Craftsman 917.270732 Owner's Manual

17 hp electric start 42" mower 6 speed transaxle lawn tractor
Owner's
Manual
ICRIIFTSMIIH°i
17 HP
ELECTRIC
START
42" MOWER
6 SPEED TRANSAXLE
LAWN TRACTOR
Model No.
917.270732
• Safety
• Assembly
• Operation
• Maintenance
• Repair Parts
CAUTION:
Read and follow all Safety
Rules and Instructions before
operating this equipment.
For answers to your questions
about this product, Call:
1-800-659-5917
Sears Craftsman
Help Line
5 am - 5 pm, Mon- Sat
Sears, Roebuck and Co., Hoffman Estates, II 60179
Visit our Craftsman website:www.sears.com/craftsman
Table of Contents
loading

Summary of Contents for Craftsman 917.270732

  • Page 1 • Repair Parts CAUTION: Read and follow all Safety Rules and Instructions before operating this equipment. Sears, Roebuck and Co., Hoffman Estates, II 60179 Visit our Craftsman website:www.sears.com/craftsman For answers to your questions about this product, Call: 1-800-659-5917 Sears Craftsman Help Line...
  • Page 2: Limited Two-Year Warranty

    Craftsman nearest Sears Service Center. will apply. This warranty applies only while this product is in the United States.
  • Page 3: General Operation

    IMPORTANT: This cutting machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death. GENERAL OPERATION • Read, understand, and follow all instructions in the manual and on the machine before starting.
  • Page 4 • Keep children out of the mowing and under the watchful care of another responsible adult. • Be alert and turn machine off if children enter the area. • Before and when backing, look behind and down for small children. •...
  • Page 5: Customer Responsibilities

    A, Look for this symbol to point out impor- tant safety precautions. It means CAU- TION!!! BECOME AWARE!!! YOUR SAFETY IS INVOLVED. _,CAUTION: In order to prevent acciden- tal starting when setting up, transporting, adjusting or making repairs always dis- connect spark plug wire and place wire where it cannot contact spark plug.
  • Page 6 Steering Wheel Insert [_(1) Hex Bolt 3/8-16 x 1 Steering Boot (_Washer 17/32 x 1-3/16 x 12 Gauge I_(1) Slope Sheet Steering Wheel (1) Large Flat Washer washer (1) Lock (1) Locknut 5/16-18 Steering Wheel Adapter Seat Knob Keys Video Cassette (1) Hex Bolt 5/16-18 x 1-1/4 St>terinig n...
  • Page 7: Install Steering Wheel

    Your new tractor has been assembled unassembled for shipping purposes. tractor all parts and hardware you assemble correct tools as necessary to insure proper tightness. you begin. TOOLS REQUIRED ASSEMBLY A socket wrench set will make assembly easier. Standard wrench sizes you need are listed below.
  • Page 8: Install Seat

    Battery Door INSTALL SEAT Adjust seat before tightening knob. • Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly seat to tractor. • Pivot seat upward and remove from the cardboard packing. Remove cardboard packing and discard.
  • Page 9: Check Tire Pressure

    INSTALL MULCHER PLATE (If previously removed) • Raise and hold deflector shield in upright position. • Place front of mulcher plate over front of mower deck opening and slide into place, as shown. • Hook front latch into hole on front of mower deck.
  • Page 10 These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. BATTERY CAUTION OR WARNING ENGINE ON ENGINE OFF FUEL CHOKE R N H L ATTACHMENT REVERSE CLUTCH ENGAGED ATTACHMENT CLUTCH DISENGAGED IGNITION DANGER, KEEP HANDS AND FEET AWAY...
  • Page 11 KNOWYOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY YOUR TRACTOR Compare the illustrations with your tractor to familiarize various controls and adjustments. Attachment Clutch Ammeter Throttle/Choke Control Clutch/Brake Pedal Our tractors conform to the safety standards National Standards Institute. AMMETER - Indicates charging (+) or discharging (-) of battery.
  • Page 12 The operation of any tractor can the eyes, which can result in severe eye damage. glasses or eye shields while operating your tractor or performing adjustments or repairs. over spectacles HOW TO USE YOUR TRACTOR TO SET PARKING BRAKE Your tractor is equipped with an operator presence sensing...
  • Page 13: To Operate On Hills

    For healthier and better looking lawns, mow often and after moderate growth. • For best cutting performance, over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height. TO ADJUST GAUGE WHEELS Gauge wheels are properly adjusted...
  • Page 14: Before Starting

    BEFORE STARTING THE ENGINE CHECK ENGINE OIL LEVEL • The engine in your tractor has been shipped, from the factory, already filled with summer weight oil. • Check engine oil with tractor on level ground. • Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level.
  • Page 15: Cold Weather Starting

