RTS EKP-32 User Instructions
  1. Manuals
  2. Brands
  3. RTS Manuals
  4. Intercom System
  5. EKP-32
  6. User instructions

RTS EKP-32 User Instructions

Digital matrix series keypanel; expansion panel; level control panel
Hide thumbs Also See for EKP-32:
Table of Contents

Quick Links

See also: User Manual
U
I
SER
NSTRUCTIONS
KP-32 K
EYPANEL
EKP-32 E
P
XPANSION
ANEL
LCP-32 L
C
P
EVEL
ONTROL
ANEL
9350-7656-000 Rev K
9/2006
Table of Contents
loading

Related Manuals for RTS EKP-32

Summary of Contents for RTS EKP-32

  • Page 1 NSTRUCTIONS KP-32 K EYPANEL EKP-32 E XPANSION ANEL LCP-32 L EVEL ONTROL ANEL 9350-7656-000 Rev K 9/2006...
  • Page 2 OTICE The product information and design disclosed herein were originated by and are the property of Telex Communications, Inc. Telex reserves all patent, proprietary design, manufacturing, reproduction, use and sales rights thereto, and to any article disclosed therein, except to the extent rights are expressly granted to others.

  • Page 3: Table Of Contents

    EKP-32 Expansion Keypanel........
  • Page 4 Talk + auto table ............3-4 All Call Key .
  • Page 5 MENU SYSTEM, KEY ASSIGN MENU......... . . 6-3 General Procedure to use the Key Assign Menu .
  • Page 6 KP9X Autodial Sequences ..........7-3 Storing an Autodial Number in the TIF-951 .

  • Page 7: Introduction

    Description Figure 1.1 KP-32 keypanel front view.. The RTS™ Model KP-32 Keypanel fits in a standard 19" rack and is two rack spaces high. It has 32 lever keys: 30 keys are for intercom talk/listen assignment; one key is for call waiting response;...

  • Page 8: Options

    • Only 90 mm deep behind the front panel (approximately 130 mm with connectors): Perfect for consoles, OB vans, etc. • Digital Signal Processing (DSP): Improves microphone voice activation and limiting. Adds new mixing, metering, and filtering capabilities. • Binaural (5-pin) Headset Connector: Works with the DSP mixing feature. Lets you independently assign intercom, microphone, and program audio to left or right headphone.

  • Page 9: Ekp-32 Expansion Keypanel

    EKP-32 Expansion Keypanel Figure 1.4 EKP-32 expansion keypanel front view. Provides and additional 32 intercom keys for a total of up to 64 keys (62 intercom keys total). LCP-32/16 Level Control Panels LCP-32/16 level control panel front view. Figure 1.5 Provides easy adjustment of point-to-point and party line listen levels for individual intercom keys.
  • Page 10 This Page Left Blank Intentionally K P - 3 2 U s e r M a n u a l...

  • Page 11: Installation

    E C T I O N NSTALLATION HAPTER Option DIP Switch Settings Switch 1: Latch Enable/Disable Default setting = Open: Enable. Description: An intercom key can always be turned on for momentary conversation by pressing and holding the key during the conversation. There is also an electronic latching feature that lets you tap intercom keys to turn them on or off.

  • Page 12: Switch 4: Call Flash Timeout

    Switch 4: Call Flash Timeout Default setting = Open: 15 Second Flash. Description: Whenever there is an incoming call and there is a talk key assigned to the caller, the talk LED next to that key will flash. The flash can be set for 15 second timeout, or until the caller's talk key is released.

  • Page 13: Address Setting For Zeus

    Address Setting for Zeus Intercom port connectors on the Zeus back panel are arranged in three groups of eight intercom ports. For each group, intercom port connectors are labeled ID 1, ID 2, etc. When you connect a KP-32 keypanel to Zeus, set the Address switch to match the corresponding ID number on the Zeus back panel.

  • Page 14: Adam Cs With 50-Pin Telco Back Panel

    Address number vs intercom port numbers for 8-Port Audio I/O Cards (ADAM AND ADAM Figure 2.1 CS Intercom Systems. ADAM CS with 50-pin Telco back panel: Determine the address setting from Figure 2.1. To use the table, locate the intercom port number to which the KP-32 will be connected.

