Fujitsu AirStage AS A009GCGH Series Installation Manual
Indoor unit (wall mounted type)
Hide thumbs
Also See for AirStage AS A009GCGH Series:
- Design & technical manual (1092 pages) ,
- Installation manual (14 pages) ,
- Operating manual (8 pages)
Table of Contents
Quick Links
EEV internal model
AS*A004GCGH
AS*A007GCGH
AS*A009GCGH
AS*A012GCGH
AS*A014GCGH
EEV external model
AS*E004GCEH
AS*E007GCEH
AS*E009GCEH
AS*E012GCEH
AS*E014GCEH
Refer to the rating label for the serial number, manufactured
year and month.
TM
INSTALLATION MANUAL
INSTALLATIONSANLEITUNG
MANUEL D'INSTALLATION
UNITÉ INTÉRIEURE (Type montage mural)
MANUAL DE INSTALACIÓN
UNIDAD INTERIOR (Tipo montado en pared)
Únicamente para personal de servicio autorizado.
MANUALE DI INSTALLAZIONE
UNITÀ INTERNA (tipo montato a parete)
A uso esclusivo del personale tecnico autorizzato.
ΕΓΧΕΙΡΙΔΙΟ ΕΓΚΑΤΑΣΤΑΣΗΣ
ΕΣΩΤΕΡΙΚΗ ΜΟΝΑΔΑ (Επιτοιχιος Τύπος)
Μόνο για εξουσιοδοτημένο τεχνικό προσωπικό.
MANUAL DE INSTALAÇÃO
РУКОВОДСТВО ПО УСТАНОВКЕ
ВНУТРЕННИЙ МОДУЛЬ (настенного типа)
Только для авторизованного обслуживающего персонала.
INDOOR UNIT (Wall mounted type)
For authorized service personnel only.
INNENGERÄT (wandmontierter Typ)
Nur für autorisiertes Fachpersonal.
Pour le personnel agréé uniquement.
UNIDADE INTERIOR (Tipo mural)
Apenas para técnicos autorizados.
MONTAJ KILAVUZU
İÇ ÜNİTE (Duvara Monteli Tip)
Yalnızca yetkili servis personeli için.
[Original instructions]
PART No. 9373370482
MADE IN P.R.C.
Table of Contents
Related Manuals for Fujitsu AirStage AS A009GCGH Series
Summary of Contents for Fujitsu AirStage AS A009GCGH Series
- Page 1 INSTALLATION MANUAL INDOOR UNIT (Wall mounted type) For authorized service personnel only. INSTALLATIONSANLEITUNG INNENGERÄT (wandmontierter Typ) Nur für autorisiertes Fachpersonal. MANUEL D’INSTALLATION EEV internal model UNITÉ INTÉRIEURE (Type montage mural) AS*A004GCGH Pour le personnel agréé uniquement. AS*A007GCGH MANUAL DE INSTALACIÓN AS*A009GCGH AS*A012GCGH UNIDAD INTERIOR (Tipo montado en pared)
-
Page 2: Table Of Contents
INSTALLATION MANUAL This mark indicates procedures which, if improperly performed, CAUTION PART No. 9373370482 might possibly result in personal harm to the user, or damage VRF system indoor unit (Wall mounted type) to property. Read carefully all security information before use or install the air conditioner. Do not attempt to install the air conditioner or a part of the air conditioner by yourself. -
Page 3: Accessories
2.3. Accessories 3. INSTALLATION WORK Correct initial installation location is important because it is difficult to move unit after it is installed. WARNING 3.1. Selecting an installation location For installation purposes, be sure to use the parts supplied by the manufacturer or other prescribed parts. -
Page 4: Installation Dimension
3.3.3 Cutting the hole in the wall for the connecting piping 3.2. Installation dimension (1) Cut a hole in the wall at the posi- Wall hook bracket tion shown in the following. Unit: mm Center mark Center mark (2) Cut the hole so that the outside end is lower (5 to 10 mm) than the inside end. -
Page 5: Pipe Installation
Installing the drain cap 4.2. Pipe requirement Use a hexagonal wrench 4 mm at opposite side to No gap insert the drain cap, till the drain cap contacts the tip of drain cock. CAUTION Hexagonal Drain cock wrench Drain cap Refer to the installation manual for the outdoor unit for description of allowable pipe length and height difference. -
Page 6: Electrical Wiring
4.3.3 Pipe connection CAUTION When the flare nut is tightened properly by your hand, hold the body side coupling with a Earth (Ground) the unit. separate spanner, then tighten with a torque wrench. Do not connect the earth (ground) cable to a gas pipe, water pipe, lightning rod, or a telephone earth (ground) cable. -
Page 7: Wiring Method
B. For strand wiring 5.2. Wiring method (1) Use ring terminals with insulating sleeves as shown in the figure below to connect to the terminal block. Example (2) Securely clamp the ring terminals to the cables using an appropriate tool so that the Outdoor unit or RB unit *1 cables do not come loose. -
Page 8: Wiring
• Position and detail of the switches 5.4. Wiring You need to remove the front panel. Refer to (1) Open the intake grille. Refer to “8. FRONT “8. FRONT PANEL RE- For refrigerant PANEL REMOVAL AND INSTALLATION”. MOVAL AND INSTAL- system address Cable clamp (2) Remove the wire cover and remove the... -
Page 9: Function Setting
• Custom code setting for indoor unit Function Function Setting number Default Details number Set the DIP switch SET3 SW1, 2, referring to the figure and table below. Forced ther- mostat off DIP switch “SET3” Setting is required when connecting Switching function for a refrigerant-leak detecting device. -
Page 10: Optional Parts Wiring
6.3.2 Checking the function settings Name Application Press and hold the “MANUAL AUTO” button on the indoor unit for 3 seconds to check CNA01 Apply voltage terminal For external input the function settings. It is necessary to disconnect the power in order to return to normal CNA03 operation mode. - Page 11 NOTE : DC power supply P.C.B (*1) 12 to 24 V When connected to multiple indoor units directly, it will cause breakdown. Load Operation behavior resistance CNA01 ● Input signal type Edge (*a) The input signal type can be selected. (*b) It is switched by DIP switch on the indoor unit PCB.
-
Page 12: Finishing
6.5.2 External output • Bind the connection cable with Connection cable (Power supply cable) vinyl tape. • A twisted pair cable (22AWG) should be used. Maximum length of cable is 25m. • Bundle the piping and drain hose • Use an external input and output cable with appropriate external dimension, depending together by wrapping them with on the number of cables to be installed. -
Page 13: Front Panel Installation
8.3. Front panel installation 11. ERROR CODES (1) First, fit the lower part of the front panel, and insert top and bottom hooks. (3 top If you use a wired type remote controller, error codes will appear on the remote controller sides, 2 center) display.