    COLD WEATHER STARTING ( 50 ° F and below) • When engine starts, allow engine to run with the throttle control in the choke position until the engine runs roughly, then move throttle control to fast position. This may require an engine warm-up period from several seconds...
  • Page 16: General Recommendations

    MAINTENANCE SCHEDULE AS YOU COMPLETE .EGU R SEOV,CE Check Tire Pressure Check Brake _perati°n Check Operator Presence Interlock Systems Check for Loose Fasteners Sharpen/Replace Mower Blades Lubrication Chart Check Battery Level Clean Battery and Terminals Check Transaxle Cooling Adjust Blade Belt(s) Tension Adjust Motion Odva Belt(s) Tension Check Engine Oil Level Change Engine Oil...
  • Page 17 TRACTOR Always observe safety rules when performing any maintenance. BRAKE OPERATION If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See 'q-O ADJUST BRAKE" in the Service and Adjustments section of this manual).
  • Page 18 BATTERY Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life. • Keep battery and terminals • Keep battery bolts tight. • Keep small vent holes open. •...
  • Page 19: In-Line Fuel Filter

    ENGINE COOLING FINS Remove any dust, dirt or oil from engine cooling fins to prevent engine damage from overheating. • Remove screws from blower housing and lift housing and dipstick tube assembly off engine. • Cover oil fill opening to prevent entry of dirt.
  • Page 20 CLEANING of all foreign matter. i Clean engine, battery, seat, finish, etc. Keep finished surfaces and wheels free of all _]asoline, oil, etc. • Protect painted surfaces with automo- tive type wax. _kCAUTION: Before performing Depress clutch/brake pedal fully and set parking brake. Place gearshift lever in neutral (N) position.
  • Page 21 TO LEVEL MOWER HOUSING Adjust the mower while tractor is parked on level ground or driveway. bres are properly inflated (See =PROD- UCT SPECIFICATIONS" section of this manual). If tires are over or underinflated, you will not properly adjust your mower. SIDE-TO-SIDE ADJUSTMENT •...
  • Page 22 TO REPLACE MOWER BLADE DRIVE BELT The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake. BELT REMOVAL - • Remove mower from tractor (See "TO REMOVE MOWER" in this section of this manual).
  • Page 23 NOTE: When the tractor rear wheels move freely, the transaxle is in neutral. • Loosen adjustment bolt in front of the right rear wheel. • Position the gear shift lever in the neutral (N) position. • Tighten adjustment bolt securely. NOTE: If additional clearance is needed to get to adjustment bolt, move mower...
  • Page 24 REPLACING BATTERY ACAUTION: Do not shod battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands,rings,etc. Positive terminal must be connected first to prevent sparking from accidental grounding.
  • Page 25 • Check that holes "A" in governor control lever and hole in governor plate line-up. If holes "A" are not aligned, loosen clamp screw and move throttle cable until holes are aligned. Tighten clamp screw se- curely. Governor Governor Control Lever Control Plate Holes "A"...
  • Page 26: Engine Oil

    Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. CAUTION: Never store the tractor w_th gasoline in the tank inside a building where fumes may reach an open flame or spark.
  • Page 27: Troubleshooting Chart

    TROUBLESHOOTING CHART PROBLEM CAUSE • Out of fuel. Will not start • Engine not "CHOKED" properly. • Engine • Bad spark plug. • Dirty air filter. • Dirty fuel filter, • Water in fuel. • Loose or damaged • Carburetor •...
  • Page 28 TROUBLESHOOTING CHART PROBLEM CAUSE Engine clicks but • Weak or dead battery. will not start • Corroded battery terminals. • Loose or damaged wiring. • Faulty solenoid or starter. Loss of power Cutting too much grass/too fast. Throttle in "CHOKE" position.
  • Page 29 TROUBLESHOOTING CHART PROBLEM CAUSE Poor cut- uneven • Worn, bent or loose blade. • Mower deck not level. • Buildup of grass, leaves, and trash under mower. • Bent blade mandrel. • Clogged mower deck vent holes from buildup of grass, leaves, and trash around Mower blades will...
  • Page 30 TROUBLESHOOTING CHART PROBLEM CAUSE Battery will not • Bad battery cell(s). • Poor cable connections. charge • Faulty regulator (if so equipped). • Faulty alternator. Engine "backfires" • Engine throttle control not when turning set at "SLOW" position for 30 seconds engine "OFF"...
  • Page 31 TRACTOR -- MODEL NUMBER 917.270732 SCHEMATIC AMMETER OPTIONAL) IGNITION SWITCH OWN ELECTRICAL BECAUSE OF THIS, THE BRIGHTNESS WILL CHANGE WITH ENGINE SPEED. WILL DIM. ASTHE SPEEDED WILL BECOME THEIR BRIGHTEST. IGNITION SWITCH POSITION CIRCUIT =MAKE" M+G+A1 NONE WIRING INSULATED RUN/UGH]...
  • Page 32 TRACTOR ELECTRICAL -- MODEL NUMBER 917.270732...
  • Page 33 TRACTOR -- MODEL NUMBER 917.270732 ELECTRICAL KEY PART NOTE: Allcomponentdimensions given in U.S. inches DESCRIPTION 144925 Battery 74760412 Bolt Hex Hd 1/4-20unc x 3/4 156417 Case Battery 153664 Switch, Interlock 166181 Harness Asm Light W/4152j 4152J Bulb Light #1156 4799J Cable Battery 6 Ga 11•...
  • Page 34: Chassis And Enclosures