  • Page 15: Address Setting For Adam

    Each LCP-32/16 adjusts the listen levels for 16 keypanel keys, and you can connect as many LCP-32 panels as required to adjust all keys on the KP-32 and on an optional EKP-32 Expansion Panel. An interconnect cable is supplied with each LCP-32. Connect the first LCP-32 to the LCP connector on the KP-32.

  • Page 16: Power Supply Connector

    RJ12 Intercom Cable Wiring Figure 2.3 Power Supply Connector Align and insert the external power supply connector. Tighten the locking ring. Connect a power cord to the power supply and to an AC power source. The power supply accepts 100-240 VAC, 50/60 Hz.

  • Page 17: Panel Microphone Gain Adjustment

    Microphones. Insert the microphone and rotate the entire microphone body several turns to lock in place. Panel Microphone Gain Adjustment The gain of the panel microphone preamp can be adjusted via the recessed trim pot located on the back panel. Turn the pot clockwise to increase gain and counter-clockwise to decrease gain. The limits are ±20 dB from nominal.
  • Page 18 This Page Left Blank Intentionally K P - 3 2 U s e r M a n u a l...

  • Page 19: Basic Operation

    Screen Saver Operation If the KP-32 is set for screen saver operation, the alphanumeric display automatically shuts off after several minutes of inactivity. The display reactivates on incoming call or when the keypanel operator actuates any control. DIP switch 3 enables/disables screen saver operation. You can override the normal timeout period for screen saver operation and immediately place the Note keypanel in screen saver mode.

  • Page 20: Intercom Keys And Displays

    Intercom Keys and Displays Alphanumeric Display Indications for Intercom Keys Upper Case Letters: Upper case letters indicate keys that have any kind of talk assignment, with or without a corresponding listen assignment. Example: Lower Case Letters: Lower case letters indicate keys that have only a listen assignment. Example: dir1 Dashes : Dashes indicate a key that has no talk or listen assignment.

  • Page 21: Flashing Green Talk Led & Display Alpha (On Time Equal To Off Time)

    at the remote location if your keypanel has the lower trunk IFB priority. IFB trunk priorities are set in ADAMedit. (Click the "KP" button on the ADAMedit toolbar to access Keypanels / Ports setup, then click the "Edit" button, then click the "Advanced" tab. Enter the desired IFB priority in the fields provided.

  • Page 22: Talk + Auto Reciprocal

    Talk + auto reciprocal Listen will always be on, and talk may be turned on or off. Talk + auto table If an IFB talk key has an auto-table listen assignment, talk and listen can be independently activated. The listen key listens to whatever is defined as the IFB Listen Source for the IFB that is assigned to the talk key.

  • Page 23: Muting The Microphone

    click the "Advanced" tab. Place a check next to "Port is TIF". Remember to send the change to the intercom system.) Muting the Microphone Tap the MUTE key to turn microphone muting on or off. The Vol. Sel. display alternates between microphone is muted.
  • Page 24 This Page Left Blank Intentionally K P - 3 2 U s e r M a n u a l...

  • Page 25: Telephone Operation

    Telephone operations require an optional TIF-951 Telephone Interface. Also, you must first Note assign an intercom key to talk/listen to the TIF. We recommend a talk+auto listen assignment. Receiving A Phone Call When there is an incoming telephone call, the talk LED will flash red next to the KP-32 key that is assigned to the TIF.

  • Page 26: Kp9X Redial Sequence

    Dial the telephone number. Digits scroll in the display above the TIF key. When the far end answers, you can dial additional digits (to access a mail system or automated response system, etc.). When finished dialing, momentarily turn off the TIF talk key to end dialing mode (talk LED turns red).

  • Page 27: Dialing An Autodial Number Stored In The Tif-951

    Dialing an Autodial Number Stored in the TIF-951 Tap the PHONE key to activate dialing mode. Tap "down" on the TIF talk key to latch it in the on position. Tap CLR followed by the autodial number (01, 02, etc.). When finished dialing, click the PHONE key again to exit dialing mode.

  • Page 28: Autodial

    After the far end answers, you may dial additional digits (to retrieve voice mail, log onto an Note automated answering system, etc.). 5 If there is no answer, or to hang up when finished talking, tap PGM to hang up. Occasionally, you may receive intercom an intercom caller name in the Call waiting window Note while you are talking on the phone.

