, etc.) Note: If the troubleshooting given below can not help you, change the LCD panel for a try. But we strongly suggest regard changing the panel as the last step of fixing the display problem.
Page 13
can also lead to audio problem. 7.4 Troubleshooting for Keyboard Check the wire between mainboard and keyborad, watch if there is fracture or cladding material breakage. No key can work Check the joint of mainboard and keyboard wire, watch if there is poor soldering ofrfake solder. Check the resistances that locate on the keyboard PCB.
Page 14
left-right channel wire fault for audio). Check the LED assembling, watch if its pins are in wrong location. Check the other components of RC board are wrong or bad.That is usually caused by bad keyboard, change it for a try. There is a reacting delay when operating the keys Check the keyboard to see whether there is a short circuit between each soldering joint.
Page 29
CHAPTER 8: FIRMWARE UPDATE 9-1: USB Update: 1, First update to the USB into the software inside , Then insert the TV , Red and green LED lights flash and other end , Successful software update, If update fails,piease use 11-1 means 9-2:...
Page 31
6 Turn on the main board or the TV set , click the connect picture, link target board. Chart(3、4) 6.1 If link successfully, then display the dialog as follow ,please click “OK” ,and continue Chart(5) 6.2 If link unsuccessfully, then display the dialog as follow ,please click “OK”, and check the related operation Chart(6)...
Page 32
6.3.1 course forUPdate As shown below: Chart(8) 6.3.2 successful Update Chart(9) 6.3.3 If update fails, try starting from the 4 update The End...