    TRACTOR - - MODEL NUMBER 917.270732 CHASSIS AND ENCLOSURES...
  • Page 35 I HA_ | gl'l CHASSIS AND ENCLOSURES KEY PART 16983O 169061 17060612 155272 168337X013 STD533710 155927 145660 172107)(010 159639X558 126938X 19131312 STD541437 140434 140273X599 164918X558 139976 17490508 169834 73800400 19091416 144697 161464 144696 STD522507 150127 72140606 154798 STD541437 158112 17060620 165867 154966 154207...
  • Page 36: Ground Drive

    TRACTOR -.. MODEL NUMBER 917.270732 GROUND DRIVE...
  • Page 37 TRACTOR - - MODEL NUMBER 917.270732 GROUND DRIVE PART DESCRIPTION Transaxle (See Breakdown) Peerless 206-545C 146682 Spring, Return, Brake 123666X Pulley, Transaxle 12000028 Ring, Retainer 121520X Strap, Torque 17060512 Screw 5/16-18 x 3/4 165866 Rod Shifter Fender STLT STD561210 Pin, Cotter...
  • Page 38: Steering Assembly

    TRACTOR STEERING ASSEMBLY - - MODEL NUMBER 917.270732 64&...
  • Page 39 I M/._t.,I UM - - MUUI:L STEERING ASSEMBLY KEY PART 139768 154427 169840 169839 6266H 121748X 19272016 12000029 3366R 169832 STD551137 136518 145212 156546 57079 160395 165857 165851 154406 126847X 136874 19131416 17060612 STD561210 130465 155099 152927 139769 19133812 STD541537 100711L 145054X428 121749X...
  • Page 40: Optional Equipment

    TRACTOR - - MODEL NUMBER 917.270732 ENGINE OPTIONAL EQUIPMENT Spark Arrester...
  • Page 41 TRACTOR - - MODEL NUMBER 917.270732 ENGINE KEY PART 162157 17720410 137352 165291 13280324 13200300 STO551231 169837 137180 109202X 158990 123487X 137040 124028X 17670412 17000612 19091416 STD551131 71070512 17060620 73510400 NOTE= All componentdimensions givenin U.S. inches DESCRIPTION Control, Throttle Screw, Hex Head, Thread Cutting...
  • Page 42: Seat Assembly

    Washer 13/32 X 1 X 14 Ga 155925 Pan Pnt Seat (blk) 166369 Knob Seat Adj Wingnut 121246X Bracket Pet Mounting Switch -- MODEL NUMBER 917.270732 KEY PART DESCRIPTION 121248X Bushing Snap BIk Ny150 Id 72050412 Bolt Rdhd Sht Nk 1/4-20x1-1/2...
  • Page 43: Wheels And Tires

    TRACTOR - - MODEL NUMBER 917.270732 DECALS KEY PART DESCRIPTION 156368 Decal, Oper. Instr. 171760 Decal, Replacement 171696 Decal, Hood, R.H. 171697 Decal, Hood, L.H. 165406 Decal, HP Engine 133644 Decal, Customer Maintenance 166887 Decal, Deck Mower EZ 163204 Decal, Fender, Craftsman...
  • Page 44: Lift Assembly

    TRACTOR - - MODEL NUMBER 917.270732 LIFT ASSEMBLY •...
  • Page 45 TRACTOR LIFT ASSEMBLY KEY PART NOTE: All componentdimensions given in U.S. inches - - MODEL NUMBER 917.270732 DESCRIPTION 159460 Washer Asm inner Spdng W/Plunger 159471 Shaft Asm. Lift 105767X Pin Groove 12000002 E Ring #5133-62 19211621 Washer 21/32 x 1 x 21 Ga.
  • Page 46 TRACTOR - - MODEL NUMBER 917.270732 MOWER DECK "_ 21 3 24 13--...
  • Page 47: Mower Deck