  • Page 29: Kp9X Series Keypad Programming

    KP9X S HAPTER A summary of the keypad programming sequences is located at the back of the manual for quick Note reference. KEYPAD PROGRAMMING, DISPLAY REQUESTS Display requests let you view information about the keypanel configuration. You can display information by two methods: either by entering sequences on the programming keypad, or by scrolling the names of display requests in the Call waiting window and then selecting the desired display request.

  • Page 30: Display Setup Page Assignments

    Additional setup pages are assigned to any connected expansion panels, and are referred to as "Expansion 1", "Expansion 2", etc.). Since the KP-32 requires 2 setup pages, it uses the main page assignments and also one expansion page (Figure 5.1). The EKP-32 uses two additional expansion pages.

  • Page 31: Tone Generator Activation (Func-Display-7)

    PGM: Displays setup page assignments. Epnl key. =EKP-32 bottom row keys. PGM: After selecting this item, tap up on any listen key with a point-to-point or party line Gain assignment. The current listen gain from this keypanel to the intercom port or party line displays in the Call waiting window.

  • Page 32: Keypad Programming, Assigning Intercom Keys

    • The same setup page cannot be assigned in more than one place. If a setup page is already Notes assigned somewhere else, you must clear or change that assignment first. With the exception of the main row assignment, you can clear any page assignment from a row of keys by entering E-PNL 0 PGM, then pressing any key in the row.

  • Page 33: Programming Key Assignments Using Copy

    3 Auto mute (listen keys only) 4 Auto reciprocal (listen keys only) 5 All call (talk level 1 only) 6 DIM (talk level 2 only, for point-to-point key, must enter 00 first) 7 Auto table (listen only, when talk level 1 is an IFB assignment) 4 Trunked intercoms only: (Skip when assigning auto functions or local key assignments.) Select an intercom matrix (tap 1 , or 2 etc.).

  • Page 34: Programming Key Assignments Using Alpha Scrolling

    If a key will not accept an assignment, the destination that you are trying to assign may not have Note scrolling enabled in ADAMedit. Or, the key that you are trying to assign may be restricted in ADAMedit. Programming Key Assignments Using Alpha Scrolling Alpha scrolling lets you scroll through a list of names of ports, party lines etc.

  • Page 35: Clearing A Key Assignment

    Tap down on an intercom key to assign talk, or tap up to assign listen. Clearing a Key Assignment There are two ways to clear a key assignment: Method 1: Clearing the Call waiting Window and Copying it to a Key Clear the Call waiting window, if necessary, by tapping up one or more times on the Call waiting key.
  • Page 36 This Page Left Blank Intentionally K P - 3 2 U s e r M a n u a l...

  • Page 37: Menu System

    A chart of the menu system is located at the back of the manual for quick reference. Note MENU SYSTEM, MENU ACCESS Clear all names from the Call waiting display (if not clear) by tapping "up" one or more times on the Call waiting key.

  • Page 38: Display Menu, Chans On

    • AC: All-call key. For descriptions of the various key assignment types, see the "GLOSSARY". Note Display Menu, Chans On Displays an alpha list, in the Call waiting window, of all intercom ports that currently have talk crosspoints closed to this keypanel. Chans On is typically used to locate an open mic or other open audio source that needs to be shut off.

  • Page 39: Menu System, Key Assign Menu

    MENU SYSTEM, KEY ASSIGN MENU Use this menu to assign intercom keys, to adjust listen levels for point-to-point keys and party line keys, and to assign setup pages. General Procedure to use the Key Assign Menu Clear the Call waiting window if necessary, by tapping upward one or more time on the Call waiting key.

  • Page 40: Key Assign Menu, Matrix

    8 When the requested list is displayed, press ⎠⎠ or 9 Tap PGM or FWD to select the assignment. should now display in the Call waiting window. Press ⎠⎠ or Talk Lvl 1 select a different option. Options are as follows: •...

  • Page 41: Key Assign Menu, Party Line

    Key Assign Menu, Party Line Assigns a key that talks and/or listens to a party line. The key will have no effect until members have been assigned to the party line in ADAMedit. Note that party lines members are usually non- keypanel devices that cannot activate talk and listen paths.

