Dantherm Flexibox 460 Quick Setup Manual
  1. Manuals
  2. Brands
  3. Dantherm Manuals
  4. Fan
  5. Flexibox 460
  6. Quick setup manual
Dantherm Flexibox 460 Quick Setup Manual

Dantherm Flexibox 460 Quick Setup Manual

Hide thumbs
Table of Contents

Quick Links

Flexibox 460 / 810
Quick setup guide
Rev. 1.1
Table of Contents
loading

Related Manuals for Dantherm Flexibox 460

Summary of Contents for Dantherm Flexibox 460

  • Page 1 Flexibox 460 / 810 Quick setup guide Rev. 1.1...
  • Page 2 • Proper work attire (long sleeve shirt and long pants) Please strictly observe the following: Special Skill is required to install the Dantherm Flexibox units. Non-qualified personnel should not attempt any of the actions shown in this installation guide. Dantherm shall not be responsible for improper installation or any accidents, damage, or...

  • Page 3: Tools Needed

    Tools needed 5 mm 8 mm 4 mm 3 mm 2 mm...
  • Page 4 Product dimension 460 / 810 503 mm 19,7 inch 500 mm 19,7 inch 758 mm 29,9 inch 455 mm 472 mm 18 inch 18,6 inch Product overview indoor view Earth connection Main PCB with connections Incoming air flow Incoming air flow...
  • Page 5 Product overview Exploded fan/controller Intregreted rainhood Installation bracket Shelter air supply Airflow outside air inlet front Safety grill Filter Filter lock 460 versus 810 Flexibox 460 Flexibox 810...

  • Page 6: Prepare Unit

    Prepare unit Cut hole Warning Caution 430 mm (17 inch) 225 mm (8,9 inch) minimum 900mm (35,5 inch)

  • Page 7: Mount Bracket

    Mount bracket Center Mount unit...
  • Page 8 Seal unit Mount damper Flexibox dampers Quick setup guide Rev. 1.0...
  • Page 9 Mount indoor sensor Keep clear Connect earth To shelter earth...

  • Page 10: Mandatory Connections

    Mandatory connections Warning Caution 48V DC negative 48V DC supply 2x2,5¤mm 48V DC positive 0” AWG 13 External safety breaker 48V DC -16A fused NOT included 2,5 mm wires (AWG 13) Indoor sensor Room sensor 0” AL 2 0” AL 1 Damper Belimo LM72 (if motorized)
  • Page 11 Mount display (accessory) 8 mm 4 mm 3 mm...

  • Page 12: Changing Parameters

    Display Type CC4 Flexibox Room temperature 29°C Operation mode Cooling setpoint 28°C CC4 Combo 29°C Mode Description Free cooling 28°C Active cooling Warning Heat Caution Alarm Changing parameters Selection Menu active cursor cursor Cool SetPt [24 Cool SetPt [24 Temp in C° CC4 Combo CC4 Combo Heater SetPt:10...

  • Page 13: Advanced Parameters

    Advanced parameters °Dantherm Air Handling A/S., Skive, 7800 DENMARK Controller - CC4 SW Ver - 0.4e ----------------------------------------------------------- CC4 Configuration SW 2013.02.11 ----------------------------------------------------------- Device: Flexibox 810, 368453 ----------------------------------------------------------- Cooling Fan Configuration Fan 1 Fan 2 Fan 3 1.OFF Temp [xT0][-40-80]: 20.0 :0.0...

  • Page 14: Optional Connections

    Optional connections Warning External safety breaker Caution (not included) 48V DC negative 48VDC Mini blade terminal. 16A fused 48V DC positive ittlefuse” type ”997 010” 2,5 mm -t° Mini blade terminal. Room sensor ittlefuse” type ”997 010” Factory jumper Factory jumper 0 / 12V DC AL 2 with pull up...
  • Page 15 Dantherm can accept no responsibility for possible errors and changes. Irrtümer und Änderungen vorbehalten. Dantherm n’assume aucune responsabilité pour erreurs et modifications éventuelles. Dantherm se exime de cualquier responsabilidad por errores y cambios realizados.
  • Page 16 Dantherm Air Handling A/S Marienlystvej 65 7800 Skive Danmark www.dantherm.com [email protected]...

This manual is also suitable for:

Flexibox 810

Table of Contents