    I M/as!t.o1lt.Pl'i - - IVl!,.JUl" I. I_IUIVIDIPI'I MOWER DECK KEY PART DESCRIPTION 165892 Mower Deck Assembly, 42" STD533107 Bolt 138017 Bracket Assembly,Sway Bar, Front 165460 Bracket Sway Bar 38/42" Deck STD624008 Retainer Spring 130832 Arm, Suspension, Rear 850857 Bolt, Hex 3/8-24 x 1.25 Gr. 8 STD551137 Washer, Lock 140296...
  • Page 48 TRACTOR -- MODEL NUMBER 917.270732 PEERLESS TRANSAXLE - - MODEL NUMBER 206-545C MODEL and SERIAl NUMBERS HERE...
  • Page 49 799021 Brake Pad (pkg of 2) 786026 Dowel Pin 792076A Flat Washer .312 ID x .059W - - MODEL NUMBER 917.270732 206-545C KEY PART DESCRIPTION Brake Lever 790079 Screw 1/4 - 20 x 1-1 /4" 792073A Screw 1/4 - 20 x 2 1/4"...
  • Page 50 TRACTOR - - MODEL NUMBER 917.270732 BRIGGS ENGINE-MODEL NUMBER 311707, TYPE NUMBER 0132-E3 1022 1023 1034 1029 _ 307_ 1033 VALVE OVERHAUL KIT REQUIRES SPECIAL TOOLS TO INSTALL. SEE REPAIR 1022 INSTRUCTIONMANUAL, 1019 LABEL KIT 868_) I 1058 OWNER'S MANUAL...
  • Page 51 TRACTOR 3RIGGS ENGINE-MODEL NUMBER 311707, TYPE NUMBER 0132-E3 LMTICARBURETOR PART NUMBER LOCATIONS THiS CARBURETOR SERVICES BOTH CHOKE-A-MATIC AND MANUAL CHOKE SYSTEMS 977 CARBURETOR GA._SKETSET - - MODEL NUMBER 917.270732 754_ 51 0...
  • Page 52 TRACTOR - - MODEL NUMBER 917.270732 BRIGGS ENGINE-MODEL NUMBER 311707, TYPE NUMBER 0132-E3 797A 1044 _ 1051 1051 ,',' 783A 1036 LABEL-EMISSIONS...
  • Page 53 I M/ILi.p I Ul'l - - IVIUUr.i. I_IUIVIDr'I'I _ I I ./..! UI Of. BRIGGS ENGINE-MODEL NUMBER 311707, TYPE NUMBER 0132-E3 NIKKI 130A 633A 117A i]I 137A 276A 121A CARBURETOR OVERHAUL 276A 95A_ 117Aq_) lO4A _' 127A0 105A 633 (_) 231A 137A O 977A CARBURETOR...
  • Page 54 BRIGGS ENGINE-MODEL NUMBER KEY PART DESCRIPTION 690156 Cylinder Assembly 399265 Bushing/Seal 391086 Seal-Oil 494238 Sump-Engine 690188 Head-Cylinder 692410 Or+ Gasket-Cylinder 495735 Breather Assembly 27803 ¢r Gasket-Breather 691666 Screw (Breather Assembly) 691328 Tube-Breather 271916 "# Gasket-Crankcase Thick, Std.) 271997 ¢r Gasket-Crankcase Thick) 271996 Gasket-Crankcase...
  • Page 55 TRACTOR - - MODEL NUMBER 917.270732 3RIGGS ENGINE-MODEL NUMBER 311707, TYPE NUMBER 0132-E3 "EY PART DESCRIPTION Motor-Starter (For Steel Ring 693551 Gear Only) 497595 Motor-Starter (For Plastic Ring Gear Only) ;10 690323 Screw (Starter Motor) ;11 497608 Brush Set 692127 Screw (Mounting Bracket) ;33 495859...
  • Page 59 SUGGESTED GUIDE FOR SIGHTING SIGHTING _CUT GUIDE TH-i_S Operate your Tractor up and down the face of slopes (not greater than 15°), never across the face. Make turns gradu- ally to prevent tipping or loss of control. Exercise extreme caution when changing SLOPES FOR SAFE OPERATION ONLY RIDE UP AND DOWN HILL,...
  • Page 60 For repair of major brand appliances no matter who made it, no matter who sold it! 1-800-4-MY-HOME (1-800-469-4663) To bring in products such as vacuums, lawn equipment the location of your nearest Sears Parts & Repair 1 800 488 1222 "...

Table of Contents