  • Page 42: Key Assign Menu, Key Gain

    • Auto Mute (AM, for listen keys only) • Auto Recip (AR, for listen keys only) • All Call (AC, for talk level 1 only) • Dim ( Dim Table function, for talk level 2 on point-to-point keys only) Press FWD or PGM to select the desired auto function. displays.

  • Page 43: Key Assign Menu, Setup Page

    Key Assign Menu, Setup Page Use this menu item to change the setup page assignments on the KP-32 or EKP-32. One setup page is used for the top row of keys, and another setup page is used for the bottom row.

  • Page 44: Removing The Chime Option From A Key

    Tap any keys where you want to add a chime tone. Both LEDs will light red for the selected keys. Tap CLR to exit. Run Service Menu, Save Cfg, to store Chime settings. The chime option will continue on a key even if you change the key assignment. Note Removing the chime option from a key Repeat the procedure to add chime, but tap any keys where the LEDs are lit red to turn them off.

  • Page 45: Key Option Menu, Solo

    Key Option Menu, Solo A solo key will cause all other keys to turn off when activated. You can assign one solo key. Select then tap PGM. Solo displays. Tap Key Tap a key. Both LEDs for the key will light red to confirm the assignment. Tap the key again if you made a mistake and want to remove the assignment.

  • Page 46: Caller Vol

    Auto Baud displays. To select the baud rate, press ⎠⎠. The choices are Auto Baud, 9600 Baud, or 76.8 Baud. Tap PGM to select the baud rate. Tap CLR to exit when finished. The new baud rate is now set. Run Service Menu, Save Cfg to store the Baud Rate setting.

  • Page 47: Service Menu, Dsp Func

    : Good when ambient light is bright. Bright : Recommended only for very bright ambient light, such as outdoors. Uses maximum Maximum power and decreases display life. : Overrides the normal screen saver timeout period and immediately places the Scr Saver keypanel in screen saver mode.

  • Page 48: Metering

    Microphone Matrix Aux 1 Aux 2 Tap PGM. displays. Gating Tap PGM. ♦ displays. The arrow indicates that gating is now selected. Gating Tap CLR to exit. Run "Service Menu, Save Cfg", to save the change. Metering Metering lets you use the Vol. display as an LED bar graph meter to monitor an audio signal for about 1 minute.

  • Page 49: Service Menu, Hdst Sel

    Figure 6.1 For example, you may not want to use LCP-32s with the KP-32 but do want to use them with an EKP-32. In this case, you must turn off LCP usage for keys 1-32 as follows: Select , then tap PGM.

  • Page 50: Service Menu, Local Gpio

    Tap CLR to exit. Run "Service Menu, Save Cfg", to store the new LCP-32 settings. Service Menu, Local GPIO If your KP-32 has an optional Connector Module, you can use this menu item to assign the GPIO inputs and outputs. Inputs can be assigned to activate intercom keys (including group master keys and a solo key).

  • Page 51: Adding Or Removing A Gpi Output Key Assignment

    Press ⎠⎠ or if necessary to select Tap PGM. Press ⎠⎠ or .to display the GPI input that you want to remove. Tap PGM. Press ⎠⎠ to select Not Asgnd Tap PGM. ♦ displays. The arrow indicates that "Not Assigned" is the new selection. Not Asgnd Tap CLR to exit.

  • Page 52: Service Menu, Min Volume

    ADAMedit, appear to be in the wrong positions on the keypanel or expansion panel. The KP-32 and EKP-32 use module ID numbers (Mod ID numbers) to define the address of each key and display module. See Figure 6.2. By default, Mod 1 is always assigned to the right half of the KP-32 and this never changes, since this module has the keypad and is unique.

  • Page 53: Service Menu, Output Level

    Mod ID assignments for the KP-32 and EKP-32. Figure 6.2 You do not need to run Save Cfg after changing Mod assignments. Note Service Menu, Output Level Allows the adjustment of the nominal audio output level to the matrix from 0 dB to +8 dB.

  • Page 54: Service Menu, Reset Cfg

    Service Menu, Reset Cfg Reset Cfg restores all custom settings to the defaults and erases all stored autodial numbers. Service Menu, Save Cfg PGM saves custom settings that you have made in the Key Option or Service menus. Save Cfg made in the After customizing settings in the Key Option and Service menus, run Save Cfg to store your custom settings in non-volatile memory.

  • Page 55: Kp9X Keypad Sequence Quick Reference

    PGM: Turn on tone generator. CLR to end. Tone PGM: Display setup page assignments. Epnl =EKP-32 top row keys. PGM: Port / party line listen gain. Turn on listen key. ⎠⎠ or Gain PGM: Reset all port / party line gains to 0dB.

  • Page 56: Key Assignments Using Keypad Numeric Entry

    Tap PGM. Tap any key in top row to assign page to top row. Tap any key in bottom row to assign page to bottom row. KEY ASSIGNMENTS USING KEYPAD NUMERIC ENTRY For talk level 2 assignment only: Tap 0 Select the key assignment type: NUM Intercom port.

  • Page 57: Kp9X Dial Sequence

    KP9X Dial Sequence Activate the TIF listen key (listen LED green). Make sure the TIF talk key is off (Talk LED off). On the keypad, tap CLR-PHONE-PGM. Activate the TIF talk key (talk LED turns green). The "ON" LED at the TIF-951 will activate, and you should hear dial tone at the KP-32.
  • Page 58 This Page Left Blank Intentionally K P - 3 2 U s e r M a n u a l...

  • Page 59: Specifications

    Microphone Preamplifier Electret Mic Input Level @ 1 kHz: Dynamic Mic Input Level @ 1 kHz: Output Level (to matrix): Max Voltage Gain, Mic to Line: Frequency Response: Limiter: Tone Generator Output Level (to matrix): Output Frequency: Headphone Amplifier Maximum Voltage Gain: Frequency Response: Headphone Impedance: Output Power:...

  • Page 60: Intercom Input/Output

    Speaker Rating: Intercom Input/Output Input: Output: External Line Input: (Program Input) Input Level General AC Supply: External, switching type, 100-240 VAC, 50/60 Hz with locking DIN connector for attachment to the keypanel and universal IEC connector for connection to various AC mains cords Environmental: Storage: Operating:...

  • Page 61: Power Input Connector

    Power Input Connector Type: Pin-out: Intercom Connectors: Parallel-wired DE9S and RJ12 Connectors Type: Pin-out: Type: Pin-out: Expansion Connector Type: LCP Connector Type: Pin 4: Headphone left high Pin 5: Headphone right high 5-pin locking DIN Pin1: Common Pin2: Common Pin3: +5VDC, 1.50A Max. Pin4: -15VDC, 0.150A Max.

  • Page 62: Gpi Module Conntectors (Optional)

    GPI Module Conntectors (Optional) Aux 1 In (Auxiliary program input 1) Type: Pin-out: Aux 2 In (Auxiliary program input 2) Type: Pin-out: Balanced input, +8dBu nominal Notes Relay 1 & 2 Out Type: Pin-out: Relay 3 & 4 Out Type: Pin-out: K P - 3 2 U s e r M a n u a l 3-pin female XLR...

  • Page 63: Opto 1-4 In (Opto-Isolated Control Inputs)

    The relay 1 and 2 contacts are electrically separate, but operate in unison. The relay 3 and 4 Notes contacts are electrically separate, but operate in unison. The +5 VDC pins are connected internally through 1K resistors to +5 VDC and can source 5 mA. This voltage can be used with the relay contacts to create an active high output for some devices that require a +5 VDC signal to activate.

  • Page 64: Foot Switch/Speaker

    Mic input -60 dBu nominal. Headset out 0.325 watts into 8 ohms. Note Foot Switch/Speaker Type: Pin-out: A switch contact closure from the footswitch input to ground will activate the footswitch input. Note MIC In (J7) Unbalanced Panel Microphone Input Type: Pin-Out: Input level -42.5 dBu nominal.

  • Page 65: Menu Access

    KP-32 M HAPTER MENU ACCESS Clear all names from the Call waiting display (if not clear) by tapping "up" one or more times on the Call waiting key. Tap MENU to activate the menu system. Press ⎠⎠ to scroll forward through the list of menus. Press Tap FWD or PGM to enter a menu.
  • Page 66 This Page Left Blank Intentionally K P - 3 2 U s e r M a n u a l...

  • Page 67: Mode 2 Operation

    Section 2 Switch 4: Call Flash Timeout* When the switch is closed the menu and indefinite talking is disabled. Switch 5: Footswitch Enable / Disable* Amber talk LEDs indicate a latched talk key. Section 3 LED Indications for Intercom Keys Talk LED Indications The talk LED is the lower LED for each key.

  • Page 68: Solid Red Talk Led & Flashing Display Alternating Pattern Of Alpha & (-**-) ("Busy")

    Solid Red Talk LED & Flashing Display Alternating Pattern of Alpha & (-**-) ("Busy") You cannot talk at this time. This indication occurs when you activate a local IFB key that is already in-use by a keypanel with a higher IFB priority. It also occurs when you activate any key assigned to a remote destination, but there are currently no trunks available.

  • Page 69: Glossary

    For talk key assignment only. Activating an All Call key will also activate all talk keys to the left All Call of the All Call key (up to, but not including another All Call key). Alphas are the user-changeable names which identify destinations (intercom ports, party lines, Alpha etc).
  • Page 70 The term "Crosspoint", like the term "Matrix" is inherited from intercom systems, such as the Crosspoint RTS CS9500, CS9600, and CS9700, that use a switching matrix to route intercom audio. In those systems, the crosspoints are the actual switches that close or open to connect or disconnect talk and listen paths.
  • Page 71 music can be interrupted while someone is talking over the PA.IFB's are set up by defining the IFB inputs and outputs using the intercom system configuration software. The intercom output port is called the IFB output and the program input port is called the IFB input. IFBs can also be given names which are meaningful to keypanel operators.
  • Page 72 button in ADAMedit, then press F1 on the computer keyboard if you need help.)Intercom Data Groups and Port Number CalculationFor data routing purposes, port numbers are arranged in groups of 8 sequential intercom ports. In an ADAM or ADAM CS Intercom System, each Audio I/O card comprises one data group.
  • Page 73 Talk level 1 is the normal talk key assignment. This is the assignment that normally appears in the Talk Level 1 alphanumeric display (on keypanels so equipped). You may add a talk level 2 assignment to activate a second device along with talk level 1. Talk level 2 is used with stacked talk keys.
  • Page 74 This Page Left Blank Intentionally 11-6 K P - 3 2 U s e r M a n u a l...
  • Page 75 RVON-1 for the KP-32 and KP-812 Family of Keypanels APPENDIX A 93507757000 Rev F June 2006...
  • Page 76 OTICE The product information and design disclosed herein were originated by and are the property of Telex Communications, Inc. Telex reserves all patent, proprietary design, manufacturing, reproduction, use and sales rights thereto, and to any article disclosed therein, except to the extent rights are expressly granted to others.
  • Page 77 RTS™ Matrix Intercom. The RVON-1 card is configurable through the keypanel service menu and Telex’s AZedit configuration software. It is also fully compatible with internationally recognized standards and supports the following protocols: G.711, G.729 AB, and G.723 (2 bit rates).
  • Page 78 Introduction Specifications DIGITAL Compression Audio Bit Rate G.711 G.729AB G.723 5.3k/6.3k *Data depends on CODEC selection. NOTE: The Playout Delay and Bandwidth depend on the configured amount of audio per packet. CONNECTIONS • RJ-45 Ethernet via backcard • 14-pin KP Compatible Expansion Connector Pin 1...

  • Page 79: Dip Switches

    Dip Switches Dip Switches Switch 1 Reserved Switch 2 Disable Telnet Shell Default Setting: OFF (Telnet Enabled) Description: The Telnet shell allows you to access configuration options through the use of Telnet. When DIP switch 2 is OFF, you can use Telnet to access configuration options on the RVON-1 card. Turn DIP switch 2 ON to disable the Telnet shell Switch 3 Enable Boot Downloader Default Setting...

  • Page 80: Flash Chip Replacement

    Introduction Flash Chip Replacement KP-32 Standard KP-32 (Japan) KP-632 KP-832 TABLE 2. Flash Chip placement on the KP-32 motherboard Figure 1. Keypanel Flash Chip Replacement 9015-7656-002 (U2) 9015-7656-003 (U3) 9015-7656-042 (U2) 9015-7656-043 (U3) 9015-7656-202 (U2) 9015-7656-203 (U3) 9015-7656-302 (U2) 9015-7656-303 (U3) Flash Chip replacement part numbers.
  • Page 81 Installation of the RVON-1 Card Before using the RVON-1 card with the KP-32, a few modifications need to be made to the keypanel. If the serial number on your KP-32 keypanel is 61170, you will need to update you backpanel with the Ethernet RJ-45 connection (part number - 9080-7656-002) knockout present.
  • Page 82 Installation The placement of the spacer and screw position on the RVON-1 card. Figure 3. Replace the GPI/O board. Re-attach the backplate to the KP-32 keypanel. Be sure to secure the spacer with a screw in the back plate. See Figure 2 on page 15 Replace the cover on the KP-32 keypanel.
  • Page 83 Addresses and the RVON-1 Gently secure the board in place The J37 connector on the KP-812 board. Figure 5. NOTE: Be sure the orientation of the board is correct, otherwise undesirable effects may occur. Make sure the RJ-45 connection is positioned so it will fit through the specified knockout on the back cover. When installing the RVON-1 card in an existing KP-32 or KP-812, each keypanel needs to be upgraded to include the following: KP-32 •...
  • Page 84 Installation Configure the RVON-1 from the KP-32 To use the RVON-1 with the KP-32, the KP-32 firmware must be at version 2.0.0 or higher. In turn, the firmware requires that larger flash chips be used as well (see See “Flash Chip replacement part numbers.” on page 14.). TOP LEVEL MENU, SERVICE, RVON SETUP Set the IP Address from the Service Level Menu The RVON-1 card, when shipped has a default IP Address already configured.
  • Page 85 Configure the RVON-1 from the KP-32 Press PGM. The actual Gateway IP Address appears. Enter the first number in the Gateway IP Address. This activates the first octet of the Gateway IP Address and clears the rest of the address. Press PGM.
  • Page 86 Installation Configure the RVON-1 from the KP-812 TOP LEVEL MENU, SERVICE, RVON SETUP Set the IP Address from the Service Level Menu The RVON-1 card, when shipped has a default IP Address already configured. This must be changed in order for the RVON-1 card to function properly because the pre-configured IP Address may not work with you network.
  • Page 87 Configure the RVON-8 using AZedit to contact the RVON-1 Enter the first number in the Gateway IP Address. This activates the first octet of the Gateway IP Address and clears the rest of the address. Tap the encoder knob. This confirms the first octet in the Gateway IP Address and moves you to the second octet. NOTE: Press PGM to skip over any octet that does not need modifications.
  • Page 88 Installation Right click on an RVON-8 card and select RVON-8 Configuration The RVON-8 Configuration screen appears. NOTE: The RVON-8 you use should be already configured. If it is not configured, refer to your RVON-8 Card User Manual. Remember, the RVON-1 has only one channel that can be configured. In the RVON-8 Channel drop down list, select the channel that will be used to communicate to the RVON-1 card across network.
  • Page 89 Download RVON-1 Firmware Through AZedit NOTE: AZedit sends firmware directly to the RVON-1 card over Ethernet. This is different from other I/O cards (except the RVON-8) that receive the firmware from the Master Controller. For this reason, verify the PC running AZedit is able to contact the RVON-1 card via the network, or is configured with a Gateway IP Address that can contact the RVON card.
  • Page 90 Configuration Using the Browse feature, browse to the file to be downloaded. Click Open. The Download Device Firmware screen appears. Click Begin Download. The download begins. Click OK. The RVON-1 firmware download is complete. This takes a minute or two to occur. WARNING!: Do NOT power down the keypanel until you have verified the new version information from AZedit.

  • Page 91: Basic Network Configuration

    CHAPTER 16 Basic Network Configuration Basic Network Configuration This section covers basic network configuration set-up and testing. Also covered are basic concepts and operations, including the difference between LAN and WAN networks and how IP Addressing is used. In a networked environment, such as a company, typically there are many computers connected together using a router or a switch.
  • Page 92 A wide area network (WAN) connects two or more LANs and can span a relatively large geographical area. For example, Telex Headquarters in Burnsville, MN is connected to several branch offices in Nebraska and Arkansas over a WAN. The largest WAN in existence is the Internet.
  • Page 93 80 is used for HTTP traffic. When you type an address into the address bar of a web browser, your computer goes to find an IP Address for the url you are requesting (http://www.telex.com). To obtain this address, the computer contacts a DNS server (Domain Name Server).
  • Page 94 Basic Network Configuration Packet Translation TABLE 2. Packet before Translation Source Port IP Address Number 10.2.100.1 1031 Internet From 192.156.136.22 Internet Amazingly, all the address translation that occurs takes place automatically in order to make web browsing and other functions easier.
  • Page 95 Basic Network Configuration To find your IP Address using ipconfig, do the following: From the Start Menu, open a Command Prompt screen. At the prompt, type ipconfig, then press Enter. The IP configurations appear for your machine, such as the DNS suffix, IP Address, Subnet Mask, and Default Gateway. At the prompt, type Exit to close the screen.
  • Page 96 Basic Network Configuration At the Run command, type CMD to open a Command Prompt screen. At the prompt, type the IP Address of the computer you wish to ping (for example, 10.2.100.130). Press Enter. NOTE: If the computer you are pinging is not responding to the ping, you will receive a time-out message in the command prompt screen.

  • Page 97: Rvon Configuration

    Ports necessary for RVON card functionality. TABLE 4. Port Port Description 2076 UDP Call Control Signalling 2077 UDP Audio Packets 2079 UDP Telex Proprietary Signalling 2080 TCP Telex Keypanel Protocol 2081 UDP Pass Through Serial 2082 TCP Firmware Download 2100 Remote Administration...

  • Page 98: Network Terminology

    A DNS Server is an Internet service that translates domain names (for example, in the URL http:// www.telex.com, the domain name is the telex.com) into IP Addresses. The Internet is based on IP Addresses which are numeric and since domain names are alphabetic, they are easier to remember. Every time a...
  • Page 99 Network Terminology Gateway A gateway is a node on a network that serves as an entrance to another network. The gateway routes traffic from a computer to an outside network that is serving the web pages. For example, the gateway for a home computer is the ISP provider that connects the user to the Internet.
  • Page 100 A wide area network connects two or more LANs and can span a relatively large geographical area. For example, Telex Headquarters in Burnsville, MN is connected to several of its branch offices in Nebraska and Arkansas over the wide area network. The largest WAN is the Internet.

  • Page 101: Rvon Serial And Telnet Commands

    RVON Serial and Telnet Commands RVON card programming can be done via direct serial or telnet connection. There are several physical connections to an RVON board: • Direct serial through custom debug cable (J20 6-pin bottom front) The customer debug cable always functions as the general-purpose debug tool. •...
  • Page 102 At the prompt, type Telnet (The IP Address is the IP Address assigned to the RVON-1 card). Press Enter. The RVON logon screen appears. In the logon field, type the RVON logon (default = telex). Press Enter. In the password field, type the RVON password (default = password).
  • Page 103 How to Configure the RVON-1 using Telnet Press Enter. A prompt appears. Type dbgcmd to access the debug command screens. Press Enter. An MXP prompt appears. At the prompt, type Show. Press Enter. The show commands screen and MXP prompt appears. At the MXP prompt, type the show command you want to see (for example, “show rvon”).
  • Page 104 Allows you to set the baud rate (50-38400) Allows you to set the username for the RVON-1 card. By default the user name is “telex” Allows you to set the password for the RVON-1 card. By default, the password is “password”...
  • Page 105 How to Configure the RVON-1 using Telnet set channel dest_channel set channel channel_codec set channel input_gain set channel output_gain set the channel onhook set channel offhook Allows you to edit the destination channel of the device the RVON-1 will talk with Allows you to edit the CODEC to be used for transferring the data between the two devices Allows you to edit the input gain for the RVON-1 card...
  • Page 106 12000 Portland Avenue South • Burnsville, MN 55337 • U.S.A.

This manual is also suitable for:

Kp-12Kp-32Lcp-32

Table of Contents